* [PATCH v4 0/3] arm64: dts: allwinner: add A733/Cubie A7S support
@ 2026-11-19 18:09 Enzo Adriano
2026-11-19 18:09 ` [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S Enzo Adriano
` (2 more replies)
0 siblings, 3 replies; 7+ messages in thread
From: Enzo Adriano @ 2026-11-19 18:09 UTC (permalink / raw)
To: andre.przywara, robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel
Cc: Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi,
linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini,
Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid
This series adds the initial Allwinner A733 and Radxa Cubie A7S device
trees for UART0, the AXP318W PMIC and 3.3 V microSD.
Base: sunxi/for-next (03b3355ed7a39b4416f0d0a39061479b1aa13196).
Previous posting (v3):
https://lore.kernel.org/r/cover.1794227241.git.enzo.adriano.code@gmail.com
Changes in v4:
- 1/3: Carry Alexander Sverdlin's Reviewed-by.
- 2/3: Add a one-cluster CPU map and A55/A76 PMUs on PPI 7, using
GIC ppi-partitions. Change #interrupt-cells from 3 to 4 and add a
fourth cell to every GIC interrupt specifier. Drop Vinicius Pedrosa's
Tested-by because of the interrupt encoding change.
- 3/3: Sort root nodes and put status last. Move boot history below ---.
Runtime dependencies in application order:
[1] AXP318W PMIC v8
https://lore.kernel.org/r/20260910-axp318-regulator-v8-0-e906a61a7f3d@baylibre.com
[2] Pinctrl IRQ-bank v3
https://lore.kernel.org/r/20261025142412.112216-1-pmazzini@gmail.com
[3] A733 8250_dw v2, patches 1-4
https://lore.kernel.org/r/cover.1792439398.git.vinicius.eduardo.pedrosa@gmail.com
[4] Firmware-clock v2 for vendor-firmware warm reboot
https://lore.kernel.org/r/20261112-a733-fwclk-v2@gmail.com
[5] Pinctrl voltage-mode v3
https://lore.kernel.org/r/20261109-a733-pinctrl-v3@gmail.com
A7S DTB/schema checks need [1] 3/5, [2] 2/3 and [3] 3/4 before v4.
Validation: clean git am, arm64 defconfig Image, arm/sunxi.yaml binding
check and warning-free A7S W=2 CHECK_DTBS=y. The compiled DTB has one
eight-core cluster and two disjoint PMU partitions.
A November 18 RAM boot on Cubie A7S with vendor firmware used the base
and runtime dependencies above. Two context-only adaptations were needed:
PMIC v8 regulator allocation context and pinctrl voltage-mode v3 IRQ-bank
map context. CPUs 0-7 came online in one cluster. The A55 PMU covered
CPUs 0-5 and the A76 PMU CPUs 6-7; cycles and instructions counted and
PPI 7 overflow samples were observed on each CPU. The timer, console,
AXP318W probe and MMC0 read-only transfers worked; warm reboot returned
to vendor Linux unaided.
Untested: PMIC/NMI interrupt delivery, card writes, hotplug, suspend,
power-off, CPU capacity, 1.8 V switching, other UART/I2C and storage
instances, RTC alarms, EL2/ITS/MSI, and physical BLDO2 voltage.
Enzo Adriano (3):
dt-bindings: arm: sunxi: document Radxa Cubie A7S
arm64: dts: allwinner: add A733 SoC description
arm64: dts: allwinner: add Radxa Cubie A7S board
.../devicetree/bindings/arm/sunxi.yaml | 5 +
arch/arm64/boot/dts/allwinner/Makefile | 1 +
.../dts/allwinner/sun60i-a733-cubie-a7s.dts | 287 ++++++++
.../arm64/boot/dts/allwinner/sun60i-a733.dtsi | 657 ++++++++++++++++++
4 files changed, 950 insertions(+)
create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts
create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi
base-commit: 03b3355ed7a39b4416f0d0a39061479b1aa13196
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S 2026-11-19 18:09 [PATCH v4 0/3] arm64: dts: allwinner: add A733/Cubie A7S support Enzo Adriano @ 2026-11-19 18:09 ` Enzo Adriano 2026-11-21 23:40 ` Andre Przywara 2026-11-19 18:09 ` [PATCH v4 2/3] arm64: dts: allwinner: add A733 SoC description Enzo Adriano 2026-11-19 18:09 ` [PATCH v4 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board Enzo Adriano 2 siblings, 1 reply; 7+ messages in thread From: Enzo Adriano @ 2026-11-19 18:09 UTC (permalink / raw) To: andre.przywara, robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel Cc: Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini, Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid, Krzysztof Kozlowski Document the Radxa Cubie A7S board and Allwinner A733 SoC compatibles for the accompanying initial board device tree, so it can be identified and validated. Reviewed-by: Alexander Sverdlin <alex@sverdlin.org> Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> Signed-off-by: Enzo Adriano <enzo.adriano.code@gmail.com> --- Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ 1 file changed, 5 insertions(+) diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml index 7da84e2de748..d32689b7113d 100644 --- a/Documentation/devicetree/bindings/arm/sunxi.yaml +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml @@ -857,6 +857,11 @@ properties: - const: radxa,cubie-a5e - const: allwinner,sun55i-a527 + - description: Radxa Cubie A7S + items: + - const: radxa,cubie-a7s + - const: allwinner,sun60i-a733 + - description: Remix Mini PC items: - const: jide,remix-mini-pc ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S 2026-11-19 18:09 ` [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S Enzo Adriano @ 2026-11-21 23:40 ` Andre Przywara 0 siblings, 0 replies; 7+ messages in thread From: Andre Przywara @ 2026-11-21 23:40 UTC (permalink / raw) To: Enzo Adriano Cc: robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel, Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini, Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid, Krzysztof Kozlowski On Thu, 19 Nov 2026 13:09:17 -0500 Enzo Adriano <enzo.adriano.code@gmail.com> wrote: > Document the Radxa Cubie A7S board and Allwinner A733 SoC compatibles > for the accompanying initial board device tree, so it can be identified > and validated. > > Reviewed-by: Alexander Sverdlin <alex@sverdlin.org> > Acked-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com> > Signed-off-by: Enzo Adriano <enzo.adriano.code@gmail.com> > --- > Documentation/devicetree/bindings/arm/sunxi.yaml | 5 +++++ > 1 file changed, 5 insertions(+) > > diff --git a/Documentation/devicetree/bindings/arm/sunxi.yaml b/Documentation/devicetree/bindings/arm/sunxi.yaml > index 7da84e2de748..d32689b7113d 100644 > --- a/Documentation/devicetree/bindings/arm/sunxi.yaml > +++ b/Documentation/devicetree/bindings/arm/sunxi.yaml > @@ -857,6 +857,11 @@ properties: > - const: radxa,cubie-a5e > - const: allwinner,sun55i-a527 > > + - description: Radxa Cubie A7S > + items: > + - const: radxa,cubie-a7s > + - const: allwinner,sun60i-a733 > + Can you please add the A7A and name as well? I will send the .dts patch shortly, but having the name ready would reduce the churn and avoid conflicts. Cheers, Andre > - description: Remix Mini PC > items: > - const: jide,remix-mini-pc > ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v4 2/3] arm64: dts: allwinner: add A733 SoC description 2026-11-19 18:09 [PATCH v4 0/3] arm64: dts: allwinner: add A733/Cubie A7S support Enzo Adriano 2026-11-19 18:09 ` [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S Enzo Adriano @ 2026-11-19 18:09 ` Enzo Adriano 2026-11-21 10:23 ` Andre Przywara 2026-11-19 18:09 ` [PATCH v4 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board Enzo Adriano 2 siblings, 1 reply; 7+ messages in thread From: Enzo Adriano @ 2026-11-19 18:09 UTC (permalink / raw) To: andre.przywara, robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel Cc: Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini, Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid Provide the SoC description needed for the Cubie A7S console, PMIC and microSD support. Describe the CPUs, PSCI, architectural timers, GIC, RTC, main and always-on clock/reset and pin controllers. Include the main and R-domain UART/I2C instances and MMC0-2 with their pin groups. The GIC maintenance PPI 9 and ARMv8.2 EL2 virtual-timer PPI 12 follow the A733 User Manual v1.00, section 12.2.3. The GICD/GICR/ITS windows and noncoherent attributes follow Andre Przywara's public A733 reference and the A523 precedent. The CPUX interconnect diagram in section 5.1.2 supports noncoherency as an integration inference. The ITS stays disabled pending its clock/reset and MSI integration. Describe one DynamIQ cluster sharing L3, as shown in the A733 User Manual v1.00, section 5.1.2 (figure 5-1), and partition PPI 7 (section 12.2.3, table 12-1) between the Cortex-A55 and Cortex-A76 PMUs so each probes its own core type. Defer capacity-dmips-mhz until it is measured on A733. Link: https://gist.githubusercontent.com/apritzel/60fd7379b9560a15b8b352986b69d39f/raw/efd9cdf8f26ba5b0c7e138f093af44a1cf322469/sun60i-a733.dts Signed-off-by: Enzo Adriano <enzo.adriano.code@gmail.com> --- The November 18 v4 RAM boot on Cubie A7S with vendor firmware exercised console, R-I2C0/PMIC probe and MMC0 read-only transfers. CPUs 0-7 were in one cluster, with the A55 PMU on CPUs 0-5 and the A76 PMU on CPUs 6-7 counting and receiving PPI 7 overflow interrupts on each CPU. PMIC/NMI interrupt delivery, EL2 interrupt delivery and ITS/MSI were not tested. Dropped Vinicius Pedrosa's Tested-by because v4 changes the GIC interrupt encoding. .../arm64/boot/dts/allwinner/sun60i-a733.dtsi | 657 ++++++++++++++++++ 1 file changed, 657 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi b/arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi new file mode 100644 index 000000000000..b0f642f37803 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi @@ -0,0 +1,657 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR MIT) + +#include <dt-bindings/clock/sun6i-rtc.h> +#include <dt-bindings/clock/allwinner,sun60i-a733-ccu.h> +#include <dt-bindings/clock/allwinner,sun60i-a733-r-ccu.h> +#include <dt-bindings/interrupt-controller/arm-gic.h> +#include <dt-bindings/reset/allwinner,sun60i-a733-ccu.h> +#include <dt-bindings/reset/allwinner,sun60i-a733-r-ccu.h> + +/ { + #address-cells = <2>; + #size-cells = <2>; + interrupt-parent = <&gic>; + + cpus { + #address-cells = <1>; + #size-cells = <0>; + + cpu-map { + cluster0 { + core0 { + cpu = <&cpu0>; + }; + + core1 { + cpu = <&cpu1>; + }; + + core2 { + cpu = <&cpu2>; + }; + + core3 { + cpu = <&cpu3>; + }; + + core4 { + cpu = <&cpu4>; + }; + + core5 { + cpu = <&cpu5>; + }; + + core6 { + cpu = <&cpu6>; + }; + + core7 { + cpu = <&cpu7>; + }; + }; + }; + + cpu0: cpu@0 { + compatible = "arm,cortex-a55"; + device_type = "cpu"; + reg = <0x0>; + enable-method = "psci"; + }; + + cpu1: cpu@100 { + compatible = "arm,cortex-a55"; + device_type = "cpu"; + reg = <0x100>; + enable-method = "psci"; + }; + + cpu2: cpu@200 { + compatible = "arm,cortex-a55"; + device_type = "cpu"; + reg = <0x200>; + enable-method = "psci"; + }; + + cpu3: cpu@300 { + compatible = "arm,cortex-a55"; + device_type = "cpu"; + reg = <0x300>; + enable-method = "psci"; + }; + + cpu4: cpu@400 { + compatible = "arm,cortex-a55"; + device_type = "cpu"; + reg = <0x400>; + enable-method = "psci"; + }; + + cpu5: cpu@500 { + compatible = "arm,cortex-a55"; + device_type = "cpu"; + reg = <0x500>; + enable-method = "psci"; + }; + + cpu6: cpu@600 { + compatible = "arm,cortex-a76"; + device_type = "cpu"; + reg = <0x600>; + enable-method = "psci"; + }; + + cpu7: cpu@700 { + compatible = "arm,cortex-a76"; + device_type = "cpu"; + reg = <0x700>; + enable-method = "psci"; + }; + }; + + osc: osc-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + }; + + pmu-a55 { + compatible = "arm,cortex-a55-pmu"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_a55>; + }; + + pmu-a76 { + compatible = "arm,cortex-a76-pmu"; + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_a76>; + }; + + psci { + compatible = "arm,psci-0.2"; + method = "smc"; + }; + + timer { + compatible = "arm,armv8-timer"; + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH 0>; + arm,no-tick-in-suspend; + }; + + soc@0 { + compatible = "simple-bus"; + #address-cells = <1>; + #size-cells = <1>; + ranges = <0x0 0x0 0x0 0x40000000>; + + pio: pinctrl@2000000 { + compatible = "allwinner,sun60i-a733-pinctrl"; + reg = <0x02000000 0x800>; + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_APB1>, <&osc>, <&rtc CLK_OSC32K>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + + mmc0_pins: mmc0-pins { + pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; + function = "mmc0"; + allwinner,pinmux = <2>; + drive-strength = <30>; + bias-pull-up; + }; + + mmc1_pins: mmc1-pins { + pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; + function = "mmc1"; + allwinner,pinmux = <2>; + drive-strength = <30>; + bias-pull-up; + }; + + mmc2_pins: mmc2-pins { + pins = "PC5", "PC6", "PC8", "PC9", "PC10", "PC11", + "PC13", "PC14", "PC15", "PC16"; + function = "mmc2"; + allwinner,pinmux = <3>; + drive-strength = <30>; + bias-pull-up; + }; + + uart0_pb_pins: uart0-pb-pins { + pins = "PB9", "PB10"; + function = "uart0"; + allwinner,pinmux = <2>; + }; + }; + + ccu: clock-controller@2002000 { + compatible = "allwinner,sun60i-a733-ccu"; + reg = <0x02002000 0x2000>; + clocks = <&osc>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>, + <&rtc CLK_OSC32K_FANOUT>; + clock-names = "hosc", "losc", "iosc", "losc-fanout"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + uart0: serial@2500000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02500000 0x400>; + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART0>; + resets = <&ccu RST_BUS_UART0>; + status = "disabled"; + }; + + uart1: serial@2501000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02501000 0x400>; + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART1>; + resets = <&ccu RST_BUS_UART1>; + status = "disabled"; + }; + + uart2: serial@2502000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02502000 0x400>; + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART2>; + resets = <&ccu RST_BUS_UART2>; + status = "disabled"; + }; + + uart3: serial@2503000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02503000 0x400>; + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART3>; + resets = <&ccu RST_BUS_UART3>; + status = "disabled"; + }; + + uart4: serial@2504000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02504000 0x400>; + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART4>; + resets = <&ccu RST_BUS_UART4>; + status = "disabled"; + }; + + uart5: serial@2505000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02505000 0x400>; + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART5>; + resets = <&ccu RST_BUS_UART5>; + status = "disabled"; + }; + + uart6: serial@2506000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x02506000 0x400>; + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&ccu CLK_BUS_UART6>; + resets = <&ccu RST_BUS_UART6>; + status = "disabled"; + }; + + i2c0: i2c@2510000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02510000 0x400>; + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C0>; + resets = <&ccu RST_BUS_I2C0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c1: i2c@2511000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02511000 0x400>; + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C1>; + resets = <&ccu RST_BUS_I2C1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c2: i2c@2512000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02512000 0x400>; + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C2>; + resets = <&ccu RST_BUS_I2C2>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c3: i2c@2513000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02513000 0x400>; + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C3>; + resets = <&ccu RST_BUS_I2C3>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c4: i2c@2514000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02514000 0x400>; + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C4>; + resets = <&ccu RST_BUS_I2C4>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c5: i2c@2515000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02515000 0x400>; + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C5>; + resets = <&ccu RST_BUS_I2C5>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c6: i2c@2516000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02516000 0x400>; + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C6>; + resets = <&ccu RST_BUS_I2C6>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c7: i2c@2517000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02517000 0x400>; + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C7>; + resets = <&ccu RST_BUS_I2C7>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c8: i2c@2518000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02518000 0x400>; + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C8>; + resets = <&ccu RST_BUS_I2C8>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c9: i2c@2519000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x02519000 0x400>; + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C9>; + resets = <&ccu RST_BUS_I2C9>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c10: i2c@251a000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x0251a000 0x400>; + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C10>; + resets = <&ccu RST_BUS_I2C10>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c11: i2c@251b000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x0251b000 0x400>; + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C11>; + resets = <&ccu RST_BUS_I2C11>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + i2c12: i2c@251c000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x0251c000 0x400>; + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_I2C12>; + resets = <&ccu RST_BUS_I2C12>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + gic: interrupt-controller@3400000 { + compatible = "arm,gic-v3"; + reg = <0x03400000 0x10000>, <0x03460000 0x100000>; + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; + dma-noncoherent; + interrupt-controller; + #interrupt-cells = <4>; + #address-cells = <1>; + #size-cells = <1>; + ranges; + + its: msi-controller@3440000 { + compatible = "arm,gic-v3-its"; + reg = <0x03440000 0x20000>; + msi-controller; + #msi-cells = <1>; + dma-noncoherent; + status = "disabled"; + }; + + ppi-partitions { + ppi_a55: interrupt-partition-0 { + affinity = <&cpu0 &cpu1 &cpu2 &cpu3 &cpu4 &cpu5>; + }; + + ppi_a76: interrupt-partition-1 { + affinity = <&cpu6 &cpu7>; + }; + }; + }; + + mmc0: mmc@4020000 { + compatible = "allwinner,sun60i-a733-mmc", + "allwinner,sun20i-d1-mmc"; + reg = <0x04020000 0x1000>; + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC0>; + reset-names = "ahb"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc0_pins>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + mmc1: mmc@4021000 { + compatible = "allwinner,sun60i-a733-mmc", + "allwinner,sun20i-d1-mmc"; + reg = <0x04021000 0x1000>; + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC1>; + reset-names = "ahb"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc1_pins>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + mmc2: mmc@4022000 { + compatible = "allwinner,sun60i-a733-mmc", + "allwinner,sun20i-d1-mmc"; + reg = <0x04022000 0x1000>; + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; + clock-names = "ahb", "mmc"; + resets = <&ccu RST_BUS_MMC2>; + reset-names = "ahb"; + pinctrl-names = "default"; + pinctrl-0 = <&mmc2_pins>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + r_ccu: clock-controller@7010000 { + compatible = "allwinner,sun60i-a733-r-ccu"; + reg = <0x07010000 0x250>; + clocks = <&osc>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>, + <&ccu CLK_SYS_24M>, <&ccu CLK_PLL_PERIPH0_200M>, + <&ccu CLK_PLL_PERIPH0_300M>, + <&ccu CLK_PLL_PERIPH1_300M>; + clock-names = "hosc", "losc", "iosc", "sys-24m", + "pll-periph0-200m", "pll-periph0-300m", + "pll-periph1-300m"; + #clock-cells = <1>; + #reset-cells = <1>; + }; + + nmi_intc: interrupt-controller@7010320 { + compatible = "allwinner,sun60i-a733-nmi", + "allwinner,sun55i-a523-nmi"; + reg = <0x07010320 0xc>; + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH 0>; + interrupt-controller; + #interrupt-cells = <2>; + }; + + r_pio: pinctrl@7025000 { + compatible = "allwinner,sun60i-a733-r-pinctrl"; + reg = <0x07025000 0x800>; + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>, + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&r_ccu CLK_R_APB0>, <&osc>, <&rtc CLK_OSC32K>; + clock-names = "apb", "hosc", "losc"; + gpio-controller; + #gpio-cells = <3>; + interrupt-controller; + #interrupt-cells = <3>; + + r_i2c0_pl_pins: r-i2c0-pl-pins { + pins = "PL0", "PL1"; + function = "r_i2c0"; + allwinner,pinmux = <2>; + }; + }; + + r_uart0: serial@7080000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x07080000 0x400>; + interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&r_ccu CLK_BUS_R_UART0>; + resets = <&r_ccu RST_BUS_R_UART0>; + status = "disabled"; + }; + + r_uart1: serial@7081000 { + compatible = "allwinner,sun60i-a733-uart", + "snps,dw-apb-uart"; + reg = <0x07081000 0x400>; + interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH 0>; + reg-shift = <2>; + reg-io-width = <4>; + clocks = <&r_ccu CLK_BUS_R_UART1>; + resets = <&r_ccu RST_BUS_R_UART1>; + status = "disabled"; + }; + + r_i2c0: i2c@7083000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x07083000 0x400>; + interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&r_ccu CLK_BUS_R_I2C0>; + resets = <&r_ccu RST_BUS_R_I2C0>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + r_i2c1: i2c@7084000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x07084000 0x400>; + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&r_ccu CLK_BUS_R_I2C1>; + resets = <&r_ccu RST_BUS_R_I2C1>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + r_i2c2: i2c@7085000 { + compatible = "allwinner,sun60i-a733-i2c", + "allwinner,sun8i-v536-i2c", + "allwinner,sun6i-a31-i2c"; + reg = <0x07085000 0x400>; + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&r_ccu CLK_BUS_R_I2C2>; + resets = <&r_ccu RST_BUS_R_I2C2>; + #address-cells = <1>; + #size-cells = <0>; + status = "disabled"; + }; + + rtc: rtc@7090000 { + compatible = "allwinner,sun60i-a733-rtc", + "allwinner,sun50i-r329-rtc"; + reg = <0x07090000 0x400>; + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH 0>; + clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc>, <&r_ccu CLK_R_AHB>; + clock-names = "bus", "hosc", "ahb"; + #clock-cells = <1>; + }; + }; +}; ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 2/3] arm64: dts: allwinner: add A733 SoC description 2026-11-19 18:09 ` [PATCH v4 2/3] arm64: dts: allwinner: add A733 SoC description Enzo Adriano @ 2026-11-21 10:23 ` Andre Przywara 0 siblings, 0 replies; 7+ messages in thread From: Andre Przywara @ 2026-11-21 10:23 UTC (permalink / raw) To: Enzo Adriano Cc: robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel, Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini, Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid On Thu, 19 Nov 2026 13:09:21 -0500 Enzo Adriano <enzo.adriano.code@gmail.com> wrote: Hi, > Provide the SoC description needed for the Cubie A7S console, PMIC and > microSD support. Describe the CPUs, PSCI, architectural timers, GIC, > RTC, main and always-on clock/reset and pin controllers. Include the > main and R-domain UART/I2C instances and MMC0-2 with their pin groups. > > The GIC maintenance PPI 9 and ARMv8.2 EL2 virtual-timer PPI 12 follow > the A733 User Manual v1.00, section 12.2.3. The GICD/GICR/ITS windows > and noncoherent attributes follow Andre Przywara's public A733 > reference and the A523 precedent. The CPUX interconnect diagram in > section 5.1.2 supports noncoherency as an integration inference. The > ITS stays disabled pending its clock/reset and MSI integration. > > Describe one DynamIQ cluster sharing L3, as shown in the A733 User > Manual v1.00, section 5.1.2 (figure 5-1), and partition PPI 7 > (section 12.2.3, table 12-1) between the Cortex-A55 and Cortex-A76 > PMUs so each probes its own core type. Defer capacity-dmips-mhz > until it is measured on A733. > > Link: https://gist.githubusercontent.com/apritzel/60fd7379b9560a15b8b352986b69d39f/raw/efd9cdf8f26ba5b0c7e138f093af44a1cf322469/sun60i-a733.dts > Signed-off-by: Enzo Adriano <enzo.adriano.code@gmail.com> > --- > > The November 18 v4 RAM boot on Cubie A7S with vendor firmware exercised > console, R-I2C0/PMIC probe and MMC0 read-only transfers. CPUs 0-7 were > in one cluster, with the A55 PMU on CPUs 0-5 and the A76 PMU on CPUs > 6-7 counting and receiving PPI 7 overflow interrupts on each CPU. > PMIC/NMI interrupt delivery, EL2 interrupt delivery and ITS/MSI were > not tested. > > Dropped Vinicius Pedrosa's Tested-by because v4 changes the GIC > interrupt encoding. > > .../arm64/boot/dts/allwinner/sun60i-a733.dtsi | 657 ++++++++++++++++++ > 1 file changed, 657 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi > > diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi b/arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi > new file mode 100644 > index 000000000000..b0f642f37803 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun60i-a733.dtsi > @@ -0,0 +1,657 @@ > +// SPDX-License-Identifier: (GPL-2.0-only OR MIT) > + > +#include <dt-bindings/clock/sun6i-rtc.h> > +#include <dt-bindings/clock/allwinner,sun60i-a733-ccu.h> > +#include <dt-bindings/clock/allwinner,sun60i-a733-r-ccu.h> > +#include <dt-bindings/interrupt-controller/arm-gic.h> > +#include <dt-bindings/reset/allwinner,sun60i-a733-ccu.h> > +#include <dt-bindings/reset/allwinner,sun60i-a733-r-ccu.h> > + > +/ { > + #address-cells = <2>; > + #size-cells = <2>; > + interrupt-parent = <&gic>; > + > + cpus { > + #address-cells = <1>; > + #size-cells = <0>; > + > + cpu-map { So what's the purpose of this cpu-map really if it's all flat? I wonder what the term "cluster" should really mean, here? I mean there are surely different types of cores connected, with separate frequency and power domains. So the cpu-map should not be flat, but describe that. Yes, they all use the same MPIDR affinity level, and the manual talks of "cluster0" only, but I wonder if this is not what this node here is about. Looks like the RK3588 also uses the same affinity level for all cores, but has a differentiated cpu-map. > + cluster0 { > + core0 { > + cpu = <&cpu0>; > + }; > + > + core1 { > + cpu = <&cpu1>; > + }; > + > + core2 { > + cpu = <&cpu2>; > + }; > + > + core3 { > + cpu = <&cpu3>; > + }; > + > + core4 { > + cpu = <&cpu4>; > + }; > + > + core5 { > + cpu = <&cpu5>; > + }; > + > + core6 { > + cpu = <&cpu6>; > + }; > + > + core7 { > + cpu = <&cpu7>; > + }; > + }; > + }; > + > + cpu0: cpu@0 { > + compatible = "arm,cortex-a55"; > + device_type = "cpu"; > + reg = <0x0>; > + enable-method = "psci"; > + }; > + > + cpu1: cpu@100 { > + compatible = "arm,cortex-a55"; > + device_type = "cpu"; > + reg = <0x100>; > + enable-method = "psci"; > + }; > + > + cpu2: cpu@200 { > + compatible = "arm,cortex-a55"; > + device_type = "cpu"; > + reg = <0x200>; > + enable-method = "psci"; > + }; > + > + cpu3: cpu@300 { > + compatible = "arm,cortex-a55"; > + device_type = "cpu"; > + reg = <0x300>; > + enable-method = "psci"; > + }; > + > + cpu4: cpu@400 { > + compatible = "arm,cortex-a55"; > + device_type = "cpu"; > + reg = <0x400>; > + enable-method = "psci"; > + }; > + > + cpu5: cpu@500 { > + compatible = "arm,cortex-a55"; > + device_type = "cpu"; > + reg = <0x500>; > + enable-method = "psci"; > + }; > + > + cpu6: cpu@600 { > + compatible = "arm,cortex-a76"; > + device_type = "cpu"; > + reg = <0x600>; > + enable-method = "psci"; > + }; > + > + cpu7: cpu@700 { > + compatible = "arm,cortex-a76"; > + device_type = "cpu"; > + reg = <0x700>; > + enable-method = "psci"; > + }; > + }; > + > + osc: osc-clk { The label should at least "hosc", to differentiate it from the 32KHz crystal. As for the node name: traditionally we put the frequency in there, but that's not really possible if we don't know it yet. So we could as well follow the binding recommendation (to start with "clock-") and use "clock-hosc" or something. I checked the rest of the file thoroughly against their bindings and the manual, all addresses, clocks, and interrupt numbers matched. Cheers, Andre > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + }; > + > + pmu-a55 { > + compatible = "arm,cortex-a55-pmu"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_a55>; > + }; > + > + pmu-a76 { > + compatible = "arm,cortex-a76-pmu"; > + interrupts = <GIC_PPI 7 IRQ_TYPE_LEVEL_HIGH &ppi_a76>; > + }; > + > + psci { > + compatible = "arm,psci-0.2"; > + method = "smc"; > + }; > + > + timer { > + compatible = "arm,armv8-timer"; > + interrupts = <GIC_PPI 13 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_PPI 14 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_PPI 11 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_PPI 10 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_PPI 12 IRQ_TYPE_LEVEL_HIGH 0>; > + arm,no-tick-in-suspend; > + }; > + > + soc@0 { > + compatible = "simple-bus"; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges = <0x0 0x0 0x0 0x40000000>; > + > + pio: pinctrl@2000000 { > + compatible = "allwinner,sun60i-a733-pinctrl"; > + reg = <0x02000000 0x800>; > + interrupts = <GIC_SPI 69 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 71 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 73 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 75 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 77 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 79 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 81 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 83 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 85 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 87 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_APB1>, <&osc>, <&rtc CLK_OSC32K>; > + clock-names = "apb", "hosc", "losc"; > + gpio-controller; > + #gpio-cells = <3>; > + interrupt-controller; > + #interrupt-cells = <3>; > + > + mmc0_pins: mmc0-pins { > + pins = "PF0", "PF1", "PF2", "PF3", "PF4", "PF5"; > + function = "mmc0"; > + allwinner,pinmux = <2>; > + drive-strength = <30>; > + bias-pull-up; > + }; > + > + mmc1_pins: mmc1-pins { > + pins = "PG0", "PG1", "PG2", "PG3", "PG4", "PG5"; > + function = "mmc1"; > + allwinner,pinmux = <2>; > + drive-strength = <30>; > + bias-pull-up; > + }; > + > + mmc2_pins: mmc2-pins { > + pins = "PC5", "PC6", "PC8", "PC9", "PC10", "PC11", > + "PC13", "PC14", "PC15", "PC16"; > + function = "mmc2"; > + allwinner,pinmux = <3>; > + drive-strength = <30>; > + bias-pull-up; > + }; > + > + uart0_pb_pins: uart0-pb-pins { > + pins = "PB9", "PB10"; > + function = "uart0"; > + allwinner,pinmux = <2>; > + }; > + }; > + > + ccu: clock-controller@2002000 { > + compatible = "allwinner,sun60i-a733-ccu"; > + reg = <0x02002000 0x2000>; > + clocks = <&osc>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>, > + <&rtc CLK_OSC32K_FANOUT>; > + clock-names = "hosc", "losc", "iosc", "losc-fanout"; > + #clock-cells = <1>; > + #reset-cells = <1>; > + }; > + > + uart0: serial@2500000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02500000 0x400>; > + interrupts = <GIC_SPI 2 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART0>; > + resets = <&ccu RST_BUS_UART0>; > + status = "disabled"; > + }; > + > + uart1: serial@2501000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02501000 0x400>; > + interrupts = <GIC_SPI 3 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART1>; > + resets = <&ccu RST_BUS_UART1>; > + status = "disabled"; > + }; > + > + uart2: serial@2502000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02502000 0x400>; > + interrupts = <GIC_SPI 4 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART2>; > + resets = <&ccu RST_BUS_UART2>; > + status = "disabled"; > + }; > + > + uart3: serial@2503000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02503000 0x400>; > + interrupts = <GIC_SPI 5 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART3>; > + resets = <&ccu RST_BUS_UART3>; > + status = "disabled"; > + }; > + > + uart4: serial@2504000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02504000 0x400>; > + interrupts = <GIC_SPI 6 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART4>; > + resets = <&ccu RST_BUS_UART4>; > + status = "disabled"; > + }; > + > + uart5: serial@2505000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02505000 0x400>; > + interrupts = <GIC_SPI 7 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART5>; > + resets = <&ccu RST_BUS_UART5>; > + status = "disabled"; > + }; > + > + uart6: serial@2506000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x02506000 0x400>; > + interrupts = <GIC_SPI 8 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&ccu CLK_BUS_UART6>; > + resets = <&ccu RST_BUS_UART6>; > + status = "disabled"; > + }; > + > + i2c0: i2c@2510000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02510000 0x400>; > + interrupts = <GIC_SPI 11 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C0>; > + resets = <&ccu RST_BUS_I2C0>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c1: i2c@2511000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02511000 0x400>; > + interrupts = <GIC_SPI 12 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C1>; > + resets = <&ccu RST_BUS_I2C1>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c2: i2c@2512000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02512000 0x400>; > + interrupts = <GIC_SPI 13 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C2>; > + resets = <&ccu RST_BUS_I2C2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c3: i2c@2513000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02513000 0x400>; > + interrupts = <GIC_SPI 14 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C3>; > + resets = <&ccu RST_BUS_I2C3>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c4: i2c@2514000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02514000 0x400>; > + interrupts = <GIC_SPI 15 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C4>; > + resets = <&ccu RST_BUS_I2C4>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c5: i2c@2515000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02515000 0x400>; > + interrupts = <GIC_SPI 16 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C5>; > + resets = <&ccu RST_BUS_I2C5>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c6: i2c@2516000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02516000 0x400>; > + interrupts = <GIC_SPI 17 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C6>; > + resets = <&ccu RST_BUS_I2C6>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c7: i2c@2517000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02517000 0x400>; > + interrupts = <GIC_SPI 18 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C7>; > + resets = <&ccu RST_BUS_I2C7>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c8: i2c@2518000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02518000 0x400>; > + interrupts = <GIC_SPI 19 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C8>; > + resets = <&ccu RST_BUS_I2C8>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c9: i2c@2519000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x02519000 0x400>; > + interrupts = <GIC_SPI 20 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C9>; > + resets = <&ccu RST_BUS_I2C9>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c10: i2c@251a000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x0251a000 0x400>; > + interrupts = <GIC_SPI 21 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C10>; > + resets = <&ccu RST_BUS_I2C10>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c11: i2c@251b000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x0251b000 0x400>; > + interrupts = <GIC_SPI 22 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C11>; > + resets = <&ccu RST_BUS_I2C11>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + i2c12: i2c@251c000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x0251c000 0x400>; > + interrupts = <GIC_SPI 23 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_I2C12>; > + resets = <&ccu RST_BUS_I2C12>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + gic: interrupt-controller@3400000 { > + compatible = "arm,gic-v3"; > + reg = <0x03400000 0x10000>, <0x03460000 0x100000>; > + interrupts = <GIC_PPI 9 IRQ_TYPE_LEVEL_HIGH 0>; > + dma-noncoherent; > + interrupt-controller; > + #interrupt-cells = <4>; > + #address-cells = <1>; > + #size-cells = <1>; > + ranges; > + > + its: msi-controller@3440000 { > + compatible = "arm,gic-v3-its"; > + reg = <0x03440000 0x20000>; > + msi-controller; > + #msi-cells = <1>; > + dma-noncoherent; > + status = "disabled"; > + }; > + > + ppi-partitions { > + ppi_a55: interrupt-partition-0 { > + affinity = <&cpu0 &cpu1 &cpu2 &cpu3 &cpu4 &cpu5>; > + }; > + > + ppi_a76: interrupt-partition-1 { > + affinity = <&cpu6 &cpu7>; > + }; > + }; > + }; > + > + mmc0: mmc@4020000 { > + compatible = "allwinner,sun60i-a733-mmc", > + "allwinner,sun20i-d1-mmc"; > + reg = <0x04020000 0x1000>; > + interrupts = <GIC_SPI 161 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_MMC0>, <&ccu CLK_MMC0>; > + clock-names = "ahb", "mmc"; > + resets = <&ccu RST_BUS_MMC0>; > + reset-names = "ahb"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc0_pins>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + mmc1: mmc@4021000 { > + compatible = "allwinner,sun60i-a733-mmc", > + "allwinner,sun20i-d1-mmc"; > + reg = <0x04021000 0x1000>; > + interrupts = <GIC_SPI 162 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_MMC1>, <&ccu CLK_MMC1>; > + clock-names = "ahb", "mmc"; > + resets = <&ccu RST_BUS_MMC1>; > + reset-names = "ahb"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc1_pins>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + mmc2: mmc@4022000 { > + compatible = "allwinner,sun60i-a733-mmc", > + "allwinner,sun20i-d1-mmc"; > + reg = <0x04022000 0x1000>; > + interrupts = <GIC_SPI 163 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&ccu CLK_BUS_MMC2>, <&ccu CLK_MMC2>; > + clock-names = "ahb", "mmc"; > + resets = <&ccu RST_BUS_MMC2>; > + reset-names = "ahb"; > + pinctrl-names = "default"; > + pinctrl-0 = <&mmc2_pins>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + r_ccu: clock-controller@7010000 { > + compatible = "allwinner,sun60i-a733-r-ccu"; > + reg = <0x07010000 0x250>; > + clocks = <&osc>, <&rtc CLK_OSC32K>, <&rtc CLK_IOSC>, > + <&ccu CLK_SYS_24M>, <&ccu CLK_PLL_PERIPH0_200M>, > + <&ccu CLK_PLL_PERIPH0_300M>, > + <&ccu CLK_PLL_PERIPH1_300M>; > + clock-names = "hosc", "losc", "iosc", "sys-24m", > + "pll-periph0-200m", "pll-periph0-300m", > + "pll-periph1-300m"; > + #clock-cells = <1>; > + #reset-cells = <1>; > + }; > + > + nmi_intc: interrupt-controller@7010320 { > + compatible = "allwinner,sun60i-a733-nmi", > + "allwinner,sun55i-a523-nmi"; > + reg = <0x07010320 0xc>; > + interrupts = <GIC_SPI 188 IRQ_TYPE_LEVEL_HIGH 0>; > + interrupt-controller; > + #interrupt-cells = <2>; > + }; > + > + r_pio: pinctrl@7025000 { > + compatible = "allwinner,sun60i-a733-r-pinctrl"; > + reg = <0x07025000 0x800>; > + interrupts = <GIC_SPI 198 IRQ_TYPE_LEVEL_HIGH 0>, > + <GIC_SPI 200 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&r_ccu CLK_R_APB0>, <&osc>, <&rtc CLK_OSC32K>; > + clock-names = "apb", "hosc", "losc"; > + gpio-controller; > + #gpio-cells = <3>; > + interrupt-controller; > + #interrupt-cells = <3>; > + > + r_i2c0_pl_pins: r-i2c0-pl-pins { > + pins = "PL0", "PL1"; > + function = "r_i2c0"; > + allwinner,pinmux = <2>; > + }; > + }; > + > + r_uart0: serial@7080000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x07080000 0x400>; > + interrupts = <GIC_SPI 201 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&r_ccu CLK_BUS_R_UART0>; > + resets = <&r_ccu RST_BUS_R_UART0>; > + status = "disabled"; > + }; > + > + r_uart1: serial@7081000 { > + compatible = "allwinner,sun60i-a733-uart", > + "snps,dw-apb-uart"; > + reg = <0x07081000 0x400>; > + interrupts = <GIC_SPI 202 IRQ_TYPE_LEVEL_HIGH 0>; > + reg-shift = <2>; > + reg-io-width = <4>; > + clocks = <&r_ccu CLK_BUS_R_UART1>; > + resets = <&r_ccu RST_BUS_R_UART1>; > + status = "disabled"; > + }; > + > + r_i2c0: i2c@7083000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x07083000 0x400>; > + interrupts = <GIC_SPI 203 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&r_ccu CLK_BUS_R_I2C0>; > + resets = <&r_ccu RST_BUS_R_I2C0>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + r_i2c1: i2c@7084000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x07084000 0x400>; > + interrupts = <GIC_SPI 204 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&r_ccu CLK_BUS_R_I2C1>; > + resets = <&r_ccu RST_BUS_R_I2C1>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + r_i2c2: i2c@7085000 { > + compatible = "allwinner,sun60i-a733-i2c", > + "allwinner,sun8i-v536-i2c", > + "allwinner,sun6i-a31-i2c"; > + reg = <0x07085000 0x400>; > + interrupts = <GIC_SPI 205 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&r_ccu CLK_BUS_R_I2C2>; > + resets = <&r_ccu RST_BUS_R_I2C2>; > + #address-cells = <1>; > + #size-cells = <0>; > + status = "disabled"; > + }; > + > + rtc: rtc@7090000 { > + compatible = "allwinner,sun60i-a733-rtc", > + "allwinner,sun50i-r329-rtc"; > + reg = <0x07090000 0x400>; > + interrupts = <GIC_SPI 196 IRQ_TYPE_LEVEL_HIGH 0>; > + clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc>, <&r_ccu CLK_R_AHB>; > + clock-names = "bus", "hosc", "ahb"; > + #clock-cells = <1>; > + }; > + }; > +}; > ^ permalink raw reply [flat|nested] 7+ messages in thread
* [PATCH v4 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board 2026-11-19 18:09 [PATCH v4 0/3] arm64: dts: allwinner: add A733/Cubie A7S support Enzo Adriano 2026-11-19 18:09 ` [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S Enzo Adriano 2026-11-19 18:09 ` [PATCH v4 2/3] arm64: dts: allwinner: add A733 SoC description Enzo Adriano @ 2026-11-19 18:09 ` Enzo Adriano 2026-11-21 23:39 ` Andre Przywara 2 siblings, 1 reply; 7+ messages in thread From: Enzo Adriano @ 2026-11-19 18:09 UTC (permalink / raw) To: andre.przywara, robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel Cc: Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini, Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid Enable the Cubie A7S serial console, PMIC and microSD slot to provide an initial usable board configuration. Supply the 26 MHz crystal and 32768 Hz RTC input, enable UART0 and the AXP318W on R-I2C0, and describe the PMIC input/output and CPU supply connections from the Radxa Cubie A7S schematic v1.10. Preserve firmware settings on rails whose working voltage is not established. BLDO2 has no programmed voltage constraint: its software 3.3 V selector does not establish its physical output with the schematic's nominal 2.4 V input. Describe the card's SWOUT2 supply and PF6 active-high detect with an internal pull-down. Enable MMC0 at up to 50 MHz using 3.3 V signaling only. Its high-voltage path uses VCCIO; CLDO5 also feeds PC and the PF 1.8 V input and must not be raised for SD signaling. Firmware must select the 3.3 V PF path; dynamic voltage switching is not provided. Keep other storage off. Connect the documented bank supplies. PL's self-supply phandle is omitted to avoid the PMIC/I2C/pinctrl bootstrap cycle, as on the upstream Cubie A5E; ALDO1 is retained always-on. The separate pinctrl voltage-mode fix is required for these bank-supply connections. Signed-off-by: Enzo Adriano <enzo.adriano.code@gmail.com> --- The November 18 v4 RAM boot on Cubie A7S with vendor firmware exercised UART0, PMIC probe and MMC0 read-only transfers. PMIC/NMI interrupt delivery, card writes, physical hotplug, 1.8 V signaling and physical BLDO2 voltage were not tested. arch/arm64/boot/dts/allwinner/Makefile | 1 + .../dts/allwinner/sun60i-a733-cubie-a7s.dts | 287 ++++++++++++++++++ 2 files changed, 288 insertions(+) create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile index da39f02252d4..9d1e740ff19e 100644 --- a/arch/arm64/boot/dts/allwinner/Makefile +++ b/arch/arm64/boot/dts/allwinner/Makefile @@ -69,3 +69,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun55i-a527-cubie-a5e.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtb +dtb-$(CONFIG_ARCH_SUNXI) += sun60i-a733-cubie-a7s.dtb diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts new file mode 100644 index 000000000000..9af9a68950d8 --- /dev/null +++ b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts @@ -0,0 +1,287 @@ +// SPDX-License-Identifier: (GPL-2.0-only OR MIT) +/dts-v1/; + +#include "sun60i-a733.dtsi" + +#include <dt-bindings/gpio/gpio.h> + +/ { + model = "Radxa Cubie A7S"; + compatible = "radxa,cubie-a7s", "allwinner,sun60i-a733"; + + aliases { + mmc0 = &mmc0; + serial0 = &uart0; + }; + + chosen { + stdout-path = "serial0:115200n8"; + }; + + osc32k: osc32k-clk { + compatible = "fixed-clock"; + #clock-cells = <0>; + clock-frequency = <32768>; + }; + + reg_ldo_input: regulator-ldo-input { + compatible = "regulator-fixed"; + regulator-name = "ldo-input"; + /* ETA3521: 0.6 V * (1 + RP298 / RP299), 30k / 10k. */ + regulator-min-microvolt = <2400000>; + regulator-max-microvolt = <2400000>; + regulator-always-on; + vin-supply = <®_ps>; + }; + + reg_ps: regulator-system-power { + compatible = "regulator-fixed"; + regulator-name = "ps"; + regulator-min-microvolt = <5000000>; + regulator-max-microvolt = <5000000>; + regulator-always-on; + }; +}; + +&cpu0 { + cpu-supply = <®_dcdc5>; +}; + +&cpu1 { + cpu-supply = <®_dcdc5>; +}; + +&cpu2 { + cpu-supply = <®_dcdc5>; +}; + +&cpu3 { + cpu-supply = <®_dcdc5>; +}; + +&cpu4 { + cpu-supply = <®_dcdc5>; +}; + +&cpu5 { + cpu-supply = <®_dcdc5>; +}; + +&cpu6 { + cpu-supply = <®_dcdc3>; +}; + +&cpu7 { + cpu-supply = <®_dcdc3>; +}; + +&mmc0 { + bus-width = <4>; + cap-sd-highspeed; + cd-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; + disable-wp; + max-frequency = <50000000>; + no-1-8-v; + vmmc-supply = <®_swout2>; + /* The 3.3 V path uses VCC-IO; no Port F voltage switching yet. */ + vqmmc-supply = <®_swout2>; + + status = "okay"; +}; + +&osc { + clock-frequency = <26000000>; +}; + +&pio { + vcc-pb-supply = <®_swout2>; + vcc-pc-supply = <®_cldo5>; + vcc-pd-supply = <®_swout1>; + vcc-pe-supply = <®_bldo1>; + vcc-pf-supply = <®_cldo5>; + vcc-pg-supply = <®_aldo1>; + vcc-ph-supply = <®_swout2>; + vcc-pj-supply = <®_swout1>; + vcc-pk-supply = <®_bldo1>; +}; + +&r_i2c0 { + pinctrl-names = "default"; + pinctrl-0 = <&r_i2c0_pl_pins>; + + status = "okay"; + + axp318w: pmic@36 { + compatible = "x-powers,axp318w"; + reg = <0x36>; + interrupt-parent = <&nmi_intc>; + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; + interrupt-controller; + #interrupt-cells = <1>; + + aldo156in-supply = <®_ps>; + aldo234in-supply = <®_aldo1>; + bldoin-supply = <®_ldo_input>; + cldoin-supply = <®_ldo_input>; + dldoin-supply = <®_ps>; + eldoin-supply = <®_dcdc9>; + ips-supply = <®_ps>; + vin19-supply = <®_ps>; + vin23-supply = <®_ps>; + vin45-supply = <®_ps>; + vin678-supply = <®_ps>; + + regulators { + reg_dcdc1: dcdc1 { + regulator-name = "vcc-3v3"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_dcdc2: dcdc2 { + regulator-name = "vdd-sys"; + regulator-always-on; + }; + + reg_dcdc3: dcdc3 { + regulator-name = "vdd-cpub"; + regulator-always-on; + }; + + reg_dcdc4: dcdc4 { + regulator-name = "vdd-gpu"; + regulator-always-on; + }; + + reg_dcdc5: dcdc5 { + regulator-name = "vdd-cpul"; + regulator-always-on; + }; + + reg_dcdc6: dcdc6 { + regulator-name = "vcc-draml"; + regulator-always-on; + }; + + reg_dcdc7: dcdc7 { + regulator-name = "vcc-dram"; + regulator-always-on; + }; + + reg_dcdc8: dcdc8 { + regulator-name = "vcc-ufs-io"; + regulator-always-on; + }; + + reg_dcdc9: dcdc9 { + regulator-name = "eldo-input"; + regulator-always-on; + }; + + reg_swout1: swout1 { + regulator-name = "vcc33-lcd"; + regulator-always-on; + }; + + reg_swout2: swout2 { + regulator-name = "vcc-io-card"; + regulator-always-on; + }; + + reg_aldo1: aldo1 { + regulator-name = "vcc-pl"; + regulator-min-microvolt = <3300000>; + regulator-max-microvolt = <3300000>; + regulator-always-on; + }; + + reg_bldo1: bldo1 { + regulator-name = "vcc-pe-pk-mcsi"; + }; + + reg_bldo2: bldo2 { + regulator-name = "vcc-lvds0"; + regulator-always-on; + }; + + reg_bldo4: bldo4 { + regulator-name = "vcc18-codec"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_cldo1: cldo1 { + regulator-name = "vcc33-18-usb"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_cldo2: cldo2 { + regulator-name = "vcc18-hdmi"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + }; + + reg_cldo3: cldo3 { + regulator-name = "vcc-pll-dram"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_cldo5: cldo5 { + regulator-name = "vcc18-pf-pc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + + reg_dldo1: dldo1 { + regulator-name = "vcc-efuse"; + regulator-always-on; + }; + + reg_dldo6: dldo6 { + regulator-name = "vcc-ufs"; + regulator-always-on; + }; + + reg_eldo1: eldo1 { + regulator-name = "vcc09-vdd2l"; + regulator-always-on; + }; + + reg_eldo6: eldo6 { + regulator-name = "vdd-cpus"; + regulator-always-on; + }; + + reg_rtc_ldo: rtc-ldo { + regulator-name = "vcc-rtc"; + regulator-min-microvolt = <1800000>; + regulator-max-microvolt = <1800000>; + regulator-always-on; + }; + }; + }; +}; + +&r_pio { + /* PL powers the PMIC bus itself; firmware must keep ALDO1 enabled. */ + vcc-pm-supply = <®_aldo1>; +}; + +&rtc { + clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc>, <&r_ccu CLK_R_AHB>, + <&osc32k>; + clock-names = "bus", "hosc", "ahb", "ext-osc32k"; +}; + +&uart0 { + pinctrl-names = "default"; + pinctrl-0 = <&uart0_pb_pins>; + + status = "okay"; +}; ^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: [PATCH v4 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board 2026-11-19 18:09 ` [PATCH v4 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board Enzo Adriano @ 2026-11-21 23:39 ` Andre Przywara 0 siblings, 0 replies; 7+ messages in thread From: Andre Przywara @ 2026-11-21 23:39 UTC (permalink / raw) To: Enzo Adriano Cc: robh, krzk+dt, conor+dt, wens, jernej.skrabec, samuel, Maxime Ripard, devicetree, linux-arm-kernel, linux-sunxi, linux-kernel, Junhui Liu, Jerome Brunet, Pablo Mazzini, Vinicius Pedrosa, Alexander Sverdlin, Jun Yan, Lukas Schmid On Thu, 19 Nov 2026 13:09:26 -0500 Enzo Adriano <enzo.adriano.code@gmail.com> wrote: Hi Enzo, > Enable the Cubie A7S serial console, PMIC and microSD slot to provide > an initial usable board configuration. Supply the 26 MHz crystal and > 32768 Hz RTC input, enable UART0 and the AXP318W on R-I2C0, and describe > the PMIC input/output and CPU supply connections from the Radxa Cubie > A7S schematic v1.10. Preserve firmware settings on rails whose working > voltage is not established. BLDO2 has no programmed voltage constraint: > its software 3.3 V selector does not establish its physical output with > the schematic's nominal 2.4 V input. > > Describe the card's SWOUT2 supply and PF6 active-high detect with an > internal pull-down. Enable MMC0 at up to 50 MHz using 3.3 V signaling > only. Its high-voltage path uses VCCIO; CLDO5 also feeds PC and the PF > 1.8 V input and must not be raised for SD signaling. Firmware must > select the 3.3 V PF path; dynamic voltage switching is not provided. > Keep other storage off. > > Connect the documented bank supplies. PL's self-supply phandle is > omitted to avoid the PMIC/I2C/pinctrl bootstrap cycle, as on the > upstream Cubie A5E; ALDO1 is retained always-on. The separate pinctrl > voltage-mode fix is required for these bank-supply connections. > > Signed-off-by: Enzo Adriano <enzo.adriano.code@gmail.com> > --- > > The November 18 v4 RAM boot on Cubie A7S with vendor firmware exercised > UART0, PMIC probe and MMC0 read-only transfers. PMIC/NMI interrupt > delivery, card writes, physical hotplug, 1.8 V signaling and physical > BLDO2 voltage were not tested. > > arch/arm64/boot/dts/allwinner/Makefile | 1 + > .../dts/allwinner/sun60i-a733-cubie-a7s.dts | 287 ++++++++++++++++++ > 2 files changed, 288 insertions(+) > create mode 100644 arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts > > diff --git a/arch/arm64/boot/dts/allwinner/Makefile b/arch/arm64/boot/dts/allwinner/Makefile > index da39f02252d4..9d1e740ff19e 100644 > --- a/arch/arm64/boot/dts/allwinner/Makefile > +++ b/arch/arm64/boot/dts/allwinner/Makefile > @@ -69,3 +69,4 @@ dtb-$(CONFIG_ARCH_SUNXI) += sun55i-a527-cubie-a5e.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun55i-h728-x96qpro+.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-avaota-a1.dtb > dtb-$(CONFIG_ARCH_SUNXI) += sun55i-t527-orangepi-4a.dtb > +dtb-$(CONFIG_ARCH_SUNXI) += sun60i-a733-cubie-a7s.dtb > diff --git a/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts > new file mode 100644 > index 000000000000..9af9a68950d8 > --- /dev/null > +++ b/arch/arm64/boot/dts/allwinner/sun60i-a733-cubie-a7s.dts > @@ -0,0 +1,287 @@ > +// SPDX-License-Identifier: (GPL-2.0-only OR MIT) > +/dts-v1/; > + > +#include "sun60i-a733.dtsi" > + > +#include <dt-bindings/gpio/gpio.h> > + > +/ { > + model = "Radxa Cubie A7S"; > + compatible = "radxa,cubie-a7s", "allwinner,sun60i-a733"; > + > + aliases { > + mmc0 = &mmc0; We don't do mmc aliases. Long discussion, I understand it seems useful, but relying on Linux device numbering is not a good idea. So please drop this line. U-Boot will give it back to you if you use the U-Boot devicetree ($fdtcontroladdr). > + serial0 = &uart0; > + }; > + > + chosen { > + stdout-path = "serial0:115200n8"; > + }; > + > + osc32k: osc32k-clk { > + compatible = "fixed-clock"; > + #clock-cells = <0>; > + clock-frequency = <32768>; > + }; > + > + reg_ldo_input: regulator-ldo-input { I think the node name alone is slightly misleading: it's indeed supplying some LDO input rails on the PMIC, but the chip itself is a DC/DC step down converter. Please add a comment here like this: /* discrete ETA3521 DC/DC step-down regulator */ And maybe use "regulator-2v4" as the node name (to match the binding requirement), the regulator name can then carry the usage meaning. > + compatible = "regulator-fixed"; > + regulator-name = "ldo-input"; > + /* ETA3521: 0.6 V * (1 + RP298 / RP299), 30k / 10k. */ > + regulator-min-microvolt = <2400000>; > + regulator-max-microvolt = <2400000>; > + regulator-always-on; > + vin-supply = <®_ps>; > + }; > + > + reg_ps: regulator-system-power { Please add a comment here, saying: /* board wide 5V supply from the USB-C connector */ And then change the node name to "regulator-5v". Also please move this whole node first, as this is the root of the whole power tree. > + compatible = "regulator-fixed"; > + regulator-name = "ps"; > + regulator-min-microvolt = <5000000>; > + regulator-max-microvolt = <5000000>; > + regulator-always-on; > + }; There are two LEDs on the last page of the schematic, controlled by PJ26 and PM2. Please add them here. Check other (Allwinner) DTs for how to do that. > +}; > + > +&cpu0 { > + cpu-supply = <®_dcdc5>; > +}; > + > +&cpu1 { > + cpu-supply = <®_dcdc5>; > +}; > + > +&cpu2 { > + cpu-supply = <®_dcdc5>; > +}; > + > +&cpu3 { > + cpu-supply = <®_dcdc5>; > +}; > + > +&cpu4 { > + cpu-supply = <®_dcdc5>; > +}; > + > +&cpu5 { > + cpu-supply = <®_dcdc5>; > +}; > + > +&cpu6 { > + cpu-supply = <®_dcdc3>; > +}; > + > +&cpu7 { > + cpu-supply = <®_dcdc3>; > +}; > + The schematic shows an EEPROM on I2C0. There is a binding for that chip already, check rk3576-rock-4d.dts. Please add that chip. > +&mmc0 { > + bus-width = <4>; > + cap-sd-highspeed; I think we want the other two standard capabilities as well: cap-mmc-highspeed; cap-sdio-irq; > + cd-gpios = <&pio 5 6 (GPIO_ACTIVE_HIGH | GPIO_PULL_DOWN)>; > + disable-wp; > + max-frequency = <50000000>; Where does this limit come from? As it stands right now, at 3.3V you won't get faster anyway, so it's moot. Please remove if you agree. > + no-1-8-v; > + vmmc-supply = <®_swout2>; > + /* The 3.3 V path uses VCC-IO; no Port F voltage switching yet. */ > + vqmmc-supply = <®_swout2>; Just leave that out (for now), the default is to revert to vmmc-supply, if vqmmc is not given anyway. > + > + status = "okay"; > +}; > + > +&osc { > + clock-frequency = <26000000>; > +}; > + > +&pio { > + vcc-pb-supply = <®_swout2>; Please add a comment that this comes via VCC-IO, see the A527/T527 boards. > + vcc-pc-supply = <®_cldo5>; > + vcc-pd-supply = <®_swout1>; > + vcc-pe-supply = <®_bldo1>; > + vcc-pf-supply = <®_cldo5>; Same here, comment about this being VCC-IO, at least for now. > + vcc-pg-supply = <®_aldo1>; > + vcc-ph-supply = <®_swout2>; > + vcc-pj-supply = <®_swout1>; > + vcc-pk-supply = <®_bldo1>; > +}; > + > +&r_i2c0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&r_i2c0_pl_pins>; > + > + status = "okay"; > + > + axp318w: pmic@36 { > + compatible = "x-powers,axp318w"; > + reg = <0x36>; > + interrupt-parent = <&nmi_intc>; > + interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > + interrupt-controller; > + #interrupt-cells = <1>; > + > + aldo156in-supply = <®_ps>; > + aldo234in-supply = <®_aldo1>; > + bldoin-supply = <®_ldo_input>; > + cldoin-supply = <®_ldo_input>; > + dldoin-supply = <®_ps>; > + eldoin-supply = <®_dcdc9>; > + ips-supply = <®_ps>; > + vin19-supply = <®_ps>; > + vin23-supply = <®_ps>; > + vin45-supply = <®_ps>; > + vin678-supply = <®_ps>; > + > + regulators { > + reg_dcdc1: dcdc1 { > + regulator-name = "vcc-3v3"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; Please add a comment or use a speaking regulator name to justify that this regulator must be always on. "regulator-always-on" should be the exception, not the rule. This applies to all the nodes below, I will comment with some hints below again. > + }; > + > + reg_dcdc2: dcdc2 { > + regulator-name = "vdd-sys"; > + regulator-always-on; We should have a voltage or a range for every regulator. Here it should be 0.8V. > + }; > + > + reg_dcdc3: dcdc3 { > + regulator-name = "vdd-cpub"; Do we have some OPPs for the cores? The range should reflect the min/max used voltages in there. > + regulator-always-on; > + }; > + > + reg_dcdc4: dcdc4 { > + regulator-name = "vdd-gpu"; > + regulator-always-on; Why is this always on? If I see this correctly, that's just supplying the GPU, which will have its own supply property. Voltages should be in the same range as for the CPUs. > + }; > + > + reg_dcdc5: dcdc5 { > + regulator-name = "vdd-cpul"; > + regulator-always-on; > + }; > + > + reg_dcdc6: dcdc6 { > + regulator-name = "vcc-draml"; > + regulator-always-on; 0.6/0.5V I guess. > + }; > + > + reg_dcdc7: dcdc7 { > + regulator-name = "vcc-dram"; > + regulator-always-on; Probably 1.1V. > + }; > + > + reg_dcdc8: dcdc8 { > + regulator-name = "vcc-ufs-io"; > + regulator-always-on; > + }; But there is no UFS on this board, right? All the UFS signals seem to be not-connected, so this power supply will be going nowhere. And DCDC8 seems to be used exclusively for UFS, so I would just leave this whole node out. > + > + reg_dcdc9: dcdc9 { > + regulator-name = "eldo-input"; > + regulator-always-on; Again, why the always-on? This is referenced by eldoin-supply, so the kernel should keep this on. As for the voltage, the schematic doesn't seem to give a clue, so maybe you can look this up on a running BSP kernel. > + }; > + > + reg_swout1: swout1 { > + regulator-name = "vcc33-lcd"; > + regulator-always-on; > + }; Why always-on? Should be referenced by the pinctrl device. > + > + reg_swout2: swout2 { > + regulator-name = "vcc-io-card"; > + regulator-always-on; > + }; > + > + reg_aldo1: aldo1 { > + regulator-name = "vcc-pl"; > + regulator-min-microvolt = <3300000>; > + regulator-max-microvolt = <3300000>; > + regulator-always-on; > + }; > + > + reg_bldo1: bldo1 { > + regulator-name = "vcc-pe-pk-mcsi"; Does this intentionally miss the voltage setting? The datasheets suggests that VCC-MCSI must be 1.8V. > + }; > + > + reg_bldo2: bldo2 { > + regulator-name = "vcc-lvds0"; > + regulator-always-on; Should not be needed. And again, the voltage is missing. Per the datasheet, VCC_LVDS0 must be 1.8V, and the VCC18-LCD label connected to BLDO2 supports this. > + }; > + > + reg_bldo4: bldo4 { > + regulator-name = "vcc18-codec"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; Do we need this at all? I don't see this (VCC18-CODEC) connected anywhere? > + > + reg_cldo1: cldo1 { > + regulator-name = "vcc33-18-usb"; That's not the right name. The connection between VCC33-18-USB and CLDO1 is "NC" in the schematic, so this is a red herring. However this also connects to VDD18-LPDDR, which would justify the always-on. > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + reg_cldo2: cldo2 { > + regulator-name = "vcc18-hdmi"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + }; > + > + reg_cldo3: cldo3 { > + regulator-name = "vcc-pll-dram"; This is a correct example, btw: it's always on, but the regulator name makes it almost obvious why. > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + > + reg_cldo5: cldo5 { > + regulator-name = "vcc18-pf-pc"; VCC18-PF is confusing, please remove that from the name. > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; Should not be needed. Voltage is missing, should be 1.8V, I think. Please try to double check on a system running with the BSP kernel. > + }; > + > + reg_dldo1: dldo1 { > + regulator-name = "vcc-efuse"; > + regulator-always-on; Voltage is missing, should be 1.8V, I think. Please try to double check on a system running with the BSP kernel. > + }; > + > + reg_dldo6: dldo6 { > + regulator-name = "vcc-ufs"; > + regulator-always-on; Apparently UFS is not supported on that board, so please remove that node. > + }; > + > + reg_eldo1: eldo1 { > + regulator-name = "vcc09-vdd2l"; > + regulator-always-on; Voltage should be 0.9V. > + }; > + > + reg_eldo6: eldo6 { > + regulator-name = "vdd-cpus"; > + regulator-always-on; Schematics suggest 0.8V. Cheers, Andre > + }; > + > + reg_rtc_ldo: rtc-ldo { > + regulator-name = "vcc-rtc"; > + regulator-min-microvolt = <1800000>; > + regulator-max-microvolt = <1800000>; > + regulator-always-on; > + }; > + }; > + }; > +}; > + > +&r_pio { > + /* PL powers the PMIC bus itself; firmware must keep ALDO1 enabled. */ > + vcc-pm-supply = <®_aldo1>; > +}; > + > +&rtc { > + clocks = <&r_ccu CLK_BUS_R_RTC>, <&osc>, <&r_ccu CLK_R_AHB>, > + <&osc32k>; > + clock-names = "bus", "hosc", "ahb", "ext-osc32k"; > +}; > + > +&uart0 { > + pinctrl-names = "default"; > + pinctrl-0 = <&uart0_pb_pins>; > + > + status = "okay"; > +}; > ^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2026-11-21 23:40 UTC | newest] Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2026-11-19 18:09 [PATCH v4 0/3] arm64: dts: allwinner: add A733/Cubie A7S support Enzo Adriano 2026-11-19 18:09 ` [PATCH v4 1/3] dt-bindings: arm: sunxi: document Radxa Cubie A7S Enzo Adriano 2026-11-21 23:40 ` Andre Przywara 2026-11-19 18:09 ` [PATCH v4 2/3] arm64: dts: allwinner: add A733 SoC description Enzo Adriano 2026-11-21 10:23 ` Andre Przywara 2026-11-19 18:09 ` [PATCH v4 3/3] arm64: dts: allwinner: add Radxa Cubie A7S board Enzo Adriano 2026-11-21 23:39 ` Andre Przywara
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®