[PATCH 0/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[PATCH 0/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Leonardo Costa]

From: Leonardo Costa <leonardo.costa@toradex.com>

This patch adds the device tree overlay for the Toradex Capacitive Touch
Display 10.1" LVDS V2 through the DSI to LVDS bridge on the Aquila
Development Carrier board with the Aquila AM69 SoM.

This change depends on two other patch series, and should be applied after
them: 

- https://lore.kernel.org/linux-arm-kernel/20260623195741.495734-1-leoreis.costa@gmail.com/T/#t

  Adds the Toradex Capacitive Touch Display 10.1" LVDS V2 overlays for the
  Verdin AM62. This series is required because it adds the panel bindings for
  the display. It is currently in linux-next.

- https://lore.kernel.org/all/20260602115123.1324474-9-ivitro@gmail.com/

    Adds the other device tree overlays for the Aquila AM69. It is currently in
    linux-next. This is required for the changes to apply cleanly.

Leonardo Costa (1):
  arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with
    the 10.1" V2 display

 arch/arm64/boot/dts/ti/Makefile               |   5 +
 ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
 2 files changed, 158 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso

[PATCH 1/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Leonardo Costa]

From: Leonardo Costa <leonardo.costa@toradex.com>

Add a device tree overlay for the Toradex DSI to LVDS Adapter with the
Toradex Capacitive Touch Display 10.1" LVDS V2. The adapter connects to the
Aquila DSI_1 interface. It is based on the Texas Instruments SN65DSI84
DSI-to-LVDS bridge and drives an Opto Logic SCX1001511GGC49 10.1" WXGA TFT
LCD LVDS panel. Touch input is provided by an ILITEK ILI251x capacitive
touch controller.

Link: https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
---
 arch/arm64/boot/dts/ti/Makefile               |   5 +
 ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
 2 files changed, 158 insertions(+)
 create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso

diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
index f4d109ef6798a..8a59fc597aede 100644
--- a/arch/arm64/boot/dts/ti/Makefile
+++ b/arch/arm64/boot/dts/ti/Makefile
@@ -218,6 +218,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev-dsi-to-hdmi.dtb
 dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dsi-to-hdmi.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dsi-to-lvds-panel-cap-touch-10inch.dtbo
+dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-panel-cap-touch-10inch-dsi.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-panel-cap-touch-7inch-dsi.dtbo
 dtb-$(CONFIG_ARCH_K3) += k3-am69-sk.dtb
@@ -374,6 +375,9 @@ k3-am69-aquila-dev-csi-ov5640-dtbs := \
 k3-am69-aquila-dev-dsi-to-lvds-panel-cap-touch-10inch-dtbs := \
 	k3-am69-aquila-dev.dtb \
 	k3-am69-aquila-dsi-to-lvds-panel-cap-touch-10inch.dtbo
+k3-am69-aquila-dev-dsi-to-lvds-v2-panel-cap-touch-10inch-dtbs := \
+	k3-am69-aquila-dev.dtb \
+	k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtbo
 k3-am69-sk-csi2-dual-imx219-dtbs := k3-am69-sk.dtb \
 	k3-j721e-sk-csi2-dual-imx219.dtbo
 k3-am69-sk-pcie0-ep-dtbs := k3-am69-sk.dtb \
@@ -471,6 +475,7 @@ dtb- += k3-am625-beagleplay-csi2-ov5640.dtb \
 	k3-am69-aquila-dev-csi-ov5640-24mhz.dtb \
 	k3-am69-aquila-dev-csi-ov5640.dtb \
 	k3-am69-aquila-dev-dsi-to-lvds-panel-cap-touch-10inch.dtb \
+	k3-am69-aquila-dev-dsi-to-lvds-v2-panel-cap-touch-10inch.dtb \
 	k3-am69-sk-csi2-dual-imx219.dtb \
 	k3-am69-sk-pcie0-ep.dtb \
 	k3-j7200-evm-pcie1-ep.dtb \
diff --git a/arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso b/arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
new file mode 100644
index 0000000000000..834f23e75cbc3
--- /dev/null
+++ b/arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
@@ -0,0 +1,153 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (c) Toradex
+ *
+ * Toradex DSI to LVDS Adapter on Aquila DSI_1 with Capacitive Touch Display
+ * 10.1" V2 Used on Development Board (J44). DSI_1 is exposed via a Samtec
+ * LSS-130 connector.
+ *
+ * https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
+ * https://www.toradex.com/accessories/capacitive-touch-display-10.1-inch-lvds
+ * https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
+ * https://www.toradex.com/accessories/verdin-dsi-to-lvds-adapter
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/interrupt-controller/irq.h>
+
+&{/} {
+	backlight_pwm3: backlight-pwm3 {
+		compatible = "pwm-backlight";
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_19_dsi_1>;
+		brightness-levels = <0 45 63 88 119 158 203 255>;
+		default-brightness-level = <4>;
+		/* Aquila GPIO_19_DSI_1 (AQUILA B44) */
+		enable-gpios = <&main_gpio0 13 GPIO_ACTIVE_HIGH>;
+		/* Aquila PWM_3_DSI (AQUILA B46) */
+		pwms = <&main_ehrpwm5 0 6666667 0>;
+	};
+
+	panel-lvds-bridge {
+		compatible = "optologic,scx1001511ggc49", "panel-lvds";
+		backlight = <&backlight_pwm3>;
+		data-mapping = "vesa-24";
+		height-mm = <136>;
+		width-mm = <217>;
+
+		panel-timing {
+			clock-frequency = <70000000>;
+			hactive = <1280>;
+			hback-porch = <55>;
+			hfront-porch = <55>;
+			hsync-len = <45>;
+			vactive = <800>;
+			vback-porch = <5>;
+			vfront-porch = <5>;
+			vsync-len = <3>;
+			de-active = <1>;
+			hsync-active = <0>;
+			vsync-active = <0>;
+			pixelclk-active = <0>;
+		};
+
+		port {
+			panel_lvds_bridge_in: endpoint {
+				remote-endpoint = <&dsi_lvds_bridge_out>;
+			};
+		};
+	};
+};
+
+&dphy_tx0 {
+	status = "okay";
+};
+
+&dsi0 {
+	status = "okay";
+};
+
+&dsi0_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@0 {
+		reg = <0>;
+
+		dsi0_out: endpoint {
+			remote-endpoint = <&dsi_lvds_bridge_in>;
+		};
+	};
+
+	port@1 {
+		reg = <1>;
+
+		dsi0_in: endpoint {
+			remote-endpoint = <&dpi2_out>;
+		};
+	};
+};
+
+&dss_ports {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	port@2 {
+		reg = <2>;
+
+		dpi2_out: endpoint {
+			remote-endpoint = <&dsi0_in>;
+		};
+	};
+};
+
+&i2c_dsi_0 {
+	#address-cells = <1>;
+	#size-cells = <0>;
+
+	bridge@2c {
+		compatible = "ti,sn65dsi84";
+		reg = <0x2c>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_20_dsi_1>;
+		/* Aquila GPIO_20_DSI_1 (AQUILA B45) */
+		enable-gpios = <&main_gpio0 18 GPIO_ACTIVE_HIGH>;
+
+		ports {
+			#address-cells = <1>;
+			#size-cells = <0>;
+
+			port@0 {
+				reg = <0>;
+
+				dsi_lvds_bridge_in: endpoint {
+					remote-endpoint = <&dsi0_out>;
+					data-lanes = <1 2 3 4>;
+				};
+			};
+
+			port@2 {
+				reg = <2>;
+
+				dsi_lvds_bridge_out: endpoint {
+					remote-endpoint = <&panel_lvds_bridge_in>;
+				};
+			};
+		};
+	};
+
+	touchscreen@41 {
+		compatible = "ilitek,ili251x";
+		reg = <0x41>;
+		pinctrl-names = "default";
+		pinctrl-0 = <&pinctrl_gpio_17_dsi_1>, <&pinctrl_gpio_18_dsi_1>;
+		/* Aquila GPIO_17_DSI_1 (AQUILA B42) */
+		interrupt-parent = <&main_gpio0>;
+		interrupts = <12 IRQ_TYPE_EDGE_RISING>;
+		/* Aquila GPIO_18_DSI_1 (AQUILA B43) */
+		reset-gpios = <&main_gpio0 31 GPIO_ACTIVE_LOW>;
+	};
+};

Re: [PATCH 1/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Kumar, Udit]

Hi Leonardo

On 8/3/2026 11:04 PM, Leonardo Costa wrote:
> From: Leonardo Costa <leonardo.costa@toradex.com>
> 
> Add a device tree overlay for the Toradex DSI to LVDS Adapter with the
> Toradex Capacitive Touch Display 10.1" LVDS V2. The adapter connects to the
> Aquila DSI_1 interface. It is based on the Texas Instruments SN65DSI84
> DSI-to-LVDS bridge and drives an Opto Logic SCX1001511GGC49 10.1" WXGA TFT
> LCD LVDS panel. Touch input is provided by an ILITEK ILI251x capacitive
> touch controller.
> 
> Link: https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
> Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
> Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
> ---
>  arch/arm64/boot/dts/ti/Makefile               |   5 +
>  ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
>  2 files changed, 158 insertions(+)
>  create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
> 
> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> index f4d109ef6798a..8a59fc597aede 100644
> --- a/arch/arm64/boot/dts/ti/Makefile
> +++ b/arch/arm64/boot/dts/ti/Makefile
> @@ -218,6 +218,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
> [..]
> +
> +	panel-lvds-bridge {
> +		compatible = "optologic,scx1001511ggc49", "panel-lvds";

> +		backlight = <&backlight_pwm3>;
> +		data-mapping = "vesa-24";
> +		height-mm = <136>;
> +		width-mm = <217>;
> +
> +		panel-timing {
> +			clock-frequency = <70000000>;

Looking at
https://lore.kernel.org/linux-arm-kernel/20260623195741.495734-1-leoreis.costa@gmail.com/T/#mc4ed25e5253da6dc635fd3eddc317dac8f447f3e


you are using three different clock-freq 69500000, 64500000 and
70000000 here.
Could add some comment here, why freq is adjusted.


> +			hactive = <1280>;
> +			hback-porch = <55>;
> +			hfront-porch = <55>;
> +			hsync-len = <45>;
> +			vactive = <800>;
> +			vback-porch = <5>;
> +			vfront-porch = <5>;
> +			vsync-len = <3>;
> +			de-active = <1>;
> +			hsync-active = <0>;
> +			vsync-active = <0>;
> +			pixelclk-active = <0>;
> +		};
> +
> +		port {
> +			panel_lvds_bridge_in: endpoint {
> +				remote-endpoint = <&dsi_lvds_bridge_out>;
> +			};
> +		};
[..]

Re: [PATCH 1/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Leonardo Costa]

Hi Udit,

On Sun, Sep 06, 2026 at 10:49:52AM +0530, Kumar, Udit wrote:
> Hi Leonardo
> 
> On 8/3/2026 11:04 PM, Leonardo Costa wrote:
> > From: Leonardo Costa <leonardo.costa@toradex.com>
> > 
> > Add a device tree overlay for the Toradex DSI to LVDS Adapter with the
> > Toradex Capacitive Touch Display 10.1" LVDS V2. The adapter connects to the
> > Aquila DSI_1 interface. It is based on the Texas Instruments SN65DSI84
> > DSI-to-LVDS bridge and drives an Opto Logic SCX1001511GGC49 10.1" WXGA TFT
> > LCD LVDS panel. Touch input is provided by an ILITEK ILI251x capacitive
> > touch controller.
> > 
> > Link: https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
> > Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
> > Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
> > ---
> >  arch/arm64/boot/dts/ti/Makefile               |   5 +
> >  ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
> >  2 files changed, 158 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
> > 
> > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> > index f4d109ef6798a..8a59fc597aede 100644
> > --- a/arch/arm64/boot/dts/ti/Makefile
> > +++ b/arch/arm64/boot/dts/ti/Makefile
> > @@ -218,6 +218,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
> > [..]
> > +
> > +	panel-lvds-bridge {
> > +		compatible = "optologic,scx1001511ggc49", "panel-lvds";
> 
> > +		backlight = <&backlight_pwm3>;
> > +		data-mapping = "vesa-24";
> > +		height-mm = <136>;
> > +		width-mm = <217>;
> > +
> > +		panel-timing {
> > +			clock-frequency = <70000000>;
> 
> Looking at
> https://lore.kernel.org/linux-arm-kernel/20260623195741.495734-1-leoreis.costa@gmail.com/T/#mc4ed25e5253da6dc635fd3eddc317dac8f447f3e
> 
> 
> you are using three different clock-freq 69500000, 64500000 and
> 70000000 here.
> Could add some comment here, why freq is adjusted.

It's for the same reason as the 69500000 clock frequency in the Verdin
AM62 patch. In general the DSI to LVDS bridge requires longer horizontal
porch and sync values than the typical values for the display, and we
intend to use the values on this patch in the general case when the
bridge is used. The reason why the frequency here (70000000) is
different from the Verdin AM62 one (69500000) is because we found that
that 70000000, along with the other timing values, work more
consistently with the bridge across our modules, the ones on the Verdin
AM62 ended up being a first iteration.

I'll add a comment explaining the difference from the native LVDS values
in the v2 patch.

Kind regards,
Leonardo

Re: [PATCH 1/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Leonardo Costa]

On Tue, Sep 08, 2026 at 08:17:57AM -0300, Leonardo Costa wrote:
> Hi Udit,
> 
> On Sun, Sep 06, 2026 at 10:49:52AM +0530, Kumar, Udit wrote:
> > Hi Leonardo
> > 
> > On 8/3/2026 11:04 PM, Leonardo Costa wrote:
> > > From: Leonardo Costa <leonardo.costa@toradex.com>
> > > 
> > > Add a device tree overlay for the Toradex DSI to LVDS Adapter with the
> > > Toradex Capacitive Touch Display 10.1" LVDS V2. The adapter connects to the
> > > Aquila DSI_1 interface. It is based on the Texas Instruments SN65DSI84
> > > DSI-to-LVDS bridge and drives an Opto Logic SCX1001511GGC49 10.1" WXGA TFT
> > > LCD LVDS panel. Touch input is provided by an ILITEK ILI251x capacitive
> > > touch controller.
> > > 
> > > Link: https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
> > > Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
> > > Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
> > > ---
> > >  arch/arm64/boot/dts/ti/Makefile               |   5 +
> > >  ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
> > >  2 files changed, 158 insertions(+)
> > >  create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
> > > 
> > > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> > > index f4d109ef6798a..8a59fc597aede 100644
> > > --- a/arch/arm64/boot/dts/ti/Makefile
> > > +++ b/arch/arm64/boot/dts/ti/Makefile
> > > @@ -218,6 +218,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
> > > [..]
> > > +
> > > +	panel-lvds-bridge {
> > > +		compatible = "optologic,scx1001511ggc49", "panel-lvds";
> > 
> > > +		backlight = <&backlight_pwm3>;
> > > +		data-mapping = "vesa-24";
> > > +		height-mm = <136>;
> > > +		width-mm = <217>;
> > > +
> > > +		panel-timing {
> > > +			clock-frequency = <70000000>;
> > 
> > Looking at
> > https://lore.kernel.org/linux-arm-kernel/20260623195741.495734-1-leoreis.costa@gmail.com/T/#mc4ed25e5253da6dc635fd3eddc317dac8f447f3e
> > 
> > 
> > you are using three different clock-freq 69500000, 64500000 and
> > 70000000 here.
> > Could add some comment here, why freq is adjusted.
> 
> It's for the same reason as the 69500000 clock frequency in the Verdin
> AM62 patch. In general the DSI to LVDS bridge requires longer horizontal
> porch and sync values than the typical values for the display, and we
> intend to use the values on this patch in the general case when the
> bridge is used. The reason why the frequency here (70000000) is
> different from the Verdin AM62 one (69500000) is because we found that
> that 70000000, along with the other timing values, work more
> consistently with the bridge across our modules, the ones on the Verdin
> AM62 ended up being a first iteration.
> 
> I'll add a comment explaining the difference from the native LVDS values
> in the v2 patch.

Correcting my last reply:

The 69500000 frequency and other timings were used on Verdin AM62 were
due to the DPI->DSI bridge used on the module, not only due to the DSI
to LVDS bridge that can be attached to the carrier boards. Ever since
that, we found that the DSI to LVDS bridge itself generally also needs
higher values to work consistently across our modules, compared to the
ones typical for the display.

Re: [PATCH 1/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Leonardo Costa]

Hi Udit,

On Sun, Sep 06, 2026 at 10:49:52AM +0530, Kumar, Udit wrote:
> Hi Leonardo
> 
> On 8/3/2026 11:04 PM, Leonardo Costa wrote:
> > From: Leonardo Costa <leonardo.costa@toradex.com>
> > 
> > Add a device tree overlay for the Toradex DSI to LVDS Adapter with the
> > Toradex Capacitive Touch Display 10.1" LVDS V2. The adapter connects to the
> > Aquila DSI_1 interface. It is based on the Texas Instruments SN65DSI84
> > DSI-to-LVDS bridge and drives an Opto Logic SCX1001511GGC49 10.1" WXGA TFT
> > LCD LVDS panel. Touch input is provided by an ILITEK ILI251x capacitive
> > touch controller.
> > 
> > Link: https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
> > Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
> > Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
> > ---
> >  arch/arm64/boot/dts/ti/Makefile               |   5 +
> >  ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
> >  2 files changed, 158 insertions(+)
> >  create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
> > 
> > diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
> > index f4d109ef6798a..8a59fc597aede 100644
> > --- a/arch/arm64/boot/dts/ti/Makefile
> > +++ b/arch/arm64/boot/dts/ti/Makefile
> > @@ -218,6 +218,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
> > [..]
> > +
> > +	panel-lvds-bridge {
> > +		compatible = "optologic,scx1001511ggc49", "panel-lvds";
> 
> > +		backlight = <&backlight_pwm3>;
> > +		data-mapping = "vesa-24";
> > +		height-mm = <136>;
> > +		width-mm = <217>;
> > +
> > +		panel-timing {
> > +			clock-frequency = <70000000>;
> 
> Looking at
> https://lore.kernel.org/linux-arm-kernel/20260623195741.495734-1-leoreis.costa@gmail.com/T/#mc4ed25e5253da6dc635fd3eddc317dac8f447f3e
> 
> 
> you are using three different clock-freq 69500000, 64500000 and
> 70000000 here.
> Could add some comment here, why freq is adjusted.

Just to confirm it, considering my last reply, do I understand correctly
that you want a v2 of this patch that adds this comment? In the end, these
are just values that we found to work consistently with the bridge, and
we're not sure if this comment would add much value.

Kind regards,
Leonardo

Re: [PATCH 1/1] arm64: dts: ti: k3-am69-aquila: Add Toradex DSI to LVDS adapter with the 10.1" V2 display

[Kumar, Udit]

Hi Leonardo,

On 9/9/2026 6:46 PM, Leonardo Costa wrote:
> Hi Udit,
> 
> On Sun, Sep 06, 2026 at 10:49:52AM +0530, Kumar, Udit wrote:
>> Hi Leonardo
>>
>> On 8/3/2026 11:04 PM, Leonardo Costa wrote:
>>> From: Leonardo Costa <leonardo.costa@toradex.com>
>>>
>>> Add a device tree overlay for the Toradex DSI to LVDS Adapter with the
>>> Toradex Capacitive Touch Display 10.1" LVDS V2. The adapter connects to the
>>> Aquila DSI_1 interface. It is based on the Texas Instruments SN65DSI84
>>> DSI-to-LVDS bridge and drives an Opto Logic SCX1001511GGC49 10.1" WXGA TFT
>>> LCD LVDS panel. Touch input is provided by an ILITEK ILI251x capacitive
>>> touch controller.
>>>
>>> Link: https://developer.toradex.com/hardware/accessories/add-ons/dsi-lvds-adapter
>>> Link: https://developer.toradex.com/hardware/accessories/displays/capacitive-touch-display-101inch-lvds
>>> Signed-off-by: Leonardo Costa <leonardo.costa@toradex.com>
>>> ---
>>>  arch/arm64/boot/dts/ti/Makefile               |   5 +
>>>  ...dsi-to-lvds-v2-panel-cap-touch-10inch.dtso | 153 ++++++++++++++++++
>>>  2 files changed, 158 insertions(+)
>>>  create mode 100644 arch/arm64/boot/dts/ti/k3-am69-aquila-dsi-to-lvds-v2-panel-cap-touch-10inch.dtso
>>>
>>> diff --git a/arch/arm64/boot/dts/ti/Makefile b/arch/arm64/boot/dts/ti/Makefile
>>> index f4d109ef6798a..8a59fc597aede 100644
>>> --- a/arch/arm64/boot/dts/ti/Makefile
>>> +++ b/arch/arm64/boot/dts/ti/Makefile
>>> @@ -218,6 +218,7 @@ dtb-$(CONFIG_ARCH_K3) += k3-am69-aquila-dev.dtb
>>> [..]
>>> +
>>> +	panel-lvds-bridge {
>>> +		compatible = "optologic,scx1001511ggc49", "panel-lvds";
>>
>>> +		backlight = <&backlight_pwm3>;
>>> +		data-mapping = "vesa-24";
>>> +		height-mm = <136>;
>>> +		width-mm = <217>;
>>> +
>>> +		panel-timing {
>>> +			clock-frequency = <70000000>;
>>
>> Looking at
>> https://lore.kernel.org/linux-arm-kernel/20260623195741.495734-1-leoreis.costa@gmail.com/T/#mc4ed25e5253da6dc635fd3eddc317dac8f447f3e
>>
>>
>> you are using three different clock-freq 69500000, 64500000 and
>> 70000000 here.
>> Could add some comment here, why freq is adjusted.
> 
> Just to confirm it, considering my last reply, do I understand correctly
> that you want a v2 of this patch that adds this comment? In the end, these
> are just values that we found to work consistently with the bridge, and
> we're not sure if this comment would add much value.

Still adding comments will be helpful.
If someone taking this panel code as reference on other SOC/Board, then
they will be aware of clock-freq needs to adjusted.

Thanks
Udit



> Kind regards,
> Leonardo