* Config Disk, RGL10364 device is on DMA blacklist
@ 2008-04-22 21:41 Bjoern Olausson
0 siblings, 0 replies; only message in thread
From: Bjoern Olausson @ 2008-04-22 21:41 UTC (permalink / raw)
To: linux-kernel, linux-ide, bugme-daemon
[-- Attachment #1: Type: text/plain, Size: 4034 bytes --]
Hi all,
I dont't know where this device is comming from and what it does or is
supposed to do.
Hardware: Asus P5W-DH Delux
Kernel: Stock 2.6.25
Distribution: Gentoo Linux
See attached files for more information.
Maybe related to:
http://bugzilla.kernel.org/show_bug.cgi?id=9010
http://bugzilla.kernel.org/show_bug.cgi?id=8923
can anybody comment on this:
[ 1.252722] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status
changed irq 1274
[ 4.783300] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.783408] ata2.00: ATA-6: Config Disk, RGL10364, max UDMA/133
[ 4.783459] ata2.00: 640 sectors, multi 1: LBA
[ 4.783500] ata2.00: device is on DMA blacklist, disabling DMA
[ 4.783628] ata2.00: configured for PIO4
[ 27.194668] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa
frozen
[ 27.194674] ata2.00: irq_stat 0x00400000, PHY RDY changed
[ 27.194677] ata2: SError: { PHYRdyChg }
[ 27.194684] ata2.00: cmd c4/00:08:80:01:00/00:00:00:00:00/e0 tag 0 pio 4096
in
[ 27.194689] ata2.00: status: { DRDY }
[ 27.194697] ata2: hard resetting link
[ 27.916803] ata2: SATA link down (SStatus 0 SControl 300)
[ 27.916813] ata2: failed to recover some devices, retrying in 5 secs
[ 32.917045] ata2: hard resetting link
[ 33.222000] ata2: SATA link down (SStatus 0 SControl 300)
[ 33.222007] ata2: failed to recover some devices, retrying in 5 secs
[ 38.222244] ata2: hard resetting link
[ 40.680697] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 40.680856] ata2.00: device is on DMA blacklist, disabling DMA
[ 40.680988] ata2.00: configured for PIO4
[ 40.680998] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 40.681000] ata2: irq_stat 0x00000040, connection status changed
[ 40.681173] ata2.00: device is on DMA blacklist, disabling DMA
[ 40.681301] ata2.00: configured for PIO4
[ 40.681307] ata2: EH complete
root@freax $ hdparm --verbose -I /dev/sdb
/dev/sdb:
outgoing cdb: 85 08 2e 00 00 00 00 00 00 00 00 00 00 40 ec 00
SG_IO: ATA_16 status=0x2, host_status=0x0, driver_status=0x8
SG_IO: sb[] = {72 00 00 00 00 00 00 0e}
SG_IO: desc[] = {09 0c .. }
ATA_16 tf->status=0x50 tf->error=0x00
ATA device, with non-removable media
Model Number: Config Disk
Serial Number: 0000000__________0_A
Firmware Revision: RGL10364
Standards:
Used: ATA/ATAPI-6 T13 1410D revision 2
Supported: 6 5 4
Configuration:
Logical max current
cylinders 16383 16383
heads 16 16
sectors/track 63 63
--
CHS current addressable sectors: 16514064
LBA user addressable sectors: 640
device size with M = 1024*1024: 8063 MBytes
device size with M = 1000*1000: 8455 MBytes (8 GB)
Capabilities:
LBA, IORDY(can be disabled)
Standby timer values: spec'd by Standard, no device specific minimum
R/W multiple sector transfer: Max = 1 Current = 1
Recommended acoustic management value: 192, current value: 254
DMA: mdma0 mdma1 *mdma2 udma0 udma1 udma2 udma3 udma4 udma5 *udma6 (?)
Cycle time: min=120ns recommended=120ns
PIO: pio0 pio1 pio2 pio3 pio4
Cycle time: no flow control=120ns IORDY flow control=120ns
Commands/features:
Enabled Supported:
Power Management feature set
Write cache
Look-ahead
Power-Up In Standby feature set
SET_FEATURES required to spinup after power up
* Mandatory FLUSH_CACHE
* unknown 76[0]
* Host-initiated interface power management
Security:
Master password revision code = 65534
supported
not enabled
not locked
not frozen
not expired: security count
not supported: enhanced erase
Checksum: correct
Thanks and kind regards
Bjoern
[-- Attachment #2: lshw.log --]
[-- Type: application/octet-stream, Size: 5464 bytes --]
H/W path Device Class Description
==============================================================
system P5W DH Deluxe
/0 bus P5W DH Deluxe
/0/0 memory 64KiB BIOS
/0/4 processor Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz
/0/4/5 memory 32KiB L1 cache
/0/4/6 memory 4MiB L2 cache
/0/4/7 memory L3 cache
/0/3c memory 2GiB System Memory
/0/3c/0 memory 1GiB DIMM SDRAM Synchronous
/0/3c/1 memory DIMM [empty]
/0/3c/2 memory 1GiB DIMM SDRAM Synchronous
/0/3c/3 memory DIMM [empty]
/0/100 bridge 82975X Memory Controller Hub
/0/100/1 bridge 82975X PCI Express Root Port
/0/100/1/0 display G70 [GeForce 7600 GT]
/0/100/1b multimedia 82801G (ICH7 Family) High Definition Audio Controller
/0/100/1c bridge 82801G (ICH7 Family) PCI Express Port 1
/0/100/1c.3 bridge 82801G (ICH7 Family) PCI Express Port 4
/0/100/1c.3/0 eth0 network 88E8053 PCI-E Gigabit Ethernet Controller
/0/100/1c.4 bridge 82801GR/GH/GHM (ICH7 Family) PCI Express Port 5
/0/100/1c.4/0 eth1 network 88E8053 PCI-E Gigabit Ethernet Controller
/0/100/1c.5 bridge 82801GR/GH/GHM (ICH7 Family) PCI Express Port 6
/0/100/1c.5/0 storage JMicron 20360/20363 AHCI Controller
/0/100/1c.5/0.1 storage JMicron 20360/20363 AHCI Controller
/0/100/1d bus 82801G (ICH7 Family) USB UHCI Controller #1
/0/100/1d/1 usb2 bus UHCI Host Controller
/0/100/1d/1/2 generic USB RECEIVER
/0/100/1d.1 bus 82801G (ICH7 Family) USB UHCI Controller #2
/0/100/1d.1/1 usb3 bus UHCI Host Controller
/0/100/1d.1/1/1 generic ASUS DH Remote
/0/100/1d.1/1/2 bus Logitech BT Mini-Receiver
/0/100/1d.1/1/2/2 generic Logitech BT Mini-Receiver
/0/100/1d.1/1/2/3 generic Logitech BT Mini-Receiver
/0/100/1d.2 bus 82801G (ICH7 Family) USB UHCI Controller #3
/0/100/1d.2/1 usb4 bus UHCI Host Controller
/0/100/1d.2/1/1 generic Bluetooth Device
/0/100/1d.3 bus 82801G (ICH7 Family) USB UHCI Controller #4
/0/100/1d.3/1 usb5 bus UHCI Host Controller
/0/100/1d.7 bus 82801G (ICH7 Family) USB2 EHCI Controller
/0/100/1d.7/1 usb1 bus EHCI Host Controller
/0/100/1d.7/1/1 bus USB2.0 Hub
/0/100/1d.7/1/1/2 generic iP5200
/0/100/1d.7/1/1/4 generic USB Receiver
/0/100/1d.7/1/7 bus USB2.0 Hub
/0/100/1d.7/1/7/1 bus USB2.0 Hub
/0/100/1d.7/1/7/2 scsi10 generic USB Storage
/0/100/1d.7/1/7/2/0.0.0 /dev/sdc disk STORAGE DEVICE
/0/100/1d.7/1/7/2/0.0.0/0 /dev/sdc disk
/0/100/1d.7/1/7/2/0.0.1 /dev/sdd disk STORAGE DEVICE
/0/100/1d.7/1/7/2/0.0.1/0 /dev/sdd disk
/0/100/1d.7/1/7/2/0.0.2 /dev/sde disk STORAGE DEVICE
/0/100/1d.7/1/7/2/0.0.2/0 /dev/sde disk
/0/100/1d.7/1/7/2/0.0.3 /dev/sdf disk STORAGE DEVICE
/0/100/1d.7/1/7/2/0.0.3/0 /dev/sdf disk
/0/100/1d.7/1/7/3 generic RTL8187_Wireless
/0/100/1e bridge 82801 PCI Bridge
/0/100/1e/0 multimedia SB X-Fi
/0/100/1e/1 wmaster0 network AR5212 802.11abg NIC
/0/100/1e/3 bus TSB43AB22/A IEEE-1394a-2000 Controller (PHY/Link)
/0/100/1f bridge 82801GB/GR (ICH7 Family) LPC Interface Bridge
/0/100/1f.1 scsi6 storage 82801G (ICH7 Family) IDE Controller
/0/100/1f.1/0.0.0 /dev/cdrom disk DVD-ROM PX-130A
/0/100/1f.2 scsi0 storage 82801GR/GH (ICH7 Family) SATA AHCI Controller
/0/100/1f.2/0 /dev/sda disk 74GB WDC WD740ADFD-00
/0/100/1f.2/0/1 /dev/sda1 volume 47MiB Linux filesystem partition
/0/100/1f.2/0/2 /dev/sda2 volume 956MiB Linux swap volume
/0/100/1f.2/0/3 /dev/sda3 volume 68GiB EXT3 volume
/0/100/1f.2/1 /dev/sdb disk 327KB Config Disk
/0/100/1f.3 bus 82801G (ICH7 Family) SMBus Controller
/1 wlan0 network Wireless interface
/2 irlan0 network Ethernet interface
[-- Attachment #3: p5w-DH-delux_dmesg.log --]
[-- Type: application/octet-stream, Size: 48567 bytes --]
[ 0.000000] Linux version 2.6.25-unpatched (root@freax) (gcc version 4.1.2 (Gentoo 4.1.2 p1.0.2)) #2 SMP PREEMPT Mon Apr 21 20:46:51 CEST 2008
[ 0.000000] Command line: root=/dev/sda3 video=nvidiafb:1280x1024-32@85,mtrr,ywrap
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000007ff80000 (usable)
[ 0.000000] BIOS-e820: 000000007ff80000 - 000000007ff8e000 (ACPI data)
[ 0.000000] BIOS-e820: 000000007ff8e000 - 000000007ffe0000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000007ffe0000 - 0000000080000000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffb00000 - 0000000100000000 (reserved)
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 524160) 1 entries of 3200 used
[ 0.000000] end_pfn_map = 1048576
[ 0.000000] DMI 2.4 present.
[ 0.000000] ACPI: RSDP 000FAF00, 0014 (r0 ACPIAM)
[ 0.000000] ACPI: RSDT 7FF80000, 0038 (r1 A_M_I_ OEMRSDT 1000817 MSFT 97)
[ 0.000000] ACPI: FACP 7FF80200, 0081 (r1 A_M_I_ OEMFACP 1000817 MSFT 97)
[ 0.000000] ACPI: DSDT 7FF80590, 9554 (r1 A0543 A0543000 0 INTL 20060113)
[ 0.000000] ACPI: FACS 7FF8E000, 0040
[ 0.000000] ACPI: APIC 7FF80390, 0080 (r1 A_M_I_ OEMAPIC 1000817 MSFT 97)
[ 0.000000] ACPI: OEMB 7FF8E040, 0066 (r1 A_M_I_ AMI_OEM 1000817 MSFT 97)
[ 0.000000] ACPI: HPET 7FF89AF0, 0038 (r1 A_M_I_ OEMHPET 1000817 MSFT 97)
[ 0.000000] ACPI: MCFG 7FF89B30, 003C (r1 A_M_I_ OEMMCFG 1000817 MSFT 97)
[ 0.000000] No NUMA configuration found
[ 0.000000] Faking a node at 0000000000000000-000000007ff80000
[ 0.000000] Entering add_active_range(0, 0, 159) 0 entries of 3200 used
[ 0.000000] Entering add_active_range(0, 256, 524160) 1 entries of 3200 used
[ 0.000000] Bootmem setup node 0 0000000000000000-000000007ff80000
[ 0.000000] NODE_DATA [000000000000c000 - 0000000000012fff]
[ 0.000000] bootmap [0000000000013000 - 0000000000022fef] pages 10
[ 0.000000] early res: 0 [0-fff] BIOS data page
[ 0.000000] early res: 1 [6000-7fff] SMP_TRAMPOLINE
[ 0.000000] early res: 2 [200000-db6387] TEXT DATA BSS
[ 0.000000] early res: 3 [9fc00-a0bff] EBDA
[ 0.000000] early res: 4 [8000-bfff] PGTABLE
[ 0.000000] [ffffe20000000000-ffffe200001fffff] PMD ->ffff810001200000 on node 0
[ 0.000000] [ffffe20000200000-ffffe200003fffff] PMD ->ffff810001400000 on node 0
[ 0.000000] [ffffe20000400000-ffffe200005fffff] PMD ->ffff810001800000 on node 0
[ 0.000000] [ffffe20000600000-ffffe200007fffff] PMD ->ffff810001c00000 on node 0
[ 0.000000] [ffffe20000800000-ffffe200009fffff] PMD ->ffff810001e00000 on node 0
[ 0.000000] [ffffe20000a00000-ffffe20000bfffff] PMD ->ffff810002200000 on node 0
[ 0.000000] [ffffe20000c00000-ffffe20000dfffff] PMD ->ffff810002600000 on node 0
[ 0.000000] [ffffe20000e00000-ffffe20000ffffff] PMD ->ffff810002a00000 on node 0
[ 0.000000] [ffffe20001000000-ffffe200011fffff] PMD ->ffff810002c00000 on node 0
[ 0.000000] [ffffe20001200000-ffffe200013fffff] PMD ->ffff810003000000 on node 0
[ 0.000000] [ffffe20001400000-ffffe200015fffff] PMD ->ffff810003400000 on node 0
[ 0.000000] [ffffe20001600000-ffffe200017fffff] PMD ->ffff810003800000 on node 0
[ 0.000000] [ffffe20001800000-ffffe200019fffff] PMD ->ffff810003a00000 on node 0
[ 0.000000] [ffffe20001a00000-ffffe20001bfffff] PMD ->ffff810003e00000 on node 0
[ 0.000000] [ffffe20001c00000-ffffe20001dfffff] PMD ->ffff810004200000 on node 0
[ 0.000000] [ffffe20001e00000-ffffe20001ffffff] PMD ->ffff810004400000 on node 0
[ 0.000000] [ffffe20002000000-ffffe200021fffff] PMD ->ffff810004800000 on node 0
[ 0.000000] [ffffe20002200000-ffffe200023fffff] PMD ->ffff810004c00000 on node 0
[ 0.000000] [ffffe20002400000-ffffe200025fffff] PMD ->ffff810005000000 on node 0
[ 0.000000] [ffffe20002600000-ffffe200027fffff] PMD ->ffff810005200000 on node 0
[ 0.000000] [ffffe20002800000-ffffe200029fffff] PMD ->ffff810005600000 on node 0
[ 0.000000] [ffffe20002a00000-ffffe20002bfffff] PMD ->ffff810005a00000 on node 0
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] DMA32 4096 -> 1048576
[ 0.000000] Normal 1048576 -> 1048576
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[2] active PFN ranges
[ 0.000000] 0: 0 -> 159
[ 0.000000] 0: 256 -> 524160
[ 0.000000] On node 0 totalpages: 524063
[ 0.000000] DMA zone: 88 pages used for memmap
[ 0.000000] DMA zone: 3008 pages reserved
[ 0.000000] DMA zone: 903 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 11173 pages used for memmap
[ 0.000000] DMA32 zone: 508891 pages, LIFO batch:31
[ 0.000000] Normal zone: 0 pages used for memmap
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] ACPI: PM-Timer IO Port: 0x808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
[ 0.000000] Processor #0 (Bootup-CPU)
[ 0.000000] ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
[ 0.000000] Processor #1
[ 0.000000] ACPI: LAPIC (acpi_id[0x03] lapic_id[0x82] disabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x04] lapic_id[0x83] disabled)
[ 0.000000] ACPI: IOAPIC (id[0x02] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 2, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Setting APIC routing to flat
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 88000000 (gap: 80000000:7fb00000)
[ 0.000000] SMP: Allowing 4 CPUs, 2 hotplug CPUs
[ 0.000000] PERCPU: Allocating 37832 bytes of per cpu data
[ 0.000000] Built 1 zonelists in Node order, mobility grouping on. Total pages: 509794
[ 0.000000] Policy zone: DMA32
[ 0.000000] Kernel command line: root=/dev/sda3 video=nvidiafb:1280x1024-32@85,mtrr,ywrap
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 32768 bytes)
[ 0.000000] TSC calibrated against PM_TIMER
[ 0.000002] time.c: Detected 2400.092 MHz processor.
[ 0.000999] Console: colour VGA+ 80x25
[ 0.000999] console [tty0] enabled
[ 0.000999] Lock dependency validator: Copyright (c) 2006 Red Hat, Inc., Ingo Molnar
[ 0.000999] ... MAX_LOCKDEP_SUBCLASSES: 8
[ 0.000999] ... MAX_LOCK_DEPTH: 48
[ 0.000999] ... MAX_LOCKDEP_KEYS: 2048
[ 0.000999] ... CLASSHASH_SIZE: 1024
[ 0.000999] ... MAX_LOCKDEP_ENTRIES: 8192
[ 0.000999] ... MAX_LOCKDEP_CHAINS: 16384
[ 0.000999] ... CHAINHASH_SIZE: 8192
[ 0.000999] memory used by lock dependency info: 1648 kB
[ 0.000999] per task-struct memory footprint: 2688 bytes
[ 0.000999] Checking aperture...
[ 0.000999] Memory: 2038724k/2096640k available (4418k kernel code, 57528k reserved, 2444k data, 384k init)
[ 0.000999] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.000999] SLUB: Genslabs=13, HWalign=64, Order=0-1, MinObjects=4, CPUs=4, Nodes=1
[ 0.000999] hpet clockevent registered
[ 0.059993] Calibrating delay using timer specific routine.. 4803.76 BogoMIPS (lpj=2401881)
[ 0.060365] Dentry cache hash table entries: 262144 (order: 9, 2097152 bytes)
[ 0.061595] Inode-cache hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.062293] Mount-cache hash table entries: 256
[ 0.062769] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.062832] CPU: L2 cache: 4096K
[ 0.062868] CPU 0/0 -> Node 0
[ 0.062903] CPU: Physical Processor ID: 0
[ 0.062939] CPU: Processor Core ID: 0
[ 0.062980] CPU0: Thermal monitoring enabled (TM2)
[ 0.062994] using mwait in idle threads.
[ 0.063042] ACPI: Core revision 20070126
[ 0.084572] Using local APIC timer interrupts.
[ 0.084988] APIC timer calibration result 16667325
[ 0.084990] Detected 16.667 MHz APIC timer.
[ 0.085239] lockdep: fixing up alternatives.
[ 0.085330] Booting processor 1/2 APIC 0x1
[ 0.000999] Initializing CPU#1
[ 0.000999] Calibrating delay using timer specific routine.. 4800.16 BogoMIPS (lpj=2400082)
[ 0.000999] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.000999] CPU: L2 cache: 4096K
[ 0.000999] CPU 1/1 -> Node 0
[ 0.000999] CPU: Physical Processor ID: 0
[ 0.000999] CPU: Processor Core ID: 1
[ 0.000999] CPU1: Thermal monitoring enabled (TM2)
[ 0.000999] Intel(R) Core(TM)2 CPU 6600 @ 2.40GHz stepping 06
[ 0.156527] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.157021] Brought up 2 CPUs
[ 0.158063] CPU0 attaching sched-domain:
[ 0.158065] domain 0: span 00000003
[ 0.158067] groups: 00000001 00000002
[ 0.158070] domain 1: span 00000003
[ 0.158072] groups: 00000003
[ 0.158075] CPU1 attaching sched-domain:
[ 0.158076] domain 0: span 00000003
[ 0.158078] groups: 00000002 00000001
[ 0.158080] domain 1: span 00000003
[ 0.158082] groups: 00000003
[ 0.158610] net_namespace: 512 bytes
[ 0.158921] NET: Registered protocol family 16
[ 0.159201] No dock devices found.
[ 0.159426] ACPI: bus type pci registered
[ 0.159594] PCI: BIOS Bug: MCFG area at f0000000 is not E820-reserved
[ 0.159633] PCI: Not using MMCONFIG.
[ 0.159669] PCI: Using configuration type 1
[ 0.166286] ACPI: EC: Look up EC in DSDT
[ 0.179335] ACPI: Interpreter enabled
[ 0.179372] ACPI: (supports S0 S5)
[ 0.179463] ACPI: Using IOAPIC for interrupt routing
[ 0.189152] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.189935] pci 0000:00:1f.0: quirk: region 0800-087f claimed by ICH6 ACPI/GPIO/TCO
[ 0.189988] pci 0000:00:1f.0: quirk: region 0480-04bf claimed by ICH6 GPIO
[ 0.191138] PCI: Transparent bridge - 0000:00:1e.0
[ 0.191214] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.191442] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT]
[ 0.191542] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P3._PRT]
[ 0.191710] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P4._PRT]
[ 0.191811] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P7._PRT]
[ 0.191889] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P8._PRT]
[ 0.191967] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P9._PRT]
[ 0.196465] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.196924] ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.197386] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 6 *7 10 11 12 14 15)
[ 0.197841] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.198283] ACPI: PCI Interrupt Link [LNKE] (IRQs *3 4 5 6 7 10 11 12 14 15)
[ 0.198739] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 7 10 *11 12 14 15)
[ 0.199207] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 7 10 11 12 14 15)
[ 0.199676] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *10 11 12 14 15)
[ 0.200200] ACPI Warning (tbutils-0217): Incorrect checksum in table [OEMB] - D0, should be C7 [20070126]
[ 0.200313] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.200395] pnp: PnP ACPI init
[ 0.200446] ACPI: bus type pnp registered
[ 0.204259] pnp: PnP ACPI: found 14 devices
[ 0.204298] ACPI: ACPI bus type pnp unregistered
[ 0.204564] SCSI subsystem initialized
[ 0.204669] libata version 3.00 loaded.
[ 0.204824] usbcore: registered new interface driver usbfs
[ 0.204916] usbcore: registered new interface driver hub
[ 0.205023] usbcore: registered new device driver usb
[ 0.205478] PCI: Using ACPI for IRQ routing
[ 0.205515] PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
[ 0.210019] NET: Registered protocol family 23
[ 0.210126] Bluetooth: Core ver 2.11
[ 0.210338] NET: Registered protocol family 31
[ 0.210375] Bluetooth: HCI device and connection manager initialized
[ 0.210425] Bluetooth: HCI socket layer initialized
[ 0.215183] PCI-GART: No AMD northbridge found.
[ 0.215223] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.215361] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.220005] system 00:01: iomem range 0xfed13000-0xfed19fff has been reserved
[ 0.220061] system 00:07: ioport range 0x290-0x297 has been reserved
[ 0.220111] system 00:08: ioport range 0x4d0-0x4d1 has been reserved
[ 0.220161] system 00:08: ioport range 0x800-0x87f has been reserved
[ 0.220200] system 00:08: ioport range 0x400-0x41f has been reserved
[ 0.220239] system 00:08: ioport range 0x480-0x4bf has been reserved
[ 0.220279] system 00:08: iomem range 0xfed1c000-0xfed1ffff has been reserved
[ 0.220318] system 00:08: iomem range 0xfed20000-0xfed3ffff has been reserved
[ 0.220358] system 00:08: iomem range 0xfed50000-0xfed8ffff has been reserved
[ 0.220398] system 00:08: iomem range 0xffb00000-0xffbfffff could not be reserved
[ 0.220446] system 00:08: iomem range 0xfff00000-0xffffffff could not be reserved
[ 0.220498] system 00:0a: iomem range 0xfec00000-0xfec00fff has been reserved
[ 0.220538] system 00:0a: iomem range 0xfee00000-0xfee00fff could not be reserved
[ 0.220590] system 00:0c: iomem range 0xf0000000-0xf3ffffff has been reserved
[ 0.220635] system 00:0d: iomem range 0x0-0x9ffff could not be reserved
[ 0.220675] system 00:0d: iomem range 0xc0000-0xdffff has been reserved
[ 0.220714] system 00:0d: iomem range 0xe0000-0xfffff could not be reserved
[ 0.220754] system 00:0d: iomem range 0x100000-0x7fffffff could not be reserved
[ 0.220801] system 00:0d: iomem range 0x0-0x0 could not be reserved
[ 0.221613] PCI: Bridge: 0000:00:01.0
[ 0.221981] IO window: c000-cfff
[ 0.222019] MEM window: 0xebe00000-0xefefffff
[ 0.222058] PREFETCH window: 0x00000000c3500000-0x00000000e34fffff
[ 0.222099] PCI: Bridge: 0000:00:1c.0
[ 0.222135] IO window: disabled.
[ 0.222173] MEM window: disabled.
[ 0.222211] PREFETCH window: 0x00000000c3400000-0x00000000c34fffff
[ 0.222254] PCI: Bridge: 0000:00:1c.3
[ 0.222291] IO window: b000-bfff
[ 0.222330] MEM window: 0xebd00000-0xebdfffff
[ 0.222368] PREFETCH window: disabled.
[ 0.222409] PCI: Bridge: 0000:00:1c.4
[ 0.222446] IO window: a000-afff
[ 0.222485] MEM window: 0xebc00000-0xebcfffff
[ 0.222523] PREFETCH window: disabled.
[ 0.222563] PCI: Bridge: 0000:00:1c.5
[ 0.222600] IO window: 9000-9fff
[ 0.222639] MEM window: 0xebb00000-0xebbfffff
[ 0.222987] PREFETCH window: disabled.
[ 0.223027] PCI: Bridge: 0000:00:1e.0
[ 0.223064] IO window: 8000-8fff
[ 0.223103] MEM window: 0xe3600000-0xebafffff
[ 0.223142] PREFETCH window: disabled.
[ 0.223195] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.223269] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.223287] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.223361] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.223380] ACPI: PCI Interrupt 0000:00:1c.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 0.223454] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.223471] ACPI: PCI Interrupt 0000:00:1c.4[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.223545] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.223564] ACPI: PCI Interrupt 0000:00:1c.5[B] -> GSI 17 (level, low) -> IRQ 17
[ 0.223637] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.223648] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.223659] NET: Registered protocol family 2
[ 0.233165] IP route cache hash table entries: 65536 (order: 7, 524288 bytes)
[ 0.234009] TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
[ 0.235979] TCP bind hash table entries: 65536 (order: 9, 3670016 bytes)
[ 0.240260] TCP: Hash tables configured (established 262144 bind 65536)
[ 0.240333] TCP reno registered
[ 0.088714] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[ 0.089480] Total HugeTLB memory allocated, 0
[ 0.094970] Installing knfsd (copyright (C) 1996 okir@monad.swb.de).
[ 0.095768] NTFS driver 2.1.29 [Flags: R/W].
[ 0.095974] fuse init (API version 7.9)
[ 0.096524] io scheduler noop registered
[ 0.096561] io scheduler deadline registered
[ 0.096750] io scheduler cfq registered (default)
[ 0.096905] pci 0000:06:00.0: Boot video device
[ 0.097085] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.097122] assign_interrupt_mode Found MSI capability
[ 0.097194] Allocate Port Service[0000:00:01.0:pcie00]
[ 0.097300] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.097335] assign_interrupt_mode Found MSI capability
[ 0.097406] Allocate Port Service[0000:00:1c.0:pcie00]
[ 0.097456] Allocate Port Service[0000:00:1c.0:pcie02]
[ 0.097564] PCI: Setting latency timer of device 0000:00:1c.3 to 64
[ 0.097597] assign_interrupt_mode Found MSI capability
[ 0.097668] Allocate Port Service[0000:00:1c.3:pcie00]
[ 0.097774] PCI: Setting latency timer of device 0000:00:1c.4 to 64
[ 0.097806] assign_interrupt_mode Found MSI capability
[ 0.097879] Allocate Port Service[0000:00:1c.4:pcie00]
[ 0.097980] PCI: Setting latency timer of device 0000:00:1c.5 to 64
[ 0.098018] assign_interrupt_mode Found MSI capability
[ 0.098090] Allocate Port Service[0000:00:1c.5:pcie00]
[ 0.098728] input: Power Button (FF) as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input0
[ 0.098797] ACPI: Power Button (FF) [PWRF]
[ 0.098943] input: Power Button (CM) as /devices/LNXSYSTM:00/device:00/PNP0C0C:00/input/input1
[ 0.098992] ACPI: Power Button (CM) [PWRB]
[ 0.255720] ACPI: ACPI0007:00 is registered as cooling_device0
[ 0.255763] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 0.100263] ACPI: ACPI0007:01 is registered as cooling_device1
[ 0.100305] ACPI: Processor [CPU2] (supports 8 throttling states)
[ 0.141570] Real Time Clock Driver v1.12ac
[ 0.141785] hpet_resources: 0xfed00000 is busy
[ 0.141989] intel_rng: FWH not detected
[ 0.142035] Linux agpgart interface v0.103
[ 0.142147] Floppy drive(s): fd0 is 1.44M
[ 0.157640] FDC 0 is a post-1991 82077
[ 0.159667] brd: module loaded
[ 0.160209] loop: module loaded
[ 0.160248] tun: Universal TUN/TAP device driver, 1.6
[ 0.160285] tun: (C) 1999-2004 Max Krasnyansky <maxk@qualcomm.com>
[ 0.160413] usbcore: registered new interface driver rtl8187
[ 0.160496] ACPI: PCI Interrupt 0000:01:01.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 0.160607] ath5k_pci 0000:01:01.0: registered as 'phy0'
[ 0.247392] phy0: Selected rate control algorithm 'pid'
[ 0.247945] ath5k phy0: Atheros AR5213A chip found (MAC: 0x79, PHY: 0x45)
[ 0.247975] ath5k phy0: RF2112A 2GHz radio found (0x56)
[ 0.248110] usbcore: registered new interface driver irda-usb
[ 0.248155] USB IrDA support registered
[ 0.248235] usbcore: registered new interface driver stir4200
[ 0.249025] usbcore: registered new interface driver mcs7780
[ 0.249577] Driver 'sd' needs updating - please use bus_type methods
[ 0.249659] Driver 'sr' needs updating - please use bus_type methods
[ 0.249797] ahci 0000:00:1f.2: version 3.0
[ 0.249816] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 23 (level, low) -> IRQ 23
[ 0.249954] ahci 0000:00:1f.2: enabling ASUS P5W DH Deluxe on-board SIMG4726 workaround
[ 1.251847] ahci 0000:00:1f.2: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
[ 1.251900] ahci 0000:00:1f.2: flags: 64bit ncq led clo pio slum part
[ 1.251945] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 1.252209] scsi0 : ahci
[ 1.252333] scsi1 : ahci
[ 1.252451] scsi2 : ahci
[ 1.252572] scsi3 : ahci
[ 1.252675] ata1: SATA max UDMA/133 abar m1024@0xefffb800 port 0xefffb900 irq 1274
[ 1.252722] ata2: SATA max UDMA/133 irq_stat 0x00400040, connection status changed irq 1274
[ 1.252770] ata3: SATA max UDMA/133 abar m1024@0xefffb800 port 0xefffba00 irq 1274
[ 1.252817] ata4: SATA max UDMA/133 abar m1024@0xefffb800 port 0xefffba80 irq 1274
[ 1.709762] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 1.867728] ata1.00: ATA-7: WDC WD740ADFD-00NLR1, 20.07P20, max UDMA/133
[ 1.867731] ata1.00: 145226112 sectors, multi 16: LBA48 NCQ (not used)
[ 1.870342] ata1.00: configured for UDMA/133
[ 4.783300] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 4.783408] ata2.00: ATA-6: Config Disk, RGL10364, max UDMA/133
[ 4.783459] ata2.00: 640 sectors, multi 1: LBA
[ 4.783500] ata2.00: device is on DMA blacklist, disabling DMA
[ 4.783628] ata2.00: configured for PIO4
[ 5.086252] ata3: SATA link down (SStatus 0 SControl 300)
[ 5.389205] ata4: SATA link down (SStatus 0 SControl 300)
[ 5.233616] scsi 0:0:0:0: Direct-Access ATA WDC WD740ADFD-00 20.0 PQ: 0 ANSI: 5
[ 5.233995] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
[ 5.234050] sd 0:0:0:0: [sda] Write Protect is off
[ 5.234087] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.234115] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.234446] sd 0:0:0:0: [sda] 145226112 512-byte hardware sectors (74356 MB)
[ 5.234499] sd 0:0:0:0: [sda] Write Protect is off
[ 5.234537] sd 0:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 5.234564] sd 0:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 5.234627] sda: sda1 sda2 sda3
[ 5.399058] sd 0:0:0:0: [sda] Attached SCSI disk
[ 5.399234] sd 0:0:0:0: Attached scsi generic sg0 type 0
[ 5.399410] scsi 1:0:0:0: Direct-Access ATA Config Disk RGL1 PQ: 0 ANSI: 5
[ 5.399608] sd 1:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
[ 5.399661] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.399698] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.399726] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 5.399856] sd 1:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
[ 5.399909] sd 1:0:0:0: [sdb] Write Protect is off
[ 5.399946] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 5.399974] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 5.400024] sdb: unknown partition table
[ 5.400270] sd 1:0:0:0: [sdb] Attached SCSI disk
[ 5.400448] sd 1:0:0:0: Attached scsi generic sg1 type 0
[ 5.400526] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 6.401076] ahci 0000:02:00.0: AHCI 0001.0000 32 slots 2 ports 3 Gbps 0x3 impl SATA mode
[ 6.401128] ahci 0000:02:00.0: flags: 64bit ncq pm led clo pmp pio slum part
[ 6.401176] PCI: Setting latency timer of device 0000:02:00.0 to 64
[ 6.401299] scsi4 : ahci
[ 6.401423] scsi5 : ahci
[ 6.401546] ata5: SATA max UDMA/133 abar m8192@0xebbfe000 port 0xebbfe100 irq 17
[ 6.401594] ata6: SATA max UDMA/133 abar m8192@0xebbfe000 port 0xebbfe180 irq 17
[ 6.551041] ata5: SATA link down (SStatus 0 SControl 300)
[ 6.856995] ata6: SATA link down (SStatus 0 SControl 300)
[ 7.013103] ata_piix 0000:00:1f.1: version 2.12
[ 7.013109] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 22 (level, low) -> IRQ 22
[ 7.013208] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 7.013265] scsi6 : ata_piix
[ 7.013386] scsi7 : ata_piix
[ 7.015047] ata7: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0xffa0 irq 14
[ 7.015087] ata8: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0xffa8 irq 15
[ 7.178262] ata7.00: ATAPI: PLEXTOR DVD-ROM PX-130A, 1.03, max UDMA/33
[ 7.338169] ata7.00: configured for UDMA/33
[ 7.657279] scsi 6:0:0:0: CD-ROM PLEXTOR DVD-ROM PX-130A 1.03 PQ: 0 ANSI: 5
[ 7.660894] sr0: scsi3-mmc drive: 0x/50x cd/rw xa/form2 cdda tray
[ 7.660938] Uniform CD-ROM driver Revision: 3.20
[ 7.661173] sr 6:0:0:0: Attached scsi CD-ROM sr0
[ 7.661270] sr 6:0:0:0: Attached scsi generic sg2 type 5
[ 7.661411] PCI: Enabling device 0000:02:00.1 (0000 -> 0001)
[ 7.661454] ACPI: PCI Interrupt 0000:02:00.1[B] -> GSI 18 (level, low) -> IRQ 18
[ 7.661553] PCI: Setting latency timer of device 0000:02:00.1 to 64
[ 7.661606] scsi8 : pata_jmicron
[ 7.661729] scsi9 : pata_jmicron
[ 7.662573] ata9: PATA max UDMA/100 cmd 0x9c00 ctl 0x9880 bmdma 0x9400 irq 18
[ 7.662613] ata10: PATA max UDMA/100 cmd 0x9800 ctl 0x9480 bmdma 0x9408 irq 18
[ 7.977334] I2O subsystem v1.325
[ 7.977370] i2o: max drivers = 8
[ 7.977596] Fusion MPT base driver 3.04.06
[ 7.977633] Copyright (c) 1999-2007 LSI Corporation
[ 7.977678] Fusion MPT SPI Host driver 3.04.06
[ 7.977867] Fusion MPT SAS Host driver 3.04.06
[ 7.978056] ACPI: PCI Interrupt 0000:01:03.0[A] -> GSI 21 (level, low) -> IRQ 21
[ 8.034804] firewire_ohci: Added fw-ohci device 0000:01:03.0, OHCI version 1.10
[ 8.035439] ieee1394: raw1394: /dev/raw1394 device initialized
[ 8.035664] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 20 (level, low) -> IRQ 20
[ 8.035743] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 8.035747] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 8.036352] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 1
[ 8.040320] ehci_hcd 0000:00:1d.7: debug port 1
[ 8.040361] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 8.040370] ehci_hcd 0000:00:1d.7: irq 20, io mem 0xefffbc00
[ 8.049803] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 8.050205] usb usb1: configuration #1 chosen from 1 choice
[ 8.050333] hub 1-0:1.0: USB hub found
[ 8.050395] hub 1-0:1.0: 8 ports detected
[ 8.150986] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 8.151029] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.151075] usb usb1: Product: EHCI Host Controller
[ 8.151112] usb usb1: Manufacturer: Linux 2.6.25-unpatched ehci_hcd
[ 8.151150] usb usb1: SerialNumber: 0000:00:1d.7
[ 8.151242] ohci_hcd: 2006 August 04 USB 1.1 'Open' Host Controller (OHCI) Driver
[ 8.151299] USB Universal Host Controller Interface driver v3.0
[ 8.151361] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 20 (level, low) -> IRQ 20
[ 8.151437] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 8.151440] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 8.151614] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 8.151681] uhci_hcd 0000:00:1d.0: irq 20, io base 0x0000e480
[ 8.151911] usb usb2: configuration #1 chosen from 1 choice
[ 8.152009] hub 2-0:1.0: USB hub found
[ 8.152072] hub 2-0:1.0: 2 ports detected
[ 8.252914] usb usb2: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.252954] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.253000] usb usb2: Product: UHCI Host Controller
[ 8.253037] usb usb2: Manufacturer: Linux 2.6.25-unpatched uhci_hcd
[ 8.253076] usb usb2: SerialNumber: 0000:00:1d.0
[ 8.253132] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 17 (level, low) -> IRQ 17
[ 8.253208] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 8.253211] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 8.253378] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 3
[ 8.253444] uhci_hcd 0000:00:1d.1: irq 17, io base 0x0000e800
[ 8.253682] usb usb3: configuration #1 chosen from 1 choice
[ 8.253772] hub 3-0:1.0: USB hub found
[ 8.253815] hub 3-0:1.0: 2 ports detected
[ 8.354880] usb usb3: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.354931] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.354977] usb usb3: Product: UHCI Host Controller
[ 8.355014] usb usb3: Manufacturer: Linux 2.6.25-unpatched uhci_hcd
[ 8.355052] usb usb3: SerialNumber: 0000:00:1d.1
[ 8.355107] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 8.355183] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 8.355186] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 8.355356] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 4
[ 8.355422] uhci_hcd 0000:00:1d.2: irq 18, io base 0x0000e880
[ 8.355657] usb usb4: configuration #1 chosen from 1 choice
[ 8.355748] hub 4-0:1.0: USB hub found
[ 8.355757] hub 4-0:1.0: 2 ports detected
[ 8.186803] usb 1-1: new high speed USB device using ehci_hcd and address 2
[ 8.456866] usb usb4: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.456918] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.456964] usb usb4: Product: UHCI Host Controller
[ 8.457001] usb usb4: Manufacturer: Linux 2.6.25-unpatched uhci_hcd
[ 8.457040] usb usb4: SerialNumber: 0000:00:1d.2
[ 8.457096] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 19 (level, low) -> IRQ 19
[ 8.457173] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 8.457176] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 8.457346] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 5
[ 8.457417] uhci_hcd 0000:00:1d.3: irq 19, io base 0x0000ec00
[ 8.457648] usb usb5: configuration #1 chosen from 1 choice
[ 8.457739] hub 5-0:1.0: USB hub found
[ 8.457782] hub 5-0:1.0: 2 ports detected
[ 8.475536] usb 1-1: configuration #1 chosen from 1 choice
[ 8.475844] hub 1-1:1.0: USB hub found
[ 8.476142] hub 1-1:1.0: 4 ports detected
[ 8.535022] firewire_core: created device fw0: GUID 0011d80000eaf58e, S400
[ 8.558866] usb usb5: New USB device found, idVendor=1d6b, idProduct=0001
[ 8.558905] usb usb5: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 8.558952] usb usb5: Product: UHCI Host Controller
[ 8.558989] usb usb5: Manufacturer: Linux 2.6.25-unpatched uhci_hcd
[ 8.559028] usb usb5: SerialNumber: 0000:00:1d.3
[ 8.577864] usb 1-1: New USB device found, idVendor=05e3, idProduct=0605
[ 8.577904] usb 1-1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 8.577943] usb 1-1: Product: USB2.0 Hub
[ 9.505588] usb 1-7: new high speed USB device using ehci_hcd and address 7
[ 9.621075] usb 1-7: configuration #1 chosen from 1 choice
[ 9.621450] hub 1-7:1.0: USB hub found
[ 9.621682] hub 1-7:1.0: 4 ports detected
[ 9.723672] usb 1-7: New USB device found, idVendor=05e3, idProduct=0606
[ 9.723723] usb 1-7: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 9.723762] usb 1-7: Product: USB2.0 Hub
[ 10.033507] usb 2-2: new low speed USB device using uhci_hcd and address 2
[ 10.193953] usb 2-2: configuration #1 chosen from 1 choice
[ 10.196769] usb 2-2: New USB device found, idVendor=046d, idProduct=c50e
[ 10.196808] usb 2-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 10.196847] usb 2-2: Product: USB RECEIVER
[ 10.196883] usb 2-2: Manufacturer: Logitech
[ 10.402450] usb 3-1: new low speed USB device using uhci_hcd and address 2
[ 10.561963] usb 3-1: configuration #1 chosen from 1 choice
[ 10.564866] usb 3-1: New USB device found, idVendor=1130, idProduct=cc00
[ 10.564910] usb 3-1: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 10.564960] usb 3-1: Product: ASUS DH Remote
[ 10.564997] usb 3-1: Manufacturer: T-wins
[ 10.770395] usb 3-2: new full speed USB device using uhci_hcd and address 3
[ 10.939073] usb 3-2: configuration #1 chosen from 1 choice
[ 10.941846] hub 3-2:1.0: USB hub found
[ 10.943715] hub 3-2:1.0: 3 ports detected
[ 11.049489] usb 3-2: New USB device found, idVendor=046d, idProduct=0b04
[ 11.049529] usb 3-2: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 11.049568] usb 3-2: Product: Logitech BT Mini-Receiver
[ 11.049605] usb 3-2: Manufacturer: Logitech
[ 11.255321] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 11.408301] usb 4-1: configuration #1 chosen from 1 choice
[ 11.411533] usb 4-1: New USB device found, idVendor=057c, idProduct=3800
[ 11.411572] usb 4-1: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.411611] usb 4-1: Product: Bluetooth Device
[ 11.411648] usb 4-1: Manufacturer: Bluetooth Device
[ 11.411685] usb 4-1: SerialNumber: DE80890E0400
[ 11.693522] usb 1-1.2: new high speed USB device using ehci_hcd and address 8
[ 11.770215] usb 1-1.2: configuration #1 chosen from 1 choice
[ 11.770744] usb 1-1.2: New USB device found, idVendor=04a9, idProduct=10a5
[ 11.770784] usb 1-1.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 11.770831] usb 1-1.2: Product: iP5200
[ 11.770867] usb 1-1.2: Manufacturer: Canon
[ 11.770903] usb 1-1.2: SerialNumber: 513B8C
[ 11.937532] usb 1-1.4: new full speed USB device using ehci_hcd and address 9
[ 12.015380] usb 1-1.4: configuration #1 chosen from 1 choice
[ 12.017084] usb 1-1.4: New USB device found, idVendor=046d, idProduct=c525
[ 12.017123] usb 1-1.4: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 12.017170] usb 1-1.4: Product: USB Receiver
[ 12.017195] usb 1-1.4: Manufacturer: Logitech
[ 12.183440] usb 1-7.1: new high speed USB device using ehci_hcd and address 10
[ 12.269580] usb 1-7.1: configuration #1 chosen from 1 choice
[ 12.269945] hub 1-7.1:1.0: USB hub found
[ 12.270183] hub 1-7.1:1.0: 4 ports detected
[ 12.372291] usb 1-7.1: New USB device found, idVendor=05e3, idProduct=0608
[ 12.372331] usb 1-7.1: New USB device strings: Mfr=0, Product=1, SerialNumber=0
[ 12.372377] usb 1-7.1: Product: USB2.0 Hub
[ 12.550361] usb 1-7.2: new high speed USB device using ehci_hcd and address 11
[ 12.629233] usb 1-7.2: configuration #1 chosen from 1 choice
[ 12.630019] usb 1-7.2: New USB device found, idVendor=05e3, idProduct=070e
[ 12.630059] usb 1-7.2: New USB device strings: Mfr=0, Product=1, SerialNumber=2
[ 12.630102] usb 1-7.2: Product: USB Storage
[ 12.630105] usb 1-7.2: SerialNumber: 000000009602
[ 12.797310] usb 1-7.3: new high speed USB device using ehci_hcd and address 12
[ 12.878632] usb 1-7.3: configuration #1 chosen from 1 choice
[ 13.025621] phy1: Selected rate control algorithm 'pid'
[ 13.026099] phy1: hwaddr 00:15:af:09:e6:34, rtl8187 V1 + rtl8225z2
[ 13.026909] usb 1-7.3: New USB device found, idVendor=0bda, idProduct=8187
[ 13.026949] usb 1-7.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 13.026996] usb 1-7.3: Product: RTL8187_Wireless
[ 13.027033] usb 1-7.3: Manufacturer: Manufacturer_Realtek_RTL8187_
[ 13.027045] usb 1-7.3: SerialNumber: 0015AF09E634
[ 13.204325] usb 3-2.2: new full speed USB device using uhci_hcd and address 4
[ 13.345439] usb 3-2.2: configuration #1 chosen from 1 choice
[ 13.351246] usb 3-2.2: New USB device found, idVendor=046d, idProduct=c713
[ 13.351286] usb 3-2.2: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 13.351334] usb 3-2.2: Product: Logitech BT Mini-Receiver
[ 13.351372] usb 3-2.2: Manufacturer: Logitech
[ 13.351410] usb 3-2.2: SerialNumber: 0007617AAFA5
[ 13.527378] usb 3-2.3: new full speed USB device using uhci_hcd and address 5
[ 13.668432] usb 3-2.3: configuration #1 chosen from 1 choice
[ 13.674218] usb 3-2.3: New USB device found, idVendor=046d, idProduct=c714
[ 13.674953] usb 3-2.3: New USB device strings: Mfr=1, Product=2, SerialNumber=3
[ 13.675006] usb 3-2.3: Product: Logitech BT Mini-Receiver
[ 13.675044] usb 3-2.3: Manufacturer: Logitech
[ 13.675082] usb 3-2.3: SerialNumber: 0007617AAFA5
[ 13.676146] usblp0: USB Bidirectional printer dev 8 if 0 alt 0 proto 2 vid 0x04A9 pid 0x10A5
[ 13.677095] usbcore: registered new interface driver usblp
[ 13.677136] Initializing USB Mass Storage driver...
[ 13.677251] scsi10 : SCSI emulation for USB Mass Storage devices
[ 13.506441] usb-storage: device found at 11
[ 13.506443] usb-storage: waiting for device to settle before scanning
[ 13.677436] usbcore: registered new interface driver usb-storage
[ 13.677477] USB Mass Storage support registered.
[ 13.677626] usbcore: registered new interface driver usbserial
[ 13.677707] drivers/usb/serial/usb-serial.c: USB Serial support registered for generic
[ 13.677865] usbcore: registered new interface driver usbserial_generic
[ 13.677905] drivers/usb/serial/usb-serial.c: USB Serial Driver core
[ 13.677983] drivers/usb/serial/usb-serial.c: USB Serial support registered for Handspring Visor / Palm OS
[ 13.678081] drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 3.5
[ 13.678169] drivers/usb/serial/usb-serial.c: USB Serial support registered for Sony Clie 5.0
[ 13.678284] usbcore: registered new interface driver visor
[ 13.678323] drivers/usb/serial/visor.c: USB HandSpring Visor / Palm OS driver
[ 13.678544] PNP: No PS/2 controller found. Probing ports directly.
[ 13.681165] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 13.681219] serio: i8042 AUX port at 0x60,0x64 irq 12
[ 13.681410] mice: PS/2 mouse device common for all mice
[ 13.732832] i2c /dev entries driver
[ 13.733031] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 23 (level, low) -> IRQ 23
[ 13.753094] coretemp coretemp.0: Using relative temperature scale!
[ 13.753288] coretemp coretemp.1: Using relative temperature scale!
[ 13.768994] w83627ehf: Found W83627DHG chip at 0x290
[ 13.769486] md: raid0 personality registered for level 0
[ 13.769650] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 13.769698] Bluetooth: HCI USB driver ver 2.9
[ 13.771669] usbcore: registered new interface driver hci_usb
[ 13.771710] Bluetooth: Virtual HCI driver ver 1.2
[ 13.771803] Bluetooth: HCI UART driver ver 2.2
[ 13.771842] Bluetooth: HCI H4 protocol initialized
[ 13.771880] Bluetooth: HCI BCSP protocol initialized
[ 13.771918] Bluetooth: Broadcom Blutonium firmware driver ver 1.1
[ 13.771993] usbcore: registered new interface driver bcm203x
[ 13.772034] Bluetooth: Digianswer Bluetooth USB driver ver 0.9
[ 13.772136] usbcore: registered new interface driver bpa10x
[ 13.772177] Bluetooth: BlueFRITZ! USB driver ver 1.1
[ 13.772271] usbcore: registered new interface driver bfusb
[ 13.772461] usbcore: registered new interface driver hiddev
[ 13.790242] input: Logitech USB RECEIVER as /devices/pci0000:00/0000:00:1d.0/usb2/2-2/2-2:1.0/input/input2
[ 13.800094] input,hidraw0: USB HID v1.11 Mouse [Logitech USB RECEIVER] on usb-0000:00:1d.0-2
[ 13.809518] hiddev96hidraw1: USB HID v1.10 Device [T-wins ASUS DH Remote] on usb-0000:00:1d.1-1
[ 13.810934] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4:1.0/input/input3
[ 13.821075] input,hidraw2: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:1d.7-1.4
[ 13.823425] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:1d.7/usb1/1-1/1-1.4/1-1.4:1.1/input/input4
[ 13.831126] input,hiddev97,hidraw3: USB HID v1.11 Device [Logitech USB Receiver] on usb-0000:00:1d.7-1.4
[ 13.836792] input: Logitech Logitech BT Mini-Receiver as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2.2/3-2.2:1.0/input/input5
[ 13.844074] input,hidraw4: USB HID v1.11 Keyboard [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1d.1-2.2
[ 13.853446] input: Logitech Logitech BT Mini-Receiver as /devices/pci0000:00/0000:00:1d.1/usb3/3-2/3-2.3/3-2.3:1.0/input/input6
[ 13.866123] input,hiddev98,hidraw5: USB HID v1.11 Mouse [Logitech Logitech BT Mini-Receiver] on usb-0000:00:1d.1-2.3
[ 13.866369] usbcore: registered new interface driver usbhid
[ 13.866409] drivers/hid/usbhid/hid-core.c: v2.6:USB HID core driver
[ 13.866520] oprofile: using NMI interrupt.
[ 13.867355] TCP cubic registered
[ 13.867475] NET: Registered protocol family 1
[ 13.867649] NET: Registered protocol family 10
[ 13.870521] IPv6 over IPv4 tunneling driver
[ 13.871623] NET: Registered protocol family 17
[ 13.872805] IrCOMM protocol (Dag Brattli)
[ 13.874938] Bluetooth: L2CAP ver 2.9
[ 13.874975] Bluetooth: L2CAP socket layer initialized
[ 13.875015] Bluetooth: SCO (Voice Link) ver 0.5
[ 13.875052] Bluetooth: SCO socket layer initialized
[ 13.875123] Bluetooth: RFCOMM socket layer initialized
[ 13.875166] Bluetooth: RFCOMM TTY layer initialized
[ 13.875204] Bluetooth: RFCOMM ver 1.8
[ 13.875240] Bluetooth: BNEP (Ethernet Emulation) ver 1.2
[ 13.875278] Bluetooth: BNEP filters: protocol multicast
[ 13.875317] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 13.875664] RPC: Registered udp transport module.
[ 13.875702] RPC: Registered tcp transport module.
[ 13.875838] NET: Registered protocol family 33
[ 13.876034] RxRPC: Registered security type 2 'rxkad'
[ 13.876073] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 13.876111] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 13.876164] ieee80211_crypt: registered algorithm 'NULL'
[ 13.876166] ieee80211_crypt: registered algorithm 'WEP'
[ 13.876168] ieee80211_crypt: registered algorithm 'CCMP'
[ 13.876169] ieee80211_crypt: registered algorithm 'TKIP'
[ 13.876613] drivers/rtc/hctosys.c: unable to open rtc device (rtc0)
[ 13.876996] md: Autodetecting RAID arrays.
[ 13.877033] md: Scanned 0 and added 0 devices.
[ 13.877070] md: autorun ...
[ 13.877105] md: ... autorun DONE.
[ 13.721579] kjournald starting. Commit interval 5 seconds
[ 13.892664] EXT3-fs: mounted filesystem with ordered data mode.
[ 13.892755] VFS: Mounted root (ext3 filesystem) readonly.
[ 13.892805] Freeing unused kernel memory: 384k freed
[ 15.601789] udev: renamed network interface wlan0 to wlan1
[ 15.789066] udev: renamed network interface wlan1_rename to wlan0
[ 16.112060] nvidia: module license 'NVIDIA' taints kernel.
[ 16.306558] ACPI: PCI Interrupt 0000:04:00.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 16.306570] PCI: Setting latency timer of device 0000:04:00.0 to 64
[ 16.306595] sky2 0000:04:00.0: v1.21 addr 0xebdfc000 irq 19 Yukon-EC (0xb6) rev 2
[ 16.307727] sky2 eth0: addr 00:18:f3:84:4f:8a
[ 16.307748] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 16.307755] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 16.307775] sky2 0000:03:00.0: v1.21 addr 0xebcfc000 irq 16 Yukon-EC (0xb6) rev 2
[ 16.308917] sky2 eth1: addr 00:18:f3:84:43:74
[ 16.412061] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 16.412079] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 16.367041] ACPI: PCI Interrupt 0000:06:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 16.367049] PCI: Setting latency timer of device 0000:06:00.0 to 64
[ 16.367394] NVRM: loading NVIDIA UNIX x86_64 Kernel Module 169.12 Thu Feb 14 17:51:09 PST 2008
[ 17.737686] EXT3 FS on sda3, internal journal
[ 18.048787] Adding 979956k swap on /dev/sda2. Priority:-1 extents:1 across:979956k
[ 18.507401] scsi 10:0:0:0: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
[ 18.508885] sd 10:0:0:0: [sdc] Attached SCSI removable disk
[ 18.508927] sd 10:0:0:0: Attached scsi generic sg3 type 0
[ 18.509648] scsi 10:0:0:1: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
[ 18.511200] sd 10:0:0:1: [sdd] Attached SCSI removable disk
[ 18.511243] sd 10:0:0:1: Attached scsi generic sg4 type 0
[ 18.512304] scsi 10:0:0:2: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
[ 18.513695] sd 10:0:0:2: [sde] Attached SCSI removable disk
[ 18.513732] sd 10:0:0:2: Attached scsi generic sg5 type 0
[ 18.514398] scsi 10:0:0:3: Direct-Access Generic STORAGE DEVICE 9602 PQ: 0 ANSI: 0
[ 18.515566] sd 10:0:0:3: [sdf] Attached SCSI removable disk
[ 18.515602] sd 10:0:0:3: Attached scsi generic sg6 type 0
[ 18.515927] usb-storage: device scan complete
[ 23.174007] ADDRCONF(NETDEV_UP): wlan0: link is not ready
[ 23.003080] sky2 eth1: enabling interface
[ 23.006080] ADDRCONF(NETDEV_UP): eth1: link is not ready
[ 23.177037] sky2 eth0: enabling interface
[ 23.179215] ADDRCONF(NETDEV_UP): eth0: link is not ready
[ 25.406380] wlan0: Initial auth_alg=0
[ 25.406388] wlan0: authenticate with AP 00:0f:b5:f8:2b:7e
[ 25.408434] wlan0: RX authentication from 00:0f:b5:f8:2b:7e (alg=0 transaction=2 status=0)
[ 25.408439] wlan0: authenticated
[ 25.408443] wlan0: associate with AP 00:0f:b5:f8:2b:7e
[ 25.410869] wlan0: RX AssocResp from 00:0f:b5:f8:2b:7e (capab=0x431 status=0 aid=2)
[ 25.410874] wlan0: associated
[ 25.410879] wlan0: switched to short barker preamble (BSSID=00:0f:b5:f8:2b:7e)
[ 25.411170] ADDRCONF(NETDEV_CHANGE): wlan0: link becomes ready
[ 25.522160] sky2 eth0: Link is up at 1000 Mbps, full duplex, flow control both
[ 25.522303] ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready
[ 27.194668] ata2.00: exception Emask 0x10 SAct 0x0 SErr 0x10000 action 0xa frozen
[ 27.194674] ata2.00: irq_stat 0x00400000, PHY RDY changed
[ 27.194677] ata2: SError: { PHYRdyChg }
[ 27.194684] ata2.00: cmd c4/00:08:80:01:00/00:00:00:00:00/e0 tag 0 pio 4096 in
[ 27.194685] res 50/00:00:01:01:80/00:00:00:00:00/a0 Emask 0x10 (ATA bus error)
[ 27.194689] ata2.00: status: { DRDY }
[ 27.194697] ata2: hard resetting link
[ 27.916803] ata2: SATA link down (SStatus 0 SControl 300)
[ 27.916813] ata2: failed to recover some devices, retrying in 5 secs
[ 32.917045] ata2: hard resetting link
[ 33.222000] ata2: SATA link down (SStatus 0 SControl 300)
[ 33.222007] ata2: failed to recover some devices, retrying in 5 secs
[ 35.785606] eth0: no IPv6 routers present
[ 35.923584] wlan0: no IPv6 routers present
[ 38.222244] ata2: hard resetting link
[ 39.551895] NVRM: bad caching on address 0xffff81007bca6000: actual 0x173 != expected 0x17b
[ 39.551898] NVRM: please see the README section on Cache Aliasing for more information
[ 39.551904] NVRM: bad caching on address 0xffff81007bca7000: actual 0x173 != expected 0x17b
[ 40.409875] NVRM: bad caching on address 0xffff81007ad90000: actual 0x173 != expected 0x17b
[ 40.410033] NVRM: bad caching on address 0xffff81007ad93000: actual 0x173 != expected 0x17b
[ 40.410109] NVRM: bad caching on address 0xffff81007ad9d000: actual 0x173 != expected 0x17b
[ 40.410181] NVRM: bad caching on address 0xffff81007ad92000: actual 0x173 != expected 0x17b
[ 40.410253] NVRM: bad caching on address 0xffff81007ad9a000: actual 0x173 != expected 0x17b
[ 40.410325] NVRM: bad caching on address 0xffff81007ad9b000: actual 0x173 != expected 0x17b
[ 40.410397] NVRM: bad caching on address 0xffff81007ad86000: actual 0x173 != expected 0x17b
[ 40.410468] NVRM: bad caching on address 0xffff81007ad9e000: actual 0x173 != expected 0x17b
[ 40.680697] ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
[ 40.680856] ata2.00: device is on DMA blacklist, disabling DMA
[ 40.680988] ata2.00: configured for PIO4
[ 40.680998] ata2: exception Emask 0x10 SAct 0x0 SErr 0x0 action 0x9 t4
[ 40.681000] ata2: irq_stat 0x00000040, connection status changed
[ 40.681173] ata2.00: device is on DMA blacklist, disabling DMA
[ 40.681301] ata2.00: configured for PIO4
[ 40.681307] ata2: EH complete
[ 40.510431] sd 1:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
[ 40.510444] sd 1:0:0:0: [sdb] Write Protect is off
[ 40.510446] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 40.510466] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
[ 40.510487] sd 1:0:0:0: [sdb] 640 512-byte hardware sectors (0 MB)
[ 40.510498] sd 1:0:0:0: [sdb] Write Protect is off
[ 40.510500] sd 1:0:0:0: [sdb] Mode Sense: 00 3a 00 00
[ 40.510520] sd 1:0:0:0: [sdb] Write cache: disabled, read cache: enabled, doesn't support DPO or FUA
^ permalink raw reply [flat|nested] only message in thread
only message in thread, other threads:[~2008-04-22 21:41 UTC | newest]
Thread overview: (only message) (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-04-22 21:41 Config Disk, RGL10364 device is on DMA blacklist Bjoern Olausson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®