[PATCH 0/3] add support for EXAR XR20M1172 UART

[PATCH 0/3] add support for EXAR XR20M1172 UART

[Konstantin]

From: Konstantin Pugin <ria.freelander@gmail.com>

EXAR XR20M1172 UART is mostly SC16IS762-compatible, but
it has additional register which can change UART multiplier
to 4x and 8x, similar to UPF_MAGIC_MULTIPLIER does. So, I used this
flag to guard access to its specific DLD register. It seems than
other EXAR SPI UART modules also have this register, but I tested
only XR20M1172.

Konstantin (3):
  serial: sc16is7xx: announce support of SER_RS485_RTS_ON_SEND
  serial: sc16is7xx: Add bindings documentation for EXAR XR20M1172 UART
  serial: sc16is7xx: add support for EXAR XR20M1172 UART

 .../bindings/serial/nxp,sc16is7xx.yaml        |  1 +
 drivers/tty/serial/sc16is7xx.c                | 56 +++++++++++++++++--
 2 files changed, 53 insertions(+), 4 deletions(-)

-- 
2.34.1

[PATCH 1/3] serial: sc16is7xx: announce support of SER_RS485_RTS_ON_SEND

[Konstantin]

From: Konstantin <ria.freelander@gmail.com>

Hardware supports both modes, but after
commit 4afeced55baa ("serial: core: fix sanitizing check for RTS settings")
we always end up with SER_RS485_RTS_AFTER_SEND and always write in
register SC16IS7XX_EFCR_RTS_INVERT_BIT,
which breaks some hardware using these chips,

Fixes: 267913ecf737 ("serial: sc16is7xx: Fill in rs485_supported")
Signed-off-by: Konstantin Pugin <ria.freelander@gmail.com>
---
 drivers/tty/serial/sc16is7xx.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index 929206a9a6e1..a300eebf1401 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -1458,7 +1458,7 @@ static int sc16is7xx_setup_mctrl_ports(struct sc16is7xx_port *s,
 }
 
 static const struct serial_rs485 sc16is7xx_rs485_supported = {
-	.flags = SER_RS485_ENABLED | SER_RS485_RTS_AFTER_SEND,
+	.flags = SER_RS485_ENABLED | SER_RS485_RTS_ON_SEND | SER_RS485_RTS_AFTER_SEND,
 	.delay_rts_before_send = 1,
 	.delay_rts_after_send = 1,	/* Not supported but keep returning -EINVAL */
 };
-- 
2.34.1

[PATCH 2/3] serial: sc16is7xx: Add bindings documentation for EXAR XR20M1172 UART

[Konstantin]

From: Konstantin <ria.freelander@gmail.com>

This patch adds the devicetree documentation for the XR20M1172 UART.

Signed-off-by: Konstantin Pugin <ria.freelander@gmail.com>
---
 Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml
index 5dec15b7e7c3..68fe7b11961c 100644
--- a/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml
+++ b/Documentation/devicetree/bindings/serial/nxp,sc16is7xx.yaml
@@ -18,6 +18,7 @@ properties:
       - nxp,sc16is752
       - nxp,sc16is760
       - nxp,sc16is762
+      - exar,xr20m1172
 
   reg:
     maxItems: 1
-- 
2.34.1

Re: [PATCH 2/3] serial: sc16is7xx: Add bindings documentation for EXAR XR20M1172 UART

[Vladimir Zapolskiy]

Hi Konstantin,

On 4/18/24 16:25, Konstantin wrote:
> From: Konstantin <ria.freelander@gmail.com>

please use a full name, which points to the author of the change, thank you!

> This patch adds the devicetree documentation for the XR20M1172 UART.
> 
> Signed-off-by: Konstantin Pugin <ria.freelander@gmail.com>

Other than that the change is good from my point of view.

Please make the requested update, add my tag below and resubmit v2 of the change.

Reviewed-by: Vladimir Zapolskiy <vz@mleia.com>

--
Best wishes,
Vladimir

[PATCH 3/3] serial: sc16is7xx: add support for EXAR XR20M1172 UART

[Konstantin]

From: Konstantin <ria.freelander@gmail.com>

Its register set is mostly compatible with SC16IS762, but
it has a support for additional division rates of UART
with special DLD register. So, add handling this register
via UPF_MAGIC_MULTIPLIER port flag.

Signed-off-by: Konstantin Pugin <ria.freelander@gmail.com>
---
 drivers/tty/serial/sc16is7xx.c | 54 ++++++++++++++++++++++++++++++++--
 1 file changed, 51 insertions(+), 3 deletions(-)

diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
index a300eebf1401..7fc1c19b3891 100644
--- a/drivers/tty/serial/sc16is7xx.c
+++ b/drivers/tty/serial/sc16is7xx.c
@@ -65,6 +65,7 @@
 /* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */
 #define SC16IS7XX_DLL_REG		(0x00) /* Divisor Latch Low */
 #define SC16IS7XX_DLH_REG		(0x01) /* Divisor Latch High */
+#define SC16IS7XX_DLD_REG		(0x02) /* Divisor Latch Mode (only on EXAR chips) */
 
 /* Enhanced Register set: Only if (LCR == 0xBF) */
 #define SC16IS7XX_EFR_REG		(0x02) /* Enhanced Features */
@@ -218,6 +219,20 @@
 #define SC16IS7XX_TCR_RX_HALT(words)	((((words) / 4) & 0x0f) << 0)
 #define SC16IS7XX_TCR_RX_RESUME(words)	((((words) / 4) & 0x0f) << 4)
 
+/* Divisor Latch Mode bits (EXAR extension)
+ *
+ * EXAR hardware is mostly compatible with SC16IS7XX, but supports additional feature:
+ * 4x and 8x divisor, instead of default 16x. It has a special register to program it.
+ * Bits 0 to 3 is fractional divisor, it used to set value of last 16 bits of
+ * uartclk * (16 / divisor) / baud, in case of default it will be uartclk / baud.
+ * Bits 4 and 5 used as switches, and should not be set to 1 simultaneously.
+ */
+
+#define SC16IS7XX_DLD_16X		0
+#define SC16IS7XX_DLD_DIV(m)	((m) & 0xf)
+#define SC16IS7XX_DLD_8X		BIT(4)
+#define SC16IS7XX_DLD_4X		BIT(5)
+
 /*
  * TLR register bits
  * If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the
@@ -310,6 +325,7 @@ struct sc16is7xx_devtype {
 	char	name[10];
 	int	nr_gpio;
 	int	nr_uart;
+	bool has_dld;
 };
 
 #define SC16IS7XX_RECONF_MD		(1 << 0)
@@ -522,6 +538,13 @@ static const struct sc16is7xx_devtype sc16is762_devtype = {
 	.nr_uart	= 2,
 };
 
+static const struct sc16is7xx_devtype xr20m1172_devtype = {
+	.name		= "XR20M1172",
+	.nr_gpio	= 8,
+	.nr_uart	= 2,
+	.has_dld	= true,
+};
+
 static bool sc16is7xx_regmap_volatile(struct device *dev, unsigned int reg)
 {
 	switch (reg) {
@@ -559,13 +582,29 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
 	struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
 	u8 lcr;
 	u8 prescaler = 0;
-	unsigned long clk = port->uartclk, div = clk / 16 / baud;
+	u8 divisor = 16;
+	u8 dld_mode = SC16IS7XX_DLD_16X;
+	bool has_dld = !!(port->flags & UPF_MAGIC_MULTIPLIER);
+	unsigned long clk = port->uartclk, div, div16;
+
+	if (has_dld)
+		while (DIV_ROUND_CLOSEST(port->uartclk, baud) < divisor)
+			divisor /= 2;
+
+	div16 = clk * (16 / divisor) / baud;
+	div = div16 / 16; /* For divisor = 16, it is the same as clk / 16 / baud */
 
 	if (div >= BIT(16)) {
 		prescaler = SC16IS7XX_MCR_CLKSEL_BIT;
 		div /= 4;
 	}
 
+	/* Count additional divisor for EXAR devices */
+	if (divisor == 8)
+		dld_mode = SC16IS7XX_DLD_8X;
+	if (divisor == 4)
+		dld_mode = SC16IS7XX_DLD_4X;
+
 	/* Enable enhanced features */
 	sc16is7xx_efr_lock(port);
 	sc16is7xx_port_update(port, SC16IS7XX_EFR_REG,
@@ -586,12 +625,14 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
 	regcache_cache_bypass(one->regmap, true);
 	sc16is7xx_port_write(port, SC16IS7XX_DLH_REG, div / 256);
 	sc16is7xx_port_write(port, SC16IS7XX_DLL_REG, div % 256);
+	if (has_dld)
+		sc16is7xx_port_write(port, SC16IS7XX_DLD_REG, dld_mode | SC16IS7XX_DLD_DIV(div16));
 	regcache_cache_bypass(one->regmap, false);
 
 	/* Restore LCR and access to general register set */
 	sc16is7xx_port_write(port, SC16IS7XX_LCR_REG, lcr);
 
-	return DIV_ROUND_CLOSEST(clk / 16, div);
+	return DIV_ROUND_CLOSEST(clk / divisor, div);
 }
 
 static void sc16is7xx_handle_rx(struct uart_port *port, unsigned int rxlen,
@@ -1014,6 +1055,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
 	unsigned int lcr, flow = 0;
 	int baud;
 	unsigned long flags;
+	bool has_dld = !!(port->flags & UPF_MAGIC_MULTIPLIER);
 
 	kthread_cancel_delayed_work_sync(&one->ms_work);
 
@@ -1093,7 +1135,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
 	/* Get baud rate generator configuration */
 	baud = uart_get_baud_rate(port, termios, old,
 				  port->uartclk / 16 / 4 / 0xffff,
-				  port->uartclk / 16);
+				  port->uartclk / (has_dld ? 4 : 16));
 
 	/* Setup baudrate generator */
 	baud = sc16is7xx_set_baud(port, baud);
@@ -1550,6 +1592,9 @@ static int sc16is7xx_probe(struct device *dev,
 		s->p[i].port.type	= PORT_SC16IS7XX;
 		s->p[i].port.fifosize	= SC16IS7XX_FIFO_SIZE;
 		s->p[i].port.flags	= UPF_FIXED_TYPE | UPF_LOW_LATENCY;
+		/* If we have DLD register, then set UPF_MAGIC_MULTIPLIER flag */
+		if (devtype->has_dld)
+			s->p[i].port.flags |= UPF_MAGIC_MULTIPLIER;
 		s->p[i].port.iobase	= i;
 		/*
 		 * Use all ones as membase to make sure uart_configure_port() in
@@ -1688,6 +1733,7 @@ static const struct of_device_id __maybe_unused sc16is7xx_dt_ids[] = {
 	{ .compatible = "nxp,sc16is752",	.data = &sc16is752_devtype, },
 	{ .compatible = "nxp,sc16is760",	.data = &sc16is760_devtype, },
 	{ .compatible = "nxp,sc16is762",	.data = &sc16is762_devtype, },
+	{ .compatible = "exar,xr20m1172",	.data = &xr20m1172_devtype, },
 	{ }
 };
 MODULE_DEVICE_TABLE(of, sc16is7xx_dt_ids);
@@ -1776,6 +1822,7 @@ static const struct spi_device_id sc16is7xx_spi_id_table[] = {
 	{ "sc16is752",	(kernel_ulong_t)&sc16is752_devtype, },
 	{ "sc16is760",	(kernel_ulong_t)&sc16is760_devtype, },
 	{ "sc16is762",	(kernel_ulong_t)&sc16is762_devtype, },
+	{ "xr20m1172",	(kernel_ulong_t)&xr20m1172_devtype, },
 	{ }
 };
 
@@ -1826,6 +1873,7 @@ static const struct i2c_device_id sc16is7xx_i2c_id_table[] = {
 	{ "sc16is752",	(kernel_ulong_t)&sc16is752_devtype, },
 	{ "sc16is760",	(kernel_ulong_t)&sc16is760_devtype, },
 	{ "sc16is762",	(kernel_ulong_t)&sc16is762_devtype, },
+	{ "xr20m1172",	(kernel_ulong_t)&xr20m1172_devtype, },
 	{ }
 };
 MODULE_DEVICE_TABLE(i2c, sc16is7xx_i2c_id_table);
-- 
2.34.1

Re: [PATCH 3/3] serial: sc16is7xx: add support for EXAR XR20M1172 UART

[Jiri Slaby]

On 18. 04. 24, 15:25, Konstantin wrote:
> From: Konstantin <ria.freelander@gmail.com>
> 
> Its register set is mostly compatible with SC16IS762, but
> it has a support for additional division rates of UART
> with special DLD register. So, add handling this register
> via UPF_MAGIC_MULTIPLIER port flag.
> 
> Signed-off-by: Konstantin Pugin <ria.freelander@gmail.com>
> ---
>   drivers/tty/serial/sc16is7xx.c | 54 ++++++++++++++++++++++++++++++++--
>   1 file changed, 51 insertions(+), 3 deletions(-)
> 
> diff --git a/drivers/tty/serial/sc16is7xx.c b/drivers/tty/serial/sc16is7xx.c
> index a300eebf1401..7fc1c19b3891 100644
> --- a/drivers/tty/serial/sc16is7xx.c
> +++ b/drivers/tty/serial/sc16is7xx.c
> @@ -65,6 +65,7 @@
>   /* Special Register set: Only if ((LCR[7] == 1) && (LCR != 0xBF)) */
>   #define SC16IS7XX_DLL_REG		(0x00) /* Divisor Latch Low */
>   #define SC16IS7XX_DLH_REG		(0x01) /* Divisor Latch High */
> +#define SC16IS7XX_DLD_REG		(0x02) /* Divisor Latch Mode (only on EXAR chips) */
>   
>   /* Enhanced Register set: Only if (LCR == 0xBF) */
>   #define SC16IS7XX_EFR_REG		(0x02) /* Enhanced Features */
> @@ -218,6 +219,20 @@
>   #define SC16IS7XX_TCR_RX_HALT(words)	((((words) / 4) & 0x0f) << 0)
>   #define SC16IS7XX_TCR_RX_RESUME(words)	((((words) / 4) & 0x0f) << 4)
>   
> +/* Divisor Latch Mode bits (EXAR extension)
> + *
> + * EXAR hardware is mostly compatible with SC16IS7XX, but supports additional feature:
> + * 4x and 8x divisor, instead of default 16x. It has a special register to program it.
> + * Bits 0 to 3 is fractional divisor, it used to set value of last 16 bits of
> + * uartclk * (16 / divisor) / baud, in case of default it will be uartclk / baud.
> + * Bits 4 and 5 used as switches, and should not be set to 1 simultaneously.
> + */
> +
> +#define SC16IS7XX_DLD_16X		0
> +#define SC16IS7XX_DLD_DIV(m)	((m) & 0xf)

Why not to use GENMASK() here and FIELD_PREP() in the code?

> +#define SC16IS7XX_DLD_8X		BIT(4)
> +#define SC16IS7XX_DLD_4X		BIT(5)
> +
>   /*
>    * TLR register bits
>    * If TLR[3:0] or TLR[7:4] are logical 0, the selectable trigger levels via the
...
> @@ -559,13 +582,29 @@ static int sc16is7xx_set_baud(struct uart_port *port, int baud)
>   	struct sc16is7xx_one *one = to_sc16is7xx_one(port, port);
>   	u8 lcr;
>   	u8 prescaler = 0;
> -	unsigned long clk = port->uartclk, div = clk / 16 / baud;
> +	u8 divisor = 16;
> +	u8 dld_mode = SC16IS7XX_DLD_16X;
> +	bool has_dld = !!(port->flags & UPF_MAGIC_MULTIPLIER);

No need for !!.

> +	unsigned long clk = port->uartclk, div, div16;

All these locals would deserve better ordering.

...
> @@ -1014,6 +1055,7 @@ static void sc16is7xx_set_termios(struct uart_port *port,
>   	unsigned int lcr, flow = 0;
>   	int baud;
>   	unsigned long flags;
> +	bool has_dld = !!(port->flags & UPF_MAGIC_MULTIPLIER);

Ditto.

>   
>   	kthread_cancel_delayed_work_sync(&one->ms_work);
>   
thanks,
-- 
js
suse labs