From: Komal Bajaj <quic_kbajaj@quicinc.com>
To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Andy Gross <agross@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konrad.dybcio@linaro.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
<linux-arm-msm@vger.kernel.org>, <devicetree@vger.kernel.org>,
<linux-kernel@vger.kernel.org>
Subject: Re: [PATCH v5 2/3] arm64: dts: qcom: Add base qcm6490 idp board dts
Date: Thu, 23 Nov 2023 19:36:17 +0530 [thread overview]
Message-ID: <3d8a8943-af70-c291-d2d8-41067d8404f2@quicinc.com> (raw)
In-Reply-To: <CAA8EJpo1PvOf4UQiL2Va1ykC0M4zvp1m=iFEVFH5aw4r-TGKxA@mail.gmail.com>
Please ignore if received twice.
On 11/20/2023 8:24 PM, Dmitry Baryshkov wrote:
> On Mon, 20 Nov 2023 at 15:48, Komal Bajaj <quic_kbajaj@quicinc.com> wrote:
>>
>> Add DTS for Qualcomm IDP platform using QCM6490 SoC.
>> This adds debug uart, eMMC and usb support along with
>> regulators found on this board.
>>
>> Signed-off-by: Komal Bajaj <quic_kbajaj@quicinc.com>
>> Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>
>> ---
>> arch/arm64/boot/dts/qcom/Makefile | 1 +
>> arch/arm64/boot/dts/qcom/qcm6490-idp.dts | 422 +++++++++++++++++++++++
>> 2 files changed, 423 insertions(+)
>> create mode 100644 arch/arm64/boot/dts/qcom/qcm6490-idp.dts
>>
>> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
>> index d6cb840b7050..77babebe4904 100644
>> --- a/arch/arm64/boot/dts/qcom/Makefile
>> +++ b/arch/arm64/boot/dts/qcom/Makefile
>> @@ -87,6 +87,7 @@ dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-maple.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += msm8998-sony-xperia-yoshino-poplar.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += msm8998-xiaomi-sagit.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcm6490-fairphone-fp5.dtb
>> +dtb-$(CONFIG_ARCH_QCOM) += qcm6490-idp.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-1000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qcs404-evb-4000.dtb
>> dtb-$(CONFIG_ARCH_QCOM) += qdu1000-idp.dtb
>> diff --git a/arch/arm64/boot/dts/qcom/qcm6490-idp.dts b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
>> new file mode 100644
>> index 000000000000..5b771827d634
>> --- /dev/null
>> +++ b/arch/arm64/boot/dts/qcom/qcm6490-idp.dts
>> @@ -0,0 +1,422 @@
>> +// SPDX-License-Identifier: BSD-3-Clause
>> +/*
>> + * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
>> + */
>> +
>> +/dts-v1/;
>> +
>> +#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>> +#include "sc7280.dtsi"
>> +#include "pm7325.dtsi"
>> +#include "pm8350c.dtsi"
>> +#include "pmk8350.dtsi"
>> +
>> +/delete-node/ &ipa_fw_mem;
>> +/delete-node/ &rmtfs_mem;
>> +/delete-node/ &video_mem;
>> +/delete-node/ &wlan_ce_mem;
>> +/delete-node/ &xbl_mem;
>> +
>> +/ {
>> + model = "Qualcomm Technologies, Inc. QCM6490 IDP";
>> + compatible = "qcom,qcm6490-idp", "qcom,qcm6490";
>> +
>> + aliases {
>> + serial0 = &uart5;
>> + };
>> +
>> + chosen {
>> + stdout-path = "serial0:115200n8";
>> + };
>
> Is there a regulator-vph-pwr somewhere?
Will add it.
>
>> +
>> + reserved-memory {
>> + xbl_mem: xbl@80700000 {
>> + reg = <0x0 0x80700000 0x0 0x100000>;
>> + no-map;
>> + };
>> +
>> + cdsp_secure_heap_mem: cdsp-secure-heap@81800000 {
>> + reg = <0x0 0x81800000 0x0 0x1e00000>;
>> + no-map;
>> + };
>> +
>> + camera_mem: camera@84300000 {
>> + reg = <0x0 0x84300000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + wpss_mem: wpss@84800000 {
>> + reg = <0x0 0x84800000 0x0 0x1900000>;
>> + no-map;
>> + };
>> +
>> + adsp_mem: adsp@86100000 {
>> + reg = <0x0 0x86100000 0x0 0x2800000>;
>> + no-map;
>> + };
>> +
>> + cdsp_mem: cdsp@88900000 {
>> + reg = <0x0 0x88900000 0x0 0x1e00000>;
>> + no-map;
>> + };
>> +
>> + video_mem: video@8a700000 {
>> + reg = <0x0 0x8a700000 0x0 0x700000>;
>> + no-map;
>> + };
>> +
>> + cvp_mem: cvp@8ae00000 {
>> + reg = <0x0 0x8ae00000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + ipa_fw_mem: ipa-fw@8b300000 {
>> + reg = <0x0 0x8b300000 0x0 0x10000>;
>> + no-map;
>> + };
>> +
>> + ipa_gsi_mem: ipa-gsi@8b310000 {
>> + reg = <0x0 0x8b310000 0x0 0xa000>;
>> + no-map;
>> + };
>> +
>> + gpu_microcode_mem: gpu-microcode@8b31a000 {
>> + reg = <0x0 0x8b31a000 0x0 0x2000>;
>> + no-map;
>> + };
>> +
>> + mpss_mem: mpss@8b800000 {
>> + reg = <0x0 0x8b800000 0x0 0xf600000>;
>> + no-map;
>> + };
>> +
>> + tz_stat_mem: tz-stat@c0000000 {
>> + reg = <0x0 0xc0000000 0x0 0x100000>;
>> + no-map;
>> + };
>> +
>> + tags_mem: tags@c0100000 {
>> + reg = <0x0 0xc0100000 0x0 0x1200000>;
>> + no-map;
>> + };
>> +
>> + qtee_mem: qtee@c1300000 {
>> + reg = <0x0 0xc1300000 0x0 0x500000>;
>> + no-map;
>> + };
>> +
>> + trusted_apps_mem: trusted_apps@c1800000 {
>> + reg = <0x0 0xc1800000 0x0 0x1c00000>;
>> + no-map;
>> + };
>> +
>> + debug_vm_mem: debug-vm@d0600000 {
>> + reg = <0x0 0xd0600000 0x0 0x100000>;
>> + no-map;
>> + };
>
> I thought it was proposed to keep the memory map in qcm6490.dtsi. Was
> I mistaken or was this proposal declined?
Considering yours and other comment about the DT describes the hardware,
the only common thing between these boards will be memory map in
qcm6490.dtsi and at this moment it does not seem fine to have
qcm6490.dtsi just for memory map however, we can always comeback in the
future if there are more other common things between these IOT family
platforms.
>
>> + };
>> +};
>> +
>> +&apps_rsc {
>> + regulators-0 {
>> + compatible = "qcom,pm7325-rpmh-regulators";
>> + qcom,pmic-id = "b";
>
> No supplies for any of the regulators?
Sure, will add it.
>
>> +
>> + vreg_s1b_1p872: smps1 {
>> + regulator-min-microvolt = <1840000>;
>> + regulator-max-microvolt = <2040000>;
>> + };
>> +
>> + vreg_s2b_0p876: smps2 {
>> + regulator-min-microvolt = <570070>;
>> + regulator-max-microvolt = <1050000>;
>> + };
>> +
>> + vreg_s7b_0p972: smps7 {
>> + regulator-min-microvolt = <535000>;
>> + regulator-max-microvolt = <1120000>;
>> + };
>> +
>> + vreg_s8b_1p272: smps8 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1500000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_RET>;
>> + };
>> +
>> + vreg_l1b_0p912: ldo1 {
>> + regulator-min-microvolt = <825000>;
>> + regulator-max-microvolt = <925000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l2b_3p072: ldo2 {
>> + regulator-min-microvolt = <2700000>;
>> + regulator-max-microvolt = <3544000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l3b_0p504: ldo3 {
>> + regulator-min-microvolt = <312000>;
>> + regulator-max-microvolt = <910000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l4b_0p752: ldo4 {
>> + regulator-min-microvolt = <752000>;
>> + regulator-max-microvolt = <820000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + reg_l5b_0p752: ldo5 {
>> + regulator-min-microvolt = <552000>;
>> + regulator-max-microvolt = <832000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l6b_1p2: ldo6 {
>> + regulator-min-microvolt = <1140000>;
>> + regulator-max-microvolt = <1260000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l7b_2p952: ldo7 {
>> + regulator-min-microvolt = <2400000>;
>> + regulator-max-microvolt = <3544000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l8b_0p904: ldo8 {
>> + regulator-min-microvolt = <870000>;
>> + regulator-max-microvolt = <970000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l9b_1p2: ldo9 {
>> + regulator-min-microvolt = <1200000>;
>> + regulator-max-microvolt = <1304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l11b_1p504: ldo11 {
>> + regulator-min-microvolt = <1504000>;
>> + regulator-max-microvolt = <2000000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l12b_0p751: ldo12 {
>> + regulator-min-microvolt = <751000>;
>> + regulator-max-microvolt = <824000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l13b_0p53: ldo13 {
>> + regulator-min-microvolt = <530000>;
>> + regulator-max-microvolt = <824000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l14b_1p08: ldo14 {
>> + regulator-min-microvolt = <1080000>;
>> + regulator-max-microvolt = <1304000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l15b_0p765: ldo15 {
>> + regulator-min-microvolt = <765000>;
>> + regulator-max-microvolt = <1020000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l16b_1p1: ldo16 {
>> + regulator-min-microvolt = <1100000>;
>> + regulator-max-microvolt = <1300000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l17b_1p7: ldo17 {
>> + regulator-min-microvolt = <1700000>;
>> + regulator-max-microvolt = <1900000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l18b_1p8: ldo18 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <2000000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l19b_1p8: ldo19 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <2000000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + regulator-allow-set-load;
>> + regulator-allowed-modes = <RPMH_REGULATOR_MODE_LPM
>> + RPMH_REGULATOR_MODE_HPM>;
>> + };
>> + };
>> +
>> + regulators-1 {
>> + compatible = "qcom,pm8350c-rpmh-regulators";
>> + qcom,pmic-id = "c";
>> +
>> + vreg_s1c_2p19: smps1 {
>> + regulator-min-microvolt = <2190000>;
>> + regulator-max-microvolt = <2210000>;
>> + };
>> +
>> + vreg_s2c_0p752: smps2 {
>> + regulator-min-microvolt = <750000>;
>> + regulator-max-microvolt = <800000>;
>> + };
>> +
>> + vreg_s5c_0p752: smps5 {
>> + regulator-min-microvolt = <465000>;
>> + regulator-max-microvolt = <1050000>;
>> + };
>> +
>> + vreg_s7c_0p752: smps7 {
>> + regulator-min-microvolt = <465000>;
>> + regulator-max-microvolt = <800000>;
>> + };
>> +
>> + vreg_s9c_1p084: smps9 {
>> + regulator-min-microvolt = <1010000>;
>> + regulator-max-microvolt = <1170000>;
>> + };
>> +
>> + vreg_l1c_1p8: ldo1 {
>> + regulator-min-microvolt = <1800000>;
>> + regulator-max-microvolt = <1980000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l2c_1p62: ldo2 {
>> + regulator-min-microvolt = <1620000>;
>> + regulator-max-microvolt = <1980000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l3c_2p8: ldo3 {
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <3540000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l4c_1p62: ldo4 {
>> + regulator-min-microvolt = <1620000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l5c_1p62: ldo5 {
>> + regulator-min-microvolt = <1620000>;
>> + regulator-max-microvolt = <3300000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l6c_2p96: ldo6 {
>> + regulator-min-microvolt = <1650000>;
>> + regulator-max-microvolt = <3544000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l7c_3p0: ldo7 {
>> + regulator-min-microvolt = <3000000>;
>> + regulator-max-microvolt = <3544000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l8c_1p62: ldo8 {
>> + regulator-min-microvolt = <1620000>;
>> + regulator-max-microvolt = <2000000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l9c_2p96: ldo9 {
>> + regulator-min-microvolt = <2700000>;
>> + regulator-max-microvolt = <35440000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l10c_0p88: ldo10 {
>> + regulator-min-microvolt = <720000>;
>> + regulator-max-microvolt = <1050000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l11c_2p8: ldo11 {
>> + regulator-min-microvolt = <2800000>;
>> + regulator-max-microvolt = <3544000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l12c_1p65: ldo12 {
>> + regulator-min-microvolt = <1650000>;
>> + regulator-max-microvolt = <2000000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_l13c_2p7: ldo13 {
>> + regulator-min-microvolt = <2700000>;
>> + regulator-max-microvolt = <3544000>;
>> + regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
>> + };
>> +
>> + vreg_bob_3p296: bob {
>> + regulator-min-microvolt = <3008000>;
>> + regulator-max-microvolt = <3960000>;
>> + };
>> + };
>> +};
>> +
>> +&qupv3_id_0 {
>> + status = "okay";
>> +};
>> +
>> +&sdhc_1 {
>> + non-removable;
>> + no-sd;
>> + no-sdio;
>> +
>> + vmmc-supply = <&vreg_l7b_2p952>;
>> + vqmmc-supply = <&vreg_l19b_1p8>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&tlmm {
>> + gpio-reserved-ranges = <32 2>, /* ADSP */
>> + <48 4>; /* NFC */
>> +};
>> +
>> +&uart5 {
>> + compatible = "qcom,geni-debug-uart";
>> + status = "okay";
>> +};
>> +
>> +&usb_1 {
>> + status = "okay";
>> +};
>> +
>> +&usb_1_dwc3 {
>> + dr_mode = "peripheral";
>
> Just out of curiosity, what controls the OTG here? Is it the
> PMIC-GLINK / UCSI or is it the raw TCPM using the PMIC?
PMIC_GLINK.
Currently there is no support for glink for this soc, that's why
going ahead with peripheral mode.
>
>> +};
>> +
>> +&usb_1_hsphy {
>> + vdda-pll-supply = <&vreg_l10c_0p88>;
>> + vdda33-supply = <&vreg_l2b_3p072>;
>> + vdda18-supply = <&vreg_l1c_1p8>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&usb_1_qmpphy {
>> + vdda-phy-supply = <&vreg_l6b_1p2>;
>> + vdda-pll-supply = <&vreg_l1b_0p912>;
>> +
>> + status = "okay";
>> +};
>> +
>> +&wifi {
>> + memory-region = <&wlan_fw_mem>;
>
> Does that work without the CE region? SC7280 lists one.
Only chrome has this requirement that's why it lists there.
Thanks
Komal
>
>> +};
>> --
>> 2.42.0
>>
>>
>
>
next prev parent reply other threads:[~2023-11-23 14:06 UTC|newest]
Thread overview: 10+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-11-20 13:47 [PATCH v5 0/3] Add support for qcm6490 idp and qcs6490 rb3gen2 board Komal Bajaj
2023-11-20 13:47 ` [PATCH v5 1/3] dt-bindings: arm: qcom: Add QCM6490 IDP and QCS6490 RB3Gen2 board Komal Bajaj
2023-11-20 13:47 ` [PATCH v5 2/3] arm64: dts: qcom: Add base qcm6490 idp board dts Komal Bajaj
2023-11-20 14:54 ` Dmitry Baryshkov
2023-11-23 14:06 ` Komal Bajaj [this message]
2023-11-20 13:47 ` [PATCH v5 3/3] arm64: dts: qcom: Add base qcs6490-rb3gen2 " Komal Bajaj
2023-11-20 14:47 ` Caleb Connolly
2023-11-23 14:16 ` Komal Bajaj
2023-11-20 14:58 ` Dmitry Baryshkov
2023-11-23 14:18 ` Komal Bajaj
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=3d8a8943-af70-c291-d2d8-41067d8404f2@quicinc.com \
--to=quic_kbajaj@quicinc.com \
--cc=agross@kernel.org \
--cc=andersson@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=konrad.dybcio@linaro.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=robh+dt@kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®