Re: [PATCH V2 2/4] arm64: dts: qcom: sm8750: Add SDC2 nodes for sm8750 soc

[Sarthak Garg <sarthak.garg@oss.qualcomm.com>]

On 10/23/2025 5:44 PM, Abel Vesa wrote:
> On 25-10-23 16:59:22, Sarthak Garg wrote:
>> Add SD Card host controller for sm8750 soc.
>>
>> Signed-off-by: Sarthak Garg <sarthak.garg@oss.qualcomm.com>
>> ---
>>   arch/arm64/boot/dts/qcom/sm8750.dtsi | 68 ++++++++++++++++++++++++++++
>>   1 file changed, 68 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/sm8750.dtsi b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>> index a82d9867c7cb..1070dc5ea196 100644
>> --- a/arch/arm64/boot/dts/qcom/sm8750.dtsi
>> +++ b/arch/arm64/boot/dts/qcom/sm8750.dtsi
>> @@ -2060,6 +2060,60 @@ ice: crypto@1d88000 {
>>   			clocks = <&gcc GCC_UFS_PHY_ICE_CORE_CLK>;
>>   		};
>>   
>> +		sdhc_2: mmc@8804000 {
>> +			compatible = "qcom,sm8750-sdhci", "qcom,sdhci-msm-v5";
>> +			reg = <0 0x08804000 0 0x1000>;
>> +
>> +			interrupts = <GIC_SPI 207 IRQ_TYPE_LEVEL_HIGH>,
>> +				     <GIC_SPI 223 IRQ_TYPE_LEVEL_HIGH>;
>> +			interrupt-names = "hc_irq",
>> +					  "pwr_irq";
>> +
>> +			clocks = <&gcc GCC_SDCC2_AHB_CLK>,
>> +				 <&gcc GCC_SDCC2_APPS_CLK>,
>> +				 <&rpmhcc RPMH_CXO_CLK>;
>> +			clock-names = "iface",
>> +				      "core",
>> +				      "xo";
>> +
>> +			interconnects = <&aggre2_noc MASTER_SDCC_2 QCOM_ICC_TAG_ALWAYS
>> +					&mc_virt SLAVE_EBI1 QCOM_ICC_TAG_ALWAYS>,
>> +					<&gem_noc MASTER_APPSS_PROC QCOM_ICC_TAG_ACTIVE_ONLY
>> +					&config_noc SLAVE_SDCC_2 QCOM_ICC_TAG_ACTIVE_ONLY>;
>> +			interconnect-names = "sdhc-ddr",
>> +					     "cpu-sdhc";
>> +
>> +			power-domains = <&rpmhpd RPMHPD_CX>;
>> +			operating-points-v2 = <&sdhc2_opp_table>;
>> +
>> +			qcom,dll-config = <0x0007442c>;
>> +			qcom,ddr-config = <0x80040868>;
>> +
>> +			iommus = <&apps_smmu 0x540 0x0>;
>> +			dma-coherent;
>> +
>> +			bus-width = <4>;
>> +			max-sd-hs-hz = <37500000>;
>> +
>> +			resets = <&gcc GCC_SDCC2_BCR>;
>> +
>> +			status = "disabled";
>> +
>> +			sdhc2_opp_table: opp-table {
>> +				compatible = "operating-points-v2";
>> +
>> +				opp-100000000 {
>> +					opp-hz = /bits/ 64 <100000000>;
>> +					required-opps = <&rpmhpd_opp_low_svs>;
>> +				};
>> +
>> +				opp-202000000 {
>> +					opp-hz = /bits/ 64 <202000000>;
>> +					required-opps = <&rpmhpd_opp_svs_l1>;
>> +				};
>> +			};
>> +		};
>> +
>>   		cryptobam: dma-controller@1dc4000 {
>>   			compatible = "qcom,bam-v1.7.4", "qcom,bam-v1.7.0";
>>   			reg = <0x0 0x01dc4000 0x0 0x28000>;
>> @@ -3121,6 +3175,13 @@ data-pins {
>>   					drive-strength = <2>;
>>   					bias-pull-up;
>>   				};
>> +
>> +				card-detect-pins {
>> +					pins = "gpio55";
>> +					function = "gpio";
>> +					drive-strength = <2>;
>> +					bias-pull-up;
>> +				};
> These are board specific, so move them to the board dts.


Sure will update in V3.


>>   			};
>>   
>>   			sdc2_default: sdc2-default-state {
>> @@ -3141,6 +3202,13 @@ data-pins {
>>   					drive-strength = <10>;
>>   					bias-pull-up;
>>   				};
>> +
>> +				card-detect-pins {
>> +					pins = "gpio55";
>> +					function = "gpio";
>> +					drive-strength = <2>;
>> +					bias-pull-up;
>> +				};
> Ditto.


Sure will update in V3.

Regards,
Sarthak


>>   			};
>>   		};
>>   
>> -- 
>> 2.34.1
>>