* [PATCH v6 1/5] arm64: dts: qcom: pmk8550: add VADC node
2026-07-21 15:31 [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Neil Armstrong
@ 2026-07-21 15:31 ` Neil Armstrong
2026-07-21 15:31 ` [PATCH v6 2/5] arm64: dts: qcom: sm8550-qrd: add SPMI ADC channels and thermal nodes Neil Armstrong
` (4 subsequent siblings)
5 siblings, 0 replies; 11+ messages in thread
From: Neil Armstrong @ 2026-07-21 15:31 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Neil Armstrong, Konrad Dybcio
Add the VADC node and the initial pmk8550 adc channels.
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/pmk8550.dtsi | 30 ++++++++++++++++++++++++++++++
1 file changed, 30 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/pmk8550.dtsi b/arch/arm64/boot/dts/qcom/pmk8550.dtsi
index 3049eb6b46d7..3a9d9f7c3742 100644
--- a/arch/arm64/boot/dts/qcom/pmk8550.dtsi
+++ b/arch/arm64/boot/dts/qcom/pmk8550.dtsi
@@ -7,6 +7,7 @@
#include <dt-bindings/input/linux-event-codes.h>
#include <dt-bindings/interrupt-controller/irq.h>
#include <dt-bindings/spmi/spmi.h>
+#include "qcom-adc5-gen3.h"
/ {
reboot-mode {
@@ -64,6 +65,35 @@ reboot_reason: reboot-reason@48 {
};
};
+ pmk8550_vadc: adc@9000 {
+ compatible = "qcom,spmi-adc5-gen3";
+ reg = <0x9000>, <0x9100>;
+ interrupts-extended = <&spmi_bus 0x0 0x90 0x1 IRQ_TYPE_EDGE_RISING>,
+ <&spmi_bus 0x0 0x91 0x1 IRQ_TYPE_EDGE_RISING>;
+ #address-cells = <1>;
+ #size-cells = <0>;
+ #io-channel-cells = <1>;
+ #thermal-sensor-cells = <1>;
+
+ channel@0 {
+ reg = <ADC5_GEN3_REF_GND(0)>;
+ label = "pmk8550_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@1 {
+ reg = <ADC5_GEN3_1P25VREF(0)>;
+ label = "pmk8550_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@3 {
+ reg = <ADC5_GEN3_DIE_TEMP(0)>;
+ label = "pmk8550_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+ };
+
pmk8550_gpios: gpio@b800 {
compatible = "qcom,pmk8550-gpio", "qcom,spmi-gpio";
reg = <0xb800>;
--
2.34.1
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH v6 2/5] arm64: dts: qcom: sm8550-qrd: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Neil Armstrong
2026-07-21 15:31 ` [PATCH v6 1/5] arm64: dts: qcom: pmk8550: add VADC node Neil Armstrong
@ 2026-07-21 15:31 ` Neil Armstrong
2026-07-29 9:08 ` Konrad Dybcio
2026-07-21 15:31 ` [PATCH v6 3/5] arm64: dts: qcom: sm8550-hdk: " Neil Armstrong
` (3 subsequent siblings)
5 siblings, 1 reply; 11+ messages in thread
From: Neil Armstrong @ 2026-07-21 15:31 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Neil Armstrong
Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
other PMICS on the system.
The thermal nodes are sorted by the sensor channel to be
coherent with the system thermal nodes ordering.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8550-qrd.dts | 277 ++++++++++++++++++++++++++++++++
1 file changed, 277 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
index f2effa55d819..144e105b734f 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-qrd.dts
@@ -205,6 +205,92 @@ platform {
};
};
+ thermal-zones {
+ skin-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ cam-flash-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wlan-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ pa-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ rear-tof-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ usb-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wls-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
regulator-name = "vph_pwr";
@@ -995,27 +1081,218 @@ led@3 {
};
};
+&pm8550_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(1)>;
+ io-channel-names = "thermal";
+};
+
&pm8550b_eusb2_repeater {
vdd18-supply = <&vreg_l15b_1p8>;
vdd3-supply = <&vreg_l5b_3p1>;
};
+&pm8550b_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(7)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_c {
status = "okay";
};
+&pm8550vs_c_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(2)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_d {
status = "okay";
};
+&pm8550vs_d_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(3)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_e {
status = "okay";
};
+&pm8550vs_e_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(4)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_g {
status = "okay";
};
+&pm8550vs_g_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(6)>;
+ io-channel-names = "thermal";
+};
+
+&pm8550ve_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ io-channel-names = "thermal";
+};
+
+&pmk8550_vadc {
+ /* PM8550 Channel nodes */
+ channel@100 {
+ reg = <ADC5_GEN3_REF_GND(1)>;
+ label = "pm8550_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@101 {
+ reg = <ADC5_GEN3_1P25VREF(1)>;
+ label = "pm8550_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@103 {
+ reg = <ADC5_GEN3_DIE_TEMP(1)>;
+ label = "pm8550_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@144 {
+ reg = <ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+ label = "pm8550_msm_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@145 {
+ reg = <ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+ label = "pm8550_cam_flash_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@146 {
+ reg = <ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+ label = "pm8550_wlan_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@147 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+ label = "pm8550_pa_therm_1";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@148 {
+ reg = <ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+ label = "pm8550_rear_tof_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@18e {
+ reg = <ADC5_GEN3_VPH_PWR(1)>;
+ label = "pm8550_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ /* PM8550VS_C Channel nodes */
+ channel@203 {
+ reg = <ADC5_GEN3_DIE_TEMP(2)>;
+ label = "pm8550vs_c_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_D Channel nodes */
+ channel@303 {
+ reg = <ADC5_GEN3_DIE_TEMP(3)>;
+ label = "pm8550vs_d_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_E Channel nodes */
+ channel@403 {
+ reg = <ADC5_GEN3_DIE_TEMP(4)>;
+ label = "pm8550vs_e_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VE Channel nodes */
+ channel@503 {
+ reg = <ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ label = "pm8550ve_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_G Channel nodes */
+ channel@603 {
+ reg = <ADC5_GEN3_DIE_TEMP(6)>;
+ label = "pm8550vs_g_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550B Channel nodes */
+ channel@700 {
+ reg = <ADC5_GEN3_REF_GND(7)>;
+ label = "pm8550b_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@701 {
+ reg = <ADC5_GEN3_1P25VREF(7)>;
+ label = "pm8550b_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@703 {
+ reg = <ADC5_GEN3_DIE_TEMP(7)>;
+ label = "pm8550b_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@747 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+ label = "pm8550b_usb_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@749 {
+ reg = <ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+ label = "pm8550b_wls_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <15>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@78e {
+ reg = <ADC5_GEN3_VPH_PWR(7)>;
+ label = "pm8550b_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ channel@78f {
+ reg = <ADC5_GEN3_VBAT_SNS_QBG(7)>;
+ label = "pm8550b_vbat_sns_qbg";
+ qcom,pre-scaling = <1 6>;
+ };
+};
+
&pon_pwrkey {
status = "okay";
};
--
2.34.1
^ permalink raw reply [flat|nested] 11+ messages in thread* [PATCH v6 3/5] arm64: dts: qcom: sm8550-hdk: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Neil Armstrong
2026-07-21 15:31 ` [PATCH v6 1/5] arm64: dts: qcom: pmk8550: add VADC node Neil Armstrong
2026-07-21 15:31 ` [PATCH v6 2/5] arm64: dts: qcom: sm8550-qrd: add SPMI ADC channels and thermal nodes Neil Armstrong
@ 2026-07-21 15:31 ` Neil Armstrong
2026-07-21 15:37 ` Konrad Dybcio
2026-07-21 15:31 ` [PATCH v6 4/5] arm64: dts: qcom: sm8650-qrd: " Neil Armstrong
` (2 subsequent siblings)
5 siblings, 1 reply; 11+ messages in thread
From: Neil Armstrong @ 2026-07-21 15:31 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Neil Armstrong
Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
other PMICS on the system.
The thermal nodes are sorted by the sensor channel to be
coherent with the system thermal nodes ordering.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8550-hdk.dts | 277 ++++++++++++++++++++++++++++++++
1 file changed, 277 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
index b79558938552..58c71ac67da5 100644
--- a/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8550-hdk.dts
@@ -280,6 +280,92 @@ platform {
};
};
+ thermal-zones {
+ skin-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ cam-flash-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wlan-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ pa-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ rear-tof-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ usb-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wls-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
wcn7850-pmu {
compatible = "qcom,wcn7850-pmu";
@@ -1100,27 +1186,218 @@ led@3 {
};
};
+&pm8550_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(1)>;
+ io-channel-names = "thermal";
+};
+
&pm8550b_eusb2_repeater {
vdd18-supply = <&vreg_l15b_1p8>;
vdd3-supply = <&vreg_l5b_3p1>;
};
+&pm8550b_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(7)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_c {
status = "okay";
};
+&pm8550vs_c_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(2)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_d {
status = "okay";
};
+&pm8550vs_d_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(3)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_e {
status = "okay";
};
+&pm8550vs_e_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(4)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_g {
status = "okay";
};
+&pm8550vs_g_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(6)>;
+ io-channel-names = "thermal";
+};
+
+&pm8550ve_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ io-channel-names = "thermal";
+};
+
+&pmk8550_vadc {
+ /* PM8550 Channel nodes */
+ channel@100 {
+ reg = <ADC5_GEN3_REF_GND(1)>;
+ label = "pm8550_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@101 {
+ reg = <ADC5_GEN3_1P25VREF(1)>;
+ label = "pm8550_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@103 {
+ reg = <ADC5_GEN3_DIE_TEMP(1)>;
+ label = "pm8550_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@144 {
+ reg = <ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+ label = "pm8550_msm_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@145 {
+ reg = <ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+ label = "pm8550_cam_flash_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@146 {
+ reg = <ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+ label = "pm8550_wlan_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@147 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+ label = "pm8550_pa_therm_1";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@148 {
+ reg = <ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+ label = "pm8550_rear_tof_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@18e {
+ reg = <ADC5_GEN3_VPH_PWR(1)>;
+ label = "pm8550_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ /* PM8550VS_C Channel nodes */
+ channel@203 {
+ reg = <ADC5_GEN3_DIE_TEMP(2)>;
+ label = "pm8550vs_c_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_D Channel nodes */
+ channel@303 {
+ reg = <ADC5_GEN3_DIE_TEMP(3)>;
+ label = "pm8550vs_d_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_E Channel nodes */
+ channel@403 {
+ reg = <ADC5_GEN3_DIE_TEMP(4)>;
+ label = "pm8550vs_e_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VE Channel nodes */
+ channel@503 {
+ reg = <ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ label = "pm8550ve_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_G Channel nodes */
+ channel@603 {
+ reg = <ADC5_GEN3_DIE_TEMP(6)>;
+ label = "pm8550vs_g_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550B Channel nodes */
+ channel@700 {
+ reg = <ADC5_GEN3_REF_GND(7)>;
+ label = "pm8550b_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@701 {
+ reg = <ADC5_GEN3_1P25VREF(7)>;
+ label = "pm8550b_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@703 {
+ reg = <ADC5_GEN3_DIE_TEMP(7)>;
+ label = "pm8550b_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@747 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+ label = "pm8550b_usb_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@749 {
+ reg = <ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+ label = "pm8550b_wls_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <15>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@78e {
+ reg = <ADC5_GEN3_VPH_PWR(7)>;
+ label = "pm8550b_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ channel@78f {
+ reg = <ADC5_GEN3_VBAT_SNS_QBG(7)>;
+ label = "pm8550b_vbat_sns_qbg";
+ qcom,pre-scaling = <1 6>;
+ };
+};
+
&pon_pwrkey {
status = "okay";
};
--
2.34.1
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH v6 3/5] arm64: dts: qcom: sm8550-hdk: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 ` [PATCH v6 3/5] arm64: dts: qcom: sm8550-hdk: " Neil Armstrong
@ 2026-07-21 15:37 ` Konrad Dybcio
0 siblings, 0 replies; 11+ messages in thread
From: Konrad Dybcio @ 2026-07-21 15:37 UTC (permalink / raw)
To: Neil Armstrong, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
On 7/21/26 5:31 PM, Neil Armstrong wrote:
> Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
> other PMICS on the system.
>
> The thermal nodes are sorted by the sensor channel to be
> coherent with the system thermal nodes ordering.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v6 4/5] arm64: dts: qcom: sm8650-qrd: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Neil Armstrong
` (2 preceding siblings ...)
2026-07-21 15:31 ` [PATCH v6 3/5] arm64: dts: qcom: sm8550-hdk: " Neil Armstrong
@ 2026-07-21 15:31 ` Neil Armstrong
2026-07-21 17:02 ` Konrad Dybcio
2026-07-21 15:31 ` [PATCH v6 5/5] arm64: dts: qcom: sm8650-hdk: " Neil Armstrong
2026-07-31 3:24 ` [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Bjorn Andersson
5 siblings, 1 reply; 11+ messages in thread
From: Neil Armstrong @ 2026-07-21 15:31 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Neil Armstrong
Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
other PMICS on the system.
The thermal nodes are sorted by the sensor channel to be
coherent with the system thermal nodes ordering.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8650-qrd.dts | 277 ++++++++++++++++++++++++++++++++
1 file changed, 277 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
index a28d70c85fa3..5709cfea1bfd 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-qrd.dts
@@ -158,6 +158,92 @@ platform {
};
};
+ thermal-zones {
+ skin-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ cam-flash-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wlan-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ pa-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ rear-tof-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ usb-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wls-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
vph_pwr: vph-pwr-regulator {
compatible = "regulator-fixed";
@@ -1039,27 +1125,218 @@ led@3 {
};
};
+&pm8550_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(1)>;
+ io-channel-names = "thermal";
+};
+
&pm8550b_eusb2_repeater {
vdd18-supply = <&vreg_l15b_1p8>;
vdd3-supply = <&vreg_l5b_3p1>;
};
+&pm8550b_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(7)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_c {
status = "okay";
};
+&pm8550vs_c_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(2)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_d {
status = "okay";
};
+&pm8550vs_d_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(3)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_e {
status = "okay";
};
+&pm8550vs_e_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(4)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_g {
status = "okay";
};
+&pm8550vs_g_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(6)>;
+ io-channel-names = "thermal";
+};
+
+&pm8550ve_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ io-channel-names = "thermal";
+};
+
+&pmk8550_vadc {
+ /* PM8550 Channel nodes */
+ channel@100 {
+ reg = <ADC5_GEN3_REF_GND(1)>;
+ label = "pm8550_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@101 {
+ reg = <ADC5_GEN3_1P25VREF(1)>;
+ label = "pm8550_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@103 {
+ reg = <ADC5_GEN3_DIE_TEMP(1)>;
+ label = "pm8550_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@144 {
+ reg = <ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+ label = "pm8550_msm_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@145 {
+ reg = <ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+ label = "pm8550_cam_flash_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@146 {
+ reg = <ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+ label = "pm8550_wlan_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@147 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+ label = "pm8550_pa_therm_1";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@148 {
+ reg = <ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+ label = "pm8550_rear_tof_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@18e {
+ reg = <ADC5_GEN3_VPH_PWR(1)>;
+ label = "pm8550_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ /* PM8550VS_C Channel nodes */
+ channel@203 {
+ reg = <ADC5_GEN3_DIE_TEMP(2)>;
+ label = "pm8550vs_c_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_D Channel nodes */
+ channel@303 {
+ reg = <ADC5_GEN3_DIE_TEMP(3)>;
+ label = "pm8550vs_d_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_E Channel nodes */
+ channel@403 {
+ reg = <ADC5_GEN3_DIE_TEMP(4)>;
+ label = "pm8550vs_e_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VE Channel nodes */
+ channel@503 {
+ reg = <ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ label = "pm8550ve_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_G Channel nodes */
+ channel@603 {
+ reg = <ADC5_GEN3_DIE_TEMP(6)>;
+ label = "pm8550vs_g_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550B Channel nodes */
+ channel@700 {
+ reg = <ADC5_GEN3_REF_GND(7)>;
+ label = "pm8550b_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@701 {
+ reg = <ADC5_GEN3_1P25VREF(7)>;
+ label = "pm8550b_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@703 {
+ reg = <ADC5_GEN3_DIE_TEMP(7)>;
+ label = "pm8550b_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@747 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+ label = "pm8550b_usb_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@749 {
+ reg = <ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+ label = "pm8550b_wls_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <15>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@78e {
+ reg = <ADC5_GEN3_VPH_PWR(7)>;
+ label = "pm8550b_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ channel@78f {
+ reg = <ADC5_GEN3_VBAT_SNS_QBG(7)>;
+ label = "pm8550b_vbat_sns_qbg";
+ qcom,pre-scaling = <1 6>;
+ };
+};
+
&qup_i2c3_data_clk {
/* Use internal I2C pull-up */
bias-pull-up = <2200>;
--
2.34.1
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH v6 4/5] arm64: dts: qcom: sm8650-qrd: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 ` [PATCH v6 4/5] arm64: dts: qcom: sm8650-qrd: " Neil Armstrong
@ 2026-07-21 17:02 ` Konrad Dybcio
0 siblings, 0 replies; 11+ messages in thread
From: Konrad Dybcio @ 2026-07-21 17:02 UTC (permalink / raw)
To: Neil Armstrong, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
On 7/21/26 5:31 PM, Neil Armstrong wrote:
> Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
> other PMICS on the system.
>
> The thermal nodes are sorted by the sensor channel to be
> coherent with the system thermal nodes ordering.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply [flat|nested] 11+ messages in thread
* [PATCH v6 5/5] arm64: dts: qcom: sm8650-hdk: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Neil Armstrong
` (3 preceding siblings ...)
2026-07-21 15:31 ` [PATCH v6 4/5] arm64: dts: qcom: sm8650-qrd: " Neil Armstrong
@ 2026-07-21 15:31 ` Neil Armstrong
2026-07-21 17:02 ` Konrad Dybcio
2026-07-31 3:24 ` [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Bjorn Andersson
5 siblings, 1 reply; 11+ messages in thread
From: Neil Armstrong @ 2026-07-21 15:31 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel, Neil Armstrong
Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
other PMICS on the system.
The thermal nodes are sorted by the sensor channel to be
coherent with the system thermal nodes ordering.
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
---
arch/arm64/boot/dts/qcom/sm8650-hdk.dts | 277 ++++++++++++++++++++++++++++++++
1 file changed, 277 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
index 80bd2437f154..71c0355ece4b 100644
--- a/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
+++ b/arch/arm64/boot/dts/qcom/sm8650-hdk.dts
@@ -220,6 +220,92 @@ platform {
};
};
+ thermal-zones {
+ skin-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ cam-flash-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wlan-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ pa-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ rear-tof-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ usb-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+
+ wls-thermal {
+ thermal-sensors = <&pmk8550_vadc ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+
+ trips {
+ trip-point0 {
+ temperature = <125000>;
+ hysteresis = <1000>;
+ type = "passive";
+ };
+ };
+ };
+ };
+
vph_pwr: regulator-vph-pwr {
compatible = "regulator-fixed";
@@ -1040,27 +1126,218 @@ led@3 {
};
};
+&pm8550_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(1)>;
+ io-channel-names = "thermal";
+};
+
&pm8550b_eusb2_repeater {
vdd18-supply = <&vreg_l15b_1p8>;
vdd3-supply = <&vreg_l5b_3p1>;
};
+&pm8550b_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(7)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_c {
status = "okay";
};
+&pm8550vs_c_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(2)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_d {
status = "okay";
};
+&pm8550vs_d_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(3)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_e {
status = "okay";
};
+&pm8550vs_e_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(4)>;
+ io-channel-names = "thermal";
+};
+
&pm8550vs_g {
status = "okay";
};
+&pm8550vs_g_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(6)>;
+ io-channel-names = "thermal";
+};
+
+&pm8550ve_temp_alarm {
+ io-channels = <&pmk8550_vadc ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ io-channel-names = "thermal";
+};
+
+&pmk8550_vadc {
+ /* PM8550 Channel nodes */
+ channel@100 {
+ reg = <ADC5_GEN3_REF_GND(1)>;
+ label = "pm8550_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@101 {
+ reg = <ADC5_GEN3_1P25VREF(1)>;
+ label = "pm8550_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@103 {
+ reg = <ADC5_GEN3_DIE_TEMP(1)>;
+ label = "pm8550_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@144 {
+ reg = <ADC5_GEN3_AMUX1_THM_100K_PU(1)>;
+ label = "pm8550_msm_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@145 {
+ reg = <ADC5_GEN3_AMUX2_THM_100K_PU(1)>;
+ label = "pm8550_cam_flash_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@146 {
+ reg = <ADC5_GEN3_AMUX3_THM_100K_PU(1)>;
+ label = "pm8550_wlan_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@147 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(1)>;
+ label = "pm8550_pa_therm_1";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@148 {
+ reg = <ADC5_GEN3_AMUX5_THM_100K_PU(1)>;
+ label = "pm8550_rear_tof_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@18e {
+ reg = <ADC5_GEN3_VPH_PWR(1)>;
+ label = "pm8550_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ /* PM8550VS_C Channel nodes */
+ channel@203 {
+ reg = <ADC5_GEN3_DIE_TEMP(2)>;
+ label = "pm8550vs_c_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_D Channel nodes */
+ channel@303 {
+ reg = <ADC5_GEN3_DIE_TEMP(3)>;
+ label = "pm8550vs_d_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_E Channel nodes */
+ channel@403 {
+ reg = <ADC5_GEN3_DIE_TEMP(4)>;
+ label = "pm8550vs_e_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VE Channel nodes */
+ channel@503 {
+ reg = <ADC5_GEN3_DIE_TEMP(PMK8550VE_SID)>;
+ label = "pm8550ve_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550VS_G Channel nodes */
+ channel@603 {
+ reg = <ADC5_GEN3_DIE_TEMP(6)>;
+ label = "pm8550vs_g_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ /* PM8550B Channel nodes */
+ channel@700 {
+ reg = <ADC5_GEN3_REF_GND(7)>;
+ label = "pm8550b_offset_ref";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@701 {
+ reg = <ADC5_GEN3_1P25VREF(7)>;
+ label = "pm8550b_vref_1p25";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@703 {
+ reg = <ADC5_GEN3_DIE_TEMP(7)>;
+ label = "pm8550b_die_temp";
+ qcom,pre-scaling = <1 1>;
+ };
+
+ channel@747 {
+ reg = <ADC5_GEN3_AMUX4_THM_100K_PU(7)>;
+ label = "pm8550b_usb_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <200>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@749 {
+ reg = <ADC5_GEN3_AMUX6_THM_100K_PU(7)>;
+ label = "pm8550b_wls_therm";
+ qcom,ratiometric;
+ qcom,hw-settle-time = <15>;
+ qcom,pre-scaling = <1 1>;
+ qcom,adc-tm;
+ };
+
+ channel@78e {
+ reg = <ADC5_GEN3_VPH_PWR(7)>;
+ label = "pm8550b_vph_pwr";
+ qcom,pre-scaling = <1 3>;
+ };
+
+ channel@78f {
+ reg = <ADC5_GEN3_VBAT_SNS_QBG(7)>;
+ label = "pm8550b_vbat_sns_qbg";
+ qcom,pre-scaling = <1 6>;
+ };
+};
+
&pon_pwrkey {
status = "okay";
};
--
2.34.1
^ permalink raw reply [flat|nested] 11+ messages in thread* Re: [PATCH v6 5/5] arm64: dts: qcom: sm8650-hdk: add SPMI ADC channels and thermal nodes
2026-07-21 15:31 ` [PATCH v6 5/5] arm64: dts: qcom: sm8650-hdk: " Neil Armstrong
@ 2026-07-21 17:02 ` Konrad Dybcio
0 siblings, 0 replies; 11+ messages in thread
From: Konrad Dybcio @ 2026-07-21 17:02 UTC (permalink / raw)
To: Neil Armstrong, Bjorn Andersson, Konrad Dybcio, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-arm-msm, devicetree, linux-kernel
On 7/21/26 5:31 PM, Neil Armstrong wrote:
> Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
> other PMICS on the system.
>
> The thermal nodes are sorted by the sensor channel to be
> coherent with the system thermal nodes ordering.
>
> Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
> ---
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Konrad
^ permalink raw reply [flat|nested] 11+ messages in thread
* Re: [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels
2026-07-21 15:31 [PATCH v6 0/5] arm64: dts: qcom: sm8[56]50: add PMIC5 Gen3 ADC channels Neil Armstrong
` (4 preceding siblings ...)
2026-07-21 15:31 ` [PATCH v6 5/5] arm64: dts: qcom: sm8650-hdk: " Neil Armstrong
@ 2026-07-31 3:24 ` Bjorn Andersson
5 siblings, 0 replies; 11+ messages in thread
From: Bjorn Andersson @ 2026-07-31 3:24 UTC (permalink / raw)
To: Konrad Dybcio, Rob Herring, Krzysztof Kozlowski, Conor Dooley,
Neil Armstrong
Cc: linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
On Tue, 21 Jul 2026 17:31:23 +0200, Neil Armstrong wrote:
> Now the bindings and driver was merged for the SPMI PMIC5 Gen3 ADC
> found on the PMK8550 which allow reading ADC data on the PMK8550
> and other PMICs on the system.
>
> Add the SPMI ADC channels on the PMK8550 SPMI5 ADC3 for the
> other PMICS on the system.
>
> [...]
Applied, thanks!
[1/5] arm64: dts: qcom: pmk8550: add VADC node
commit: da0343ba8c1f4275b1ce8127d5b6cee24d988868
[2/5] arm64: dts: qcom: sm8550-qrd: add SPMI ADC channels and thermal nodes
commit: c50667eab2d6482f6397c00735d429428e2b3c81
[3/5] arm64: dts: qcom: sm8550-hdk: add SPMI ADC channels and thermal nodes
commit: 972848c36912ec8cbe79d68e5b2875a889375ebf
[4/5] arm64: dts: qcom: sm8650-qrd: add SPMI ADC channels and thermal nodes
commit: b857a25ce399b9f49a2152d78d1a3893751e7cc4
[5/5] arm64: dts: qcom: sm8650-hdk: add SPMI ADC channels and thermal nodes
commit: 09d35331b7a94e30e30afb36b37a98513a2f60f7
Best regards,
--
Bjorn Andersson <andersson@kernel.org>
^ permalink raw reply [flat|nested] 11+ messages in thread