From: Tommy Faasen <tommy@zwanebloem.nl>
To: thinkliberty <thinkliberty@gmail.com>,
linux-kernel@vger.kernel.org,
USB development list <linux-usb-devel@lists.sourceforge.net>,
linux-usb-users@lists.sourceforge.net
Subject: Re: [bug?] usb device ok with ohci, fails to accept an address with uhci
Date: Wed, 23 Jun 2004 00:32:21 +0200 [thread overview]
Message-ID: <40D8B375.1080709@zwanebloem.nl> (raw)
In-Reply-To: <77709e760406221454272d8c61@mail.gmail.com>
thinkliberty wrote:
>Is there an option for legacy support for USB in the BIOS?
>
>
>
No the closest thing is usb keyboard support, I tried both options.
>Are You using a hub to connect the device? or is it directly in to the
>USB port on the motherboard?
>
>
>
It's directly connected to the mainboard.
Regards,
Tommy
>On Tue, 22 Jun 2004 21:58:49 +0200, Tommy Faasen <tommy@zwanebloem.nl> wrote:
>
>
>>Hi,
>>
>>I have a sweex usb-wifi stick see also
>>http://sourceforge.net/projects/linux-lc100020/ and it's forums.
>>And I have 2 machines
>>Machine 1: Via kt133a chipset -> uhci_hcd
>>Machine 2: Sis 748 Chipset -> ohci_hcd
>>
>>The device works without a problem on machine 2 with at least kernels
>>2.6.6 and 2.6.7.
>>The usb wifi stick fails to accept an address on machine 1. There is a
>>good faq about it with things you can try. (turn off acpi, irq for usb,
>>no irq sharing, removing all pci cards,etc) I tried everything but with
>>no luck.
>>I tried kernels 2.4.26 till and including 2.6.7 without luck, however on
>>the same machine is also connected an usb joystick that works without a
>>problem, so my usb does work.
>>
>>The usb wifi stick is known to need to get a descriptor before settings
>>it's address but even with this patch I can't get it to work ( I didn't
>>need the patch for machine 2).
>>
>>I read some usb specs/docs kernel usb stuff, but since I'm no expert I
>>cannot see where the problem is, therefore posted below is some
>>information that hopefully is helpfull to you.
>>
>>Please let me know what else I can do to help,
>>
>>Tommy
>>
>>Dmesg output:
>>uhci_hcd 0000:00:07.2: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>>Controller
>>uhci_hcd 0000:00:07.2: irq 10, io base 0000d400
>>uhci_hcd 0000:00:07.2: new USB bus registered, assigned bus number 1
>>uhci_hcd 0000:00:07.2: detected 2 ports
>>usb usb1: new device strings: Mfr=3, Product=2, SerialNumber=1
>>usb usb1: default language 0x0409
>>usb usb1: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
>>usb usb1: Manufacturer: Linux 2.6.7 uhci_hcd
>>usb usb1: SerialNumber: 0000:00:07.2
>>usb usb1: hotplug
>>usb usb1: adding 1-0:1.0 (config #1, interface 0)
>>usb 1-0:1.0: hotplug
>>hub 1-0:1.0: usb_probe_interface
>>hub 1-0:1.0: usb_probe_interface - got id
>>hub 1-0:1.0: USB hub found
>>hub 1-0:1.0: 2 ports detected
>>hub 1-0:1.0: standalone hub
>>hub 1-0:1.0: no power switching (usb 1.0)
>>hub 1-0:1.0: individual port over-current protection
>>hub 1-0:1.0: power on to power good time: 2ms
>>hub 1-0:1.0: local power source is good
>>PCI: Found IRQ 10 for device 0000:00:07.3
>>PCI: Sharing IRQ 10 with 0000:00:07.2
>>PCI: Sharing IRQ 10 with 0000:00:0d.0
>>PCI: Sharing IRQ 10 with 0000:00:0b.0
>>uhci_hcd 0000:00:07.3: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>>Controller (#2)
>>uhci_hcd 0000:00:07.3: irq 10, io base 0000d800
>>uhci_hcd 0000:00:07.3: new USB bus registered, assigned bus number 2
>>uhci_hcd 0000:00:07.3: detected 2 ports
>>usb usb2: new device strings: Mfr=3, Product=2, SerialNumber=1
>>usb usb2: default language 0x0409
>>usb usb2: Product: VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1
>>Controller (#2)
>>usb usb2: Manufacturer: Linux 2.6.7 uhci_hcd
>>usb usb2: SerialNumber: 0000:00:07.3
>>usb usb2: hotplug
>>usb usb2: adding 2-0:1.0 (cuhci_hcd 0000:00:07.2: port 1 portsc 01ab
>>hub 1-0:1.0: port 1, status 0301, change 0003, 1.5 Mb/s
>>uhci_hcd 0000:00:07.2: port 1 portsc 01a9
>>uhci_hcd 0000:00:07.2: port 1 portsc 01a9
>>uhci_hcd 0000:00:07.2: port 1 portsc 01a9
>>usb 2-0:1.0: hotplug
>>hub 2-0:1.0: usb_probe_interface
>>hub 2-0:1.0: usb_probe_interface - got id
>>hub 2-0:1.0: USB hub found
>>hub 2-0:1.0: 2 ports detected
>>hub 2-0:1.0: standalone hub
>>hub 2-0:1.0: no power switching (usb 1.0)
>>hub 2-0:1.0: individual port over-current protection
>>hub 2-0:1.0: power on to power good time: 2ms
>>hub 2-0:1.0: local power source is good
>>uhci_hcd 0000:00:07.2: port 1 portsc 01a9
>>uhci_hcd 0000:00:07.2: port 1 portsc 01a9
>>hub 1-0:1.0: debounce: port 1: delay 100ms stable 4 status 0x301
>>usb 1-1: new low speed USB device using address 2
>>usb 1-1: skipped 1 descriptor after interface
>>usb 1-1: new device strings: Mfr=4, Product=32, SerialNumber=0
>>usb 1-1: default language 0x0409
>>usb 1-1: Product: WingMan Gamepad
>>usb 1-1: Manufacturer: Logitech Inc.
>>usb 1-1: hotplug
>>usb 1-1: adding 1-1:1.0 (config #1, interface 0)
>>usb 1-1:1.0: hotplug
>>uhci_hcd 0000:00:07.2: port 2 portsc 018a
>>hub 1-0:1.0: port 2, status 0300, change 0003, 1.5 Mb/s
>>uhci_hcd 0000:00:07.2: port 2 portsc 0188
>>hub 1-0:1.0: port 2 enable change, status 00000300
>>uhci_hcd 0000:00:07.3: port 1 portsc 018a
>>hub 2-0:1.0: port 1, status 0300, change 0003, 1.5 Mb/s
>>uhci_hcd 0000:00:07.3: port 2 portsc 008a
>>hub 2-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
>>uhci_hcd 0000:00:07.3: port 1 portsc 0188
>>hub 2-0:1.0: port 1 enable change, status 00000300
>>uhci_hcd 0000:00:07.3: port 2 portsc 0088
>>hub 2-0:1.0: port 2 enable change, status 00000100
>>uhci_hcd 0000:00:07.3: suspend_hc
>>uhci_hcd 0000:00:07.2: port 2 portsc 0093
>>hub 1-0:1.0: port 2, status 0101, change 0001, 12 Mb/s
>>hub 1-0:1.0: debounce: port 2: delay 100ms stable 4 status 0x101
>>usb 1-2: new full speed USB device using address 3
>>uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
>>[e6fe4240] link (26fe41e2) element (26fe3040)
>> 0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
>>DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
>> 1: [e6fe3080] link (26fe30c0) e3 SPD Active Length=0 MaxLen=7 DT1
>>EndPt=0 Dev=0, PID=69(IN) (buf=273ddf14)
>> 2: [e6fe30c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
>>EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
>>
>>uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
>>[e6fe4240] link (26fe41e2) element (26fe3040)
>> 0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
>>DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
>> 1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
>>EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
>>
>>uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
>>[e6fe4240] link (26fe41e2) element (26fe3040)
>> 0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
>>DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
>> 1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
>>EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
>>
>>usb 1-2: device not accepting address 3, error -71
>>usb 1-2: new full speed USB device using address 4
>>uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
>>[e6fe4240] link (26fe41e2) element (26fe3040)
>> 0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
>>DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
>> 1: [e6fe3080] link (26fe30c0) e3 SPD Active Length=0 MaxLen=7 DT1
>>EndPt=0 Dev=0, PID=69(IN) (buf=273ddf14)
>> 2: [e6fe30c0] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
>>EndPt=0 Dev=0, PID=e1(OUT) (buf=00000000)
>>
>>uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
>>[e6fe4240] link (26fe41e2) element (26fe3040)
>> 0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
>>DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
>> 1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
>>EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
>>
>>uhci_hcd 0000:00:07.2: uhci_result_control: failed with status 440000
>>[e6fe4240] link (26fe41e2) element (26fe3040)
>> 0: [e6fe3040] link (26fe3080) e0 Stalled CRC/Timeo Length=7 MaxLen=7
>>DT0 EndPt=0 Dev=0, PID=2d(SETUP) (buf=255aeec8)
>> 1: [e6fe3080] link (00000001) e3 IOC Active Length=0 MaxLen=7ff DT1
>>EndPt=0 Dev=0, PID=69(IN) (buf=00000000)
>>
>>usb 1-2: device not accepting address 4, error -71
>>uhci_hcd 0000:00:07.2: port 2 portsc 008a
>>hub 1-0:1.0: port 2, status 0100, change 0003, 12 Mb/s
>>uhci_hcd 0000:00:07.2: port 2 portsc 0088
>>
>>lspci -v
>>00:00.0 Host bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133]
>>(rev 03)
>> Flags: bus master, medium devsel, latency 8
>> Memory at d0000000 (32-bit, prefetchable) [size=128M]
>> Capabilities: [a0] AGP version 2.0
>> Capabilities: [c0] Power Management version 2
>>
>>00:01.0 PCI bridge: VIA Technologies, Inc. VT8363/8365 [KT133/KM133 AGP]
>>(prog-if 00 [Normal decode])
>> Flags: bus master, 66Mhz, medium devsel, latency 0
>> Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
>> Memory behind bridge: da000000-dbffffff
>> Prefetchable memory behind bridge: d8000000-d9ffffff
>> Capabilities: [80] Power Management version 2
>>
>>00:07.0 ISA bridge: VIA Technologies, Inc. VT82C686 [Apollo Super South]
>>(rev 40)
>> Subsystem: VIA Technologies, Inc. VT82C686/A PCI to ISA Bridge
>> Flags: bus master, stepping, medium devsel, latency 0
>> Capabilities: [c0] Power Management version 2
>>
>>00:07.1 IDE interface: VIA Technologies, Inc. Bus Master IDE (rev 06)
>>(prog-if 8a [Master SecP PriP])
>> Subsystem: VIA Technologies, Inc. Bus Master IDE
>> Flags: bus master, medium devsel, latency 32
>> I/O ports at d000 [size=16]
>> Capabilities: [c0] Power Management version 2
>>
>>00:07.2 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
>>(prog-if 00 [UHCI])
>> Subsystem: Unknown device 0925:1234
>> Flags: bus master, medium devsel, latency 32, IRQ 10
>> I/O ports at d400 [size=32]
>> Capabilities: [80] Power Management version 2
>>
>>00:07.3 USB Controller: VIA Technologies, Inc. UHCI USB (rev 16)
>>(prog-if 00 [UHCI])
>> Subsystem: Unknown device 0925:1234
>> Flags: bus master, medium devsel, latency 32, IRQ 10
>> I/O ports at d800 [size=32]
>> Capabilities: [80] Power Management version 2
>>
>>00:07.4 Bridge: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI] (rev 40)
>> Subsystem: VIA Technologies, Inc. VT82C686 [Apollo Super ACPI]
>> Flags: medium devsel, IRQ 7
>> Capabilities: [68] Power Management version 2
>>
>>00:09.0 SCSI storage controller: Adaptec AHA-2940U2/W
>> Subsystem: Adaptec: Unknown device a180
>> Flags: bus master, medium devsel, latency 32, IRQ 11
>> BIST result: 00
>> I/O ports at dc00 [disabled] [size=256]
>> Memory at dd200000 (64-bit, non-prefetchable) [size=4K]
>> Expansion ROM at <unassigned> [disabled] [size=128K]
>> Capabilities: [dc] Power Management version 1
>>
>>00:0d.0 Ethernet controller: Intel Corp. 82557 [Ethernet Pro 100] (rev 05)
>> Subsystem: Compaq Computer Corporation NC3120
>> Flags: bus master, medium devsel, latency 32, IRQ 10
>> Memory at dd203000 (32-bit, prefetchable) [size=4K]
>> I/O ports at ec00 [size=32]
>> Memory at dd100000 (32-bit, non-prefetchable) [size=1M]
>> Expansion ROM at <unassigned> [disabled] [size=1M]
>> Capabilities: [dc] Power Management version 1
>>
>>01:00.0 VGA compatible controller: nVidia Corporation Vanta [NV6] (rev
>>15) (prog-if 00 [VGA])
>> Subsystem: Unknown device 17f2:4010
>> Flags: bus master, 66Mhz, medium devsel, latency 32, IRQ 5
>> Memory at da000000 (32-bit, non-prefetchable) [size=16M]
>> Memory at d8000000 (32-bit, prefetchable) [size=32M]
>> Expansion ROM at <unassigned> [disabled] [size=64K]
>> Capabilities: [60] Power Management version 1
>> Capabilities: [44] AGP version 2.0
>>
>>cat /proc/bus/usb/devices
>>
>>T: Bus=02 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
>>B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
>>D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>>P: Vendor=0000 ProdID=0000 Rev= 2.06
>>S: Manufacturer=Linux 2.6.7 uhci_hcd
>>S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller (#2)
>>S: SerialNumber=0000:00:07.3
>>C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
>>I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
>>E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
>>
>>T: Bus=01 Lev=00 Prnt=00 Port=00 Cnt=00 Dev#= 1 Spd=12 MxCh= 2
>>B: Alloc= 0/900 us ( 0%), #Int= 0, #Iso= 0
>>D: Ver= 1.10 Cls=09(hub ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>>P: Vendor=0000 ProdID=0000 Rev= 2.06
>>S: Manufacturer=Linux 2.6.7 uhci_hcd
>>S: Product=VIA Technologies, Inc. VT82xxxxx UHCI USB 1.1 Controller
>>S: SerialNumber=0000:00:07.2
>>C:* #Ifs= 1 Cfg#= 1 Atr=c0 MxPwr= 0mA
>>I: If#= 0 Alt= 0 #EPs= 1 Cls=09(hub ) Sub=00 Prot=00 Driver=hub
>>E: Ad=81(I) Atr=03(Int.) MxPS= 2 Ivl=255ms
>>
>>T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 2 Spd=1.5 MxCh= 0
>>D: Ver= 1.00 Cls=00(>ifc ) Sub=00 Prot=00 MxPS= 8 #Cfgs= 1
>>P: Vendor=046d ProdID=c209 Rev= 1.03
>>S: Manufacturer=Logitech Inc.
>>S: Product=WingMan Gamepad
>>C:* #Ifs= 1 Cfg#= 1 Atr=80 MxPwr= 40mA
>>I: If#= 0 Alt= 0 #EPs= 1 Cls=03(HID ) Sub=00 Prot=00 Driver=(none)
>>E: Ad=81(I) Atr=03(Int.) MxPS= 8 Ivl=10ms
>>
>>cat /proc/interrupts
>> CPU0
>> 0: 2040665 XT-PIC timer
>> 1: 8 XT-PIC i8042
>> 2: 0 XT-PIC cascade
>> 8: 1 XT-PIC rtc
>> 10: 71185 XT-PIC EMU10K1, uhci_hcd, uhci_hcd, eth1
>> 11: 19586 XT-PIC aic7xxx
>> 12: 30728 XT-PIC Bt87x audio, bttv0, eth0
>> 15: 18 XT-PIC ide1
>>NMI: 0
>>LOC: 2040654
>>ERR: 2234
>>MIS: 0
>>
>>-
>>To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
>>the body of a message to majordomo@vger.kernel.org
>>More majordomo info at http://vger.kernel.org/majordomo-info.html
>>Please read the FAQ at http://www.tux.org/lkml/
>>
>>
>>
>
>
>
>
prev parent reply other threads:[~2004-06-22 22:35 UTC|newest]
Thread overview: 2+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-06-22 19:58 Tommy Faasen
[not found] ` <77709e760406221454272d8c61@mail.gmail.com>
2004-06-22 22:32 ` Tommy Faasen [this message]
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=40D8B375.1080709@zwanebloem.nl \
--to=tommy@zwanebloem.nl \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-usb-devel@lists.sourceforge.net \
--cc=linux-usb-users@lists.sourceforge.net \
--cc=thinkliberty@gmail.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®