Re: Regression on next-20140116 [Was: [PATCH 3/3 v4] usb: chipidea: hw_phymode_configure moved before ci_usb_phy_init]

[Chris Ruehl <chris.ruehl@gtsys.com.hk>]

On Thursday, January 23, 2014 09:22 AM, Peter Chen wrote:
> On Wed, Jan 22, 2014 at 10:41:33PM +0100, Uwe Kleine-König wrote:
>> Hello,
>>
>> On Wed, Jan 22, 2014 at 10:49:51AM +0100, Uwe Kleine-König wrote:
>>> On Tue, Dec 03, 2013 at 04:01:50PM +0800, Chris Ruehl wrote:
>>>> usb: chipidea: hw_phymode_configure moved before ci_usb_phy_init
>>>> hw_phymode_configure configures the PORTSC registers and allow the
>>>> following phy_inits to operate on the right parameters. This fix a problem
>>>> where the UPLI (ISP1504) could not detected, because the Viewport was not
>>>> available and read the viewport return 0's only.
>>> This patch (or a later revision of it to be more exact) made it into
>>> mainline as cd0b42c2a6d2.
>>>
>>> On an i.MX27 based machine I'm hitting an oops (see below) on
>>> next-20140116 + a few patches. (I didn't switch to 3.13+ yet, as I think
>>> not everything I need has landed there.) The oops goes away (and still
>>> better, lsusb reports my connected devices instead of "unable to
>>> initialize libusb: -99") when I do at least one of the following:
>>>
>>>   - set CONFIG_USB_CHIPIDEA=y instead of =m
>>>   - revert commit
>>>        cd0b42c2a6d2 (usb: chipidea: put hw_phymode_configure before ci_usb_phy_init)
>> I debugged that a bit further and the problem is that
>> hw_phymode_configure depends on the phy's clk being enabled (i.e.
>> usb_ipg_gate) and this is only enforced in ci_usb_phy_init (via
>> usb_phy_init -> usb_gen_phy_init). When CONFIG_USB_CHIPIDEA=y the init
>> call to disable all unused clocks wasn't run yet and so the clock is
>> still on as this is the boot default.
> Hi Uwe,
> I am a little puzzled at your platform
>
> - Which phy you have used? ulpi phy ,internal phy or other external phy?
> - If you use ulpi phy, why you still need to use nop phy driver?
>   Besides, according to chris patch, the ulpi can only be visited after
> hw_phymode_configure?
> - Do you have some hardware related operation at phy's probe? If it exists,
> why not move it to phy->init?
>
> Peter
Peter,
I think thats my fault, I send Uwe my patches which call the phy-ulpi 
from the nop driver
in order to get the ISP1504 running with my board.

Its obversely wrong to call an other driver from the nop
see:  [PATCH 3/3] usb: phy-generic: Add ULPI VBUS support and the 
concerns from
Heikki (mail-list linux-usb)

Uwe we may work together on this.

Chris

>> Considering that it's already late today and that I don't know the
>> chipidea driver I'm sure there are people who can come up with a better
>> patch with less effort than me. Any volunteers?
>>
>> Best regards
>> Uwe
>>
>> -- 
>> Pengutronix e.K.                           | Uwe Kleine-König            |
>> Industrial Linux Solutions                 | http://www.pengutronix.de/  |
>>
>>