* Re: [PATCH] ARM: dts: omap4-panda-es: Do not reset gpio1
2013-10-10 16:44 ` [PATCH] ARM: dts: omap4-panda-es: Do not reset gpio1 Nishanth Menon
@ 2013-10-10 16:47 ` Tony Lindgren
2013-10-10 19:01 ` Nishanth Menon
2013-10-15 7:28 ` Benoit Cousson
1 sibling, 1 reply; 4+ messages in thread
From: Tony Lindgren @ 2013-10-10 16:47 UTC (permalink / raw)
To: Nishanth Menon
Cc: Benoît Cousson, Rajendra Nayak, linux-omap, devicetree,
linux-arm-kernel, linux-kernel
* Nishanth Menon <nm@ti.com> [131010 09:53]:
> Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
> OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
> supplies VDD_MPU.
>
> Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
> MPU voltage switches over to VSET0 voltage value (boot voltage) which
> is not sufficient to operate the device at OPP100.
Is this needs as a fix for the -rc series?
Tony
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
> As explained here: http://marc.info/?l=u-boot&m=133066647800872&w=2
>
> GPIO1 reset causes PandaBoard-ES to stop functioning.
> This depends on Patch series from Rajendra:
> http://marc.info/?l=linux-doc&m=138131355520116&w=2
> Applies on Benoit's for_13/dts branch:
> https://git.kernel.org/cgit/linux/kernel/git/bcousson/linux-omap-dt.git/log/?h=for_3.13/dts
>
> Tested on PandaBoard-ES without the u-boot uenv hack
>
> arch/arm/boot/dts/omap4-panda-es.dts | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
> index 56c4354..816d1c9 100644
> --- a/arch/arm/boot/dts/omap4-panda-es.dts
> +++ b/arch/arm/boot/dts/omap4-panda-es.dts
> @@ -62,3 +62,7 @@
> gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> };
> };
> +
> +&gpio1 {
> + ti,no-reset-on-init;
> +};
> --
> 1.7.9.5
>
> --
> To unsubscribe from this list: send the line "unsubscribe linux-kernel" in
> the body of a message to majordomo@vger.kernel.org
> More majordomo info at http://vger.kernel.org/majordomo-info.html
> Please read the FAQ at http://www.tux.org/lkml/
^ permalink raw reply [flat|nested] 4+ messages in thread* Re: [PATCH] ARM: dts: omap4-panda-es: Do not reset gpio1
2013-10-10 16:44 ` [PATCH] ARM: dts: omap4-panda-es: Do not reset gpio1 Nishanth Menon
2013-10-10 16:47 ` Tony Lindgren
@ 2013-10-15 7:28 ` Benoit Cousson
1 sibling, 0 replies; 4+ messages in thread
From: Benoit Cousson @ 2013-10-15 7:28 UTC (permalink / raw)
To: Nishanth Menon
Cc: Rajendra Nayak, linux-omap, devicetree, linux-arm-kernel, linux-kernel
Hi Nishanth,
On 10/10/2013 18:44, Nishanth Menon wrote:
> Do not reset GPIO1 at boot-up because GPIO 7 in GPIO1 block is used on
> OMAP4460 PandaBoard-ES to select voltage register in TPS62361 which
> supplies VDD_MPU.
>
> Without this, OMAP4460 PandaBoard-ES boards fail to boot-up because
> MPU voltage switches over to VSET0 voltage value (boot voltage) which
> is not sufficient to operate the device at OPP100.
>
> Signed-off-by: Nishanth Menon <nm@ti.com>
> ---
> As explained here: http://marc.info/?l=u-boot&m=133066647800872&w=2
>
> GPIO1 reset causes PandaBoard-ES to stop functioning.
> This depends on Patch series from Rajendra:
> http://marc.info/?l=linux-doc&m=138131355520116&w=2
> Applies on Benoit's for_13/dts branch:
> https://git.kernel.org/cgit/linux/kernel/git/bcousson/linux-omap-dt.git/log/?h=for_3.13/dts
I've just applied it after Rajendra's series.
Thanks,
Benoit
>
> Tested on PandaBoard-ES without the u-boot uenv hack
>
> arch/arm/boot/dts/omap4-panda-es.dts | 4 ++++
> 1 file changed, 4 insertions(+)
>
> diff --git a/arch/arm/boot/dts/omap4-panda-es.dts b/arch/arm/boot/dts/omap4-panda-es.dts
> index 56c4354..816d1c9 100644
> --- a/arch/arm/boot/dts/omap4-panda-es.dts
> +++ b/arch/arm/boot/dts/omap4-panda-es.dts
> @@ -62,3 +62,7 @@
> gpios = <&gpio1 8 GPIO_ACTIVE_HIGH>;
> };
> };
> +
> +&gpio1 {
> + ti,no-reset-on-init;
> +};
>
--
Benoît Cousson
BayLibre
Embedded Linux Technology Lab
www.baylibre.com
^ permalink raw reply [flat|nested] 4+ messages in thread