[PATCH v2 0/4] USB-C TCPM Orientation Support

[PATCH v2 0/4] USB-C TCPM Orientation Support

[Marco Felsch]

Hi,

this adds the support to controll the optional connector-orientation
available on some TCPC from the TCPM.

I used an custom board with OnSemi FUSB307B TCPC which is spec [1]
compatible but albeit the spec [1] says that this pin is controlled by
the TCPC if 'TCPC_CONTROL.DebugAccessoryControl = 0' it isn't at least
for this device.

I'm unsure if the usb tcpci spec has an copy'n'paste failure since
'TCPC_CONTROL.DebugAccessoryControl' shouldn't control the state of the
'connector orientation' pin or if the OnSemi FUSB307B has an HW bug.
Since on my device the 'TCPC_CONTROL.DebugAccessoryControl' is set to
0 but the register wasn't updated automatically.

Regards,
  Marco

[1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf


Marco Felsch (4):
  dt-bindings: usb: typec-tcpci: add tcpci fallback binding
  usb: typec: tcpci: add generic tcpci fallback compatible
  usb: typec: tcpm: add support to set tcpc connector orientatition
  usb: typec: tcpci: add support to set connector orientation

 .../devicetree/bindings/usb/nxp,ptn5110.yaml  |  4 +-
 drivers/usb/typec/tcpm/tcpci.c                | 45 +++++++++++++++++++
 drivers/usb/typec/tcpm/tcpm.c                 |  6 +++
 include/linux/usb/tcpci.h                     |  8 ++++
 include/linux/usb/tcpm.h                      |  2 +
 5 files changed, 64 insertions(+), 1 deletion(-)

-- 
2.39.2

[PATCH v2 1/4] dt-bindings: usb: typec-tcpci: add tcpci fallback binding

[Marco Felsch]

The NXP PTN5110 [1] is an TCPCI [2] compatible chip, so add the fallback
binding.

[1] https://www.nxp.com/docs/en/data-sheet/PTN5110.pdf
[2] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
v2:
- rephrase commit message

 Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml | 4 +++-
 1 file changed, 3 insertions(+), 1 deletion(-)

diff --git a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
index eaedb4cc6b6c..7bd7bbbac9e0 100644
--- a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
+++ b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
@@ -11,7 +11,9 @@ maintainers:
 
 properties:
   compatible:
-    const: nxp,ptn5110
+    enum:
+      - nxp,ptn5110
+      - tcpci
 
   reg:
     maxItems: 1
-- 
2.39.2

[PATCH v2 2/4] usb: typec: tcpci: add generic tcpci fallback compatible

[Marco Felsch]

The driver already support the tcpci binding for the i2c_device_id so
add the support for the of_device_id too.

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
v2:
- no changes

 drivers/usb/typec/tcpm/tcpci.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/usb/typec/tcpm/tcpci.c b/drivers/usb/typec/tcpm/tcpci.c
index 0ee3e6e29bb1..7118551827f6 100644
--- a/drivers/usb/typec/tcpm/tcpci.c
+++ b/drivers/usb/typec/tcpm/tcpci.c
@@ -889,6 +889,7 @@ MODULE_DEVICE_TABLE(i2c, tcpci_id);
 #ifdef CONFIG_OF
 static const struct of_device_id tcpci_of_match[] = {
 	{ .compatible = "nxp,ptn5110", },
+	{ .compatible = "tcpci", },
 	{},
 };
 MODULE_DEVICE_TABLE(of, tcpci_of_match);
-- 
2.39.2

[PATCH v2 3/4] usb: typec: tcpm: add support to set tcpc connector orientatition

[Marco Felsch]

This adds the support to set the connector orientation value
accordingly. This is part of the optional CONFIG_STANDARD_OUTPUT
register 0x18, specified within the USB port controller spsicification
rev. 2.0 [1].

[1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
v2:
- no changes

 drivers/usb/typec/tcpm/tcpm.c | 6 ++++++
 include/linux/usb/tcpm.h      | 2 ++
 2 files changed, 8 insertions(+)

diff --git a/drivers/usb/typec/tcpm/tcpm.c b/drivers/usb/typec/tcpm/tcpm.c
index 5945e3a2b0f7..85ca26687324 100644
--- a/drivers/usb/typec/tcpm/tcpm.c
+++ b/drivers/usb/typec/tcpm/tcpm.c
@@ -1099,6 +1099,12 @@ static int tcpm_set_roles(struct tcpm_port *port, bool attached,
 	if (ret < 0)
 		return ret;
 
+	if (port->tcpc->set_orientation) {
+		ret = port->tcpc->set_orientation(port->tcpc, orientation);
+		if (ret < 0)
+			return ret;
+	}
+
 	port->pwr_role = role;
 	port->data_role = data;
 	typec_set_data_role(port->typec_port, data);
diff --git a/include/linux/usb/tcpm.h b/include/linux/usb/tcpm.h
index 65fac5e1f317..93b681ff3ef9 100644
--- a/include/linux/usb/tcpm.h
+++ b/include/linux/usb/tcpm.h
@@ -133,6 +133,8 @@ struct tcpc_dev {
 		      enum typec_cc_status *cc2);
 	int (*set_polarity)(struct tcpc_dev *dev,
 			    enum typec_cc_polarity polarity);
+	int (*set_orientation)(struct tcpc_dev *dev,
+			       enum typec_orientation orientation);
 	int (*set_vconn)(struct tcpc_dev *dev, bool on);
 	int (*set_vbus)(struct tcpc_dev *dev, bool on, bool charge);
 	int (*set_current_limit)(struct tcpc_dev *dev, u32 max_ma, u32 mv);
-- 
2.39.2

[PATCH v2 4/4] usb: typec: tcpci: add support to set connector orientation

[Marco Felsch]

This add the support to set the optional connector orientation bit which
is part of the optional CONFIG_STANDARD_OUTPUT register 0x18 [1]. This
allows system designers to connect the tcpc orientation pin directly to
the 2:1 ss-mux.

[1] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf

Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
---
v2:
- Make use of fallthrough

 drivers/usb/typec/tcpm/tcpci.c | 44 ++++++++++++++++++++++++++++++++++
 include/linux/usb/tcpci.h      |  8 +++++++
 2 files changed, 52 insertions(+)

diff --git a/drivers/usb/typec/tcpm/tcpci.c b/drivers/usb/typec/tcpm/tcpci.c
index 7118551827f6..73a52e7f95c2 100644
--- a/drivers/usb/typec/tcpm/tcpci.c
+++ b/drivers/usb/typec/tcpm/tcpci.c
@@ -67,6 +67,18 @@ static int tcpci_write16(struct tcpci *tcpci, unsigned int reg, u16 val)
 	return regmap_raw_write(tcpci->regmap, reg, &val, sizeof(u16));
 }
 
+static bool tcpci_check_std_output_cap(struct regmap *regmap, u8 mask)
+{
+	unsigned int reg;
+	int ret;
+
+	ret = regmap_read(regmap, TCPC_STD_OUTPUT_CAP, &reg);
+	if (ret < 0)
+		return ret;
+
+	return (reg & mask) == mask;
+}
+
 static int tcpci_set_cc(struct tcpc_dev *tcpc, enum typec_cc_status cc)
 {
 	struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
@@ -301,6 +313,28 @@ static int tcpci_set_polarity(struct tcpc_dev *tcpc,
 			   TCPC_TCPC_CTRL_ORIENTATION : 0);
 }
 
+static int tcpci_set_orientation(struct tcpc_dev *tcpc,
+				 enum typec_orientation orientation)
+{
+	struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
+	unsigned int reg;
+
+	switch (orientation) {
+	case TYPEC_ORIENTATION_NONE:
+		/* We can't put a single output into high impedance */
+		fallthrough;
+	case TYPEC_ORIENTATION_NORMAL:
+		reg = TCPC_CONFIG_STD_OUTPUT_ORIENTATION_NORMAL;
+		break;
+	case TYPEC_ORIENTATION_REVERSE:
+		reg = TCPC_CONFIG_STD_OUTPUT_ORIENTATION_FLIPPED;
+		break;
+	}
+
+	return regmap_update_bits(tcpci->regmap, TCPC_CONFIG_STD_OUTPUT,
+				  TCPC_CONFIG_STD_OUTPUT_ORIENTATION_MASK, reg);
+}
+
 static void tcpci_set_partner_usb_comm_capable(struct tcpc_dev *tcpc, bool capable)
 {
 	struct tcpci *tcpci = tcpc_to_tcpci(tcpc);
@@ -808,6 +842,9 @@ struct tcpci *tcpci_register_port(struct device *dev, struct tcpci_data *data)
 	if (tcpci->data->vbus_vsafe0v)
 		tcpci->tcpc.is_vbus_vsafe0v = tcpci_is_vbus_vsafe0v;
 
+	if (tcpci->data->set_orientation)
+		tcpci->tcpc.set_orientation = tcpci_set_orientation;
+
 	err = tcpci_parse_config(tcpci);
 	if (err < 0)
 		return ERR_PTR(err);
@@ -851,6 +888,13 @@ static int tcpci_probe(struct i2c_client *client)
 	if (err < 0)
 		return err;
 
+	err = tcpci_check_std_output_cap(chip->data.regmap,
+					 TCPC_STD_OUTPUT_CAP_ORIENTATION);
+	if (err < 0)
+		return err;
+
+	chip->data.set_orientation = err;
+
 	chip->tcpci = tcpci_register_port(&client->dev, &chip->data);
 	if (IS_ERR(chip->tcpci))
 		return PTR_ERR(chip->tcpci);
diff --git a/include/linux/usb/tcpci.h b/include/linux/usb/tcpci.h
index 467e8045e9f8..f2bfb4250366 100644
--- a/include/linux/usb/tcpci.h
+++ b/include/linux/usb/tcpci.h
@@ -47,6 +47,9 @@
 #define TCPC_SINK_FAST_ROLE_SWAP	BIT(0)
 
 #define TCPC_CONFIG_STD_OUTPUT		0x18
+#define TCPC_CONFIG_STD_OUTPUT_ORIENTATION_MASK		BIT(0)
+#define TCPC_CONFIG_STD_OUTPUT_ORIENTATION_NORMAL	0
+#define TCPC_CONFIG_STD_OUTPUT_ORIENTATION_FLIPPED	1
 
 #define TCPC_TCPC_CTRL			0x19
 #define TCPC_TCPC_CTRL_ORIENTATION	BIT(0)
@@ -127,6 +130,7 @@
 #define TCPC_DEV_CAP_2			0x26
 #define TCPC_STD_INPUT_CAP		0x28
 #define TCPC_STD_OUTPUT_CAP		0x29
+#define TCPC_STD_OUTPUT_CAP_ORIENTATION	BIT(0)
 
 #define TCPC_MSG_HDR_INFO		0x2e
 #define TCPC_MSG_HDR_INFO_DATA_ROLE	BIT(3)
@@ -198,12 +202,16 @@ struct tcpci;
  *		Chip level drivers are expected to check for contaminant and call
  *		tcpm_clean_port when the port is clean to put the port back into
  *		toggling state.
+ * @set_orientation:
+ *		Optional; Enable setting the connector orientation
+ *		CONFIG_STANDARD_OUTPUT (0x18) bit0.
  */
 struct tcpci_data {
 	struct regmap *regmap;
 	unsigned char TX_BUF_BYTE_x_hidden:1;
 	unsigned char auto_discharge_disconnect:1;
 	unsigned char vbus_vsafe0v:1;
+	unsigned char set_orientation:1;
 
 	int (*init)(struct tcpci *tcpci, struct tcpci_data *data);
 	int (*set_vconn)(struct tcpci *tcpci, struct tcpci_data *data,
-- 
2.39.2

Re: [PATCH v2 1/4] dt-bindings: usb: typec-tcpci: add tcpci fallback binding

[Krzysztof Kozlowski]

On 15/02/2024 22:28, Marco Felsch wrote:
> The NXP PTN5110 [1] is an TCPCI [2] compatible chip, so add the fallback
> binding.
> 
> [1] https://www.nxp.com/docs/en/data-sheet/PTN5110.pdf
> [2] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf
> 
> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> ---
> v2:
> - rephrase commit message
> 
>  Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml | 4 +++-
>  1 file changed, 3 insertions(+), 1 deletion(-)
> 
> diff --git a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> index eaedb4cc6b6c..7bd7bbbac9e0 100644
> --- a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> +++ b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> @@ -11,7 +11,9 @@ maintainers:
>  
>  properties:
>    compatible:
> -    const: nxp,ptn5110
> +    enum:
> +      - nxp,ptn5110
> +      - tcpci

That's not a fallback, but enum. Fallback is "items" and then you could
also send a follow-up patchset (separate, so Greg won't take it) fixing
DTS (if not, let me know, so I will fix it).

Best regards,
Krzysztof

Re: [PATCH v2 1/4] dt-bindings: usb: typec-tcpci: add tcpci fallback binding

[Marco Felsch]

On 24-02-22, Krzysztof Kozlowski wrote:
> On 15/02/2024 22:28, Marco Felsch wrote:
> > The NXP PTN5110 [1] is an TCPCI [2] compatible chip, so add the fallback
> > binding.
> > 
> > [1] https://www.nxp.com/docs/en/data-sheet/PTN5110.pdf
> > [2] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf
> > 
> > Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> > ---
> > v2:
> > - rephrase commit message
> > 
> >  Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml | 4 +++-
> >  1 file changed, 3 insertions(+), 1 deletion(-)
> > 
> > diff --git a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> > index eaedb4cc6b6c..7bd7bbbac9e0 100644
> > --- a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> > +++ b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> > @@ -11,7 +11,9 @@ maintainers:
> >  
> >  properties:
> >    compatible:
> > -    const: nxp,ptn5110
> > +    enum:
> > +      - nxp,ptn5110
> > +      - tcpci
> 
> That's not a fallback, but enum. Fallback is "items" and then you could

Damn, you're right. Sorry.

> also send a follow-up patchset (separate, so Greg won't take it) fixing
> DTS (if not, let me know, so I will fix it).

Sry. but I don't get this. Why do I need to send a follow-up? Greg did
not apply anything, at least I didn't received an e-mail, that this
patchset was picked.

Regards,
  Marco


> 
> Best regards,
> Krzysztof
> 
> 

Re: [PATCH v2 1/4] dt-bindings: usb: typec-tcpci: add tcpci fallback binding

[Marco Felsch]

On 24-02-22, Marco Felsch wrote:
> On 24-02-22, Krzysztof Kozlowski wrote:
> > On 15/02/2024 22:28, Marco Felsch wrote:
> > > The NXP PTN5110 [1] is an TCPCI [2] compatible chip, so add the fallback
> > > binding.
> > > 
> > > [1] https://www.nxp.com/docs/en/data-sheet/PTN5110.pdf
> > > [2] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf
> > > 
> > > Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
> > > ---
> > > v2:
> > > - rephrase commit message
> > > 
> > >  Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml | 4 +++-
> > >  1 file changed, 3 insertions(+), 1 deletion(-)
> > > 
> > > diff --git a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> > > index eaedb4cc6b6c..7bd7bbbac9e0 100644
> > > --- a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> > > +++ b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
> > > @@ -11,7 +11,9 @@ maintainers:
> > >  
> > >  properties:
> > >    compatible:
> > > -    const: nxp,ptn5110
> > > +    enum:
> > > +      - nxp,ptn5110
> > > +      - tcpci
> > 
> > That's not a fallback, but enum. Fallback is "items" and then you could
> 
> Damn, you're right. Sorry.
> 
> > also send a follow-up patchset (separate, so Greg won't take it) fixing
> > DTS (if not, let me know, so I will fix it).
> 
> Sry. but I don't get this. Why do I need to send a follow-up? Greg did
> not apply anything, at least I didn't received an e-mail, that this
> patchset was picked.

Got it now and made it this way.

Regards,
  Marco

Re: [PATCH v2 1/4] dt-bindings: usb: typec-tcpci: add tcpci fallback binding

[Krzysztof Kozlowski]

On 22/02/2024 21:23, Marco Felsch wrote:
> On 24-02-22, Krzysztof Kozlowski wrote:
>> On 15/02/2024 22:28, Marco Felsch wrote:
>>> The NXP PTN5110 [1] is an TCPCI [2] compatible chip, so add the fallback
>>> binding.
>>>
>>> [1] https://www.nxp.com/docs/en/data-sheet/PTN5110.pdf
>>> [2] https://www.usb.org/sites/default/files/documents/usb-port_controller_specification_rev2.0_v1.0_0.pdf
>>>
>>> Signed-off-by: Marco Felsch <m.felsch@pengutronix.de>
>>> ---
>>> v2:
>>> - rephrase commit message
>>>
>>>  Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml | 4 +++-
>>>  1 file changed, 3 insertions(+), 1 deletion(-)
>>>
>>> diff --git a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
>>> index eaedb4cc6b6c..7bd7bbbac9e0 100644
>>> --- a/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
>>> +++ b/Documentation/devicetree/bindings/usb/nxp,ptn5110.yaml
>>> @@ -11,7 +11,9 @@ maintainers:
>>>  
>>>  properties:
>>>    compatible:
>>> -    const: nxp,ptn5110
>>> +    enum:
>>> +      - nxp,ptn5110
>>> +      - tcpci
>>
>> That's not a fallback, but enum. Fallback is "items" and then you could
> 
> Damn, you're right. Sorry.
> 
>> also send a follow-up patchset (separate, so Greg won't take it) fixing
>> DTS (if not, let me know, so I will fix it).
> 
> Sry. but I don't get this. Why do I need to send a follow-up? Greg did
> not apply anything, at least I didn't received an e-mail, that this
> patchset was picked.

If you change existing ptn5110 to a list of ptn5110+fallback, then all
existing will DTS start report warnings. Someone needs to fix this.

Best regards,
Krzysztof