From: Art Tevs <arti_tevs@yahoo.de>
To: linux-kernel@vger.kernel.org
Subject: PROBLEM:
Date: Thu, 19 Feb 2004 15:53:37 +0100 [thread overview]
Message-ID: <4034CDF1.4090405@yahoo.de> (raw)
1. Initialisation of hda failes.
2. The compiled 2.6.3 (or 2.6.3-rc3 too) cannnot initialize hda.
Report from hdaprm of my drive:
Model=FUJITSU MHS2020AT, FwRev=8004, SerialNo=NL42T3113SKH
Config={ HardSect NotMFM HdSw>15uSec Fixed DTR>10Mbs }
RawCHS=16383/16/63, TrkSize=0, SectSize=0, ECCbytes=4
BuffType=DualPortCache, BuffSize=2048kB, MaxMultSect=16, MultSect=16
CurCHS=16383/16/63, CurSects=16514064, LBA=yes, LBAsects=39070080
IORDY=yes, tPIO={min:240,w/IORDY:120}, tDMA={min:120,rec:120}
PIO modes: pio0 pio1 pio2 pio3 pio4
DMA modes: mdma0 mdma1 mdma2
UDMA modes: udma0 udma1 udma2 udma3 udma4 *udma5
AdvancedPM=yes: mode=0x80 (128) WriteCache=enabled
Drive conforms to: ATA/ATAPI-6 T13 1410D revision 3a:
The initialization failes on
hda: max request size:128KiB
after this the kernel hangs.
Report of ver_linux (on other kernel):
Linux mobile.mynetwork.de 2.6.3-rc2-mm1 #1 Fri Feb 13 19:25:44 CET 2004
i686 GNU/Linux
Gnu C 3.3.3
Gnu make 3.80
util-linux 2.12
mount 2.12
module-init-tools 3.0-pre9
e2fsprogs 1.35-WIP
pcmcia-cs 3.2.6
PPP 2.4.2
nfs-utils 1.0.6
Linux C Library 2.3.2
Dynamic linker (ldd) 2.3.2
Procps 3.1.15
Net-tools 1.60
Console-tools 0.2.3
Sh-utils 5.0.91
Modules Loaded tun snd_via82xx snd_pcm snd_timer snd_ac97_codec
snd_page_alloc snd_mpu401_uart snd_rawmidi snd_seq_device snd atmel_cs
atmel ip_nat_ftp ip_conntrack_ftp ip_nat_irc ip_conntrack_irc ipt_REJECT
ipt_LOG ipt_limit ipt_MASQUERADE iptable_nat ipt_state iptable_filter
ip_conntrack via_rhine soundcore rtc
PCI-Information:
00:00.0 Host bridge: VIA Technologies, Inc. P/KN266 Host Bridge
Subsystem: Mitac: Unknown device 8375
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 8
Region 0: Memory at a0000000 (32-bit, prefetchable) [size=64M]
Capabilities: [a0] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA+ ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x1,x2,x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
FW- Rate=x4
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:01.0 PCI bridge: VIA Technologies, Inc. VT8633 [Apollo Pro266 AGP]
(prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort+ >SERR- <PERR+
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: 0000c000-0000dfff
Memory behind bridge: e0000000-efffffff
Prefetchable memory behind bridge: 90000000-9fffffff
BridgeCtl: Parity- SERR- NoISA- VGA+ MAbort- >Reset- FastB2B-
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:09.0 CardBus bridge: ENE Technology Inc CB1410 Cardbus Controller
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 168, Cache Line Size: 0x10 (64 bytes)
Interrupt: pin A routed to IRQ 11
Region 0: Memory at 10000000 (32-bit, non-prefetchable) [size=4K]
Bus: primary=00, secondary=02, subordinate=05, sec-latency=176
Memory window 0: 10400000-107ff000 (prefetchable)
Memory window 1: 10800000-10bff000
I/O window 0: 00004000-000040ff
I/O window 1: 00004400-000044ff
BridgeCtl: Parity- SERR- ISA- VGA- MAbort- >Reset+ 16bInt-
PostWrite+
16-bit legacy interface ports at 0001
00:0b.0 FireWire (IEEE 1394): VIA Technologies, Inc. IEEE 1394 Host
Controller (rev 80) (prog-if 10 [OHCI])
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (8000ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: Memory at fedff800 (32-bit, non-prefetchable) [size=2K]
Region 1: I/O ports at ff00 [size=128]
Capabilities: [50] Power Management version 2
Flags: PMEClk- DSI- D1- D2+ AuxCurrent=0mA
PME(D0-,D1-,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.0 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 10
Region 4: I/O ports at 1200 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.1 USB Controller: VIA Technologies, Inc. USB (rev 80) (prog-if 00
[UHCI])
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin B routed to IRQ 11
Region 4: I/O ports at 1300 [size=32]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:10.3 USB Controller: VIA Technologies, Inc. USB 2.0 (rev 82) (prog-if
20 [EHCI])
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32, Cache Line Size: 0x08 (32 bytes)
Interrupt: pin D routed to IRQ 11
Region 0: Memory at f0000000 (32-bit, non-prefetchable) [size=256]
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=375mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.0 ISA bridge: VIA Technologies, Inc. VT8235 ISA Bridge
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.1 IDE interface: VIA Technologies, Inc.
VT82C586A/B/VT82C686/A/B/VT8233/A/C/VT8235 PIPC Bus Master IDE (rev 06)
(prog-if 8a [Master SecP PriP])
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64
Interrupt: pin A routed to IRQ 0
Region 4: I/O ports at 1100 [size=16]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.5 Multimedia audio controller: VIA Technologies, Inc.
VT8233/A/8235 AC97 Audio Controller (rev 50)
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at e100 [size=256]
Capabilities: [c0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:11.6 Communication controller: VIA Technologies, Inc. Intel 537 [AC97
Modem] (rev 80)
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin C routed to IRQ 5
Region 0: I/O ports at e200 [size=256]
Capabilities: [d0] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
00:12.0 Ethernet controller: VIA Technologies, Inc. VT6102 [Rhine-II]
(rev 74)
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping+ SERR- FastB2B-
Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 32 (750ns min, 2000ns max), Cache Line Size: 0x08 (32
bytes)
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at e300 [size=256]
Region 1: Memory at f0000100 (32-bit, non-prefetchable) [size=256]
Capabilities: [40] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA
PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
01:00.0 VGA compatible controller: S3 Inc. VT8375 [ProSavage8
KM266/KL266] (prog-if 00 [VGA])
Subsystem: Mitac: Unknown device 8375
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop-
ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66Mhz+ UDF- FastB2B- ParErr- DEVSEL=medium
>TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (1000ns min, 63750ns max), Cache Line Size: 0x08
(32 bytes)
Interrupt: pin A routed to IRQ 10
Region 0: Memory at e0000000 (32-bit, non-prefetchable) [size=512K]
Region 1: Memory at 90000000 (32-bit, prefetchable) [size=128M]
Expansion ROM at 000c0000 [disabled] [size=64K]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA
PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [80] AGP version 2.0
Status: RQ=32 Iso- ArqSz=0 Cal=0 SBA- ITACoh- GART64-
HTrans- 64bit- FW- AGP3- Rate=x4
Command: RQ=1 ArqSz=0 Cal=0 SBA- AGP- GART64- 64bit-
FW- Rate=x4
next reply other threads:[~2004-02-19 14:55 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-02-19 14:53 Art Tevs [this message]
2004-02-19 15:26 ` PROBLEM: Bartlomiej Zolnierkiewicz
-- strict thread matches above, loose matches on Subject: below --
2012-12-27 13:36 PROBLEM: Philip Miller
2010-10-05 11:27 PROBLEM: blondquirk
2009-01-19 8:10 PROBLEM: Vincent Chapman
2006-08-31 6:54 PROBLEM: 董董侃
2004-05-22 15:30 PROBLEM: Cybermario
2004-05-16 19:33 PROBLEM: roger@msn
2004-04-24 18:55 PROBLEM: Harry
2003-11-23 2:10 Problem: taylordl
2003-11-23 2:54 ` Problem: Matt H.
2003-10-20 0:03 PROBLEM: Teemu Sohlman
2003-06-10 14:15 PROBLEM: BOVARD JAY D
2003-03-03 11:07 PROBLEM: roman duka
2003-03-03 11:38 ` PROBLEM: Russell King
2002-06-12 23:48 PROBLEM: James Drabb
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=4034CDF1.4090405@yahoo.de \
--to=arti_tevs@yahoo.de \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome