* [PATCH] ARM: dts: sunxi: Use the axp209 driver on the olimex lime2 @ 2015-08-09 19:02 Olliver Schinagl 2015-08-09 19:02 ` [PATCH] ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 Olliver Schinagl 0 siblings, 1 reply; 4+ messages in thread From: Olliver Schinagl @ 2015-08-09 19:02 UTC (permalink / raw) To: Maxime Ripard Cc: Olliver Schinagl, dev, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King, devicetree, linux-arm-kernel, linux-kernel, Olliver Schinagl This patch enables usage of the axp209 on the OLinuXino Lime2 and was tested the OLinuXino Lime2-4GB. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> Olliver Schinagl (1): ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 131 ++++++++++++++---------- 1 file changed, 75 insertions(+), 56 deletions(-) -- 2.1.4 ^ permalink raw reply [flat|nested] 4+ messages in thread
* [PATCH] ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 2015-08-09 19:02 [PATCH] ARM: dts: sunxi: Use the axp209 driver on the olimex lime2 Olliver Schinagl @ 2015-08-09 19:02 ` Olliver Schinagl 2015-08-09 23:05 ` [linux-sunxi] " Iain Paton 0 siblings, 1 reply; 4+ messages in thread From: Olliver Schinagl @ 2015-08-09 19:02 UTC (permalink / raw) To: Maxime Ripard Cc: Olliver Schinagl, dev, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King, devicetree, linux-arm-kernel, linux-kernel, Olliver Schinagl, Olliver Schinagl From: Olliver Schinagl <o.schinagl@ultimaker.com> This patch enables the musb-otg USB controller on the Lime2. The Lime2 differs from the Lime1 series in pins used for usb0 power. Tested on a OlinuXino Lime2-4GB. Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> --- arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 131 ++++++++++++++---------- 1 file changed, 75 insertions(+), 56 deletions(-) diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts index 22cd052..efd9ebb 100644 --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts @@ -71,14 +71,6 @@ default-state = "on"; }; }; - - reg_axp_ipsout: axp_ipsout { - compatible = "regulator-fixed"; - regulator-name = "axp-ipsout"; - regulator-min-microvolt = <5000000>; - regulator-max-microvolt = <5000000>; - regulator-always-on; - }; }; &ahci { @@ -86,6 +78,10 @@ status = "okay"; }; +&cpu0 { + cpu-supply = <®_dcdc2>; +}; + &ehci0 { status = "okay"; }; @@ -112,57 +108,9 @@ status = "okay"; axp209: pmic@34 { - compatible = "x-powers,axp209"; reg = <0x34>; interrupt-parent = <&nmi_intc>; interrupts = <0 IRQ_TYPE_LEVEL_LOW>; - - interrupt-controller; - #interrupt-cells = <1>; - - acin-supply = <®_axp_ipsout>; - vin2-supply = <®_axp_ipsout>; - vin3-supply = <®_axp_ipsout>; - ldo24in-supply = <®_axp_ipsout>; - ldo3in-supply = <®_axp_ipsout>; - - regulators { - vdd_rtc: ldo1 { - regulator-min-microvolt = <1300000>; - regulator-max-microvolt = <1300000>; - regulator-always-on; - }; - - avcc: ldo2 { - regulator-min-microvolt = <1800000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vcc_csi0: ldo3 { - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <3500000>; - regulator-always-on; - }; - - vcc_csi1: ldo4 { - regulator-min-microvolt = <1250000>; - regulator-max-microvolt = <3300000>; - regulator-always-on; - }; - - vdd_cpu: dcdc2 { - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <2275000>; - regulator-always-on; - }; - - vdd_int: dcdc3 { - regulator-min-microvolt = <700000>; - regulator-max-microvolt = <3500000>; - regulator-always-on; - }; - }; }; }; @@ -196,6 +144,10 @@ status = "okay"; }; +&otg_sram { + status = "okay"; +}; + &pio { ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { allwinner,pins = "PC3"; @@ -210,6 +162,27 @@ allwinner,drive = <SUN4I_PINCTRL_20_MA>; allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; }; + + usb0_id_detect_pin: usb0_id_detect_pin@0 { + allwinner,pins = "PH4"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; + }; + + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { + allwinner,pins = "PH5"; + allwinner,function = "gpio_in"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; + }; + + usb0_vbus_pin_lime2: usb0_vbus_pin@0 { + allwinner,pins = "PC17"; + allwinner,function = "gpio_out"; + allwinner,drive = <SUN4I_PINCTRL_10_MA>; + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; + }; }; ®_ahci_5v { @@ -218,6 +191,42 @@ status = "okay"; }; +#include "axp209.dtsi" + +®_dcdc2 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1450000>; + regulator-name = "vdd-cpu"; +}; + +®_dcdc3 { + regulator-always-on; + regulator-min-microvolt = <1000000>; + regulator-max-microvolt = <1400000>; + regulator-name = "vdd-int-dll"; +}; + +®_ldo1 { + regulator-always-on; + regulator-min-microvolt = <1300000>; + regulator-max-microvolt = <1300000>; + regulator-name = "vdd-rtc"; +}; + +®_ldo2 { + regulator-always-on; + regulator-min-microvolt = <3000000>; + regulator-max-microvolt = <3000000>; + regulator-name = "avcc"; +}; + +®_usb0_vbus { + pinctrl-0 = <&usb0_vbus_pin_lime2>; + gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>; + status = "okay"; +}; + ®_usb1_vbus { status = "okay"; }; @@ -232,7 +241,17 @@ status = "okay"; }; +&usb_otg { + dr_mode = "otg"; + status = "okay"; +}; + &usbphy { + pinctrl-names = "default"; + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ + usb0_vbus-supply = <®_usb0_vbus>; usb1_vbus-supply = <®_usb1_vbus>; usb2_vbus-supply = <®_usb2_vbus>; status = "okay"; -- 2.1.4 ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [linux-sunxi] [PATCH] ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 2015-08-09 19:02 ` [PATCH] ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 Olliver Schinagl @ 2015-08-09 23:05 ` Iain Paton 2015-08-10 8:43 ` Olliver Schinagl 0 siblings, 1 reply; 4+ messages in thread From: Iain Paton @ 2015-08-09 23:05 UTC (permalink / raw) To: oliver Cc: Maxime Ripard, Olliver Schinagl, dev, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King, devicetree, linux-arm-kernel, linux-kernel, Olliver Schinagl NAK. This does much more than enabling the otg port. Neither wholesale re-writing the regulator node or hooking up the dcdc2 regulator to the operating points definition is required in order to enable the otg port. At the very least you need to split your patches and describe them properly rather than trying to get additional changes that are likely to cause further discussion through unnoticed using a misleading subject. Rgds, Iain On 09/08/15 20:02, Olliver Schinagl wrote: > From: Olliver Schinagl <o.schinagl@ultimaker.com> > > This patch enables the musb-otg USB controller on the Lime2. The Lime2 > differs from the Lime1 series in pins used for usb0 power. > > Tested on a OlinuXino Lime2-4GB. > > Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> > --- > arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 131 ++++++++++++++---------- > 1 file changed, 75 insertions(+), 56 deletions(-) > > diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts > index 22cd052..efd9ebb 100644 > --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts > +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts > @@ -71,14 +71,6 @@ > default-state = "on"; > }; > }; > - > - reg_axp_ipsout: axp_ipsout { > - compatible = "regulator-fixed"; > - regulator-name = "axp-ipsout"; > - regulator-min-microvolt = <5000000>; > - regulator-max-microvolt = <5000000>; > - regulator-always-on; > - }; > }; > > &ahci { > @@ -86,6 +78,10 @@ > status = "okay"; > }; > > +&cpu0 { > + cpu-supply = <®_dcdc2>; > +}; > + > &ehci0 { > status = "okay"; > }; > @@ -112,57 +108,9 @@ > status = "okay"; > > axp209: pmic@34 { > - compatible = "x-powers,axp209"; > reg = <0x34>; > interrupt-parent = <&nmi_intc>; > interrupts = <0 IRQ_TYPE_LEVEL_LOW>; > - > - interrupt-controller; > - #interrupt-cells = <1>; > - > - acin-supply = <®_axp_ipsout>; > - vin2-supply = <®_axp_ipsout>; > - vin3-supply = <®_axp_ipsout>; > - ldo24in-supply = <®_axp_ipsout>; > - ldo3in-supply = <®_axp_ipsout>; > - > - regulators { > - vdd_rtc: ldo1 { > - regulator-min-microvolt = <1300000>; > - regulator-max-microvolt = <1300000>; > - regulator-always-on; > - }; > - > - avcc: ldo2 { > - regulator-min-microvolt = <1800000>; > - regulator-max-microvolt = <3300000>; > - regulator-always-on; > - }; > - > - vcc_csi0: ldo3 { > - regulator-min-microvolt = <700000>; > - regulator-max-microvolt = <3500000>; > - regulator-always-on; > - }; > - > - vcc_csi1: ldo4 { > - regulator-min-microvolt = <1250000>; > - regulator-max-microvolt = <3300000>; > - regulator-always-on; > - }; > - > - vdd_cpu: dcdc2 { > - regulator-min-microvolt = <700000>; > - regulator-max-microvolt = <2275000>; > - regulator-always-on; > - }; > - > - vdd_int: dcdc3 { > - regulator-min-microvolt = <700000>; > - regulator-max-microvolt = <3500000>; > - regulator-always-on; > - }; > - }; > }; > }; > > @@ -196,6 +144,10 @@ > status = "okay"; > }; > > +&otg_sram { > + status = "okay"; > +}; > + > &pio { > ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { > allwinner,pins = "PC3"; > @@ -210,6 +162,27 @@ > allwinner,drive = <SUN4I_PINCTRL_20_MA>; > allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; > }; > + > + usb0_id_detect_pin: usb0_id_detect_pin@0 { > + allwinner,pins = "PH4"; > + allwinner,function = "gpio_in"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; > + }; > + > + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { > + allwinner,pins = "PH5"; > + allwinner,function = "gpio_in"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; > + }; > + > + usb0_vbus_pin_lime2: usb0_vbus_pin@0 { > + allwinner,pins = "PC17"; > + allwinner,function = "gpio_out"; > + allwinner,drive = <SUN4I_PINCTRL_10_MA>; > + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; > + }; > }; > > ®_ahci_5v { > @@ -218,6 +191,42 @@ > status = "okay"; > }; > > +#include "axp209.dtsi" > + > +®_dcdc2 { > + regulator-always-on; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1450000>; > + regulator-name = "vdd-cpu"; > +}; > + > +®_dcdc3 { > + regulator-always-on; > + regulator-min-microvolt = <1000000>; > + regulator-max-microvolt = <1400000>; > + regulator-name = "vdd-int-dll"; > +}; > + > +®_ldo1 { > + regulator-always-on; > + regulator-min-microvolt = <1300000>; > + regulator-max-microvolt = <1300000>; > + regulator-name = "vdd-rtc"; > +}; > + > +®_ldo2 { > + regulator-always-on; > + regulator-min-microvolt = <3000000>; > + regulator-max-microvolt = <3000000>; > + regulator-name = "avcc"; > +}; > + > +®_usb0_vbus { > + pinctrl-0 = <&usb0_vbus_pin_lime2>; > + gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>; > + status = "okay"; > +}; > + > ®_usb1_vbus { > status = "okay"; > }; > @@ -232,7 +241,17 @@ > status = "okay"; > }; > > +&usb_otg { > + dr_mode = "otg"; > + status = "okay"; > +}; > + > &usbphy { > + pinctrl-names = "default"; > + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; > + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ > + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ > + usb0_vbus-supply = <®_usb0_vbus>; > usb1_vbus-supply = <®_usb1_vbus>; > usb2_vbus-supply = <®_usb2_vbus>; > status = "okay"; > ^ permalink raw reply [flat|nested] 4+ messages in thread
* Re: [linux-sunxi] [PATCH] ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 2015-08-09 23:05 ` [linux-sunxi] " Iain Paton @ 2015-08-10 8:43 ` Olliver Schinagl 0 siblings, 0 replies; 4+ messages in thread From: Olliver Schinagl @ 2015-08-10 8:43 UTC (permalink / raw) To: Iain Paton Cc: Maxime Ripard, Olliver Schinagl, dev, Rob Herring, Pawel Moll, Mark Rutland, Ian Campbell, Kumar Gala, Russell King, devicetree, linux-arm-kernel, linux-kernel, Olliver Schinagl Yeah I just noticed as well that for some reason i've sent a merged patch :( I all ready fixed it locally this morning and will re-send the patches. I wonder what I did though .. Sorry again, Olliver On 10-08-15 01:05, Iain Paton wrote: > NAK. This does much more than enabling the otg port. > > Neither wholesale re-writing the regulator node or hooking up the > dcdc2 regulator to the operating points definition is required in order > to enable the otg port. > > At the very least you need to split your patches and describe them > properly rather than trying to get additional changes that are likely > to cause further discussion through unnoticed using a misleading > subject. > > Rgds, > Iain > > On 09/08/15 20:02, Olliver Schinagl wrote: >> From: Olliver Schinagl <o.schinagl@ultimaker.com> >> >> This patch enables the musb-otg USB controller on the Lime2. The Lime2 >> differs from the Lime1 series in pins used for usb0 power. >> >> Tested on a OlinuXino Lime2-4GB. >> >> Signed-off-by: Olliver Schinagl <oliver@schinagl.nl> >> --- >> arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts | 131 ++++++++++++++---------- >> 1 file changed, 75 insertions(+), 56 deletions(-) >> >> diff --git a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts >> index 22cd052..efd9ebb 100644 >> --- a/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts >> +++ b/arch/arm/boot/dts/sun7i-a20-olinuxino-lime2.dts >> @@ -71,14 +71,6 @@ >> default-state = "on"; >> }; >> }; >> - >> - reg_axp_ipsout: axp_ipsout { >> - compatible = "regulator-fixed"; >> - regulator-name = "axp-ipsout"; >> - regulator-min-microvolt = <5000000>; >> - regulator-max-microvolt = <5000000>; >> - regulator-always-on; >> - }; >> }; >> >> &ahci { >> @@ -86,6 +78,10 @@ >> status = "okay"; >> }; >> >> +&cpu0 { >> + cpu-supply = <®_dcdc2>; >> +}; >> + >> &ehci0 { >> status = "okay"; >> }; >> @@ -112,57 +108,9 @@ >> status = "okay"; >> >> axp209: pmic@34 { >> - compatible = "x-powers,axp209"; >> reg = <0x34>; >> interrupt-parent = <&nmi_intc>; >> interrupts = <0 IRQ_TYPE_LEVEL_LOW>; >> - >> - interrupt-controller; >> - #interrupt-cells = <1>; >> - >> - acin-supply = <®_axp_ipsout>; >> - vin2-supply = <®_axp_ipsout>; >> - vin3-supply = <®_axp_ipsout>; >> - ldo24in-supply = <®_axp_ipsout>; >> - ldo3in-supply = <®_axp_ipsout>; >> - >> - regulators { >> - vdd_rtc: ldo1 { >> - regulator-min-microvolt = <1300000>; >> - regulator-max-microvolt = <1300000>; >> - regulator-always-on; >> - }; >> - >> - avcc: ldo2 { >> - regulator-min-microvolt = <1800000>; >> - regulator-max-microvolt = <3300000>; >> - regulator-always-on; >> - }; >> - >> - vcc_csi0: ldo3 { >> - regulator-min-microvolt = <700000>; >> - regulator-max-microvolt = <3500000>; >> - regulator-always-on; >> - }; >> - >> - vcc_csi1: ldo4 { >> - regulator-min-microvolt = <1250000>; >> - regulator-max-microvolt = <3300000>; >> - regulator-always-on; >> - }; >> - >> - vdd_cpu: dcdc2 { >> - regulator-min-microvolt = <700000>; >> - regulator-max-microvolt = <2275000>; >> - regulator-always-on; >> - }; >> - >> - vdd_int: dcdc3 { >> - regulator-min-microvolt = <700000>; >> - regulator-max-microvolt = <3500000>; >> - regulator-always-on; >> - }; >> - }; >> }; >> }; >> >> @@ -196,6 +144,10 @@ >> status = "okay"; >> }; >> >> +&otg_sram { >> + status = "okay"; >> +}; >> + >> &pio { >> ahci_pwr_pin_olinuxinolime: ahci_pwr_pin@1 { >> allwinner,pins = "PC3"; >> @@ -210,6 +162,27 @@ >> allwinner,drive = <SUN4I_PINCTRL_20_MA>; >> allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> }; >> + >> + usb0_id_detect_pin: usb0_id_detect_pin@0 { >> + allwinner,pins = "PH4"; >> + allwinner,function = "gpio_in"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_PULL_UP>; >> + }; >> + >> + usb0_vbus_detect_pin: usb0_vbus_detect_pin@0 { >> + allwinner,pins = "PH5"; >> + allwinner,function = "gpio_in"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_PULL_DOWN>; >> + }; >> + >> + usb0_vbus_pin_lime2: usb0_vbus_pin@0 { >> + allwinner,pins = "PC17"; >> + allwinner,function = "gpio_out"; >> + allwinner,drive = <SUN4I_PINCTRL_10_MA>; >> + allwinner,pull = <SUN4I_PINCTRL_NO_PULL>; >> + }; >> }; >> >> ®_ahci_5v { >> @@ -218,6 +191,42 @@ >> status = "okay"; >> }; >> >> +#include "axp209.dtsi" >> + >> +®_dcdc2 { >> + regulator-always-on; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1450000>; >> + regulator-name = "vdd-cpu"; >> +}; >> + >> +®_dcdc3 { >> + regulator-always-on; >> + regulator-min-microvolt = <1000000>; >> + regulator-max-microvolt = <1400000>; >> + regulator-name = "vdd-int-dll"; >> +}; >> + >> +®_ldo1 { >> + regulator-always-on; >> + regulator-min-microvolt = <1300000>; >> + regulator-max-microvolt = <1300000>; >> + regulator-name = "vdd-rtc"; >> +}; >> + >> +®_ldo2 { >> + regulator-always-on; >> + regulator-min-microvolt = <3000000>; >> + regulator-max-microvolt = <3000000>; >> + regulator-name = "avcc"; >> +}; >> + >> +®_usb0_vbus { >> + pinctrl-0 = <&usb0_vbus_pin_lime2>; >> + gpio = <&pio 2 17 GPIO_ACTIVE_HIGH>; >> + status = "okay"; >> +}; >> + >> ®_usb1_vbus { >> status = "okay"; >> }; >> @@ -232,7 +241,17 @@ >> status = "okay"; >> }; >> >> +&usb_otg { >> + dr_mode = "otg"; >> + status = "okay"; >> +}; >> + >> &usbphy { >> + pinctrl-names = "default"; >> + pinctrl-0 = <&usb0_id_detect_pin>, <&usb0_vbus_detect_pin>; >> + usb0_id_det-gpio = <&pio 7 4 GPIO_ACTIVE_HIGH>; /* PH4 */ >> + usb0_vbus_det-gpio = <&pio 7 5 GPIO_ACTIVE_HIGH>; /* PH5 */ >> + usb0_vbus-supply = <®_usb0_vbus>; >> usb1_vbus-supply = <®_usb1_vbus>; >> usb2_vbus-supply = <®_usb2_vbus>; >> status = "okay"; >> ^ permalink raw reply [flat|nested] 4+ messages in thread
end of thread, other threads:[~2015-08-10 8:43 UTC | newest] Thread overview: 4+ messages (download: mbox.gz / follow: Atom feed) -- links below jump to the message on this page -- 2015-08-09 19:02 [PATCH] ARM: dts: sunxi: Use the axp209 driver on the olimex lime2 Olliver Schinagl 2015-08-09 19:02 ` [PATCH] ARM: dts: sunxi: enable otg port on the sun7i-a20-olinuxino-lime2 Olliver Schinagl 2015-08-09 23:05 ` [linux-sunxi] " Iain Paton 2015-08-10 8:43 ` Olliver Schinagl
This is a public inbox, see mirroring instructions for how to clone and mirror all data and code used for this inbox
Powered by JetHome