From: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
To: Shawn Guo <shengchao.guo@oss.qualcomm.com>
Cc: Vikash Garodia <vikash.garodia@oss.qualcomm.com>,
Dikshita Agarwal <dikshita.agarwal@oss.qualcomm.com>,
Abhinav Kumar <abhinav.kumar@linux.dev>,
Bryan O'Donoghue <bod@kernel.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Rob Herring <robh@kernel.org>,
Krzysztof Kozlowski <krzk+dt@kernel.org>,
Conor Dooley <conor+dt@kernel.org>,
Bjorn Andersson <andersson@kernel.org>,
Konrad Dybcio <konradybcio@kernel.org>,
Abel Vesa <abelvesa@kernel.org>,
linux-media@vger.kernel.org, linux-arm-msm@vger.kernel.org,
devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
Subject: Re: [PATCH 2/4] arm64: dts: qcom: nord: Add iris video node
Date: Mon, 21 Sep 2026 11:10:54 +0530 [thread overview]
Message-ID: <43e757dd-17f7-5b03-33e4-5c567e164be2@oss.qualcomm.com> (raw)
In-Reply-To: <aq_cmcYa1wL69Hq4@QCOM-aGQu4IUr3Y>
On 9/20/2026 6:46 PM, Shawn Guo wrote:
> On Sat, Sep 19, 2026 at 10:14:56AM +0530, Vishnu Reddy wrote:
>> Add iris video codec to nord SoC, which comes with significantly different
>> powering up sequence than previous platforms, thus different clocks and
>> resets.
>>
>> Signed-off-by: Vishnu Reddy <busanna.reddy@oss.qualcomm.com>
>> ---
>> arch/arm64/boot/dts/qcom/nord-embedded.dtsi | 114 ++++++++++++++++++++++++++++
>> 1 file changed, 114 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/nord-embedded.dtsi b/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
>> index 74f4e6be8652..03f827f3e5fc 100644
>> --- a/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/nord-embedded.dtsi
>> @@ -1428,6 +1428,120 @@ camcc: clock-controller@9ce0000 {
>> #power-domain-cells = <1>;
>> };
>>
>> + iris: video-codec@aa00000 {
>> + compatible = "qcom,nord-iris", "qcom,glymur-iris";
>> + reg = <0x0 0x0aa00000 0x0 0xf0000>;
> nord-embedded.dtsi is a place to accommodate Nord Embedded variant
> specific resource descriptions, like clock, regulator, pinctrl,
> interconnect, power domain, PHY, etc. The rest of descriptions should
> go to nord.dtsi, like reg, interrupts, iommu, dma, etc.
Will check and move it to nord.dtsi if no issues are found.
> Shawn
>
>> +
>> + clocks = <&nwgcc NW_GCC_VIDEO_AXI0_CLK>,
>> + <&videocc VIDEO_CC_MVS0C_CLK>,
>> + <&videocc VIDEO_CC_MVS0_CLK>,
>> + <&nwgcc NW_GCC_VIDEO_AXI0C_CLK>,
>> + <&videocc VIDEO_CC_MVS0C_FREERUN_CLK>,
>> + <&videocc VIDEO_CC_MVS0_FREERUN_CLK>,
>> + <&nwgcc NW_GCC_VIDEO_AXI1_CLK>,
>> + <&videocc VIDEO_CC_MVS1_CLK>,
>> + <&videocc VIDEO_CC_MVS1_FREERUN_CLK>;
>> + clock-names = "core_iface",
>> + "core",
>> + "vcodec0_core",
>> + "vcodec0_iface",
>> + "core_freerun",
>> + "vcodec0_core_freerun",
>> + "vcodec1_iface",
>> + "vcodec1_core",
>> + "vcodec1_core_freerun";
>> +
>> + dma-coherent;
>> +
>> + interconnects = <&hscnoc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
>> + &config_noc SLAVE_VENUS_CFG QCOM_ICC_TAG_ACTIVE_ONLY>,
>> + <&mmss_noc MASTER_VIDEO_MVP0 QCOM_ICC_TAG_ALWAYS
>> + &mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>;
>> + interconnect-names = "cpu-cfg",
>> + "video-mem";
>> +
>> + interrupts = <GIC_SPI 174 IRQ_TYPE_LEVEL_HIGH>;
>> +
>> + memory-region = <&video_mem>;
>> +
>> + operating-points-v2 = <&iris_opp_table>;
>> +
>> + power-domains = <&videocc VIDEO_CC_MVS0C_GDSC>,
>> + <&videocc VIDEO_CC_MVS0_GDSC>,
>> + <&rpmhpd RPMHPD_MXC>,
>> + <&rpmhpd RPMHPD_MMCX>,
>> + <&videocc VIDEO_CC_MVS1_GDSC>;
>> + power-domain-names = "venus",
>> + "vcodec0",
>> + "mxc",
>> + "mmcx",
>> + "vcodec1";
>> +
>> + resets = <&nwgcc NW_GCC_VIDEO_AXI0_CLK_ARES>,
>> + <&nwgcc NW_GCC_VIDEO_AXI0C_CLK_ARES>,
>> + <&videocc VIDEO_CC_MVS0C_FREERUN_CLK_ARES>,
>> + <&videocc VIDEO_CC_MVS0_FREERUN_CLK_ARES>,
>> + <&nwgcc NW_GCC_VIDEO_AXI1_CLK_ARES>,
>> + <&videocc VIDEO_CC_MVS1_FREERUN_CLK_ARES>;
>> + reset-names = "core_bus",
>> + "vcodec0_bus",
>> + "core",
>> + "vcodec0_core",
>> + "vcodec1_bus",
>> + "vcodec1_core";
>> +
>> + #address-cells = <1>;
>> + #size-cells = <1>;
>> + dma-ranges = <0x0 0x0 0x0 0xffe00000>;
>> +
>> + status = "disabled";
>> +
>> + non-pixel {
>> + iommus = <&apps_smmu_1 0x0940 0x20>,
>> + <&apps_smmu_1 0x0944 0x0>,
>> + <&apps_smmu_1 0x0960 0x20>;
>> + iommu-ranges = <0x25800000 0xda600000>;
>> + };
>> +
>> + pixel {
>> + iommus = <&apps_smmu_1 0x0943 0x0>;
>> + };
>> +
>> + iris_opp_table: opp-table {
>> + compatible = "operating-points-v2";
>> +
>> + opp-240000000 {
>> + opp-hz = /bits/ 64 <240000000 240000000 360000000>;
>> + required-opps = <&rpmhpd_opp_svs>,
>> + <&rpmhpd_opp_svs>;
>> + };
>> +
>> + opp-435000000 {
>> + opp-hz = /bits/ 64 <435000000 435000000 652500000>;
>> + required-opps = <&rpmhpd_opp_svs_l1>,
>> + <&rpmhpd_opp_svs_l1>;
>> + };
>> +
>> + opp-480000000 {
>> + opp-hz = /bits/ 64 <480000000 480000000 720000000>;
>> + required-opps = <&rpmhpd_opp_svs_l1>,
>> + <&rpmhpd_opp_nom>;
>> + };
>> +
>> + opp-533333333 {
>> + opp-hz = /bits/ 64 <533333333 533333333 800000000>;
>> + required-opps = <&rpmhpd_opp_svs_l1>,
>> + <&rpmhpd_opp_turbo>;
>> + };
>> +
>> + opp-560000000 {
>> + opp-hz = /bits/ 64 <560000000 560000000 840000000>;
>> + required-opps = <&rpmhpd_opp_nom>,
>> + <&rpmhpd_opp_turbo_l1>;
>> + };
>> + };
>> + };
>> +
>> videocc: clock-controller@aaf0000 {
>> compatible = "qcom,nord-videocc";
>> reg = <0x0 0x0aaf0000 0x0 0x10000>;
>>
>> --
>> 2.34.1
>>
>>
next prev parent reply other threads:[~2026-09-21 5:41 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-19 4:44 [PATCH 0/4] media: iris: Add support for nord platform Vishnu Reddy
2026-09-19 4:44 ` [PATCH 1/4] dt-bindings: media: qcom,nord-iris: Add nord video codec Vishnu Reddy
2026-09-20 13:08 ` Shawn Guo
2026-09-21 5:39 ` Vishnu Reddy
2026-09-19 4:44 ` [PATCH 2/4] arm64: dts: qcom: nord: Add iris video node Vishnu Reddy
2026-09-20 13:16 ` Shawn Guo
2026-09-21 5:40 ` Vishnu Reddy [this message]
2026-09-19 4:44 ` [PATCH 3/4] arm64: dts: qcom: nord-ride-embedded: Enable iris video codec node Vishnu Reddy
2026-09-21 8:07 ` Abel Vesa
2026-09-19 4:44 ` [PATCH 4/4] arm64: dts: qcom: nord-rrd: " Vishnu Reddy
2026-09-21 8:07 ` Abel Vesa
2026-09-20 13:27 ` [PATCH 0/4] media: iris: Add support for nord platform Shawn Guo
2026-09-21 5:45 ` Vishnu Reddy
2026-09-23 13:47 ` Shawn Guo
2026-09-24 6:22 ` Vishnu Reddy
2026-09-24 7:09 ` Shawn Guo
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=43e757dd-17f7-5b03-33e4-5c567e164be2@oss.qualcomm.com \
--to=busanna.reddy@oss.qualcomm.com \
--cc=abelvesa@kernel.org \
--cc=abhinav.kumar@linux.dev \
--cc=andersson@kernel.org \
--cc=bod@kernel.org \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=dikshita.agarwal@oss.qualcomm.com \
--cc=konradybcio@kernel.org \
--cc=krzk+dt@kernel.org \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=mchehab@kernel.org \
--cc=robh@kernel.org \
--cc=shengchao.guo@oss.qualcomm.com \
--cc=vikash.garodia@oss.qualcomm.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®