From: "Matt Fleming" <mattjfleming@googlemail.com>
To: linux-kernel@vger.kernel.org, drzeus-mmc@drzeus.cx,
dbrownell@users.sourceforge.net
Subject: [RFC][PATCH] MMC: Use write timeout value as read from CSR
Date: Mon, 1 Sep 2008 16:12:03 +0100 [thread overview]
Message-ID: <5ff4a1e50809010812i32168136qea538ba177b81446@mail.gmail.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 3972 bytes --]
Currently, the MMC/SD over SPI code has a hard-coded timeout value of
250ms on writes. This is correct for SD cards and is specified in the
spec, but it is not correct for MMC cards. For MMC cards the values
that is read from the CSR should be used.
There is already code to ensure that the write timeout value for SD
cards does not exceed 250ms, this patch only affects the MMC case.
diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c
index 7503b81..2818837 100644
--- a/drivers/mmc/host/mmc_spi.c
+++ b/drivers/mmc/host/mmc_spi.c
@@ -34,6 +34,7 @@
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h> /* for R1_SPI_* bit values */
+#include <linux/mmc/card.h>
#include <linux/spi/spi.h>
#include <linux/spi/mmc_spi.h>
@@ -96,7 +97,6 @@
* shorter timeouts ... but why bother?
*/
#define readblock_timeout ktime_set(0, 100 * 1000 * 1000)
-#define writeblock_timeout ktime_set(0, 250 * 1000 * 1000)
#define r1b_timeout ktime_set(3, 0)
@@ -225,6 +225,20 @@ static int mmc_spi_readtoken(struct mmc_spi_host *host)
return mmc_spi_skip(host, readblock_timeout, 1, 0xff);
}
+/*
+ * Return the write timeout value (in nanoseconds) for this card.
+ */
+static inline unsigned int
+mmc_get_write_timeout(struct mmc_spi_host *host, struct mmc_data *data)
+{
+ unsigned int timeout_ns;
+
+ timeout_ns = data->timeout_ns;
+ timeout_ns += data->timeout_clks * 1000 * 1000 /
+ (host->mmc->card->host->ios.clock);
+
+ return timeout_ns;
+}
/*
* Note that for SPI, cmd->resp[0] is not the same data as "native" protocol
@@ -605,11 +619,13 @@ mmc_spi_setup_data_message(
* Return negative errno, else success.
*/
static int
-mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t)
+mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t,
+ struct mmc_data *data)
{
struct spi_device *spi = host->spi;
int status, i;
struct scratch *scratch = host->data;
+ unsigned int timeout_ns;
if (host->mmc->use_spi_crc)
scratch->crc_val = cpu_to_be16(
@@ -673,7 +689,11 @@ mmc_spi_writeblock(struct mmc_spi_host *host,
struct spi_transfer *t)
if (scratch->status[i] != 0)
return 0;
}
- return mmc_spi_wait_unbusy(host, writeblock_timeout);
+
+ timeout_ns = mmc_get_write_timeout(host, data);
+
+ return mmc_spi_wait_unbusy(host,
+ ktime_add_ns(ktime_set(0, 0), timeout_ns));
}
/*
@@ -832,7 +852,7 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct
mmc_command *cmd,
t->len);
if (direction == DMA_TO_DEVICE)
- status = mmc_spi_writeblock(host, t);
+ status = mmc_spi_writeblock(host, t, data);
else
status = mmc_spi_readblock(host, t);
if (status < 0)
@@ -872,6 +892,7 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct
mmc_command *cmd,
struct scratch *scratch = host->data;
int tmp;
const unsigned statlen = sizeof(scratch->status);
+ unsigned int timeout_ns;
dev_dbg(&spi->dev, " mmc_spi: STOP_TRAN\n");
@@ -917,7 +938,9 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct
mmc_command *cmd,
if (scratch->status[tmp] != 0)
return;
}
- tmp = mmc_spi_wait_unbusy(host, writeblock_timeout);
+ timeout_ns = mmc_get_write_timeout(host, data);
+ tmp = mmc_spi_wait_unbusy(host,
+ ktime_add_ns(ktime_set(0, 0), timeout_ns));
if (tmp < 0 && !data->error)
data->error = tmp;
}
[-- Warning: decoded text below may be mangled, UTF-8 assumed --]
[-- Attachment #2: mmc-spi-use-timeout-from-card.patch --]
[-- Type: text/x-diff; name=mmc-spi-use-timeout-from-card.patch, Size: 2955 bytes --]
diff --git a/drivers/mmc/host/mmc_spi.c b/drivers/mmc/host/mmc_spi.c
index 7503b81..2818837 100644
--- a/drivers/mmc/host/mmc_spi.c
+++ b/drivers/mmc/host/mmc_spi.c
@@ -34,6 +34,7 @@
#include <linux/mmc/host.h>
#include <linux/mmc/mmc.h> /* for R1_SPI_* bit values */
+#include <linux/mmc/card.h>
#include <linux/spi/spi.h>
#include <linux/spi/mmc_spi.h>
@@ -96,7 +97,6 @@
* shorter timeouts ... but why bother?
*/
#define readblock_timeout ktime_set(0, 100 * 1000 * 1000)
-#define writeblock_timeout ktime_set(0, 250 * 1000 * 1000)
#define r1b_timeout ktime_set(3, 0)
@@ -225,6 +225,20 @@ static int mmc_spi_readtoken(struct mmc_spi_host *host)
return mmc_spi_skip(host, readblock_timeout, 1, 0xff);
}
+/*
+ * Return the write timeout value (in nanoseconds) for this card.
+ */
+static inline unsigned int
+mmc_get_write_timeout(struct mmc_spi_host *host, struct mmc_data *data)
+{
+ unsigned int timeout_ns;
+
+ timeout_ns = data->timeout_ns;
+ timeout_ns += data->timeout_clks * 1000 * 1000 /
+ (host->mmc->card->host->ios.clock);
+
+ return timeout_ns;
+}
/*
* Note that for SPI, cmd->resp[0] is not the same data as "native" protocol
@@ -605,11 +619,13 @@ mmc_spi_setup_data_message(
* Return negative errno, else success.
*/
static int
-mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t)
+mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t,
+ struct mmc_data *data)
{
struct spi_device *spi = host->spi;
int status, i;
struct scratch *scratch = host->data;
+ unsigned int timeout_ns;
if (host->mmc->use_spi_crc)
scratch->crc_val = cpu_to_be16(
@@ -673,7 +689,11 @@ mmc_spi_writeblock(struct mmc_spi_host *host, struct spi_transfer *t)
if (scratch->status[i] != 0)
return 0;
}
- return mmc_spi_wait_unbusy(host, writeblock_timeout);
+
+ timeout_ns = mmc_get_write_timeout(host, data);
+
+ return mmc_spi_wait_unbusy(host,
+ ktime_add_ns(ktime_set(0, 0), timeout_ns));
}
/*
@@ -832,7 +852,7 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct mmc_command *cmd,
t->len);
if (direction == DMA_TO_DEVICE)
- status = mmc_spi_writeblock(host, t);
+ status = mmc_spi_writeblock(host, t, data);
else
status = mmc_spi_readblock(host, t);
if (status < 0)
@@ -872,6 +892,7 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct mmc_command *cmd,
struct scratch *scratch = host->data;
int tmp;
const unsigned statlen = sizeof(scratch->status);
+ unsigned int timeout_ns;
dev_dbg(&spi->dev, " mmc_spi: STOP_TRAN\n");
@@ -917,7 +938,9 @@ mmc_spi_data_do(struct mmc_spi_host *host, struct mmc_command *cmd,
if (scratch->status[tmp] != 0)
return;
}
- tmp = mmc_spi_wait_unbusy(host, writeblock_timeout);
+ timeout_ns = mmc_get_write_timeout(host, data);
+ tmp = mmc_spi_wait_unbusy(host,
+ ktime_add_ns(ktime_set(0, 0), timeout_ns));
if (tmp < 0 && !data->error)
data->error = tmp;
}
next reply other threads:[~2008-09-01 15:12 UTC|newest]
Thread overview: 16+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-09-01 15:12 Matt Fleming [this message]
2008-09-07 10:38 ` Pierre Ossman
2008-09-08 13:28 ` Matt Fleming
2008-09-08 19:18 ` David Brownell
2008-09-09 7:22 ` Pierre Ossman
2008-09-09 7:34 ` Matt Fleming
2008-09-09 7:44 ` Pierre Ossman
2008-09-09 7:59 ` Matt Fleming
2008-09-09 8:55 ` Pierre Ossman
2008-09-09 9:07 ` Matt Fleming
2008-09-09 9:42 ` Matt Fleming
2008-09-14 13:48 ` Pierre Ossman
[not found] ` <5ff4a1e50809150103v1e250e0x4192e2fe901750a6@mail.gmail.com>
[not found] ` <20080915103821.2b618bba@mjolnir.drzeus.cx>
2008-09-15 9:24 ` Matt Fleming
2008-09-20 11:06 ` Pierre Ossman
2008-09-24 11:16 ` Matt Fleming
2008-10-02 8:26 ` Pierre Ossman
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=5ff4a1e50809010812i32168136qea538ba177b81446@mail.gmail.com \
--to=mattjfleming@googlemail.com \
--cc=dbrownell@users.sourceforge.net \
--cc=drzeus-mmc@drzeus.cx \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®