[PATCH v3 0/4] Add display overlays for imx8mp-phyboard-pollux

[PATCH v3 0/4] Add display overlays for imx8mp-phyboard-pollux

[Yannic Moog]

The phyBOARD-Pollux has an LVDS + backlight connector where one LVDS
channel is routed through.
Also, an expansion board (PEB-AV-10) may be connected to the baseboard
where the other LVDS channel (of the imx8mp SoC LVDS display bridge) is
routed to and there, too, an LVDS display may be connected.
However, both LVDS channels must not be used simultaneously as this is
not supported.
Currently, 2 displays are supported. Both are 10" touch displays, where the
edt is deprecated and kept for backward compatibility reasons. The powertip
panel is the successor to the edt panel and the current panel of choice.
The expansion board (PEB-AV-10) also has a 3.5 mm audio jack and thus
the expansion board may also be used for audio purposes without
displays.

---
Changes in v3:
- add patch which updates copyright and license
- update license identifier according to proper SPDX syntax
- explain in expansion board patch why a dtsi and dtso are introduced
- Link to v2: https://lore.kernel.org/r/20250924-imx8mp-pollux-display-overlays-v2-0-600f06b518b9@phytec.de

Changes in v2:
- Change license identifier of pollux and peb-av overlays.
- Link to v1: https://lore.kernel.org/r/20250915-imx8mp-pollux-display-overlays-v1-0-59508d578f0f@phytec.de

---
Yannic Moog (4):
      arm64: dts: im8mp-phy{board,core}: update license and copyright
      arm64: dts: imx8mp pollux: add display overlays
      arm64: dts: imx8mp pollux: add expansion board overlay
      arm64: dts: imx8mp pollux: add displays for expansion board

 arch/arm64/boot/dts/freescale/Makefile             |  15 ++
 .../imx8mp-phyboard-pollux-etml1010g3dra.dtso      |  44 +++++
 ...mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtso |  45 +++++
 ...8mp-phyboard-pollux-peb-av-10-ph128800t006.dtso |  45 +++++
 .../imx8mp-phyboard-pollux-peb-av-10.dtsi          | 198 +++++++++++++++++++++
 .../imx8mp-phyboard-pollux-peb-av-10.dtso          |   9 +
 .../imx8mp-phyboard-pollux-ph128800t006.dtso       |  45 +++++
 .../dts/freescale/imx8mp-phyboard-pollux-rdk.dts   |  53 ++----
 .../boot/dts/freescale/imx8mp-phycore-som.dtsi     |   4 +-
 9 files changed, 415 insertions(+), 43 deletions(-)
---
base-commit: e6b9dce0aeeb91dfc0974ab87f02454e24566182
change-id: 20250908-imx8mp-pollux-display-overlays-b4ab84966c66

Best regards,
-- 
Yannic Moog <y.moog@phytec.de>

[PATCH v3 1/4] arm64: dts: im8mp-phy{board,core}: update license and copyright

[Yannic Moog]

Update Copyright year and change license from GPL-2.0 to
GPL-2.0-or-later OR MIT. Use syntax as defined in the SPDX standard.

Signed-off-by: Yannic Moog <y.moog@phytec.de>
---
 arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 4 ++--
 arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi        | 4 ++--
 2 files changed, 4 insertions(+), 4 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
index 436152308642270c320e3ae3b21b9e46b923c043..6110c6a484d3f0b427ad372e1bd16063d1ce165f 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
  * Author: Teresa Remmet <t.remmet@phytec.de>
  */
 
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
index 04f724c6ec210bc2f382e6b9e2b13fe85d3926de..f6168984a31cca2b97344805c9474db900e3af3a 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
@@ -1,6 +1,6 @@
-// SPDX-License-Identifier: GPL-2.0
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
 /*
- * Copyright (C) 2020 PHYTEC Messtechnik GmbH
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
  * Author: Teresa Remmet <t.remmet@phytec.de>
  */
 

-- 
2.43.0

[PATCH v3 2/4] arm64: dts: imx8mp pollux: add display overlays

[Yannic Moog]

imx8mp-phyboard-pollux had a display baked into its board dts file.
However this approach does not truly discribe the hardware and is not
suitable when using different displays.
Move display specific description into an overlay and add the successor
display for the phyboard-pollux as an additional overlay.

Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
Signed-off-by: Yannic Moog <y.moog@phytec.de>
---
 arch/arm64/boot/dts/freescale/Makefile             |  6 +++
 .../imx8mp-phyboard-pollux-etml1010g3dra.dtso      | 44 +++++++++++++++++++
 .../imx8mp-phyboard-pollux-ph128800t006.dtso       | 45 ++++++++++++++++++++
 .../dts/freescale/imx8mp-phyboard-pollux-rdk.dts   | 49 +++++-----------------
 4 files changed, 105 insertions(+), 39 deletions(-)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 23535ed47631ca8f9db65bec5c07b6a7a7e36525..805ab9e5942bc9e2b9776e92412f56e969b6b39a 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -218,7 +218,13 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-navqp.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-nitrogen-enc-carrier-board.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-nitrogen-smarc-universal-board.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
+imx8mp-phyboard-pollux-etml1010g3dra-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
+	imx8mp-phyboard-pollux-etml1010g3dra.dtbo
+imx8mp-phyboard-pollux-ph128800t006-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
+	imx8mp-phyboard-pollux-ph128800t006.dtbo
 imx8mp-phyboard-pollux-rdk-no-eth-dtbs += imx8mp-phyboard-pollux-rdk.dtb imx8mp-phycore-no-eth.dtbo
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-etml1010g3dra.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-ph128800t006.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk-no-eth.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-basic.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-revb-hdmi.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-etml1010g3dra.dtso b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-etml1010g3dra.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..7a7f27d6bb1be6364cbab5d2fe45a365c7680fa8
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-etml1010g3dra.dtso
@@ -0,0 +1,44 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx8mp-clock.h>
+
+/dts-v1/;
+/plugin/;
+
+&backlight_lvds1 {
+	brightness-levels = <0 8 16 32 64 128 255>;
+	default-brightness-level = <8>;
+	enable-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+	num-interpolated-steps = <2>;
+	pwms = <&pwm3 0 50000 0>;
+	status = "okay";
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&lvds_bridge {
+	assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>, <&clk IMX8MP_VIDEO_PLL1>;
+	assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
+	/*
+	 * The LVDS panel uses 72.4 MHz pixel clock, set IMX8MP_VIDEO_PLL1 to
+	 * 72.4 * 7 = 506.8 MHz so the LDB serializer and LCDIFv3 scanout
+	 * engine can reach accurate pixel clock of exactly 72.4 MHz.
+	 */
+	assigned-clock-rates = <0>, <506800000>;
+	status = "okay";
+};
+
+&panel_lvds1 {
+	compatible = "edt,etml1010g3dra";
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-ph128800t006.dtso b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-ph128800t006.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..a39f83bf820490cf946849413cc968f9b0a86c96
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-ph128800t006.dtso
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx8mp-clock.h>
+
+/dts-v1/;
+/plugin/;
+
+&backlight_lvds1 {
+	brightness-levels = <0 8 16 32 64 128 255>;
+	default-brightness-level = <8>;
+	enable-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
+	num-interpolated-steps = <2>;
+	pwms = <&pwm3 0 66667 0>;
+	status = "okay";
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&lvds_bridge {
+	assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>, <&clk IMX8MP_VIDEO_PLL1>;
+	assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
+	/*
+	 * The LVDS panel uses 72.4 MHz pixel clock, set IMX8MP_VIDEO_PLL1 to
+	 * 66.5 * 7 = 465.5 MHz so the LDB serializer and LCDIFv3 scanout
+	 * engine can reach accurate pixel clock of exactly 66.5 MHz.
+	 */
+	assigned-clock-rates = <0>, <465500000>;
+	status = "okay";
+};
+
+
+&panel_lvds1 {
+	compatible = "powertip,ph128800t006-zhc01";
+	status = "okay";
+};
+
+&pwm3 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
index 6110c6a484d3f0b427ad372e1bd16063d1ce165f..a12556b7d76c2fcafc7f25e2d50ae2d386ed48d3 100644
--- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
@@ -8,7 +8,6 @@
 
 #include <dt-bindings/phy/phy-imx8-pcie.h>
 #include <dt-bindings/leds/leds-pca9532.h>
-#include <dt-bindings/pwm/pwm.h>
 #include <dt-bindings/thermal/thermal.h>
 #include "imx8mp-phycore-som.dtsi"
 
@@ -21,16 +20,12 @@ chosen {
 		stdout-path = &uart1;
 	};
 
-	backlight_lvds: backlight {
+	backlight_lvds1: backlight1 {
 		compatible = "pwm-backlight";
-		pinctrl-names = "default";
 		pinctrl-0 = <&pinctrl_lvds1>;
-		brightness-levels = <0 4 8 16 32 64 128 255>;
-		default-brightness-level = <11>;
-		enable-gpios = <&gpio2 20 GPIO_ACTIVE_LOW>;
-		num-interpolated-steps = <2>;
+		pinctrl-names = "default";
 		power-supply = <&reg_lvds1_reg_en>;
-		pwms = <&pwm3 0 50000 0>;
+		status = "disabled";
 	};
 
 	fan0: fan {
@@ -43,10 +38,11 @@ fan0: fan {
 		#cooling-cells = <2>;
 	};
 
-	panel1_lvds: panel-lvds {
-		compatible = "edt,etml1010g3dra";
-		backlight = <&backlight_lvds>;
+	panel_lvds1: panel-lvds1 {
+		/* compatible panel in overlay */
+		backlight = <&backlight_lvds1>;
 		power-supply = <&reg_vcc_3v3_sw>;
+		status = "disabled";
 
 		port {
 			panel1_in: endpoint {
@@ -232,32 +228,8 @@ led-3 {
 	};
 };
 
-&lcdif2 {
-	status = "okay";
-};
-
-&lvds_bridge {
-	status = "okay";
-
-	ports {
-		port@2 {
-			ldb_lvds_ch1: endpoint {
-				remote-endpoint = <&panel1_in>;
-			};
-		};
-	};
-};
-
-&media_blk_ctrl {
-	/*
-	 * The LVDS panel on this device uses 72.4 MHz pixel clock,
-	 * set IMX8MP_VIDEO_PLL1 to 72.4 * 7 = 506.8 MHz so the LDB
-	 * serializer and LCDIFv3 scanout engine can reach accurate
-	 * pixel clock of exactly 72.4 MHz.
-	 */
-	assigned-clock-rates = <500000000>, <200000000>,
-			       <0>, <0>, <500000000>,
-			       <506800000>;
+&ldb_lvds_ch1 {
+	remote-endpoint = <&panel1_in>;
 };
 
 &snvs_pwrkey {
@@ -282,9 +254,8 @@ &pcie {
 };
 
 &pwm3 {
-	status = "okay";
-	pinctrl-names = "default";
 	pinctrl-0 = <&pinctrl_pwm3>;
+	pinctrl-names = "default";
 };
 
 &rv3028 {

-- 
2.43.0

[PATCH v3 3/4] arm64: dts: imx8mp pollux: add expansion board overlay

[Yannic Moog]

An expansion board (PEB-AV-10) may be connected to the
imx8mp-phyboard-pollux. Its main purpose is to provide multimedia
interfaces, featuring a 3.5mm headphone jack, a USB-A port and LVDS as
well as backlight connectors.
Introduce the expansion board as dtsi, as it may be used standalone as
an expansion board, as well as in combination with display panels. These
display panels will include the dtsi.

Signed-off-by: Yannic Moog <y.moog@phytec.de>
---
 arch/arm64/boot/dts/freescale/Makefile             |   3 +
 .../imx8mp-phyboard-pollux-peb-av-10.dtsi          | 198 +++++++++++++++++++++
 .../imx8mp-phyboard-pollux-peb-av-10.dtso          |   9 +
 3 files changed, 210 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 805ab9e5942bc9e2b9776e92412f56e969b6b39a..9c121041128972d2239e2cc74df98b0bf7de1ac2 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -220,10 +220,13 @@ dtb-$(CONFIG_ARCH_MXC) += imx8mp-nitrogen-smarc-universal-board.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk.dtb
 imx8mp-phyboard-pollux-etml1010g3dra-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mp-phyboard-pollux-etml1010g3dra.dtbo
+imx8mp-phyboard-pollux-peb-av-10-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
+	imx8mp-phyboard-pollux-peb-av-10.dtbo
 imx8mp-phyboard-pollux-ph128800t006-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mp-phyboard-pollux-ph128800t006.dtbo
 imx8mp-phyboard-pollux-rdk-no-eth-dtbs += imx8mp-phyboard-pollux-rdk.dtb imx8mp-phycore-no-eth.dtbo
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-etml1010g3dra.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-peb-av-10.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-ph128800t006.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk-no-eth.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-basic.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10.dtsi
new file mode 100644
index 0000000000000000000000000000000000000000..bb740f845855ac06307de2c3835ebb5a03d40fa2
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10.dtsi
@@ -0,0 +1,198 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+#include <dt-bindings/clock/imx8mp-clock.h>
+#include <dt-bindings/gpio/gpio.h>
+#include "imx8mp-pinfunc.h"
+
+&{/} {
+	backlight_lvds0: backlight0 {
+		compatible = "pwm-backlight";
+		pinctrl-0 = <&pinctrl_lvds0>;
+		pinctrl-names = "default";
+		power-supply = <&reg_vcc_12v>;
+		status = "disabled";
+	};
+
+	panel_lvds0: panel-lvds0 {
+		backlight = <&backlight_lvds0>;
+		power-supply = <&reg_vcc_3v3_sw>;
+		status = "disabled";
+
+		port {
+			panel0_in: endpoint {
+				remote-endpoint = <&ldb_lvds_ch0>;
+			};
+		};
+	};
+
+	reg_vcc_12v: regulator-12v {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <12000000>;
+		regulator-min-microvolt = <12000000>;
+		regulator-name = "VCC_12V";
+	};
+
+	reg_vcc_1v8_audio: regulator-1v8 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <1800000>;
+		regulator-min-microvolt = <1800000>;
+		regulator-name = "VCC_1V8_Audio";
+	};
+
+	reg_vcc_3v3_analog: regulator-3v3 {
+		compatible = "regulator-fixed";
+		regulator-always-on;
+		regulator-boot-on;
+		regulator-max-microvolt = <3300000>;
+		regulator-min-microvolt = <3300000>;
+		regulator-name = "VCC_3V3_Analog";
+	};
+
+	sound {
+		compatible = "simple-audio-card";
+		simple-audio-card,name = "snd-peb-av-10";
+		simple-audio-card,format = "i2s";
+		simple-audio-card,bitclock-master = <&dailink_master>;
+		simple-audio-card,frame-master = <&dailink_master>;
+		simple-audio-card,mclk-fs = <32>;
+		simple-audio-card,widgets =
+			"Line", "Line In",
+			"Speaker", "Speaker",
+			"Microphone", "Microphone Jack",
+			"Headphone", "Headphone Jack";
+		simple-audio-card,routing =
+			"Speaker", "SPOP",
+			"Speaker", "SPOM",
+			"Headphone Jack", "HPLOUT",
+			"Headphone Jack", "HPROUT",
+			"LINE1L", "Line In",
+			"LINE1R", "Line In",
+			"MIC3R", "Microphone Jack",
+			"Microphone Jack", "Mic Bias";
+
+		simple-audio-card,cpu {
+			sound-dai = <&sai2>;
+		};
+
+		dailink_master: simple-audio-card,codec {
+			sound-dai = <&codec>;
+			clocks = <&clk IMX8MP_CLK_SAI2>;
+		};
+	};
+};
+
+&i2c4 {
+	clock-frequency = <400000>;
+	pinctrl-0 = <&pinctrl_i2c4>;
+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
+	pinctrl-names = "default", "gpio";
+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
+	#address-cells = <1>;
+	#size-cells = <0>;
+	status = "okay";
+
+	codec: codec@18 {
+		compatible = "ti,tlv320aic3007";
+		reg = <0x18>;
+		pinctrl-0 = <&pinctrl_tlv320>;
+		pinctrl-names = "default";
+		#sound-dai-cells = <0>;
+		reset-gpios = <&gpio4 28 GPIO_ACTIVE_LOW>;
+		ai3x-gpio-func = <0xd 0x0>;
+		ai3x-micbias-vg = <2>;
+		AVDD-supply = <&reg_vcc_3v3_analog>;
+		DRVDD-supply = <&reg_vcc_3v3_analog>;
+		DVDD-supply = <&reg_vcc_1v8_audio>;
+		IOVDD-supply = <&reg_vcc_3v3_sw>;
+	};
+
+	eeprom@57 {
+		compatible = "atmel,24c32";
+		reg = <0x57>;
+		pagesize = <32>;
+		vcc-supply = <&reg_vcc_3v3_sw>;
+	};
+};
+
+&ldb_lvds_ch0 {
+	remote-endpoint = <&panel0_in>;
+};
+
+&pwm4 {
+	pinctrl-0 = <&pinctrl_pwm4>;
+	pinctrl-names = "default";
+};
+
+&sai2 {
+	pinctrl-0 = <&pinctrl_sai2>;
+	pinctrl-names = "default";
+	assigned-clocks = <&clk IMX8MP_CLK_SAI2>;
+	assigned-clock-parents = <&clk IMX8MP_AUDIO_PLL1_OUT>;
+	assigned-clock-rates = <12288000>;
+	clocks = <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI2_IPG>,
+		 <&clk IMX8MP_CLK_DUMMY>,
+		 <&audio_blk_ctrl IMX8MP_CLK_AUDIOMIX_SAI2_MCLK1>,
+		 <&clk IMX8MP_CLK_DUMMY>,
+		 <&clk IMX8MP_CLK_DUMMY>,
+		 <&clk IMX8MP_AUDIO_PLL1_OUT>,
+		 <&clk IMX8MP_AUDIO_PLL2_OUT>;
+	clock-names = "bus", "mclk0", "mclk1", "mclk2", "mclk3", "pll8k",
+		      "pll11k";
+	#sound-dai-cells = <0>;
+	fsl,sai-mclk-direction-output;
+	fsl,sai-synchronous-rx;
+	status = "okay";
+};
+
+&iomuxc {
+	pinctrl_i2c4: i2c4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__I2C4_SCL		0x400001c2
+			MX8MP_IOMUXC_I2C4_SDA__I2C4_SDA		0x400001c2
+		>;
+	};
+
+	pinctrl_i2c4_gpio: i2c4gpiogrp {
+		fsl,pins = <
+			MX8MP_IOMUXC_I2C4_SCL__GPIO5_IO20	0x1e2
+			MX8MP_IOMUXC_I2C4_SDA__GPIO5_IO21	0x1e2
+		>;
+	};
+
+	pinctrl_lvds0: lvds0grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_TXD__GPIO5_IO01	0x12
+		>;
+	};
+
+	pinctrl_pwm4: pwm4grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_MCLK__PWM4_OUT	0x12
+		>;
+	};
+
+	pinctrl_sai2: sai2grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI2_MCLK__AUDIOMIX_SAI2_MCLK	0xd6
+			MX8MP_IOMUXC_SAI2_RXFS__AUDIOMIX_SAI2_RX_SYNC	0xd6
+			MX8MP_IOMUXC_SAI2_TXC__AUDIOMIX_SAI2_TX_BCLK	0xd6
+			MX8MP_IOMUXC_SAI2_TXD0__AUDIOMIX_SAI2_TX_DATA00	0xd6
+			MX8MP_IOMUXC_SAI2_RXD0__AUDIOMIX_SAI2_RX_DATA00 0xd6
+		>;
+	};
+
+	pinctrl_tlv320: tlv320grp {
+		fsl,pins = <
+			MX8MP_IOMUXC_SAI3_RXFS__GPIO4_IO28	0x16
+			MX8MP_IOMUXC_SAI2_RXC__GPIO4_IO22	0x16
+		>;
+	};
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10.dtso b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..95078618ee095af5c8b09f62945c125e69990baf
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10.dtso
@@ -0,0 +1,9 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include "imx8mp-phyboard-pollux-peb-av-10.dtsi"

-- 
2.43.0

[PATCH v3 4/4] arm64: dts: imx8mp pollux: add displays for expansion board

[Yannic Moog]

The same displays that can be connected directly to the
imx8mp-phyboard-pollux can also be connected to the expansion board
PEB-AV-10. For displays connected to the expansion board, a second LVDS
channel of the i.MX 8M Plus SoC is used and only a single display
connected to the SoC LVDS display bridge at a given time is supported.

Signed-off-by: Yannic Moog <y.moog@phytec.de>
---
 arch/arm64/boot/dts/freescale/Makefile             |  6 +++
 ...mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtso | 45 ++++++++++++++++++++++
 ...8mp-phyboard-pollux-peb-av-10-ph128800t006.dtso | 45 ++++++++++++++++++++++
 3 files changed, 96 insertions(+)

diff --git a/arch/arm64/boot/dts/freescale/Makefile b/arch/arm64/boot/dts/freescale/Makefile
index 9c121041128972d2239e2cc74df98b0bf7de1ac2..e4b097446440f41785dd1a0e5d354796e800ee76 100644
--- a/arch/arm64/boot/dts/freescale/Makefile
+++ b/arch/arm64/boot/dts/freescale/Makefile
@@ -222,11 +222,17 @@ imx8mp-phyboard-pollux-etml1010g3dra-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mp-phyboard-pollux-etml1010g3dra.dtbo
 imx8mp-phyboard-pollux-peb-av-10-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mp-phyboard-pollux-peb-av-10.dtbo
+imx8mp-phyboard-pollux-peb-av-10-etml1010g3dra-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
+	imx8mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtbo
+imx8mp-phyboard-pollux-peb-av-10-ph128800t006-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
+	imx8mp-phyboard-pollux-peb-av-10-ph128800t006.dtbo
 imx8mp-phyboard-pollux-ph128800t006-dtbs += imx8mp-phyboard-pollux-rdk.dtb \
 	imx8mp-phyboard-pollux-ph128800t006.dtbo
 imx8mp-phyboard-pollux-rdk-no-eth-dtbs += imx8mp-phyboard-pollux-rdk.dtb imx8mp-phycore-no-eth.dtbo
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-etml1010g3dra.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-peb-av-10.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtb
+dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-peb-av-10-ph128800t006.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-ph128800t006.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-phyboard-pollux-rdk-no-eth.dtb
 dtb-$(CONFIG_ARCH_MXC) += imx8mp-skov-basic.dtb
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtso b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..aceb5b6056ef1298ad9e105e673c7ab403411ab0
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10-etml1010g3dra.dtso
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx8mp-clock.h>
+#include "imx8mp-phyboard-pollux-peb-av-10.dtsi"
+
+&backlight_lvds0 {
+	brightness-levels = <0 8 16 32 64 128 255>;
+	default-brightness-level = <8>;
+	enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	num-interpolated-steps = <2>;
+	pwms = <&pwm4 0 50000 0>;
+	status = "okay";
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&lvds_bridge {
+	assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>, <&clk IMX8MP_VIDEO_PLL1>;
+	assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
+	/*
+	 * The LVDS panel uses 72.4 MHz pixel clock, set IMX8MP_VIDEO_PLL1 to
+	 * 72.4 * 7 = 506.8 MHz so the LDB serializer and LCDIFv3 scanout
+	 * engine can reach accurate pixel clock of exactly 72.4 MHz.
+	 */
+	assigned-clock-rates = <0>, <506800000>;
+	status = "okay";
+};
+
+&panel_lvds0 {
+	compatible = "edt,etml1010g3dra";
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};
diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10-ph128800t006.dtso b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10-ph128800t006.dtso
new file mode 100644
index 0000000000000000000000000000000000000000..559286f384be452f1c953689e03249fbea24fac5
--- /dev/null
+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-peb-av-10-ph128800t006.dtso
@@ -0,0 +1,45 @@
+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
+/*
+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH
+ */
+
+/dts-v1/;
+/plugin/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/clock/imx8mp-clock.h>
+#include "imx8mp-phyboard-pollux-peb-av-10.dtsi"
+
+&backlight_lvds0 {
+	brightness-levels = <0 8 16 32 64 128 255>;
+	default-brightness-level = <8>;
+	enable-gpios = <&gpio5 1 GPIO_ACTIVE_HIGH>;
+	num-interpolated-steps = <2>;
+	pwms = <&pwm4 0 66667 0>;
+	status = "okay";
+};
+
+&lcdif2 {
+	status = "okay";
+};
+
+&lvds_bridge {
+	assigned-clocks = <&clk IMX8MP_CLK_MEDIA_LDB>, <&clk IMX8MP_VIDEO_PLL1>;
+	assigned-clock-parents = <&clk IMX8MP_VIDEO_PLL1_OUT>;
+	/*
+	 * The LVDS panel uses 66.5 MHz pixel clock, set IMX8MP_VIDEO_PLL1 to
+	 * 66.5 * 7 = 465.5 MHz so the LDB serializer and LCDIFv3 scanout
+	 * engine can reach accurate pixel clock of exactly 66.5 MHz.
+	 */
+	assigned-clock-rates = <0>, <465500000>;
+	status = "okay";
+};
+
+&panel_lvds0 {
+	compatible = "powertip,ph128800t006-zhc01";
+	status = "okay";
+};
+
+&pwm4 {
+	status = "okay";
+};

-- 
2.43.0

Re: [PATCH v3 1/4] arm64: dts: im8mp-phy{board,core}: update license and copyright

[Frank Li]

On Wed, Oct 01, 2025 at 02:33:51PM +0200, Yannic Moog wrote:
> Update Copyright year and change license from GPL-2.0 to
> GPL-2.0-or-later OR MIT. Use syntax as defined in the SPDX standard.
>
> Signed-off-by: Yannic Moog <y.moog@phytec.de>
> ---
>  arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 4 ++--
>  arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi        | 4 ++--
>  2 files changed, 4 insertions(+), 4 deletions(-)
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> index 436152308642270c320e3ae3b21b9e46b923c043..6110c6a484d3f0b427ad372e1bd16063d1ce165f 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> @@ -1,6 +1,6 @@
> -// SPDX-License-Identifier: GPL-2.0
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
>  /*
> - * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> + * Copyright (C) 2025 PHYTEC Messtechnik GmbH

copyright need keep original years

Copyright (C) 2020, 2025 PHYTEC Messtechnik GmbH

Frank
>   * Author: Teresa Remmet <t.remmet@phytec.de>
>   */
>
> diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> index 04f724c6ec210bc2f382e6b9e2b13fe85d3926de..f6168984a31cca2b97344805c9474db900e3af3a 100644
> --- a/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> +++ b/arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi
> @@ -1,6 +1,6 @@
> -// SPDX-License-Identifier: GPL-2.0
> +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
>  /*
> - * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> + * Copyright (C) 2025 PHYTEC Messtechnik GmbH
>   * Author: Teresa Remmet <t.remmet@phytec.de>
>   */
>
>
> --
> 2.43.0
>

Re: [PATCH v3 1/4] arm64: dts: im8mp-phy{board,core}: update license and copyright

[Peng Fan]

On Wed, Oct 01, 2025 at 02:33:51PM +0200, Yannic Moog wrote:
>Update Copyright year and change license from GPL-2.0 to
>GPL-2.0-or-later OR MIT. Use syntax as defined in the SPDX standard.
>
>Signed-off-by: Yannic Moog <y.moog@phytec.de>
>---
> arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 4 ++--
> arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi        | 4 ++--
> 2 files changed, 4 insertions(+), 4 deletions(-)
>
>diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
>index 436152308642270c320e3ae3b21b9e46b923c043..6110c6a484d3f0b427ad372e1bd16063d1ce165f 100644
>--- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
>+++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
>@@ -1,6 +1,6 @@
>-// SPDX-License-Identifier: GPL-2.0
>+// SPDX-License-Identifier: GPL-2.0-or-later OR MIT

> /*
>- * Copyright (C) 2020 PHYTEC Messtechnik GmbH
>+ * Copyright (C) 2025 PHYTEC Messtechnik GmbH

Is this expected? In normal case, this might be "2020, 2025".

BTW: You may also need to collect A-b from contributors that is not in phytec.

Regards
Peng

Re: [PATCH v3 2/4] arm64: dts: imx8mp pollux: add display overlays

[Peng Fan]

On Wed, Oct 01, 2025 at 02:33:52PM +0200, Yannic Moog wrote:
>imx8mp-phyboard-pollux had a display baked into its board dts file.
>However this approach does not truly discribe the hardware and is not
>suitable when using different displays.
>Move display specific description into an overlay and add the successor
>display for the phyboard-pollux as an additional overlay.
>
>Reviewed-by: Teresa Remmet <t.remmet@phytec.de>
>Signed-off-by: Yannic Moog <y.moog@phytec.de>

Reviewed-by: Peng Fan <peng.fan@nxp.com>

Re: [PATCH v3 3/4] arm64: dts: imx8mp pollux: add expansion board overlay

[Peng Fan]

On Wed, Oct 01, 2025 at 02:33:53PM +0200, Yannic Moog wrote:
>An expansion board (PEB-AV-10) may be connected to the
>imx8mp-phyboard-pollux. Its main purpose is to provide multimedia
>interfaces, featuring a 3.5mm headphone jack, a USB-A port and LVDS as
>well as backlight connectors.
>Introduce the expansion board as dtsi, as it may be used standalone as
>an expansion board, as well as in combination with display panels. These
>display panels will include the dtsi.
>
>Signed-off-by: Yannic Moog <y.moog@phytec.de>
>---
....
>+
>+&i2c4 {
>+	clock-frequency = <400000>;
>+	pinctrl-0 = <&pinctrl_i2c4>;
>+	pinctrl-1 = <&pinctrl_i2c4_gpio>;
>+	pinctrl-names = "default", "gpio";
>+	scl-gpios = <&gpio5 20 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;
>+	sda-gpios = <&gpio5 21 (GPIO_ACTIVE_HIGH | GPIO_OPEN_DRAIN)>;

>+	#address-cells = <1>;
>+	#size-cells = <0>;
This two properties are in imx8mp.dts, no need add here. Otherwise,

Reviewed-by: Peng Fan <peng.fan@nxp.com>

Re: [PATCH v3 4/4] arm64: dts: imx8mp pollux: add displays for expansion board

[Peng Fan]

On Wed, Oct 01, 2025 at 02:33:54PM +0200, Yannic Moog wrote:
>The same displays that can be connected directly to the
>imx8mp-phyboard-pollux can also be connected to the expansion board
>PEB-AV-10. For displays connected to the expansion board, a second LVDS
>channel of the i.MX 8M Plus SoC is used and only a single display
>connected to the SoC LVDS display bridge at a given time is supported.
>
>Signed-off-by: Yannic Moog <y.moog@phytec.de>

Reviewed-by: Peng Fan <peng.fan@nxp.com>

Re: [PATCH v3 1/4] arm64: dts: im8mp-phy{board,core}: update license and copyright

[Yannic Moog]

Am Samstag, dem 11.10.2025 um 21:06 +0800 schrieb Peng Fan:
> On Wed, Oct 01, 2025 at 02:33:51PM +0200, Yannic Moog wrote:
> > Update Copyright year and change license from GPL-2.0 to
> > GPL-2.0-or-later OR MIT. Use syntax as defined in the SPDX standard.
> > 
> > Signed-off-by: Yannic Moog <y.moog@phytec.de>
> > ---
> > arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts | 4 ++--
> > arch/arm64/boot/dts/freescale/imx8mp-phycore-som.dtsi        | 4 ++--
> > 2 files changed, 4 insertions(+), 4 deletions(-)
> > 
> > diff --git a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> > b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> > index
> > 436152308642270c320e3ae3b21b9e46b923c043..6110c6a484d3f0b427ad372e1bd16063d1
> > ce165f 100644
> > --- a/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> > +++ b/arch/arm64/boot/dts/freescale/imx8mp-phyboard-pollux-rdk.dts
> > @@ -1,6 +1,6 @@
> > -// SPDX-License-Identifier: GPL-2.0
> > +// SPDX-License-Identifier: GPL-2.0-or-later OR MIT
> 
> > /*
> > - * Copyright (C) 2020 PHYTEC Messtechnik GmbH
> > + * Copyright (C) 2025 PHYTEC Messtechnik GmbH
> 
> Is this expected? In normal case, this might be "2020, 2025".

No, it was an error by me.

> 
> BTW: You may also need to collect A-b from contributors that is not in phytec.

Got it, thanks.

Yannic

> 
> Regards
> Peng