Re: [PATCH 1/6] dt-bindings: mdio-mux: Add documentation for mdio mux for NSP SoC

[Scott Branden <scott.branden@broadcom.com>]

One change

On 16-11-09 01:33 AM, Yendapally Reddy Dhananjaya Reddy wrote:
> Add documentation for mdio mux available in Broadcom NSP SoC
>
> Signed-off-by: Yendapally Reddy Dhananjaya Reddy <yendapally.reddy@broadcom.com>
> ---
>  .../devicetree/bindings/net/brcm,mdio-mux-nsp.txt  | 57 ++++++++++++++++++++++
>  1 file changed, 57 insertions(+)
>  create mode 100644 Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt
>
> diff --git a/Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt b/Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt
> new file mode 100644
> index 0000000..b749a2b
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/net/brcm,mdio-mux-nsp.txt
> @@ -0,0 +1,57 @@
> +Properties for an MDIO bus multiplexer available in Broadcom NSP SoC.
> +
> +This MDIO bus multiplexer defines buses that could access the internal
> +phys as well as external to SoCs. When child bus is selected, one needs
> +to select the below properties to generate desired MDIO transaction on
> +appropriate bus.
> +
> +Required properties in addition to the generic multiplexer properties:
> +
> +MDIO multiplexer node:
> +- compatible: brcm,mdio-mux-iproc.
This should be brcm,mdio-mux-nsp

> +- reg: Should contain registers location and length.
> +- reg-names: Should contain the resource reg names.
> +	- bus-ctrl: mdio bus control register address space required to
> +	  select the bus master. This property is not required for SoC's
> +	  that doesn't provide master selection.
> +	- mgmt-ctrl: mdio management control register address space
> +
> +Sub-nodes:
> +   Each bus master should be represented as a sub-node.
> +
> +Sub-nodes required properties:
> +- reg: Bus master number. Should be 0x10 to access the external mdio devices.
> +- address-cells: should be 1
> +- size-cells: should be 0
> +
> +Every non-ethernet PHY requires a compatible property so that it could be
> +probed based on this compatible string.
> +
> +Additional information regarding generic multiplexer properties can be found
> +at- Documentation/devicetree/bindings/net/mdio-mux.txt
> +
> +example:
> +
> +	mdio_mux: mdio-mux@3f190 {
> +		compatible = "brcm,mdio-mux-nsp";
> +		reg = <0x3f190 0x4>,
> +		      <0x32000 0x4>;
> +		reg-names = "bus-ctrl", "mgmt-ctrl";
> +		mdio-parent-bus = <&mdio>;
> +		#address-cells = <1>;
> +		#size-cells = <0>;
> +
> +		mdio@0 {
> +			reg = <0x0>;
> +			#address-cells = <1>;
> +			#size-cells = <0>;
> +
> +			usb3_phy: usb3-phy@10 {
> +				compatible = "brcm,nsp-usb3-phy";
> +				reg = <0x10>;
> +				usb3-ctrl-syscon = <&usb3_ctrl>;
> +				#phy-cells = <0>;
> +				status = "disabled";
> +			};
> +		};
> +	};
>