From: Sean Neakums <sneakums@zork.net>
To: Andrew Morton <akpm@osdl.org>
Cc: linux-kernel@vger.kernel.org
Subject: i810 AGP fails to initialise (was Re: 2.6.6-mm2)
Date: Thu, 13 May 2004 13:54:03 +0100 [thread overview]
Message-ID: <6usme4v66s.fsf@zork.zork.net> (raw)
In-Reply-To: <20040513032736.40651f8e.akpm@osdl.org> (Andrew Morton's message of "Thu, 13 May 2004 03:27:36 -0700")
Andrew Morton <akpm@osdl.org> writes:
> bk-agpgart.patch
>
With this patch applied, agpgart doesn't initialise on my Dell
OptiPlex GX110, causing drm to fail to initialise.
Linux agpgart interface v0.100 (c) Dave Jones
[drm:i810_probe] *ERROR* Cannot initialize the agpgart module.
Here are the messages from successful initialisation with the patch
reverted.
Linux agpgart interface v0.100 (c) Dave Jones
agpgart: Detected an Intel i810 E Chipset.
agpgart: Maximum main memory to use for agp memory: 320M
agpgart: detected 4MB dedicated video ram.
agpgart: AGP aperture is 64M @ 0xf8000000
[drm] Initialized i810 1.4.0 20030605 on minor 0: Intel Corp. 82810E DC-133 CGC [Chipset Graphics Controller]
Here is the lspci -vvvv output:
0000:00:00.0 Host bridge: Intel Corp. 82810E DC-133 GMCH [Graphics Memory Controller Hub] (rev 03)
Subsystem: Dell Computer Corporation: Unknown device 00b4
Control: I/O- Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort+ >SERR- <PERR-
Latency: 0
0000:00:01.0 VGA compatible controller: Intel Corp. 82810E DC-133 CGC [Chipset Graphics Controller] (rev 03) (prog-if 00 [VGA])
Subsystem: Dell Computer Corporation: Unknown device 00b4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin A routed to IRQ 9
Region 0: Memory at f8000000 (32-bit, prefetchable)
Region 1: Memory at ff000000 (32-bit, non-prefetchable) [size=512K]
Capabilities: [dc] Power Management version 1
Flags: PMEClk- DSI+ D1- D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-)
Status: D0 PME-Enable- DSel=0 DScale=0 PME-
0000:00:1e.0 PCI bridge: Intel Corp. 82801AA PCI Bridge (rev 02) (prog-if 00 [Normal decode])
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=fast >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Bus: primary=00, secondary=01, subordinate=01, sec-latency=64
I/O behind bridge: 0000e000-0000efff
Memory behind bridge: fd000000-feffffff
Prefetchable memory behind bridge: fff00000-000fffff
BridgeCtl: Parity- SERR+ NoISA+ VGA- MAbort- >Reset- FastB2B-
0000:00:1f.0 ISA bridge: Intel Corp. 82801AA ISA Bridge (LPC) (rev 02)
Control: I/O+ Mem+ BusMaster+ SpecCycle+ MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
0000:00:1f.1 IDE interface: Intel Corp. 82801AA IDE (rev 02) (prog-if 80 [Master])
Subsystem: Intel Corp. 82801AA IDE
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Region 4: I/O ports at ffa0 [size=16]
0000:00:1f.2 USB Controller: Intel Corp. 82801AA USB (rev 02) (prog-if 00 [UHCI])
Subsystem: Intel Corp. 82801AA USB
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin D routed to IRQ 11
Region 4: I/O ports at ff80 [size=32]
0000:00:1f.3 SMBus: Intel Corp. 82801AA SMBus (rev 02)
Subsystem: Intel Corp. 82801AA SMBus
Control: I/O+ Mem- BusMaster- SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Interrupt: pin B routed to IRQ 10
Region 4: I/O ports at dcd0 [size=16]
0000:00:1f.5 Multimedia audio controller: Intel Corp. 82801AA AC'97 Audio (rev 02)
Subsystem: Dell Computer Corporation: Unknown device 00b4
Control: I/O+ Mem- BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B-
Status: Cap- 66MHz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 0
Interrupt: pin B routed to IRQ 10
Region 0: I/O ports at d800
Region 1: I/O ports at dc80 [size=64]
0000:01:0c.0 Ethernet controller: 3Com Corporation 3c905C-TX/TX-M [Tornado] (rev 78)
Subsystem: Dell Computer Corporation: Unknown device 00b4
Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV+ VGASnoop- ParErr- Stepping- SERR+ FastB2B-
Status: Cap+ 66MHz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR-
Latency: 64 (2500ns min, 2500ns max), Cache Line Size: 0x08 (32 bytes)
Interrupt: pin A routed to IRQ 5
Region 0: I/O ports at e480 [size=fe000000]
Region 1: Memory at fdffe400 (32-bit, non-prefetchable) [size=128]
Expansion ROM at 00020000 [disabled]
Capabilities: [dc] Power Management version 2
Flags: PMEClk- DSI- D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+)
Status: D0 PME-Enable- DSel=0 DScale=2 PME-
next prev parent reply other threads:[~2004-05-13 12:54 UTC|newest]
Thread overview: 54+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-05-13 10:27 2.6.6-mm2 Andrew Morton
2004-05-13 10:45 ` 2.6.6-mm2 Christoph Hellwig
2004-05-13 10:51 ` 2.6.6-mm2 Andrew Morton
2004-05-13 11:12 ` 2.6.6-mm2 Christoph Hellwig
2004-05-13 11:25 ` 2.6.6-mm2 Andrew Morton
2004-05-13 13:18 ` 2.6.6-mm2 Adrian Bunk
2004-05-13 13:39 ` 2.6.6-mm2 Chris Mason
2004-05-13 14:09 ` 2.6.6-mm2 Adrian Bunk
2004-05-17 20:52 ` 2.6.6-mm2 Bill Davidsen
2004-05-14 7:30 ` 2.6.6-mm2 Ian Kent
2004-05-13 14:15 ` 2.6.6-mm2 Adrian Bunk
2004-05-13 19:18 ` 2.6.6-mm2 Chris Wright
2004-05-13 19:29 ` 2.6.6-mm2 Andrew Morton
2004-05-13 19:35 ` 2.6.6-mm2 Chris Wright
2004-05-13 19:38 ` 2.6.6-mm2 Andrew Morton
2004-05-13 19:42 ` 2.6.6-mm2 Chris Wright
2004-05-14 19:14 ` 2.6.6-mm2 Andrea Arcangeli
2004-05-14 20:58 ` 2.6.6-mm2 Chris Wright
2004-05-15 2:43 ` 2.6.6-mm2 Andrea Arcangeli
2004-05-15 7:43 ` 2.6.6-mm2 Hugh Dickins
2004-05-14 19:06 ` 2.6.6-mm2 Kevin O'Connor
2004-05-14 19:36 ` 2.6.6-mm2 Chris Wright
2004-05-14 19:42 ` 2.6.6-mm2 Kevin O'Connor
2004-05-13 10:53 ` 2.6.6-mm2, usb ehci warnings/error? Prakash K. Cheemplavam
2004-05-13 12:11 ` 2.6.6-mm-rc3-mm2 USB 2.0 after suspend issue Ari Pollak
2004-05-13 12:14 ` 2.6.6-mm2 Matt H.
2004-05-13 18:24 ` 2.6.6-mm2 Andrew Morton
2004-05-13 22:40 ` 2.6.6-mm2 Greg KH
2004-05-13 12:54 ` Sean Neakums [this message]
2004-05-13 13:53 ` i810 AGP fails to initialise (was Re: 2.6.6-mm2) Dave Jones
2004-05-13 13:58 ` Andi Kleen
2004-05-13 14:02 ` Sean Neakums
2004-05-13 15:41 ` Andi Kleen
2004-05-14 3:47 ` Clemens Schwaighofer
2004-05-14 7:42 ` Sean Neakums
2004-05-15 9:52 ` Sean Neakums
2004-05-17 8:49 ` Sean Neakums
2004-05-17 10:01 ` Andi Kleen
2004-05-17 11:04 ` Sean Neakums
2004-05-17 11:46 ` Andi Kleen
2004-05-17 12:37 ` Sean Neakums
2004-05-13 13:38 ` 2.6.6-mm2: EFI_VARS=m is broken Adrian Bunk
2004-05-13 15:03 ` Matt Domsch
2004-05-13 13:42 ` 2.6.6-mm2 Paolo Ornati
2004-05-13 14:01 ` 2.6.6-mm2: bk-driver-core-module-fix.patch no longer required Adrian Bunk
2004-05-13 14:36 ` Paolo Ornati
2004-05-13 15:07 ` 2.6.6-mm2 Lorenzo Allegrucci
2004-05-13 18:55 ` 2.6.6-mm2 Andrew Morton
2004-05-13 19:41 ` 2.6.6-mm2 Lorenzo Allegrucci
2004-05-14 17:48 ` 2.6.6-mm2 R. J. Wysocki
2004-05-14 17:47 ` 2.6.6-mm2 Christoph Hellwig
2004-05-14 21:20 ` 2.6.6-mm2 R. J. Wysocki
2004-05-14 23:56 ` 2.6.6-mm2 Joseph Fannin
2004-05-14 23:58 ` 2.6.6-mm2 Chris Wright
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=6usme4v66s.fsf@zork.zork.net \
--to=sneakums@zork.net \
--cc=akpm@osdl.org \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®