* POI: nvidia forcedeth phy id not present
[not found] <50243237.9040704@telenet.be>
@ 2012-08-09 23:14 ` Janpieter Sollie
2012-08-10 17:08 ` Janpieter Sollie
0 siblings, 1 reply; 2+ messages in thread
From: Janpieter Sollie @ 2012-08-09 23:14 UTC (permalink / raw)
To: linux-kernel
[-- Attachment #1: Type: text/plain, Size: 2352 bytes --]
guess this is not a real bug report, just some POI:
1. one-liner: the realtek 8211cl driver (PHY 0x732) is not present in the forcedeth.c driver
2. full description: my mainboard (Asus M4N82 deluxe) has an onboard nvidia/realtek 8211cl
ethernet card.
The forcedeth detects the card, but is unable to bring up the phy, disabling additional features
(MTU limited to 1500).
The card identifies itself as 'PHY OUI 0x732', which is not even present in the forcedeth driver.
I feel not yet capable of developing a patch for this, I'm right now learning about linux driver
structure
3: keywords: networking, driver, nvidia
4. kernel version: Linux version 3.2.23 ( root@vliegtuig) (gcc version 4.6.3 (Gentoo 4.6.3 p1.3,
pie-0.5.2) #1 SMP Sun Jul 29 19:35 CEST 2012
5: kernel messages: none
6: disabled features: mtu > 1500
7. Environment 7.1
7.1 Software: ifconfig, dmesg
7.2 Proc/cpuinfo:
>processor : 0 vendor_id : AuthenticAMD
>cpu family : 16
>model : 4
>model name : AMD Phenom(tm) II X4 920 Processor
>stepping : 2
>microcode : 0x1000086
>cpu MHz : 800.000
>cache size : 512 KB
>physical id : 0
>siblings : 4
>core id : 0
>cpu cores : 4
>apicid : 0
>initial apicid : 0
>fpu : yes
>fpu_exception : yes
>cpuid level : 5
>wp : yes
>flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush mmx
fxsr sse sse2 ht syscall nx mmxext fxsr_opt pdpe1gb rdtscp lm >3dnowext 3dnow constant_tsc
rep_good nopl nonstop_tsc extd_apicid pni monitor cx16 popcnt lahf_lm cmp_legacy svm extapic
cr8_legacy abm sse4a misalignsse >3dnowprefetch osvw ibs skinit wdt npt lbrv svm_lock nrip_save
bogomips : 6349.76 TLB size : 1024 4K pages clflush size : 64 cache_alignment : 64 address sizes
: 48 >bits physical, 48 bits virtual power management: ts ttp tm stc 100mhzsteps hwpstate
7.2 Module information: forcedeth 50715 0 - Live 0xffffffffa012d000
7.3 dmesg info: view attachments
7.4 IO information: view attachments
7.5 lspci: view attachments
8. PHY info: view http://www.rom.by/files/rtl8211cl_datasheet_1.3.pdf
The point of improvement is not disabling the driver itself. but it would unlock some features
highly appreciated.
If required, I'll develop some patch for this, but it may take some time before I guess I know
how the chip detection actually works.
kind regards,
Janpieter Sollie - janpieter.sollie@telenet.be
[-- Attachment #2: dmesg.log --]
[-- Type: text/plain, Size: 62709 bytes --]
ed greatest stack depth: 5872 bytes left
[ 0.334003] node 0 link 0: io port [1000, ffffff]
[ 0.334003] node 0 link 0: io port [1000, 1fff]
[ 0.334003] TOM: 0000000080000000 aka 2048M
[ 0.334003] Fam 10h mmconf [mem 0xe0000000-0xefffffff]
[ 0.334003] node 0 link 0: mmio [e0000000, efffffff] ==> none
[ 0.334003] node 0 link 0: mmio [a0000, bffff]
[ 0.334003] node 0 link 0: mmio [80000000, fe0bffff] ==> [80000000, dfffffff] and [f0000000, fe0bffff]
[ 0.334003] bus: [00, 07] on node 0 link 0
[ 0.334003] bus: 00 index 0 [io 0x0000-0xffff]
[ 0.334003] bus: 00 index 1 [mem 0x000a0000-0x000bffff]
[ 0.334003] bus: 00 index 2 [mem 0x80000000-0xdfffffff]
[ 0.334003] bus: 00 index 3 [mem 0xf0000000-0xfcffffffff]
[ 0.334003] Extended Config Space enabled on 1 nodes
[ 0.334003] ACPI: bus type pci registered
[ 0.334003] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.334003] PCI: not using MMCONFIG
[ 0.334003] PCI: Using configuration type 1 for base access
[ 0.336647] PCI: Using configuration type 1 for extended access
[ 0.340057] bio: create slab <bio-0> at 0
[ 0.340190] ACPI: Added _OSI(Module Device)
[ 0.340190] ACPI: Added _OSI(Processor Device)
[ 0.340263] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.340399] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.341428] ACPI: EC: Look up EC in DSDT
[ 0.341428] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.400181] ACPI: Interpreter enabled
[ 0.400316] ACPI: (supports S0 S1 S3 S5)
[ 0.400596] ACPI: Using IOAPIC for interrupt routing
[ 0.400747] PCI: MMCONFIG for domain 0000 [bus 00-ff] at [mem 0xe0000000-0xefffffff] (base 0xe0000000)
[ 0.401554] PCI: MMCONFIG at [mem 0xe0000000-0xefffffff] reserved in ACPI motherboard resources
[ 0.423360] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.423682] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-ff])
[ 0.423885] pci_root PNP0A03:00: host bridge window [io 0x0000-0x0cf7]
[ 0.423885] pci_root PNP0A03:00: host bridge window [io 0x0d00-0xffff]
[ 0.423885] pci_root PNP0A03:00: host bridge window [mem 0x000a0000-0x000bffff]
[ 0.423922] pci_root PNP0A03:00: host bridge window [mem 0x000d0000-0x000dffff]
[ 0.424151] pci_root PNP0A03:00: host bridge window [mem 0x80000000-0xdfffffff]
[ 0.424380] pci_root PNP0A03:00: host bridge window [mem 0xf0000000-0xfebfffff]
[ 0.424643] pci 0000:00:00.0: [10de:0754] type 0 class 0x000500
[ 0.424893] pci 0000:00:01.0: [10de:075d] type 0 class 0x000601
[ 0.424899] pci 0000:00:01.0: reg 10: [io 0x0900-0x09ff]
[ 0.424930] pci 0000:00:01.1: [10de:0752] type 0 class 0x000c05
[ 0.424940] pci 0000:00:01.1: reg 10: [io 0x0e00-0x0e3f]
[ 0.424953] pci 0000:00:01.1: reg 20: [io 0x0600-0x063f]
[ 0.424958] pci 0000:00:01.1: reg 24: [io 0x0700-0x073f]
[ 0.424985] pci 0000:00:01.1: PME# supported from D3hot D3cold
[ 0.424990] pci 0000:00:01.1: PME# disabled
[ 0.424998] pci 0000:00:01.2: [10de:0751] type 0 class 0x000500
[ 0.425040] pci 0000:00:01.3: [10de:0753] type 0 class 0x000b40
[ 0.425055] pci 0000:00:01.3: reg 10: [mem 0xdff80000-0xdfffffff]
[ 0.425055] pci 0000:00:01.4: [10de:0568] type 0 class 0x000500
[ 0.425055] pci 0000:00:02.0: [10de:077b] type 0 class 0x000c03
[ 0.425055] pci 0000:00:02.0: reg 10: [mem 0xdff7e000-0xdff7efff]
[ 0.425055] pci 0000:00:02.0: supports D1 D2
[ 0.425055] pci 0000:00:02.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:02.0: PME# disabled
[ 0.425055] pci 0000:00:02.1: [10de:077c] type 0 class 0x000c03
[ 0.425055] pci 0000:00:02.1: reg 10: [mem 0xdff7fc00-0xdff7fcff]
[ 0.425055] pci 0000:00:02.1: supports D1 D2
[ 0.425055] pci 0000:00:02.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:02.1: PME# disabled
[ 0.425055] pci 0000:00:04.0: [10de:077d] type 0 class 0x000c03
[ 0.425055] pci 0000:00:04.0: reg 10: [mem 0xdff7d000-0xdff7dfff]
[ 0.425055] pci 0000:00:04.0: supports D1 D2
[ 0.425055] pci 0000:00:04.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:04.0: PME# disabled
[ 0.425055] pci 0000:00:04.1: [10de:077e] type 0 class 0x000c03
[ 0.425055] pci 0000:00:04.1: reg 10: [mem 0xdff7f800-0xdff7f8ff]
[ 0.425055] pci 0000:00:04.1: supports D1 D2
[ 0.425055] pci 0000:00:04.1: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:04.1: PME# disabled
[ 0.425055] pci 0000:00:06.0: [10de:0759] type 0 class 0x000101
[ 0.425055] pci 0000:00:06.0: reg 20: [io 0xffa0-0xffaf]
[ 0.425055] pci 0000:00:07.0: [10de:0774] type 0 class 0x000403
[ 0.425055] pci 0000:00:07.0: reg 10: [mem 0xdff78000-0xdff7bfff]
[ 0.425055] pci 0000:00:07.0: PME# supported from D3hot D3cold
[ 0.425055] pci 0000:00:07.0: PME# disabled
[ 0.425055] pci 0000:00:08.0: [10de:075a] type 1 class 0x000604
[ 0.425055] pci 0000:00:09.0: [10de:0ad4] type 0 class 0x000106
[ 0.425055] pci 0000:00:09.0: reg 10: [io 0xb080-0xb087]
[ 0.425055] pci 0000:00:09.0: reg 14: [io 0xb000-0xb003]
[ 0.425055] pci 0000:00:09.0: reg 18: [io 0xac00-0xac07]
[ 0.425055] pci 0000:00:09.0: reg 1c: [io 0xa880-0xa883]
[ 0.425055] pci 0000:00:09.0: reg 20: [io 0xa800-0xa80f]
[ 0.425055] pci 0000:00:09.0: reg 24: [mem 0xdff76000-0xdff77fff]
[ 0.425055] pci 0000:00:0a.0: [10de:0760] type 0 class 0x000200
[ 0.425055] pci 0000:00:0a.0: reg 10: [mem 0xdff7c000-0xdff7cfff]
[ 0.425055] pci 0000:00:0a.0: reg 14: [io 0xa480-0xa487]
[ 0.425055] pci 0000:00:0a.0: reg 18: [mem 0xdff7f400-0xdff7f4ff]
[ 0.425055] pci 0000:00:0a.0: reg 1c: [mem 0xdff7f000-0xdff7f00f]
[ 0.425055] pci 0000:00:0a.0: supports D1 D2
[ 0.425055] pci 0000:00:0a.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:0a.0: PME# disabled
[ 0.425055] pci 0000:00:10.0: [10de:0778] type 1 class 0x000604
[ 0.425055] pci 0000:00:10.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:10.0: PME# disabled
[ 0.425055] pci 0000:00:13.0: [10de:077a] type 1 class 0x000604
[ 0.425055] pci 0000:00:13.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:13.0: PME# disabled
[ 0.425055] pci 0000:00:14.0: [10de:077a] type 1 class 0x000604
[ 0.425055] pci 0000:00:14.0: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.425055] pci 0000:00:14.0: PME# disabled
[ 0.425055] pci 0000:00:18.0: [1022:1200] type 0 class 0x000600
[ 0.425055] pci 0000:00:18.1: [1022:1201] type 0 class 0x000600
[ 0.425055] pci 0000:00:18.2: [1022:1202] type 0 class 0x000600
[ 0.425055] pci 0000:00:18.3: [1022:1203] type 0 class 0x000600
[ 0.425055] pci 0000:00:18.4: [1022:1204] type 0 class 0x000600
[ 0.425055] pci 0000:00:08.0: PCI bridge to [bus 01-01] (subtractive decode)
[ 0.425055] pci 0000:00:08.0: bridge window [io 0x0000-0x0cf7] (subtractive decode)
[ 0.425055] pci 0000:00:08.0: bridge window [io 0x0d00-0xffff] (subtractive decode)
[ 0.425055] pci 0000:00:08.0: bridge window [mem 0x000a0000-0x000bffff] (subtractive decode)
[ 0.425055] pci 0000:00:08.0: bridge window [mem 0x000d0000-0x000dffff] (subtractive decode)
[ 0.425055] pci 0000:00:08.0: bridge window [mem 0x80000000-0xdfffffff] (subtractive decode)
[ 0.425055] pci 0000:00:08.0: bridge window [mem 0xf0000000-0xfebfffff] (subtractive decode)
[ 0.425200] pci 0000:02:00.0: [10de:05b1] type 1 class 0x000604
[ 0.425234] pci 0000:02:00.0: PME# supported from D0 D3hot D3cold
[ 0.425237] pci 0000:02:00.0: PME# disabled
[ 0.425856] pci 0000:00:10.0: PCI bridge to [bus 02-06]
[ 0.426005] pci 0000:00:10.0: bridge window [io 0xc000-0xefff]
[ 0.426012] pci 0000:00:10.0: bridge window [mem 0xf0000000-0xfbffffff]
[ 0.426025] pci 0000:00:10.0: bridge window [mem 0x90000000-0xcfffffff 64bit pref]
[ 0.426049] pci 0000:03:00.0: [10de:05b1] type 1 class 0x000604
[ 0.426080] pci 0000:03:00.0: PME# supported from D0 D3hot D3cold
[ 0.426082] pci 0000:03:00.0: PME# disabled
[ 0.426094] pci 0000:03:02.0: [10de:05b1] type 1 class 0x000604
[ 0.426124] pci 0000:03:02.0: PME# supported from D0 D3hot D3cold
[ 0.426126] pci 0000:03:02.0: PME# disabled
[ 0.426138] pci 0000:03:03.0: [10de:05b1] type 1 class 0x000604
[ 0.426168] pci 0000:03:03.0: PME# supported from D0 D3hot D3cold
[ 0.426170] pci 0000:03:03.0: PME# disabled
[ 0.426189] pci 0000:02:00.0: PCI bridge to [bus 03-06]
[ 0.426330] pci 0000:02:00.0: bridge window [io 0xc000-0xefff]
[ 0.426332] pci 0000:02:00.0: bridge window [mem 0xf0000000-0xfbffffff]
[ 0.426336] pci 0000:02:00.0: bridge window [mem 0x90000000-0xcfffffff 64bit pref]
[ 0.426361] pci 0000:04:00.0: [10de:0193] type 0 class 0x000300
[ 0.426370] pci 0000:04:00.0: reg 10: [mem 0xf3000000-0xf3ffffff]
[ 0.426380] pci 0000:04:00.0: reg 14: [mem 0x90000000-0x9fffffff 64bit pref]
[ 0.426389] pci 0000:04:00.0: reg 1c: [mem 0xf0000000-0xf1ffffff 64bit]
[ 0.426396] pci 0000:04:00.0: reg 24: [io 0xcc00-0xcc7f]
[ 0.426402] pci 0000:04:00.0: reg 30: [mem 0xf2fe0000-0xf2ffffff pref]
[ 0.426440] pci 0000:04:00.0: disabling ASPM on pre-1.1 PCIe device. You can enable it with 'pcie_aspm=force'
[ 0.429977] pci 0000:03:00.0: PCI bridge to [bus 04-04]
[ 0.430118] pci 0000:03:00.0: bridge window [io 0xc000-0xcfff]
[ 0.430120] pci 0000:03:00.0: bridge window [mem 0xf0000000-0xf3ffffff]
[ 0.430124] pci 0000:03:00.0: bridge window [mem 0x90000000-0x9fffffff 64bit pref]
[ 0.430151] pci 0000:05:00.0: [10de:0640] type 0 class 0x000300
[ 0.430160] pci 0000:05:00.0: reg 10: [mem 0xf7000000-0xf7ffffff]
[ 0.430170] pci 0000:05:00.0: reg 14: [mem 0xa0000000-0xbfffffff 64bit pref]
[ 0.430180] pci 0000:05:00.0: reg 1c: [mem 0xf4000000-0xf5ffffff 64bit]
[ 0.430187] pci 0000:05:00.0: reg 24: [io 0xdc00-0xdc7f]
[ 0.430193] pci 0000:05:00.0: reg 30: [mem 0xf6f80000-0xf6ffffff pref]
[ 0.436646] pci 0000:03:02.0: PCI bridge to [bus 05-05]
[ 0.436787] pci 0000:03:02.0: bridge window [io 0xd000-0xdfff]
[ 0.436789] pci 0000:03:02.0: bridge window [mem 0xf4000000-0xf7ffffff]
[ 0.436792] pci 0000:03:02.0: bridge window [mem 0xa0000000-0xbfffffff 64bit pref]
[ 0.436821] pci 0000:06:00.0: [10de:0611] type 0 class 0x000300
[ 0.436830] pci 0000:06:00.0: reg 10: [mem 0xfb000000-0xfbffffff]
[ 0.436840] pci 0000:06:00.0: reg 14: [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.436850] pci 0000:06:00.0: reg 1c: [mem 0xf8000000-0xf9ffffff 64bit]
[ 0.436857] pci 0000:06:00.0: reg 24: [io 0xec00-0xec7f]
[ 0.436864] pci 0000:06:00.0: reg 30: [mem 0xfafe0000-0xfaffffff pref]
[ 0.443311] pci 0000:03:03.0: PCI bridge to [bus 06-06]
[ 0.443452] pci 0000:03:03.0: bridge window [io 0xe000-0xefff]
[ 0.443454] pci 0000:03:03.0: bridge window [mem 0xf8000000-0xfbffffff]
[ 0.443457] pci 0000:03:03.0: bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.443614] pci 0000:00:13.0: PCI bridge to [bus 07-07]
[ 0.443925] pci 0000:00:14.0: PCI bridge to [bus 08-08]
[ 0.444127] pci_bus 0000:00: on NUMA node 0
[ 0.444129] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.444258] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.444294] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0._PRT]
[ 0.444313] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0.BR20._PRT]
[ 0.444359] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0.BR20.BR21._PRT]
[ 0.444382] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0.BR20.BR23._PRT]
[ 0.444402] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.MXR0.BR20.BR24._PRT]
[ 0.444422] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR13._PRT]
[ 0.444440] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.BR14._PRT]
[ 0.444521] pci0000:00: Requesting ACPI _OSC control (0x1d)
[ 0.444771] pci0000:00: ACPI _OSC request failed (AE_SUPPORT), returned control mask: 0x0c
[ 0.445004] ACPI _OSC control for PCIe not granted, disabling ASPM
[ 0.453528] ACPI: PCI Interrupt Link [LNKA] (IRQs 16 17 18 19) *0, disabled.
[ 0.453842] ACPI: PCI Interrupt Link [LNKB] (IRQs 16 17 18 19) *0, disabled.
[ 0.454318] ACPI: PCI Interrupt Link [LNKC] (IRQs 16 17 18 19) *0, disabled.
[ 0.454793] ACPI: PCI Interrupt Link [LNKD] (IRQs 16 17 18 19) *0, disabled.
[ 0.456692] ACPI: PCI Interrupt Link [LN0A] (IRQs 16 17 18 19) *10
[ 0.457128] ACPI: PCI Interrupt Link [LN0B] (IRQs 16 17 18 19) *0, disabled.
[ 0.457605] ACPI: PCI Interrupt Link [LN0C] (IRQs 16 17 18 19) *10
[ 0.458042] ACPI: PCI Interrupt Link [LN0D] (IRQs 16 17 18 19) *10
[ 0.458042] ACPI: PCI Interrupt Link [LN1A] (IRQs 16 17 18 19) *0, disabled.
[ 0.458042] ACPI: PCI Interrupt Link [LN1B] (IRQs 16 17 18 19) *0, disabled.
[ 0.458042] ACPI: PCI Interrupt Link [LN1C] (IRQs 16 17 18 19) *0, disabled.
[ 0.458112] ACPI: PCI Interrupt Link [LN1D] (IRQs 16 17 18 19) *0, disabled.
[ 0.458586] ACPI: PCI Interrupt Link [LN2A] (IRQs 16 17 18 19) *0, disabled.
[ 0.459062] ACPI: PCI Interrupt Link [LN2B] (IRQs 16 17 18 19) *0, disabled.
[ 0.459536] ACPI: PCI Interrupt Link [LN2C] (IRQs 16 17 18 19) *0, disabled.
[ 0.460020] ACPI: PCI Interrupt Link [LN2D] (IRQs 16 17 18 19) *0, disabled.
[ 0.460496] ACPI: PCI Interrupt Link [LN3A] (IRQs 16 17 18 19) *11
[ 0.460932] ACPI: PCI Interrupt Link [LN3B] (IRQs 16 17 18 19) *0, disabled.
[ 0.461407] ACPI: PCI Interrupt Link [LN3C] (IRQs 16 17 18 19) *0, disabled.
[ 0.461882] ACPI: PCI Interrupt Link [LN3D] (IRQs 16 17 18 19) *0, disabled.
[ 0.462360] ACPI: PCI Interrupt Link [LN4A] (IRQs 16 17 18 19) *15
[ 0.462797] ACPI: PCI Interrupt Link [LN4B] (IRQs 16 17 18 19) *0, disabled.
[ 0.463271] ACPI: PCI Interrupt Link [LN4C] (IRQs 16 17 18 19) *0, disabled.
[ 0.467057] ACPI: PCI Interrupt Link [LN4D] (IRQs 16 17 18 19) *0, disabled.
[ 0.467532] ACPI: PCI Interrupt Link [LN5A] (IRQs 16 17 18 19) *0, disabled.
[ 0.468007] ACPI: PCI Interrupt Link [LN5B] (IRQs 16 17 18 19) *0, disabled.
[ 0.468481] ACPI: PCI Interrupt Link [LN5C] (IRQs 16 17 18 19) *0, disabled.
[ 0.468956] ACPI: PCI Interrupt Link [LN5D] (IRQs 16 17 18 19) *0, disabled.
[ 0.469431] ACPI: PCI Interrupt Link [LN6A] (IRQs 16 17 18 19) *0, disabled.
[ 0.469906] ACPI: PCI Interrupt Link [LN6B] (IRQs 16 17 18 19) *0, disabled.
[ 0.470390] ACPI: PCI Interrupt Link [LN6C] (IRQs 16 17 18 19) *0, disabled.
[ 0.470865] ACPI: PCI Interrupt Link [LN6D] (IRQs 16 17 18 19) *0, disabled.
[ 0.471340] ACPI: PCI Interrupt Link [LN7A] (IRQs 16 17 18 19) *0, disabled.
[ 0.471815] ACPI: PCI Interrupt Link [LN7B] (IRQs 16 17 18 19) *0, disabled.
[ 0.472290] ACPI: PCI Interrupt Link [LN7C] (IRQs 16 17 18 19) *0, disabled.
[ 0.472764] ACPI: PCI Interrupt Link [LN7D] (IRQs 16 17 18 19) *0, disabled.
[ 0.473240] ACPI: PCI Interrupt Link [LUB0] (IRQs 20 21 22 23) *15
[ 0.473687] ACPI: PCI Interrupt Link [LUB2] (IRQs 20 21 22 23) *11
[ 0.474124] ACPI: PCI Interrupt Link [LMAC] (IRQs 20 21 22 23) *15
[ 0.474561] ACPI: PCI Interrupt Link [LAZA] (IRQs 20 21 22 23) *11
[ 0.474997] ACPI: PCI Interrupt Link [SGRU] (IRQs 20 21 22 23) *0, disabled.
[ 0.475474] ACPI: PCI Interrupt Link [LSMB] (IRQs 20 21 22 23) *10
[ 0.475912] ACPI: PCI Interrupt Link [LPMU] (IRQs 20 21 22 23) *7
[ 0.476352] ACPI: PCI Interrupt Link [LSA0] (IRQs 20 21 22 23) *5
[ 0.476814] ACPI: PCI Interrupt Link [LATA] (IRQs 20 21 22 23) *0, disabled.
[ 0.477291] ACPI: PCI Interrupt Link [UB11] (IRQs 20 21 22 23) *10
[ 0.477729] ACPI: PCI Interrupt Link [UB12] (IRQs 20 21 22 23) *10
[ 0.478164] vgaarb: device added: PCI:0000:04:00.0,decodes=io+mem,owns=io+mem,locks=none
[ 0.478164] vgaarb: device added: PCI:0000:05:00.0,decodes=io+mem,owns=none,locks=none
[ 0.478164] vgaarb: device added: PCI:0000:06:00.0,decodes=io+mem,owns=none,locks=none
[ 0.478164] vgaarb: loaded
[ 0.478164] vgaarb: bridge control possible 0000:06:00.0
[ 0.478164] vgaarb: bridge control possible 0000:05:00.0
[ 0.478164] vgaarb: bridge control possible 0000:04:00.0
[ 0.478164] SCSI subsystem initialized
[ 0.478164] libata version 3.00 loaded.
[ 0.479995] usbcore: registered new interface driver usbfs
[ 0.480131] usbcore: registered new interface driver hub
[ 0.480131] usbcore: registered new device driver usb
[ 0.480131] Advanced Linux Sound Architecture Driver Version 1.0.24.
[ 0.480131] PCI: Using ACPI for IRQ routing
[ 0.483537] PCI: pci_cache_line_size set to 64 bytes
[ 0.483609] reserve RAM buffer: 000000000009fc00 - 000000000009ffff
[ 0.483611] reserve RAM buffer: 000000007ff90000 - 000000007fffffff
[ 0.486683] NetLabel: Initializing
[ 0.486779] NetLabel: domain hash size = 128
[ 0.486913] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.487057] NetLabel: unlabeled traffic allowed by default
[ 0.487199] HPET: 3 timers in total, 0 timers will be used for per-cpu timer
[ 0.487349] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 31
[ 0.487626] hpet0: 3 comparators, 32-bit 25.000000 MHz counter
[ 0.503332] Switching to clocksource hpet
[ 0.505586] pnp: PnP ACPI init
[ 0.505604] ACPI: bus type pnp registered
[ 0.505812] pnp 00:00: [bus 00-ff]
[ 0.505814] pnp 00:00: [io 0x0cf8-0x0cff]
[ 0.505816] pnp 00:00: [io 0x0000-0x0cf7 window]
[ 0.505817] pnp 00:00: [io 0x0d00-0xffff window]
[ 0.505819] pnp 00:00: [mem 0x000a0000-0x000bffff window]
[ 0.505820] pnp 00:00: [mem 0x000d0000-0x000dffff window]
[ 0.505821] pnp 00:00: [mem 0x80000000-0xdfffffff window]
[ 0.505822] pnp 00:00: [mem 0xf0000000-0xfebfffff window]
[ 0.505927] pnp 00:00: Plug and Play ACPI device, IDs PNP0a03 (active)
[ 0.505946] pnp 00:01: [dma 4]
[ 0.505947] pnp 00:01: [io 0x0000-0x000f]
[ 0.505949] pnp 00:01: [io 0x0081-0x0083]
[ 0.505950] pnp 00:01: [io 0x0087]
[ 0.505951] pnp 00:01: [io 0x0089-0x008b]
[ 0.505952] pnp 00:01: [io 0x008f]
[ 0.505953] pnp 00:01: [io 0x00c0-0x00df]
[ 0.505994] pnp 00:01: Plug and Play ACPI device, IDs PNP0200 (active)
[ 0.505999] pnp 00:02: [io 0x0061]
[ 0.506038] pnp 00:02: Plug and Play ACPI device, IDs PNP0800 (active)
[ 0.506043] pnp 00:03: [io 0x00f0-0x00ff]
[ 0.506053] pnp 00:03: [irq 13]
[ 0.506092] pnp 00:03: Plug and Play ACPI device, IDs PNP0c04 (active)
[ 0.506295] pnp 00:04: [mem 0x000d0000-0x000d3fff window]
[ 0.506296] pnp 00:04: [mem 0x000d4000-0x000d7fff window]
[ 0.506297] pnp 00:04: [mem 0x000de000-0x000dffff window]
[ 0.506299] pnp 00:04: [io 0x0010-0x001f]
[ 0.506300] pnp 00:04: [io 0x0022-0x003f]
[ 0.506301] pnp 00:04: [io 0x0044-0x004d]
[ 0.506302] pnp 00:04: [io 0x0050-0x005f]
[ 0.506303] pnp 00:04: [io 0x0062-0x0063]
[ 0.506304] pnp 00:04: [io 0x0065-0x006f]
[ 0.506305] pnp 00:04: [io 0x0072-0x007f]
[ 0.506306] pnp 00:04: [io 0x0080]
[ 0.506307] pnp 00:04: [io 0x0084-0x0086]
[ 0.506308] pnp 00:04: [io 0x0088]
[ 0.506309] pnp 00:04: [io 0x008c-0x008e]
[ 0.506310] pnp 00:04: [io 0x0090-0x009f]
[ 0.506312] pnp 00:04: [io 0x00a2-0x00bf]
[ 0.506313] pnp 00:04: [io 0x00e0-0x00ef]
[ 0.506314] pnp 00:04: [io 0x04d0-0x04d1]
[ 0.506315] pnp 00:04: [io 0x0800-0x080f]
[ 0.506316] pnp 00:04: [io 0x0500-0x057f]
[ 0.506317] pnp 00:04: [io 0x0580-0x05ff]
[ 0.506318] pnp 00:04: [io 0x0800-0x087f]
[ 0.506319] pnp 00:04: [io 0x0880-0x08ff]
[ 0.506321] pnp 00:04: [io 0x0d00-0x0d7f]
[ 0.506322] pnp 00:04: [io 0x0d80-0x0dff]
[ 0.506324] pnp 00:04: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.506325] pnp 00:04: [mem 0x00000000-0xffffffffffffffff disabled]
[ 0.506326] pnp 00:04: [mem 0xfed04000-0xfed04fff]
[ 0.506328] pnp 00:04: [mem 0xfee01000-0xfeefffff]
[ 0.506423] system 00:04: [io 0x04d0-0x04d1] has been reserved
[ 0.506565] system 00:04: [io 0x0800-0x080f] has been reserved
[ 0.506736] system 00:04: [io 0x0500-0x057f] has been reserved
[ 0.506879] system 00:04: [io 0x0580-0x05ff] has been reserved
[ 0.507021] system 00:04: [io 0x0800-0x087f] could not be reserved
[ 0.507164] system 00:04: [io 0x0880-0x08ff] has been reserved
[ 0.507306] system 00:04: [io 0x0d00-0x0d7f] has been reserved
[ 0.507448] system 00:04: [io 0x0d80-0x0dff] has been reserved
[ 0.507590] system 00:04: [mem 0x000d0000-0x000d3fff window] has been reserved
[ 0.507818] system 00:04: [mem 0x000d4000-0x000d7fff window] has been reserved
[ 0.508047] system 00:04: [mem 0x000de000-0x000dffff window] has been reserved
[ 0.508277] system 00:04: [mem 0xfed04000-0xfed04fff] has been reserved
[ 0.508422] system 00:04: [mem 0xfee01000-0xfeefffff] has been reserved
[ 0.508567] system 00:04: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.508634] pnp 00:05: [mem 0xfed00000-0xfed00fff]
[ 0.508636] pnp 00:05: [irq 2 disabled]
[ 0.508642] pnp 00:05: [irq 8]
[ 0.508723] pnp 00:05: Plug and Play ACPI device, IDs PNP0103 (active)
[ 0.508737] pnp 00:06: [io 0x0070-0x0071]
[ 0.508788] pnp 00:06: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.508834] pnp 00:07: [mem 0xfec00000-0xfec00fff]
[ 0.508835] pnp 00:07: [mem 0xfee00000-0xfee00fff]
[ 0.508897] system 00:07: [mem 0xfec00000-0xfec00fff] could not be reserved
[ 0.509044] system 00:07: [mem 0xfee00000-0xfee00fff] has been reserved
[ 0.509189] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.509205] pnp 00:08: [io 0x0060]
[ 0.509207] pnp 00:08: [io 0x0064]
[ 0.509213] pnp 00:08: [irq 1]
[ 0.509269] pnp 00:08: Plug and Play ACPI device, IDs PNP0303 PNP030b (active)
[ 0.509379] pnp 00:09: [io 0x0000-0xffffffffffffffff disabled]
[ 0.509380] pnp 00:09: [io 0x0230-0x023f]
[ 0.509381] pnp 00:09: [io 0x0290-0x029f]
[ 0.509382] pnp 00:09: [io 0x0a00-0x0a0f]
[ 0.509383] pnp 00:09: [io 0x0a10-0x0a1f]
[ 0.509446] system 00:09: [io 0x0230-0x023f] has been reserved
[ 0.509588] system 00:09: [io 0x0290-0x029f] has been reserved
[ 0.509730] system 00:09: [io 0x0a00-0x0a0f] has been reserved
[ 0.509872] system 00:09: [io 0x0a10-0x0a1f] has been reserved
[ 0.510031] system 00:09: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.510216] pnp 00:0a: [mem 0xe0000000-0xefffffff]
[ 0.510294] system 00:0a: [mem 0xe0000000-0xefffffff] has been reserved
[ 0.510440] system 00:0a: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.510531] pnp 00:0b: [mem 0x00000000-0x0009ffff]
[ 0.510533] pnp 00:0b: [mem 0x000c0000-0x000cffff]
[ 0.510534] pnp 00:0b: [mem 0x000e0000-0x000fffff]
[ 0.510535] pnp 00:0b: [mem 0x00100000-0x7fffffff]
[ 0.510536] pnp 00:0b: [mem 0xfec00000-0xffffffff]
[ 0.510606] system 00:0b: [mem 0x00000000-0x0009ffff] could not be reserved
[ 0.510753] system 00:0b: [mem 0x000c0000-0x000cffff] could not be reserved
[ 0.510899] system 00:0b: [mem 0x000e0000-0x000fffff] could not be reserved
[ 0.511045] system 00:0b: [mem 0x00100000-0x7fffffff] could not be reserved
[ 0.511192] system 00:0b: [mem 0xfec00000-0xffffffff] could not be reserved
[ 0.511338] system 00:0b: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.511712] pnp: PnP ACPI: found 12 devices
[ 0.511846] ACPI: ACPI bus type pnp unregistered
[ 0.521429] PCI: max bus depth: 3 pci_try_num: 4
[ 0.521498] pci 0000:00:08.0: PCI bridge to [bus 01-01]
[ 0.521642] pci 0000:03:00.0: PCI bridge to [bus 04-04]
[ 0.521781] pci 0000:03:00.0: bridge window [io 0xc000-0xcfff]
[ 0.521925] pci 0000:03:00.0: bridge window [mem 0xf0000000-0xf3ffffff]
[ 0.522072] pci 0000:03:00.0: bridge window [mem 0x90000000-0x9fffffff 64bit pref]
[ 0.522305] pci 0000:03:02.0: PCI bridge to [bus 05-05]
[ 0.522444] pci 0000:03:02.0: bridge window [io 0xd000-0xdfff]
[ 0.522587] pci 0000:03:02.0: bridge window [mem 0xf4000000-0xf7ffffff]
[ 0.522734] pci 0000:03:02.0: bridge window [mem 0xa0000000-0xbfffffff 64bit pref]
[ 0.522967] pci 0000:03:03.0: PCI bridge to [bus 06-06]
[ 0.523107] pci 0000:03:03.0: bridge window [io 0xe000-0xefff]
[ 0.523250] pci 0000:03:03.0: bridge window [mem 0xf8000000-0xfbffffff]
[ 0.523426] pci 0000:03:03.0: bridge window [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.523659] pci 0000:02:00.0: PCI bridge to [bus 03-06]
[ 0.523798] pci 0000:02:00.0: bridge window [io 0xc000-0xefff]
[ 0.523942] pci 0000:02:00.0: bridge window [mem 0xf0000000-0xfbffffff]
[ 0.524089] pci 0000:02:00.0: bridge window [mem 0x90000000-0xcfffffff 64bit pref]
[ 0.524322] pci 0000:00:10.0: PCI bridge to [bus 02-06]
[ 0.524463] pci 0000:00:10.0: bridge window [io 0xc000-0xefff]
[ 0.524612] pci 0000:00:10.0: bridge window [mem 0xf0000000-0xfbffffff]
[ 0.524763] pci 0000:00:10.0: bridge window [mem 0x90000000-0xcfffffff 64bit pref]
[ 0.525003] pci 0000:00:13.0: PCI bridge to [bus 07-07]
[ 0.525164] pci 0000:00:14.0: PCI bridge to [bus 08-08]
[ 0.525328] pci 0000:00:08.0: setting latency timer to 64
[ 0.525437] ACPI: PCI Interrupt Link [LN0A] enabled at IRQ 19
[ 0.525587] pci 0000:00:10.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19
[ 0.525824] pci 0000:00:10.0: setting latency timer to 64
[ 0.525830] pci 0000:02:00.0: setting latency timer to 64
[ 0.525834] pci 0000:03:00.0: setting latency timer to 64
[ 0.525838] pci 0000:03:02.0: setting latency timer to 64
[ 0.525842] pci 0000:03:03.0: setting latency timer to 64
[ 0.525936] ACPI: PCI Interrupt Link [LN3A] enabled at IRQ 18
[ 0.526083] pci 0000:00:13.0: PCI INT A -> Link[LN3A] -> GSI 18 (level, low) -> IRQ 18
[ 0.526320] pci 0000:00:13.0: setting latency timer to 64
[ 0.526412] ACPI: PCI Interrupt Link [LN4A] enabled at IRQ 17
[ 0.526559] pci 0000:00:14.0: PCI INT A -> Link[LN4A] -> GSI 17 (level, low) -> IRQ 17
[ 0.526832] pci 0000:00:14.0: setting latency timer to 64
[ 0.526837] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7]
[ 0.526838] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff]
[ 0.526840] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.526841] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.526843] pci_bus 0000:00: resource 8 [mem 0x80000000-0xdfffffff]
[ 0.526844] pci_bus 0000:00: resource 9 [mem 0xf0000000-0xfebfffff]
[ 0.526846] pci_bus 0000:01: resource 4 [io 0x0000-0x0cf7]
[ 0.526847] pci_bus 0000:01: resource 5 [io 0x0d00-0xffff]
[ 0.526848] pci_bus 0000:01: resource 6 [mem 0x000a0000-0x000bffff]
[ 0.526850] pci_bus 0000:01: resource 7 [mem 0x000d0000-0x000dffff]
[ 0.526851] pci_bus 0000:01: resource 8 [mem 0x80000000-0xdfffffff]
[ 0.526853] pci_bus 0000:01: resource 9 [mem 0xf0000000-0xfebfffff]
[ 0.526854] pci_bus 0000:02: resource 0 [io 0xc000-0xefff]
[ 0.526856] pci_bus 0000:02: resource 1 [mem 0xf0000000-0xfbffffff]
[ 0.526857] pci_bus 0000:02: resource 2 [mem 0x90000000-0xcfffffff 64bit pref]
[ 0.526859] pci_bus 0000:03: resource 0 [io 0xc000-0xefff]
[ 0.526860] pci_bus 0000:03: resource 1 [mem 0xf0000000-0xfbffffff]
[ 0.526862] pci_bus 0000:03: resource 2 [mem 0x90000000-0xcfffffff 64bit pref]
[ 0.526863] pci_bus 0000:04: resource 0 [io 0xc000-0xcfff]
[ 0.526864] pci_bus 0000:04: resource 1 [mem 0xf0000000-0xf3ffffff]
[ 0.526866] pci_bus 0000:04: resource 2 [mem 0x90000000-0x9fffffff 64bit pref]
[ 0.526868] pci_bus 0000:05: resource 0 [io 0xd000-0xdfff]
[ 0.526869] pci_bus 0000:05: resource 1 [mem 0xf4000000-0xf7ffffff]
[ 0.526870] pci_bus 0000:05: resource 2 [mem 0xa0000000-0xbfffffff 64bit pref]
[ 0.526872] pci_bus 0000:06: resource 0 [io 0xe000-0xefff]
[ 0.526873] pci_bus 0000:06: resource 1 [mem 0xf8000000-0xfbffffff]
[ 0.526875] pci_bus 0000:06: resource 2 [mem 0xc0000000-0xcfffffff 64bit pref]
[ 0.526897] NET: Registered protocol family 2
[ 0.527065] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.527430] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.528591] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.528977] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.529122] TCP reno registered
[ 0.529252] UDP hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.529405] UDP-Lite hash table entries: 1024 (order: 3, 32768 bytes)
[ 0.529602] NET: Registered protocol family 1
[ 0.529839] RPC: Registered named UNIX socket transport module.
[ 0.529983] RPC: Registered udp transport module.
[ 0.530145] RPC: Registered tcp transport module.
[ 0.530281] RPC: Registered tcp NFSv4.1 backchannel transport module.
[ 0.530589] ACPI: PCI Interrupt Link [LUB0] enabled at IRQ 23
[ 0.530740] pci 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23 (level, low) -> IRQ 23
[ 0.616945] pci 0000:00:02.0: PCI INT A disabled
[ 0.617207] ACPI: PCI Interrupt Link [LUB2] enabled at IRQ 22
[ 0.617357] pci 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
[ 0.617598] pci 0000:00:02.1: PCI INT B disabled
[ 0.617824] ACPI: PCI Interrupt Link [UB11] enabled at IRQ 21
[ 0.617971] pci 0000:00:04.0: PCI INT A -> Link[UB11] -> GSI 21 (level, low) -> IRQ 21
[ 0.683604] pci 0000:00:04.0: PCI INT A disabled
[ 0.683860] ACPI: PCI Interrupt Link [UB12] enabled at IRQ 20
[ 0.684009] pci 0000:00:04.1: PCI INT B -> Link[UB12] -> GSI 20 (level, low) -> IRQ 20
[ 0.684249] pci 0000:00:04.1: PCI INT B disabled
[ 0.684480] pci 0000:00:08.0: Enabling HT MSI Mapping
[ 0.684710] pci 0000:00:09.0: Enabling HT MSI Mapping
[ 0.684946] pci 0000:00:0a.0: Enabling HT MSI Mapping
[ 0.685278] pci 0000:04:00.0: Boot video device
[ 0.685297] PCI: CLS 64 bytes, default 64
[ 0.686714] IBS: LVT offset 1 assigned
[ 0.686864] perf: AMD IBS detected (0x0000001f)
[ 0.687581] microcode: CPU0: patch_level=0x01000086
[ 0.687722] microcode: CPU1: patch_level=0x01000086
[ 0.687871] microcode: CPU2: patch_level=0x01000086
[ 0.688021] microcode: CPU3: patch_level=0x01000086
[ 0.688241] microcode: Microcode Update Driver: v2.00 <tigran@aivazian.fsnet.co.uk>, Peter Oruba
[ 0.688718] audit: initializing netlink socket (disabled)
[ 0.688864] type=2000 audit(1344547905.686:1): initialized
[ 0.708327] VFS: Disk quotas dquot_6.5.2
[ 0.710127] Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
[ 0.710807] Registering the id_resolver key type
[ 0.711360] fuse init (API version 7.17)
[ 0.711648] SGI XFS with ACLs, security attributes, realtime, large block/inode numbers, no debug enabled
[ 0.712415] SGI XFS Quota Management subsystem
[ 0.712554] msgmni has been set to 4003
[ 0.712783] SELinux: Registering netfilter hooks
[ 0.713434] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 253)
[ 0.713664] io scheduler noop registered
[ 0.713796] io scheduler deadline registered
[ 0.714019] io scheduler cfq registered (default)
[ 0.714932] input: Power Button as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input0
[ 0.715166] ACPI: Power Button [PWRB]
[ 0.715394] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input1
[ 0.715624] ACPI: Power Button [PWRF]
[ 0.715888] ACPI: processor limited to max C-state 1
[ 0.718806] Serial: 8250/16550 driver, 4 ports, IRQ sharing enabled
[ 0.907581] ahci 0000:00:09.0: version 3.0
[ 0.907683] ACPI: PCI Interrupt Link [LSA0] enabled at IRQ 23
[ 0.907827] ahci 0000:00:09.0: PCI INT A -> Link[LSA0] -> GSI 23 (level, low) -> IRQ 23
[ 0.908082] ahci 0000:00:09.0: irq 40 for MSI/MSI-X
[ 0.908086] ahci 0000:00:09.0: controller can't do PMP, turning off CAP_PMP
[ 0.908272] ahci 0000:00:09.0: AHCI 0001.0200 32 slots 6 ports 3 Gbps 0x3f impl SATA mode
[ 0.908506] ahci 0000:00:09.0: flags: 64bit ncq sntf led clo pio boh
[ 0.908651] ahci 0000:00:09.0: setting latency timer to 64
[ 0.909781] scsi0 : ahci
[ 0.910059] scsi1 : ahci
[ 0.910313] scsi2 : ahci
[ 0.910566] scsi3 : ahci
[ 0.910819] scsi4 : ahci
[ 0.911074] scsi5 : ahci
[ 0.911349] ata1: SATA max UDMA/133 abar m8192@0xdff76000 port 0xdff76100 irq 40
[ 0.911578] ata2: SATA max UDMA/133 abar m8192@0xdff76000 port 0xdff76180 irq 40
[ 0.911807] ata3: SATA max UDMA/133 abar m8192@0xdff76000 port 0xdff76200 irq 40
[ 0.912037] ata4: SATA max UDMA/133 abar m8192@0xdff76000 port 0xdff76280 irq 40
[ 0.912266] ata5: SATA max UDMA/133 abar m8192@0xdff76000 port 0xdff76300 irq 40
[ 0.912496] ata6: SATA max UDMA/133 abar m8192@0xdff76000 port 0xdff76380 irq 40
[ 0.913152] pata_amd 0000:00:06.0: version 0.4.1
[ 0.913174] pata_amd 0000:00:06.0: setting latency timer to 64
[ 0.913646] scsi6 : pata_amd
[ 0.913892] scsi7 : pata_amd
[ 0.914654] ata7: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 0.914801] ata8: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 0.915402] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.915547] ehci_hcd: block sizes: qh 112 qtd 96 itd 192 sitd 96
[ 0.915557] ehci_hcd 0000:00:02.1: PCI INT B -> Link[LUB2] -> GSI 22 (level, low) -> IRQ 22
[ 0.915799] ehci_hcd 0000:00:02.1: setting latency timer to 64
[ 0.915801] ehci_hcd 0000:00:02.1: EHCI Host Controller
[ 0.916045] ehci_hcd 0000:00:02.1: new USB bus registered, assigned bus number 1
[ 0.916278] ehci_hcd 0000:00:02.1: reset hcs_params 0x101f86 dbg=1 cc=1 pcc=15 !ppc ports=6
[ 0.916284] ehci_hcd 0000:00:02.1: reset portroute 0 0 0 0 0 0
[ 0.916286] ehci_hcd 0000:00:02.1: reset hcc_params a086 caching frame 256/512/1024 park
[ 0.916295] ehci_hcd 0000:00:02.1: park 0
[ 0.916299] ehci_hcd 0000:00:02.1: debug port 1
[ 0.916436] ehci_hcd 0000:00:02.1: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 0.916442] ehci_hcd 0000:00:02.1: cache line size of 64 is not supported
[ 0.916444] ehci_hcd 0000:00:02.1: supports USB remote wakeup
[ 0.916458] ehci_hcd 0000:00:02.1: irq 22, io mem 0xdff7fc00
[ 0.916600] ehci_hcd 0000:00:02.1: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 0.916605] ehci_hcd 0000:00:02.1: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[ 0.923607] ehci_hcd 0000:00:02.1: USB 2.0 started, EHCI 1.00
[ 0.923767] usb usb1: default language 0x0409
[ 0.923771] usb usb1: udev 1, busnum 1, minor = 0
[ 0.923773] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.923918] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.924147] usb usb1: Product: EHCI Host Controller
[ 0.924284] usb usb1: Manufacturer: Linux 3.2.23 ehci_hcd
[ 0.924423] usb usb1: SerialNumber: 0000:00:02.1
[ 0.924679] usb usb1: usb_probe_device
[ 0.924681] usb usb1: configuration #1 chosen from 1 choice
[ 0.924686] usb usb1: adding 1-0:1.0 (config #1, interface 0)
[ 0.924733] hub 1-0:1.0: usb_probe_interface
[ 0.924734] hub 1-0:1.0: usb_probe_interface - got id
[ 0.924736] hub 1-0:1.0: USB hub found
[ 0.924870] hub 1-0:1.0: 6 ports detected
[ 0.925003] hub 1-0:1.0: standalone hub
[ 0.925004] hub 1-0:1.0: no power switching (usb 1.0)
[ 0.925005] hub 1-0:1.0: individual port over-current protection
[ 0.925006] hub 1-0:1.0: power on to power good time: 20ms
[ 0.925009] hub 1-0:1.0: local power source is good
[ 0.925010] hub 1-0:1.0: trying to enable port power on non-switchable hub
[ 0.925048] ehci_hcd 0000:00:04.1: PCI INT B -> Link[UB12] -> GSI 20 (level, low) -> IRQ 20
[ 0.925287] ehci_hcd 0000:00:04.1: setting latency timer to 64
[ 0.925288] ehci_hcd 0000:00:04.1: EHCI Host Controller
[ 0.925521] ehci_hcd 0000:00:04.1: new USB bus registered, assigned bus number 2
[ 0.925753] ehci_hcd 0000:00:04.1: reset hcs_params 0x101f86 dbg=1 cc=1 pcc=15 !ppc ports=6
[ 0.925759] ehci_hcd 0000:00:04.1: reset portroute 0 0 0 0 0 0
[ 0.925761] ehci_hcd 0000:00:04.1: reset hcc_params a086 caching frame 256/512/1024 park
[ 0.925769] ehci_hcd 0000:00:04.1: park 0
[ 0.925773] ehci_hcd 0000:00:04.1: debug port 1
[ 0.925909] ehci_hcd 0000:00:04.1: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 0.925915] ehci_hcd 0000:00:04.1: cache line size of 64 is not supported
[ 0.925916] ehci_hcd 0000:00:04.1: supports USB remote wakeup
[ 0.925929] ehci_hcd 0000:00:04.1: irq 20, io mem 0xdff7f800
[ 0.926071] ehci_hcd 0000:00:04.1: reset command 0080b02 park=3 ithresh=8 period=1024 Reset HALT
[ 0.926076] ehci_hcd 0000:00:04.1: init command 0010005 (park)=0 ithresh=1 period=512 RUN
[ 0.933623] ehci_hcd 0000:00:04.1: USB 2.0 started, EHCI 1.00
[ 0.933784] usb usb2: default language 0x0409
[ 0.933787] usb usb2: udev 1, busnum 2, minor = 128
[ 0.933789] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.933934] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.934162] usb usb2: Product: EHCI Host Controller
[ 0.934299] usb usb2: Manufacturer: Linux 3.2.23 ehci_hcd
[ 0.934438] usb usb2: SerialNumber: 0000:00:04.1
[ 0.934686] usb usb2: usb_probe_device
[ 0.934687] usb usb2: configuration #1 chosen from 1 choice
[ 0.934690] usb usb2: adding 2-0:1.0 (config #1, interface 0)
[ 0.934736] hub 2-0:1.0: usb_probe_interface
[ 0.934737] hub 2-0:1.0: usb_probe_interface - got id
[ 0.934738] hub 2-0:1.0: USB hub found
[ 0.934872] hub 2-0:1.0: 6 ports detected
[ 0.935005] hub 2-0:1.0: standalone hub
[ 0.935006] hub 2-0:1.0: no power switching (usb 1.0)
[ 0.935007] hub 2-0:1.0: individual port over-current protection
[ 0.935008] hub 2-0:1.0: power on to power good time: 20ms
[ 0.935010] hub 2-0:1.0: local power source is good
[ 0.935011] hub 2-0:1.0: trying to enable port power on non-switchable hub
[ 0.935082] ohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driver
[ 0.935226] ohci_hcd: block sizes: ed 80 td 96
[ 0.935235] ohci_hcd 0000:00:02.0: PCI INT A -> Link[LUB0] -> GSI 23 (level, low) -> IRQ 23
[ 0.935475] ohci_hcd 0000:00:02.0: setting latency timer to 64
[ 0.935477] ohci_hcd 0000:00:02.0: OHCI Host Controller
[ 0.935709] ohci_hcd 0000:00:02.0: new USB bus registered, assigned bus number 3
[ 0.935951] ohci_hcd 0000:00:02.0: created debug files
[ 0.935952] ohci_hcd 0000:00:02.0: supports USB remote wakeup
[ 0.935966] ohci_hcd 0000:00:02.0: irq 23, io mem 0xdff7e000
[ 0.988962] ohci_hcd 0000:00:02.0: OHCI controller state
[ 0.988964] ohci_hcd 0000:00:02.0: OHCI 1.0, NO legacy support registers
[ 0.988966] ohci_hcd 0000:00:02.0: control 0x683 RWE RWC HCFS=operational CBSR=3
[ 0.988968] ohci_hcd 0000:00:02.0: cmdstatus 0x00000 SOC=0
[ 0.988971] ohci_hcd 0000:00:02.0: intrstatus 0x00000004 SF
[ 0.988973] ohci_hcd 0000:00:02.0: intrenable 0x8000005a MIE RHSC UE RD WDH
[ 0.988977] ohci_hcd 0000:00:02.0: hcca frame #0003
[ 0.988979] ohci_hcd 0000:00:02.0: roothub.a 01001206 POTPGT=1 NOCP NPS NDP=6(6)
[ 0.988982] ohci_hcd 0000:00:02.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 0.988984] ohci_hcd 0000:00:02.0: roothub.status 00008000 DRWE
[ 0.988987] ohci_hcd 0000:00:02.0: roothub.portstatus [0] 0x00000100 PPS
[ 0.988989] ohci_hcd 0000:00:02.0: roothub.portstatus [1] 0x00000100 PPS
[ 0.988992] ohci_hcd 0000:00:02.0: roothub.portstatus [2] 0x00000100 PPS
[ 0.988994] ohci_hcd 0000:00:02.0: roothub.portstatus [3] 0x00000100 PPS
[ 0.988996] ohci_hcd 0000:00:02.0: roothub.portstatus [4] 0x00000100 PPS
[ 0.988999] ohci_hcd 0000:00:02.0: roothub.portstatus [5] 0x00000100 PPS
[ 0.989003] usb usb3: default language 0x0409
[ 0.989007] usb usb3: udev 1, busnum 3, minor = 256
[ 0.989008] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 0.989153] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.989381] usb usb3: Product: OHCI Host Controller
[ 0.989518] usb usb3: Manufacturer: Linux 3.2.23 ohci_hcd
[ 0.989658] usb usb3: SerialNumber: 0000:00:02.0
[ 0.989909] usb usb3: usb_probe_device
[ 0.989910] usb usb3: configuration #1 chosen from 1 choice
[ 0.989913] usb usb3: adding 3-0:1.0 (config #1, interface 0)
[ 0.989959] hub 3-0:1.0: usb_probe_interface
[ 0.989960] hub 3-0:1.0: usb_probe_interface - got id
[ 0.989962] hub 3-0:1.0: USB hub found
[ 0.990125] hub 3-0:1.0: 6 ports detected
[ 0.990259] hub 3-0:1.0: standalone hub
[ 0.990260] hub 3-0:1.0: no power switching (usb 1.0)
[ 0.990261] hub 3-0:1.0: no over-current protection
[ 0.990262] hub 3-0:1.0: power on to power good time: 2ms
[ 0.990264] hub 3-0:1.0: local power source is good
[ 0.990266] hub 3-0:1.0: trying to enable port power on non-switchable hub
[ 0.990290] ehci_hcd 0000:00:02.1: HS companion for 0000:00:02.0
[ 0.990302] ohci_hcd 0000:00:04.0: PCI INT A -> Link[UB11] -> GSI 21 (level, low) -> IRQ 21
[ 0.990540] ohci_hcd 0000:00:04.0: setting latency timer to 64
[ 0.990542] ohci_hcd 0000:00:04.0: OHCI Host Controller
[ 0.990773] ohci_hcd 0000:00:04.0: new USB bus registered, assigned bus number 4
[ 0.991009] ohci_hcd 0000:00:04.0: created debug files
[ 0.991010] ohci_hcd 0000:00:04.0: supports USB remote wakeup
[ 0.991023] ohci_hcd 0000:00:04.0: irq 21, io mem 0xdff7d000
[ 1.023608] ehci_hcd 0000:00:02.1: GetStatus port:1 status 001803 0 ACK POWER sig=j CSC CONNECT
[ 1.023611] hub 1-0:1.0: port 1: status 0501 change 0001
[ 1.033605] ehci_hcd 0000:00:04.1: GetStatus port:2 status 001403 0 ACK POWER sig=k CSC CONNECT
[ 1.033607] hub 2-0:1.0: port 2: status 0501 change 0001
[ 1.045610] ohci_hcd 0000:00:04.0: OHCI controller state
[ 1.045612] ohci_hcd 0000:00:04.0: OHCI 1.0, NO legacy support registers
[ 1.045614] ohci_hcd 0000:00:04.0: control 0x683 RWE RWC HCFS=operational CBSR=3
[ 1.045616] ohci_hcd 0000:00:04.0: cmdstatus 0x00000 SOC=0
[ 1.045618] ohci_hcd 0000:00:04.0: intrstatus 0x00000004 SF
[ 1.045620] ohci_hcd 0000:00:04.0: intrenable 0x8000005a MIE RHSC UE RD WDH
[ 1.045624] ohci_hcd 0000:00:04.0: hcca frame #0003
[ 1.045626] ohci_hcd 0000:00:04.0: roothub.a 01001206 POTPGT=1 NOCP NPS NDP=6(6)
[ 1.045629] ohci_hcd 0000:00:04.0: roothub.b 00000000 PPCM=0000 DR=0000
[ 1.045631] ohci_hcd 0000:00:04.0: roothub.status 00008000 DRWE
[ 1.045633] ohci_hcd 0000:00:04.0: roothub.portstatus [0] 0x00000100 PPS
[ 1.045636] ohci_hcd 0000:00:04.0: roothub.portstatus [1] 0x00000100 PPS
[ 1.045638] ohci_hcd 0000:00:04.0: roothub.portstatus [2] 0x00000100 PPS
[ 1.045641] ohci_hcd 0000:00:04.0: roothub.portstatus [3] 0x00000100 PPS
[ 1.045643] ohci_hcd 0000:00:04.0: roothub.portstatus [4] 0x00000100 PPS
[ 1.045646] ohci_hcd 0000:00:04.0: roothub.portstatus [5] 0x00000100 PPS
[ 1.045650] usb usb4: default language 0x0409
[ 1.045653] usb usb4: udev 1, busnum 4, minor = 384
[ 1.045654] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 1.045800] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 1.046028] usb usb4: Product: OHCI Host Controller
[ 1.046165] usb usb4: Manufacturer: Linux 3.2.23 ohci_hcd
[ 1.046304] usb usb4: SerialNumber: 0000:00:04.0
[ 1.046556] usb usb4: usb_probe_device
[ 1.046558] usb usb4: configuration #1 chosen from 1 choice
[ 1.046561] usb usb4: adding 4-0:1.0 (config #1, interface 0)
[ 1.046607] hub 4-0:1.0: usb_probe_interface
[ 1.046608] hub 4-0:1.0: usb_probe_interface - got id
[ 1.046609] hub 4-0:1.0: USB hub found
[ 1.046775] hub 4-0:1.0: 6 ports detected
[ 1.046908] hub 4-0:1.0: standalone hub
[ 1.046909] hub 4-0:1.0: no power switching (usb 1.0)
[ 1.046910] hub 4-0:1.0: no over-current protection
[ 1.046912] hub 4-0:1.0: power on to power good time: 2ms
[ 1.046914] hub 4-0:1.0: local power source is good
[ 1.046915] hub 4-0:1.0: trying to enable port power on non-switchable hub
[ 1.046940] ehci_hcd 0000:00:04.1: HS companion for 0000:00:04.0
[ 1.047038] usbcore: registered new interface driver libusual
[ 1.047266] i8042: PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
[ 1.047412] i8042: PNP: PS/2 appears to have AUX port disabled, if this is incorrect please boot with i8042.nopnp
[ 1.047895] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 1.048165] mousedev: PS/2 mouse device common for all mice
[ 1.048570] rtc_cmos 00:06: RTC can wake from S4
[ 1.048916] rtc_cmos 00:06: rtc core: registered rtc_cmos as rtc0
[ 1.049107] rtc0: alarms up to one year, y3k, 114 bytes nvram, hpet irqs
[ 1.049304] cpuidle: using governor ladder
[ 1.049438] cpuidle: using governor menu
[ 1.049571] EFI Variables Facility v0.08 2004-May-17
[ 1.049892] usbcore: registered new interface driver usbhid
[ 1.050063] usbhid: USB HID core driver
[ 1.050574] snd_hda_intel 0000:00:07.0: power state changed by ACPI to D0
[ 1.050723] snd_hda_intel 0000:00:07.0: power state changed by ACPI to D0
[ 1.050966] ACPI: PCI Interrupt Link [LAZA] enabled at IRQ 22
[ 1.051109] snd_hda_intel 0000:00:07.0: PCI INT A -> Link[LAZA] -> GSI 22 (level, low) -> IRQ 22
[ 1.051344] hda_intel: Disabling MSI
[ 1.051484] snd_hda_intel 0000:00:07.0: setting latency timer to 64
[ 1.069309] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input2
[ 1.090284] hub 3-0:1.0: state 7 ports 6 chg 0000 evt 0000
[ 1.123602] hub 1-0:1.0: state 7 ports 6 chg 0002 evt 0000
[ 1.123607] hub 1-0:1.0: port 1, status 0501, change 0000, 480 Mb/s
[ 1.129968] ata7.00: ATA-7: ST3500630A, 3.AAE, max UDMA/100
[ 1.130155] ata7.00: 976773168 sectors, multi 16: LBA48
[ 1.130299] ata7.01: ATAPI: \bL-D\x14-\x13T\x04V\x04-\x12O\r \aD\x128162B, 0015, max UDMA/33
[ 1.130446] ata7: nv_mode_filter: 0x3f39f&0x3f39f->0x3f39f, BIOS=0x3f000 (0xc6c00000) ACPI=0x3f01f (20:60:0x15)
[ 1.130449] ata7: nv_mode_filter: 0x739f&0x739f->0x739f, BIOS=0x7000 (0xc6c00000) ACPI=0x701f (20:60:0x15)
[ 1.177130] ehci_hcd 0000:00:02.1: port 1 high speed
[ 1.177133] ehci_hcd 0000:00:02.1: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 1.196513] ata7.00: configured for UDMA/100
[ 1.210507] ata7.01: configured for UDMA/33
[ 1.230271] ata3: SATA link down (SStatus 0 SControl 300)
[ 1.230421] ata1: SATA link down (SStatus 0 SControl 300)
[ 1.230572] ata5: SATA link down (SStatus 0 SControl 300)
[ 1.230722] ata6: SATA link down (SStatus 0 SControl 300)
[ 1.230731] usb 1-1: new high-speed USB device number 2 using ehci_hcd
[ 1.283830] ehci_hcd 0000:00:02.1: port 1 high speed
[ 1.283833] ehci_hcd 0000:00:02.1: GetStatus port:1 status 001005 0 ACK POWER sig=se0 PE CONNECT
[ 1.354627] usb 1-1: udev 2, busnum 1, minor = 1
[ 1.354629] usb 1-1: New USB device found, idVendor=0409, idProduct=005a
[ 1.354774] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.355034] usb 1-1: usb_probe_device
[ 1.355036] usb 1-1: configuration #1 chosen from 1 choice
[ 1.355379] usb 1-1: adding 1-1:1.0 (config #1, interface 0)
[ 1.355432] hub 1-1:1.0: usb_probe_interface
[ 1.355433] hub 1-1:1.0: usb_probe_interface - got id
[ 1.355435] hub 1-1:1.0: USB hub found
[ 1.355903] hub 1-1:1.0: 4 ports detected
[ 1.356036] hub 1-1:1.0: standalone hub
[ 1.356038] hub 1-1:1.0: individual port power switching
[ 1.356039] hub 1-1:1.0: individual port over-current protection
[ 1.356040] hub 1-1:1.0: Single TT
[ 1.356041] hub 1-1:1.0: TT requires at most 16 FS bit times (1332 ns)
[ 1.356042] hub 1-1:1.0: Port indicators are supported
[ 1.356043] hub 1-1:1.0: power on to power good time: 0ms
[ 1.356739] hub 1-1:1.0: local power source is good
[ 1.356740] hub 1-1:1.0: enabling power on all ports
[ 1.358243] hub 2-0:1.0: state 7 ports 6 chg 0004 evt 0000
[ 1.358246] hub 2-0:1.0: port 2, status 0501, change 0000, 480 Mb/s
[ 1.358251] ehci_hcd 0000:00:04.1: port 2 low speed --> companion
[ 1.410259] ehci_hcd 0000:00:04.1: GetStatus port:2 status 003402 0 ACK POWER OWNER sig=k CSC
[ 1.410269] hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0004
[ 1.410273] ohci_hcd 0000:00:04.0: GetStatus roothub.portstatus [1] = 0x00010301 CSC LSDA PPS CCS
[ 1.410275] hub 4-0:1.0: port 2, status 0301, change 0001, 1.5 Mb/s
[ 1.458356] hub 1-1:1.0: port 4: status 0101 change 0001
[ 1.530251] hub 4-0:1.0: debounce: port 2: total 100ms stable 100ms status 0x301
[ 1.556917] usb 1-1: link qh256-0001/ffff88007c9c9380 start 1 [1/0 us]
[ 1.580251] hda_codec: ALC1200: BIOS auto-probing.
[ 1.636930] ohci_hcd 0000:00:04.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
[ 1.686945] Refined TSC clocksource calibration: 3173.333 MHz.
[ 1.687091] Switching to clocksource tsc
[ 1.690568] usb 4-2: new low-speed USB device number 2 using ohci_hcd
[ 1.796904] ohci_hcd 0000:00:04.0: GetStatus roothub.portstatus [1] = 0x00100303 PRSC LSDA PPS PES CCS
[ 1.875851] usb 4-2: skipped 1 descriptor after interface
[ 1.878843] usb 4-2: default language 0x0409
[ 1.886853] usb 4-2: udev 2, busnum 4, minor = 385
[ 1.886854] usb 4-2: New USB device found, idVendor=045e, idProduct=00cb
[ 1.887002] usb 4-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.887149] usb 4-2: Product: Microsoft Basic Optical Mouse v2.0
[ 1.887291] usb 4-2: Manufacturer: Microsoft
[ 1.887513] usb 4-2: usb_probe_device
[ 1.887515] usb 4-2: configuration #1 chosen from 1 choice
[ 1.889852] usb 4-2: adding 4-2:1.0 (config #1, interface 0)
[ 1.889892] usbhid 4-2:1.0: usb_probe_interface
[ 1.889893] usbhid 4-2:1.0: usb_probe_interface - got id
[ 1.896989] input: Microsoft Microsoft Basic Optical Mouse v2.0 as /devices/pci0000:00/0000:00:04.0/usb4/4-2/4-2:1.0/input/input3
[ 1.897353] generic-usb 0003:045E:00CB.0001: input,hidraw0: USB HID v1.11 Mouse [Microsoft Microsoft Basic Optical Mouse v2.0 ] on usb-0000:00:04.0-2/input0
[ 1.897628] hub 2-0:1.0: state 7 ports 6 chg 0000 evt 0004
[ 1.897633] hub 1-1:1.0: state 7 ports 4 chg 0010 evt 0000
[ 1.898010] hub 1-1:1.0: port 4, status 0101, change 0000, 12 Mb/s
[ 1.910977] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 1.923571] ata2: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.923723] ata4: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.924740] ata2.00: ATA-7: Maxtor 6Y160M0, YAR51EW0, max UDMA/133
[ 1.924884] ata2.00: 320173056 sectors, multi 0: LBA48
[ 1.925027] ata4.00: ATA-7: Maxtor 6Y160M0, YAR51EW0, max UDMA/133
[ 1.925171] ata4.00: 320173056 sectors, multi 0: LBA48
[ 1.926317] ata2.00: configured for UDMA/133
[ 1.926555] scsi 1:0:0:0: Direct-Access ATA Maxtor 6Y160M0 YAR5 PQ: 0 ANSI: 5
[ 1.926802] ata4.00: configured for UDMA/133
[ 1.926939] sd 1:0:0:0: [sda] 320173056 512-byte logical blocks: (163 GB/152 GiB)
[ 1.926997] sd 1:0:0:0: [sda] Write Protect is off
[ 1.926999] sd 1:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 1.927019] sd 1:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.927646] sd 1:0:0:0: Attached scsi generic sg0 type 0
[ 1.927901] scsi 3:0:0:0: Direct-Access ATA Maxtor 6Y160M0 YAR5 PQ: 0 ANSI: 5
[ 1.928280] sd 3:0:0:0: [sdb] 320173056 512-byte logical blocks: (163 GB/152 GiB)
[ 1.928565] sd 3:0:0:0: [sdb] Write Protect is off
[ 1.928608] sd 3:0:0:0: Attached scsi generic sg1 type 0
[ 1.928714] scsi 6:0:0:0: Direct-Access ATA ST3500630A 3.AA PQ: 0 ANSI: 5
[ 1.928839] sd 6:0:0:0: [sdc] 976773168 512-byte logical blocks: (500 GB/465 GiB)
[ 1.928880] sd 6:0:0:0: [sdc] Write Protect is off
[ 1.928882] sd 6:0:0:0: [sdc] Mode Sense: 00 3a 00 00
[ 1.928902] sd 6:0:0:0: [sdc] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.928909] sd 6:0:0:0: Attached scsi generic sg2 type 0
[ 1.931376] sd 3:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 1.931387] sd 3:0:0:0: [sdb] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 1.943599] scsi scan: 96 byte inquiry failed. Consider BLIST_INQUIRY_36 for this device
[ 1.948560] sda: sda1 sda2 sda3 sda4
[ 1.948994] sd 1:0:0:0: [sda] Attached SCSI disk
[ 1.951260] sdb: sdb1 sdb2
[ 1.951562] sd 3:0:0:0: [sdb] Attached SCSI disk
[ 1.963192] scsi 6:0:1:0: CD-ROM H - T-S D D-R M G R8162 0015 PQ: 0 ANSI: 5
[ 1.977916] usb 1-1.4: new full-speed USB device number 3 using ehci_hcd
[ 1.990599] hub 1-1:1.0: port 4 not reset yet, waiting 10ms
[ 1.991904] sr0: scsi-1 drive
[ 1.992046] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.992282] sr 6:0:1:0: Attached scsi CD-ROM sr0
[ 1.992354] sr 6:0:1:0: Attached scsi generic sg3 type 5
[ 1.992550] ata8: port disabled--ignoring
[ 2.034390] sdc: sdc1 sdc2 < sdc5 sdc6 sdc7 sdc8 >
[ 2.034929] sd 6:0:0:0: [sdc] Attached SCSI disk
[ 2.078726] usb 1-1.4: udev 3, busnum 1, minor = 2
[ 2.078728] usb 1-1.4: New USB device found, idVendor=0a21, idProduct=8001
[ 2.078875] usb 1-1.4: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 2.079190] usb 1-1.4: usb_probe_device
[ 2.079191] usb 1-1.4: configuration #1 chosen from 1 choice
[ 2.079728] usb 1-1.4: adding 1-1.4:1.0 (config #1, interface 0)
[ 2.079781] hub 4-0:1.0: state 7 ports 6 chg 0000 evt 0004
[ 2.079785] hub 1-1:1.0: state 7 ports 4 chg 0000 evt 0010
[ 2.433914] input: HDA NVidia Headphone as /devices/pci0000:00/0000:00:07.0/sound/card0/input4
[ 2.467011] ALSA device list:
[ 2.467139] #0: HDA NVidia at 0xdff78000 irq 22
[ 2.467332] Netfilter messages via NETLINK v0.30.
[ 2.467480] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 2.467919] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 2.468081] TCP cubic registered
[ 2.468210] Initializing XFRM netlink socket
[ 2.468518] NET: Registered protocol family 10
[ 2.468923] ip6_tables: (C) 2000-2006 Netfilter Core Team
[ 2.469091] IPv6 over IPv4 tunneling driver
[ 2.469552] NET: Registered protocol family 17
[ 2.469693] Registering the dns_resolver key type
[ 2.469991] registered taskstats version 1
[ 2.470475] Magic number: 8:394:550
[ 2.470644] pci_link PNP0C0F:01: hash matches
[ 2.470812] powernow-k8: Found 1 AMD Phenom(tm) II X4 920 Processor (4 cpu cores) (version 2.20.00)
[ 2.471069] powernow-k8: 0 : pstate 0 (2800 MHz)
[ 2.471206] powernow-k8: 1 : pstate 1 (2100 MHz)
[ 2.471343] powernow-k8: 2 : pstate 2 (1600 MHz)
[ 2.471480] powernow-k8: 3 : pstate 3 (800 MHz)
[ 2.636549] XFS (sdc6): Mounting Filesystem
[ 2.802132] XFS (sdc6): Starting recovery (logdev: internal)
[ 3.340348] hub 3-0:1.0: hub_suspend
[ 3.340360] usb usb3: bus auto-suspend, wakeup 1
[ 3.340366] ohci_hcd 0000:00:02.0: suspend root hub
[ 3.488158] XFS (sdc6): Ending recovery (logdev: internal)
[ 3.488329] VFS: Mounted root (xfs filesystem) readonly on device 8:38.
[ 3.523763] devtmpfs: mounted
[ 3.525622] Freeing unused kernel memory: 464k freed
[ 3.525959] Write protecting the kernel read-only data: 8192k
[ 3.528304] Freeing unused kernel memory: 252k freed
[ 3.529461] Freeing unused kernel memory: 108k freed
[ 4.320321] hub 2-0:1.0: hub_suspend
[ 4.320333] usb usb2: bus auto-suspend, wakeup 1
[ 4.320339] ehci_hcd 0000:00:04.1: suspend root hub
[ 4.410547] cat used greatest stack depth: 5096 bytes left
[ 4.520837] setfont used greatest stack depth: 4888 bytes left
[ 4.574209] init-early.sh used greatest stack depth: 4728 bytes left
[ 12.982749] systemd-udevd[1005]: starting version 186
[ 13.869278] i2c i2c-0: nForce2 SMBus adapter at 0x600
[ 13.869283] ACPI: resource nForce2_smbus [io 0x0700-0x073f] conflicts with ACPI region SM00 [io 0x700-0x73f]
[ 13.869284] ACPI: If an ACPI driver is available for this device, you should use it instead of the native driver
[ 14.016948] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 14.017351] ACPI: PCI Interrupt Link [LMAC] enabled at IRQ 21
[ 14.017363] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 14.017372] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 14.081979] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 14.081988] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 15.698337] nvidia: module license 'NVIDIA' taints kernel.
[ 15.698349] nvidia: module license 'NVIDIA' taints kernel.
[ 15.698361] nvidia: module license 'NVIDIA' taints kernel.
[ 15.698371] Disabling lock debugging due to kernel taint
[ 15.758893] nvidia 0000:04:00.0: PCI INT A -> Link[LN0A] -> GSI 19 (level, low) -> IRQ 19
[ 15.758901] nvidia 0000:04:00.0: setting latency timer to 64
[ 15.758905] vgaarb: device changed decodes: PCI:0000:04:00.0,olddecodes=io+mem,decodes=none:owns=io+mem
[ 15.758907] vgaarb: transferring owner from PCI:0000:04:00.0 to PCI:0000:06:00.0
[ 15.759017] nvidia 0000:05:00.0: enabling device (0000 -> 0003)
[ 15.759157] ACPI: PCI Interrupt Link [LN0C] enabled at IRQ 16
[ 15.759169] nvidia 0000:05:00.0: PCI INT A -> Link[LN0C] -> GSI 16 (level, low) -> IRQ 16
[ 15.759174] nvidia 0000:05:00.0: setting latency timer to 64
[ 15.759184] vgaarb: device changed decodes: PCI:0000:05:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 15.759285] nvidia 0000:06:00.0: enabling device (0000 -> 0003)
[ 15.759377] ACPI: PCI Interrupt Link [LN0D] enabled at IRQ 19
[ 15.759379] nvidia 0000:06:00.0: PCI INT A -> Link[LN0D] -> GSI 19 (level, low) -> IRQ 19
[ 15.759384] nvidia 0000:06:00.0: setting latency timer to 64
[ 15.759393] vgaarb: device changed decodes: PCI:0000:06:00.0,olddecodes=io+mem,decodes=none:owns=none
[ 15.759481] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 302.17 Tue Jun 12 16:03:22 PDT 2012
[ 43.423732] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 108.216066] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 108.216099] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 108.216109] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 108.275280] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 108.275289] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 565.745883] runscript.sh used greatest stack depth: 4600 bytes left
[ 566.286734] Adding 3204932k swap on /dev/sdc8. Priority:-1 extents:1 across:3204932k
[ 566.300503] Adding 2000056k swap on /dev/sda1. Priority:-2 extents:1 across:2000056k
[ 566.311912] Adding 2000056k swap on /dev/sdb1. Priority:-3 extents:1 across:2000056k
[ 566.864647] EXT4-fs (sdc7): mounting ext2 file system using the ext4 subsystem
[ 566.883104] EXT4-fs (sdc7): warning: mounting unchecked fs, running e2fsck is recommended
[ 566.886446] EXT4-fs (sdc7): mounted filesystem without journal. Opts: (null)
[ 566.924474] EXT4-fs (sda3): mounting ext2 file system using the ext4 subsystem
[ 566.933486] EXT4-fs (sda3): warning: mounting unchecked fs, running e2fsck is recommended
[ 566.935350] EXT4-fs (sda3): mounted filesystem without journal. Opts: (null)
[ 839.328806] tar used greatest stack depth: 4560 bytes left
[ 852.730225] CE: hpet increased min_delta_ns to 11520 nsec
[ 864.125742] collect2 used greatest stack depth: 4328 bytes left
[ 1005.876668] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 1043.115823] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 1043.115858] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 1043.115868] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 1043.178529] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 1043.178539] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 1470.133551] flush-8:32 used greatest stack depth: 3728 bytes left
[ 2247.149862] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 2250.284833] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 2250.284872] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 2250.284882] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 2250.345054] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 2250.345064] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 3565.993069] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 3569.296204] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 3569.296244] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 3569.296254] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 3569.358267] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 3569.358276] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 4520.699646] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 4929.427672] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 4929.427706] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 4929.427716] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 4929.488136] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 4929.488145] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 5020.399580] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 5042.561695] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 5042.561729] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 5042.561739] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 5042.621450] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 5042.621459] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim msi desc-v3
[ 5071.049589] forcedeth 0000:00:0a.0: PCI INT A disabled
[ 5077.585933] forcedeth: Reverse Engineered nForce ethernet driver. Version 0.64.
[ 5077.585966] forcedeth 0000:00:0a.0: PCI INT A -> Link[LMAC] -> GSI 21 (level, low) -> IRQ 21
[ 5077.585976] forcedeth 0000:00:0a.0: setting latency timer to 64
[ 5077.648100] forcedeth 0000:00:0a.0: ifname eth0, PHY OUI 0x732 @ 3, addr 00:24:8c:6b:67:2a
[ 5077.648109] forcedeth 0000:00:0a.0: highdma csum pwrctl mgmt gbit lnktim desc-v3
[ 5397.079798] flush-8:32 used greatest stack depth: 3616 bytes left
[-- Attachment #3: iomem --]
[-- Type: text/plain, Size: 2710 bytes --]
00000000-0000ffff : reserved
00010000-0009fbff : System RAM
0009fc00-0009ffff : reserved
000a0000-000bffff : PCI Bus 0000:00
000c0000-000cc3ff : Video ROM
000cc800-000cdfff : Adapter ROM
000d0000-000dffff : PCI Bus 0000:00
000d0000-000d3fff : pnp 00:04
000d4000-000d7fff : pnp 00:04
000de000-000dffff : pnp 00:04
000e3000-000fffff : reserved
000f0000-000fffff : System ROM
00100000-7ff8ffff : System RAM
01000000-015bbe52 : Kernel code
015bbe53-0188cfbf : Kernel data
01907000-019b8fff : Kernel bss
7ff90000-7ffa7fff : ACPI Tables
7ffa8000-7ffdffff : ACPI Non-volatile Storage
7ffe0000-7fffffff : reserved
80000000-dfffffff : PCI Bus 0000:00
90000000-cfffffff : PCI Bus 0000:02
90000000-cfffffff : PCI Bus 0000:03
90000000-9fffffff : PCI Bus 0000:04
90000000-9fffffff : 0000:04:00.0
a0000000-bfffffff : PCI Bus 0000:05
a0000000-bfffffff : 0000:05:00.0
c0000000-cfffffff : PCI Bus 0000:06
c0000000-cfffffff : 0000:06:00.0
dff76000-dff77fff : 0000:00:09.0
dff76000-dff77fff : ahci
dff78000-dff7bfff : 0000:00:07.0
dff78000-dff7bfff : ICH HD audio
dff7c000-dff7cfff : 0000:00:0a.0
dff7c000-dff7cfff : forcedeth
dff7d000-dff7dfff : 0000:00:04.0
dff7d000-dff7dfff : ohci_hcd
dff7e000-dff7efff : 0000:00:02.0
dff7e000-dff7efff : ohci_hcd
dff7f000-dff7f00f : 0000:00:0a.0
dff7f000-dff7f00f : forcedeth
dff7f400-dff7f4ff : 0000:00:0a.0
dff7f400-dff7f4ff : forcedeth
dff7f800-dff7f8ff : 0000:00:04.1
dff7f800-dff7f8ff : ehci_hcd
dff7fc00-dff7fcff : 0000:00:02.1
dff7fc00-dff7fcff : ehci_hcd
dff80000-dfffffff : 0000:00:01.3
e0000000-efffffff : PCI MMCONFIG 0000 [bus 00-ff]
e0000000-efffffff : pnp 00:0a
f0000000-febfffff : PCI Bus 0000:00
f0000000-fbffffff : PCI Bus 0000:02
f0000000-fbffffff : PCI Bus 0000:03
f0000000-f3ffffff : PCI Bus 0000:04
f0000000-f1ffffff : 0000:04:00.0
f2fe0000-f2ffffff : 0000:04:00.0
f3000000-f3ffffff : 0000:04:00.0
f3000000-f3ffffff : nvidia
f4000000-f7ffffff : PCI Bus 0000:05
f4000000-f5ffffff : 0000:05:00.0
f6f80000-f6ffffff : 0000:05:00.0
f7000000-f7ffffff : 0000:05:00.0
f7000000-f7ffffff : nvidia
f8000000-fbffffff : PCI Bus 0000:06
f8000000-f9ffffff : 0000:06:00.0
fafe0000-faffffff : 0000:06:00.0
fb000000-fbffffff : 0000:06:00.0
fb000000-fbffffff : nvidia
fec00000-fec00fff : reserved
fec00000-fec003ff : IOAPIC 0
fed00000-fed003ff : HPET 0
fed04000-fed04fff : pnp 00:04
fee00000-feefffff : reserved
fee00000-fee00fff : Local APIC
fee00000-fee00fff : pnp 00:07
fee01000-feefffff : pnp 00:04
fff00000-ffffffff : reserved
[-- Attachment #4: ioports --]
[-- Type: text/plain, Size: 1734 bytes --]
0000-0cf7 : PCI Bus 0000:00
0000-001f : dma1
0020-0021 : pic1
0040-0043 : timer0
0050-0053 : timer1
0060-0060 : keyboard
0064-0064 : keyboard
0070-0071 : rtc0
0080-008f : dma page reg
00a0-00a1 : pic2
00c0-00df : dma2
00f0-00ff : fpu
0170-0177 : 0000:00:06.0
0170-0177 : pata_amd
01f0-01f7 : 0000:00:06.0
01f0-01f7 : pata_amd
0230-023f : pnp 00:09
0290-029f : pnp 00:09
0376-0376 : 0000:00:06.0
0376-0376 : pata_amd
03c0-03df : vga+
03f6-03f6 : 0000:00:06.0
03f6-03f6 : pata_amd
04d0-04d1 : pnp 00:04
0500-057f : pnp 00:04
0500-0503 : ACPI PM1a_EVT_BLK
0504-0505 : ACPI PM1a_CNT_BLK
0508-050b : ACPI PM_TMR
0510-0515 : ACPI CPU throttle
0520-0527 : ACPI GPE0_BLK
0580-05ff : pnp 00:04
0600-063f : 0000:00:01.1
0600-063f : nForce2_smbus
0700-073f : 0000:00:01.1
0800-080f : pnp 00:04
0880-08ff : pnp 00:04
08a0-08af : ACPI GPE1_BLK
0900-09ff : 0000:00:01.0
0a00-0a0f : pnp 00:09
0a10-0a1f : pnp 00:09
0cf8-0cff : PCI conf1
0d00-ffff : PCI Bus 0000:00
0d00-0d7f : pnp 00:04
0d80-0dff : pnp 00:04
0e00-0e3f : 0000:00:01.1
a480-a487 : 0000:00:0a.0
a480-a487 : forcedeth
a800-a80f : 0000:00:09.0
a800-a80f : ahci
a880-a883 : 0000:00:09.0
a880-a883 : ahci
ac00-ac07 : 0000:00:09.0
ac00-ac07 : ahci
b000-b003 : 0000:00:09.0
b000-b003 : ahci
b080-b087 : 0000:00:09.0
b080-b087 : ahci
c000-efff : PCI Bus 0000:02
c000-efff : PCI Bus 0000:03
c000-cfff : PCI Bus 0000:04
cc00-cc7f : 0000:04:00.0
d000-dfff : PCI Bus 0000:05
dc00-dc7f : 0000:05:00.0
e000-efff : PCI Bus 0000:06
ec00-ec7f : 0000:06:00.0
ffa0-ffaf : 0000:00:06.0
ffa0-ffaf : pata_amd
[-- Attachment #5: lspci --]
[-- Type: text/plain, Size: 39004 bytes --]
00:00.0 RAM memory: NVIDIA Corporation MCP78S [GeForce 8200] Memory Controller (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Capabilities: [94] HyperTransport: #1a
Capabilities: [60] HyperTransport: Retry Mode
Capabilities: [44] HyperTransport: Slave or Primary Interface
Command: BaseUnitID=0 UnitCnt=0 MastHost- DefDir- DUL-
Link Control 0: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 0: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Link Control 1: CFlE- CST- CFE- <LkFail+ Init- EOC+ TXO+ <CRCErr=0 IsocEn- LSEn- ExtCTL- 64b-
Link Config 1: MLWI=8bit DwFcIn- MLWO=8bit DwFcOut- LWI=8bit DwFcInEn- LWO=8bit DwFcOutEn-
Revision ID: 3.00
Link Frequency 0: [a]
Link Error 0: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 0: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA- UIDRD+
Link Frequency 1: 200MHz
Link Error 1: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability 1: 200MHz- 300MHz- 400MHz- 500MHz- 600MHz- 800MHz- 1.0GHz- 1.2GHz- 1.4GHz- 1.6GHz- Vend-
Error Handling: PFlE- OFlE- PFE- OFE- EOCFE- RFE- CRCFE- SERRFE- CF- RE- PNFE- ONFE- EOCNFE- RNFE- CRCNFE- SERRNFE-
Prefetchable memory behind bridge Upper: 00-00
Bus Number: 00
Capabilities: [d0] HyperTransport: #1c
00:01.0 ISA bridge: NVIDIA Corporation MCP78S [GeForce 8200] LPC Bridge (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Region 0: I/O ports at 0900 [size=256]
00:01.1 SMBus: NVIDIA Corporation MCP78S [GeForce 8200] SMBus (rev a1)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Interrupt: pin A routed to IRQ 10
Region 0: I/O ports at 0e00 [size=64]
Region 4: I/O ports at 0600 [size=64]
Region 5: I/O ports at 0700 [size=64]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: nForce2_smbus
00:01.2 RAM memory: NVIDIA Corporation MCP78S [GeForce 8200] Memory Controller (rev a1)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:01.3 Co-processor: NVIDIA Corporation MCP78S [GeForce 8200] Co-Processor (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 7
Region 0: Memory at dff80000 (32-bit, non-prefetchable) [size=512K]
00:01.4 RAM memory: NVIDIA Corporation MCP78S [GeForce 8200] Memory Controller (rev a1)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap- 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:02.0 USB controller: NVIDIA Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 23
Region 0: Memory at dff7e000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:02.1 USB controller: NVIDIA Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller (rev a1) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 22
Region 0: Memory at dff7fc00 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=00a0
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:04.0 USB controller: NVIDIA Corporation MCP78S [GeForce 8200] OHCI USB 1.1 Controller (rev a1) (prog-if 10 [OHCI])
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at dff7d000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ohci_hcd
00:04.1 USB controller: NVIDIA Corporation MCP78S [GeForce 8200] EHCI USB 2.0 Controller (rev a1) (prog-if 20 [EHCI])
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin B routed to IRQ 20
Region 0: Memory at dff7f800 (32-bit, non-prefetchable) [size=256]
Capabilities: [44] Debug port: BAR=1 offset=00a0
Capabilities: [80] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: ehci_hcd
00:06.0 IDE interface: NVIDIA Corporation MCP78S [GeForce 8200] IDE (rev a1) (prog-if 8a [Master SecP PriP])
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Region 0: [virtual] Memory at 000001f0 (32-bit, non-prefetchable) [size=8]
Region 1: [virtual] Memory at 000003f0 (type 3, non-prefetchable)
Region 2: [virtual] Memory at 00000170 (32-bit, non-prefetchable) [size=8]
Region 3: [virtual] Memory at 00000370 (type 3, non-prefetchable)
Region 4: I/O ports at ffa0 [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: pata_amd
00:07.0 Audio device: NVIDIA Corporation MCP72XE/MCP72P/MCP78U/MCP78S High Definition Audio (rev a1)
Subsystem: ASUSTeK Computer Inc. Device 8357
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (500ns min, 1250ns max)
Interrupt: pin A routed to IRQ 22
Region 0: Memory at dff78000 (32-bit, non-prefetchable) [size=16K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Kernel driver in use: snd_hda_intel
00:08.0 PCI bridge: NVIDIA Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1) (prog-if 01 [Subtractive decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: fff00000-000fffff
Secondary status: 66MHz- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort+ <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr+ DiscTmrStat- DiscTmrSERREn-
Capabilities: [b8] Subsystem: ASUSTeK Computer Inc. Device 82e7
Capabilities: [8c] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
00:09.0 SATA controller: NVIDIA Corporation MCP78S [GeForce 8200] AHCI Controller (rev a2) (prog-if 01 [AHCI 1.0])
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- DisINTx+
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (750ns min, 250ns max)
Interrupt: pin A routed to IRQ 40
Region 0: I/O ports at b080 [size=8]
Region 1: I/O ports at b000 [size=4]
Region 2: I/O ports at ac00 [size=8]
Region 3: I/O ports at a880 [size=4]
Region 4: I/O ports at a800 [size=16]
Region 5: Memory at dff76000 (32-bit, non-prefetchable) [size=8K]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [8c] SATA HBA v1.0 InCfgSpace
Capabilities: [b0] MSI: Enable+ Count=1/8 Maskable- 64bit+
Address: 00000000fee0f00c Data: 4171
Capabilities: [ec] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: ahci
00:0a.0 Ethernet controller: NVIDIA Corporation MCP77 Ethernet (rev a2)
Subsystem: ASUSTeK Computer Inc. Device 82e7
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0 (250ns min, 5000ns max)
Interrupt: pin A routed to IRQ 21
Region 0: Memory at dff7c000 (32-bit, non-prefetchable) [size=4K]
Region 1: I/O ports at a480 [size=8]
Region 2: Memory at dff7f400 (32-bit, non-prefetchable) [size=256]
Region 3: Memory at dff7f000 (32-bit, non-prefetchable) [size=16]
Capabilities: [44] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable+ DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/16 Maskable+ 64bit+
Address: 0000000000000000 Data: 0000
Masking: 00000000 Pending: 00000000
Capabilities: [6c] HyperTransport: MSI Mapping Enable+ Fixed+
Kernel driver in use: forcedeth
00:10.0 PCI bridge: NVIDIA Corporation MCP78S [GeForce 8200] PCI Express Bridge (rev a1) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=02, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000efff
Memory behind bridge: f0000000-fbffffff
Prefetchable memory behind bridge: 0000000090000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ASUSTeK Computer Inc. Device 82e7
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v2) Root Port (Slot-), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
DevCap2: Completion Timeout: Range AB, TimeoutDis+, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 65ms to 210ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Kernel driver in use: pcieport
00:13.0 PCI bridge: NVIDIA Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=07, subordinate=07, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ASUSTeK Computer Inc. Device 82e7
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet- Interlock-
Changed: MRL- PresDet+ LinkState-
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport
00:14.0 PCI bridge: NVIDIA Corporation MCP78S [GeForce 8200] PCI Bridge (rev a1) (prog-if 00 [Normal decode])
Control: I/O- Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=00, secondary=08, subordinate=08, sec-latency=0
I/O behind bridge: 0000f000-00000fff
Memory behind bridge: fff00000-000fffff
Prefetchable memory behind bridge: 00000000fff00000-00000000000fffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Subsystem: ASUSTeK Computer Inc. Device 82e7
Capabilities: [48] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [50] MSI: Enable- Count=1/2 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [60] HyperTransport: MSI Mapping Enable+ Fixed-
Mapping Address Base: 00000000fee00000
Capabilities: [80] Express (v1) Root Port (Slot+), MSI 00
DevCap: MaxPayload 256 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #4, Speed 2.5GT/s, Width x1, ASPM L0s L1, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot-
LnkCtl: ASPM Disabled; RCB 64 bytes Disabled+ Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x1, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #5, PowerLimit 10.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Off, PwrInd On, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet+ LinkState+
RootCtl: ErrCorrectable- ErrNon-Fatal- ErrFatal- PMEIntEna- CRSVisible-
RootCap: CRSVisible-
RootSta: PME ReqID 0000, PMEStatus- PMEPending-
Kernel driver in use: pcieport
00:18.0 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor HyperTransport Configuration
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [80] HyperTransport: Host or Secondary Interface
Command: WarmRst+ DblEnd- DevNum=0 ChainSide- HostHide+ Slave- <EOCErr- DUL-
Link Control: CFlE- CST- CFE- <LkFail- Init+ EOC- TXO- <CRCErr=0 IsocEn- LSEn+ ExtCTL- 64b-
Link Config: MLWI=16bit DwFcIn- MLWO=16bit DwFcOut- LWI=16bit DwFcInEn- LWO=16bit DwFcOutEn-
Revision ID: 3.00
Link Frequency: [a]
Link Error: <Prot- <Ovfl- <EOC- CTLTm-
Link Frequency Capability: 200MHz+ 300MHz- 400MHz+ 500MHz- 600MHz+ 800MHz+ 1.0GHz+ 1.2GHz+ 1.4GHz- 1.6GHz- Vend-
Feature Capability: IsocFC+ LDTSTOP+ CRCTM- ECTLT- 64bA+ UIDRD- ExtRS- UCnfE-
00:18.1 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Address Map
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.2 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor DRAM Controller
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
00:18.3 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Miscellaneous Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Capabilities: [f0] Secure device <?>
00:18.4 Host bridge: Advanced Micro Devices [AMD] Family 10h Processor Link Control
Control: I/O- Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap- 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
02:00.0 PCI bridge: NVIDIA Corporation NF200 PCIe 2.0 switch (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=02, secondary=03, subordinate=06, sec-latency=0
I/O behind bridge: 0000c000-0000efff
Memory behind bridge: f0000000-fbffffff
Prefetchable memory behind bridge: 0000000090000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Express (v2) Upstream Port, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-SlotPowerLimit 0.000W
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [a0] Subsystem: NVIDIA Corporation Device c55e
Kernel driver in use: pcieport
03:00.0 PCI bridge: NVIDIA Corporation NF200 PCIe 2.0 switch (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=03, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: 0000c000-0000cfff
Memory behind bridge: f0000000-f3ffffff
Prefetchable memory behind bridge: 0000000090000000-000000009fffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA+ MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 5GT/s, Width x16, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive+ BWMgmt- ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #1, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Kernel driver in use: pcieport
03:02.0 PCI bridge: NVIDIA Corporation NF200 PCIe 2.0 switch (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=03, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000d000-0000dfff
Memory behind bridge: f4000000-f7ffffff
Prefetchable memory behind bridge: 00000000a0000000-00000000bfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x8, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #3, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Kernel driver in use: pcieport
03:03.0 PCI bridge: NVIDIA Corporation NF200 PCIe 2.0 switch (rev a2) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx+
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0, Cache Line Size: 64 bytes
Bus: primary=03, secondary=06, subordinate=06, sec-latency=0
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: f8000000-fbffffff
Prefetchable memory behind bridge: 00000000c0000000-00000000cfffffff
Secondary status: 66MHz- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- <SERR- <PERR-
BridgeCtl: Parity- SERR+ NoISA- VGA- MAbort- >Reset- FastB2B-
PriDiscTmr- SecDiscTmr- DiscTmrStat- DiscTmrSERREn-
Capabilities: [40] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0+,D1-,D2-,D3hot+,D3cold+)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [60] Express (v2) Downstream Port (Slot+), MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <64ns, L1 <1us
ExtTag+ RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd- ExtTag- PhantFunc- AuxPwr- NoSnoop-
MaxPayload 128 bytes, MaxReadReq 128 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x8, ASPM L0s, Latency L0 <512ns, L1 <4us
ClockPM- Surprise- LLActRep+ BwNot+
LnkCtl: ASPM Disabled; Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive+ BWMgmt+ ABWMgmt-
SltCap: AttnBtn- PwrCtrl- MRL- AttnInd- PwrInd- HotPlug- Surprise-
Slot #4, PowerLimit 0.000W; Interlock- NoCompl-
SltCtl: Enable: AttnBtn- PwrFlt- MRL- PresDet- CmdCplt- HPIrq- LinkChg-
Control: AttnInd Unknown, PwrInd Unknown, Power- Interlock-
SltSta: Status: AttnBtn- PowerFlt- MRL- CmdCplt- PresDet+ Interlock-
Changed: MRL- PresDet- LinkState-
DevCap2: Completion Timeout: Not Supported, TimeoutDis-, LTR-, OBFF Not Supported ARIFwd-
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled ARIFwd-
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-, Selectable De-emphasis: -3.5dB
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -3.5dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Kernel driver in use: pcieport
04:00.0 VGA compatible controller: NVIDIA Corporation G80 [GeForce 8800 GTS] (rev a2) (prog-if 00 [VGA controller])
Subsystem: NVIDIA Corporation Device 0421
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at f3000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at 90000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f0000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at cc00 [size=128]
[virtual] Expansion ROM at f2fe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 2
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v1) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <1us, L1 <4us
ExtTag- AttnBtn- AttnInd- PwrInd- RBE- FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag- PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #0, Speed 2.5GT/s, Width x16, ASPM L0s L1, Latency L0 <1us, L1 <4us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk-
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 2.5GT/s, Width x16, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [128 v1] Power Budgeting <?>
Kernel driver in use: nvidia
05:00.0 VGA compatible controller: NVIDIA Corporation G96 [GeForce 9500 GT] (rev a1) (prog-if 00 [VGA controller])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 16
Region 0: Memory at f7000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at a0000000 (64-bit, prefetchable) [size=512M]
Region 3: Memory at f4000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at dc00 [size=128]
[virtual] Expansion ROM at f6f80000 [disabled] [size=512K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst- PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #2, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 2.5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [b4] Vendor Specific Information: Len=14 <?>
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nvidia
06:00.0 VGA compatible controller: NVIDIA Corporation G92 [GeForce 8800 GT] (rev a2) (prog-if 00 [VGA controller])
Subsystem: eVga.com. Corp. Device c802
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- DisINTx-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR- INTx-
Latency: 0
Interrupt: pin A routed to IRQ 19
Region 0: Memory at fb000000 (32-bit, non-prefetchable) [size=16M]
Region 1: Memory at c0000000 (64-bit, prefetchable) [size=256M]
Region 3: Memory at f8000000 (64-bit, non-prefetchable) [size=32M]
Region 5: I/O ports at ec00 [size=128]
[virtual] Expansion ROM at fafe0000 [disabled] [size=128K]
Capabilities: [60] Power Management version 3
Flags: PMEClk- DSI- D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 NoSoftRst+ PME-Enable- DSel=0 DScale=0 PME-
Capabilities: [68] MSI: Enable- Count=1/1 Maskable- 64bit+
Address: 0000000000000000 Data: 0000
Capabilities: [78] Express (v2) Endpoint, MSI 00
DevCap: MaxPayload 128 bytes, PhantFunc 0, Latency L0s <512ns, L1 <4us
ExtTag+ AttnBtn- AttnInd- PwrInd- RBE+ FLReset-
DevCtl: Report errors: Correctable- Non-Fatal- Fatal- Unsupported-
RlxdOrd+ ExtTag+ PhantFunc- AuxPwr- NoSnoop+
MaxPayload 128 bytes, MaxReadReq 512 bytes
DevSta: CorrErr- UncorrErr- FatalErr- UnsuppReq- AuxPwr- TransPend-
LnkCap: Port #3, Speed 5GT/s, Width x16, ASPM L0s L1, Latency L0 <256ns, L1 <1us
ClockPM- Surprise- LLActRep- BwNot-
LnkCtl: ASPM Disabled; RCB 128 bytes Disabled- Retrain- CommClk+
ExtSynch- ClockPM- AutWidDis- BWInt- AutBWInt-
LnkSta: Speed 5GT/s, Width x8, TrErr- Train- SlotClk+ DLActive- BWMgmt- ABWMgmt-
DevCap2: Completion Timeout: Not Supported, TimeoutDis+, LTR-, OBFF Not Supported
DevCtl2: Completion Timeout: 50us to 50ms, TimeoutDis-, LTR-, OBFF Disabled
LnkCtl2: Target Link Speed: 5GT/s, EnterCompliance- SpeedDis-
Transmit Margin: Normal Operating Range, EnterModifiedCompliance- ComplianceSOS-
Compliance De-emphasis: -6dB
LnkSta2: Current De-emphasis Level: -6dB, EqualizationComplete-, EqualizationPhase1-
EqualizationPhase2-, EqualizationPhase3-, LinkEqualizationRequest-
Capabilities: [100 v1] Virtual Channel
Caps: LPEVC=0 RefClk=100ns PATEntryBits=1
Arb: Fixed- WRR32- WRR64- WRR128-
Ctrl: ArbSelect=Fixed
Status: InProgress-
VC0: Caps: PATOffset=00 MaxTimeSlots=1 RejSnoopTrans-
Arb: Fixed- WRR32- WRR64- WRR128- TWRR128- WRR256-
Ctrl: Enable+ ID=0 ArbSelect=Fixed TC/VC=ff
Status: NegoPending- InProgress-
Capabilities: [128 v1] Power Budgeting <?>
Capabilities: [600 v1] Vendor Specific Information: ID=0001 Rev=1 Len=024 <?>
Kernel driver in use: nvidia
^ permalink raw reply [flat|nested] 2+ messages in thread