Re: [PATCH v1 9/9] media: qcom: camss: Fix csid-gen2 for test pattern generator

[Konrad Dybcio <konrad.dybcio@linaro.org>]

On 22.08.2023 18:16, Bryan O'Donoghue wrote:
> From: Andrey Konovalov <andrey.konovalov@linaro.org>
> 
> In the current driver csid Test Pattern Generator (TPG) doesn't work.
> This change:
> - fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
> - fixes the shift by one between test_pattern control value and the
>   actual pattern.
> So that TPG starts working, but with the below limitations:
> - only test_pattern=9 works as it should
> - test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
> - the rest of test_pattern's don't work (yavta doesn't get the data)
> - regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
>   order is always the same (RGGB for any RAW8 or RAW10P format in
>   4608x2592 resolution).
> 
> Tested with:
> 
> RAW10P format, VC0:
>  media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
>  v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
>  yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0
> 
> RAW10P format, VC1:
>  media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
>  media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
>  v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
>  yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1
> 
> RAW8 format, VC0:
>  media-ctl --reset
>  media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
>  media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
>  media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
>  yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0
> 
> Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
> Cc: stable@vger.kernel.org
> Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
> Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
> ---
That's a whole lot to unroll..

[...]
>  		if (tg->enabled) {
> -			/* Config Test Generator */
> -			vc = 0xa;
> -
Which part does this hunk correlate to?

>  			/* configure one DT, infinite frames */
>  			val = vc << TPG_VC_CFG0_VC_NUM;
>  			val |= INTELEAVING_MODE_ONE_SHOT << TPG_VC_CFG0_LINE_INTERLEAVING_MODE;
> @@ -370,14 +367,14 @@ static void __csid_configure_stream(struct csid_device *csid, u8 enable, u8 vc)
>  
>  			writel_relaxed(0x12345678, csid->base + CSID_TPG_LFSR_SEED);
>  
> -			val = input_format->height & 0x1fff << TPG_DT_n_CFG_0_FRAME_HEIGHT;
> -			val |= input_format->width & 0x1fff << TPG_DT_n_CFG_0_FRAME_WIDTH;
> +			val = (input_format->height & 0x1fff) << TPG_DT_n_CFG_0_FRAME_HEIGHT;
> +			val |= (input_format->width & 0x1fff) << TPG_DT_n_CFG_0_FRAME_WIDTH;
>  			writel_relaxed(val, csid->base + CSID_TPG_DT_n_CFG_0(0));
This screams necessity for FIELD_PREP/GET! Could you please convert
it in another series if you have time for it?

Konrad