* [PATCH v2] mmc: sdhci-sprd: Wait until DLL locked after being configured
@ 2021-09-26 9:28 Chunyan Zhang
2021-09-27 5:48 ` Adrian Hunter
2021-09-27 22:32 ` Ulf Hansson
0 siblings, 2 replies; 3+ messages in thread
From: Chunyan Zhang @ 2021-09-26 9:28 UTC (permalink / raw)
To: Ulf Hansson, Adrian Hunter
Cc: linux-mmc, Baolin Wang, Orson Zhai, Chunyan Zhang, Chunyan Zhang,
zhenxiong.lai, yuelin.tang, LKML
From: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
According to the specification, DLL status has to be locked before using it.
Signed-off-by: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
---
Changes since v1:
* Use read_poll_timeout() instead of while loop.
---
drivers/mmc/host/sdhci-sprd.c | 13 +++++++++++++
1 file changed, 13 insertions(+)
diff --git a/drivers/mmc/host/sdhci-sprd.c b/drivers/mmc/host/sdhci-sprd.c
index 11e375579cfb..f33e9349e4e6 100644
--- a/drivers/mmc/host/sdhci-sprd.c
+++ b/drivers/mmc/host/sdhci-sprd.c
@@ -8,6 +8,7 @@
#include <linux/delay.h>
#include <linux/dma-mapping.h>
#include <linux/highmem.h>
+#include <linux/iopoll.h>
#include <linux/module.h>
#include <linux/of.h>
#include <linux/of_device.h>
@@ -39,6 +40,9 @@
#define SDHCI_SPRD_BIT_POSRD_DLY_INV BIT(21)
#define SDHCI_SPRD_BIT_NEGRD_DLY_INV BIT(29)
+#define SDHCI_SPRD_REG_32_DLL_STS0 0x210
+#define SDHCI_SPRD_DLL_LOCKED BIT(18)
+
#define SDHCI_SPRD_REG_32_BUSY_POSI 0x250
#define SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN BIT(25)
#define SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN BIT(24)
@@ -256,6 +260,15 @@ static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host)
sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
/* wait 1ms */
usleep_range(1000, 1250);
+
+ if (read_poll_timeout(sdhci_readl, tmp, (tmp & SDHCI_SPRD_DLL_LOCKED),
+ 2000, USEC_PER_SEC, false, host, SDHCI_SPRD_REG_32_DLL_STS0)) {
+ pr_err("%s: DLL locked fail!\n", mmc_hostname(host->mmc));
+ pr_info("%s: DLL_STS0 : 0x%x, DLL_CFG : 0x%x\n",
+ mmc_hostname(host->mmc),
+ sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_STS0),
+ sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG));
+ }
}
static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
--
2.25.1
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH v2] mmc: sdhci-sprd: Wait until DLL locked after being configured
2021-09-26 9:28 [PATCH v2] mmc: sdhci-sprd: Wait until DLL locked after being configured Chunyan Zhang
@ 2021-09-27 5:48 ` Adrian Hunter
2021-09-27 22:32 ` Ulf Hansson
1 sibling, 0 replies; 3+ messages in thread
From: Adrian Hunter @ 2021-09-27 5:48 UTC (permalink / raw)
To: Chunyan Zhang, Ulf Hansson
Cc: linux-mmc, Baolin Wang, Orson Zhai, Chunyan Zhang, zhenxiong.lai,
yuelin.tang, LKML
On 26/09/21 12:28 pm, Chunyan Zhang wrote:
> From: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
>
> According to the specification, DLL status has to be locked before using it.
>
> Signed-off-by: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Acked-by: Adrian Hunter <adrian.hunter@intel.com>
> ---
> Changes since v1:
> * Use read_poll_timeout() instead of while loop.
> ---
> drivers/mmc/host/sdhci-sprd.c | 13 +++++++++++++
> 1 file changed, 13 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-sprd.c b/drivers/mmc/host/sdhci-sprd.c
> index 11e375579cfb..f33e9349e4e6 100644
> --- a/drivers/mmc/host/sdhci-sprd.c
> +++ b/drivers/mmc/host/sdhci-sprd.c
> @@ -8,6 +8,7 @@
> #include <linux/delay.h>
> #include <linux/dma-mapping.h>
> #include <linux/highmem.h>
> +#include <linux/iopoll.h>
> #include <linux/module.h>
> #include <linux/of.h>
> #include <linux/of_device.h>
> @@ -39,6 +40,9 @@
> #define SDHCI_SPRD_BIT_POSRD_DLY_INV BIT(21)
> #define SDHCI_SPRD_BIT_NEGRD_DLY_INV BIT(29)
>
> +#define SDHCI_SPRD_REG_32_DLL_STS0 0x210
> +#define SDHCI_SPRD_DLL_LOCKED BIT(18)
> +
> #define SDHCI_SPRD_REG_32_BUSY_POSI 0x250
> #define SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN BIT(25)
> #define SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN BIT(24)
> @@ -256,6 +260,15 @@ static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host)
> sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
> /* wait 1ms */
> usleep_range(1000, 1250);
> +
> + if (read_poll_timeout(sdhci_readl, tmp, (tmp & SDHCI_SPRD_DLL_LOCKED),
> + 2000, USEC_PER_SEC, false, host, SDHCI_SPRD_REG_32_DLL_STS0)) {
> + pr_err("%s: DLL locked fail!\n", mmc_hostname(host->mmc));
> + pr_info("%s: DLL_STS0 : 0x%x, DLL_CFG : 0x%x\n",
> + mmc_hostname(host->mmc),
> + sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_STS0),
> + sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG));
> + }
> }
>
> static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
>
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH v2] mmc: sdhci-sprd: Wait until DLL locked after being configured
2021-09-26 9:28 [PATCH v2] mmc: sdhci-sprd: Wait until DLL locked after being configured Chunyan Zhang
2021-09-27 5:48 ` Adrian Hunter
@ 2021-09-27 22:32 ` Ulf Hansson
1 sibling, 0 replies; 3+ messages in thread
From: Ulf Hansson @ 2021-09-27 22:32 UTC (permalink / raw)
To: Chunyan Zhang
Cc: Adrian Hunter, linux-mmc, Baolin Wang, Orson Zhai, Chunyan Zhang,
zhenxiong.lai, yuelin.tang, LKML
On Sun, 26 Sept 2021 at 11:28, Chunyan Zhang <zhang.lyra@gmail.com> wrote:
>
> From: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
>
> According to the specification, DLL status has to be locked before using it.
>
> Signed-off-by: Zhenxiong Lai <zhenxiong.lai@unisoc.com>
> Signed-off-by: Chunyan Zhang <chunyan.zhang@unisoc.com>
Applied for next, thanks!
Kind regards
Uffe
> ---
> Changes since v1:
> * Use read_poll_timeout() instead of while loop.
> ---
> drivers/mmc/host/sdhci-sprd.c | 13 +++++++++++++
> 1 file changed, 13 insertions(+)
>
> diff --git a/drivers/mmc/host/sdhci-sprd.c b/drivers/mmc/host/sdhci-sprd.c
> index 11e375579cfb..f33e9349e4e6 100644
> --- a/drivers/mmc/host/sdhci-sprd.c
> +++ b/drivers/mmc/host/sdhci-sprd.c
> @@ -8,6 +8,7 @@
> #include <linux/delay.h>
> #include <linux/dma-mapping.h>
> #include <linux/highmem.h>
> +#include <linux/iopoll.h>
> #include <linux/module.h>
> #include <linux/of.h>
> #include <linux/of_device.h>
> @@ -39,6 +40,9 @@
> #define SDHCI_SPRD_BIT_POSRD_DLY_INV BIT(21)
> #define SDHCI_SPRD_BIT_NEGRD_DLY_INV BIT(29)
>
> +#define SDHCI_SPRD_REG_32_DLL_STS0 0x210
> +#define SDHCI_SPRD_DLL_LOCKED BIT(18)
> +
> #define SDHCI_SPRD_REG_32_BUSY_POSI 0x250
> #define SDHCI_SPRD_BIT_OUTR_CLK_AUTO_EN BIT(25)
> #define SDHCI_SPRD_BIT_INNR_CLK_AUTO_EN BIT(24)
> @@ -256,6 +260,15 @@ static void sdhci_sprd_enable_phy_dll(struct sdhci_host *host)
> sdhci_writel(host, tmp, SDHCI_SPRD_REG_32_DLL_CFG);
> /* wait 1ms */
> usleep_range(1000, 1250);
> +
> + if (read_poll_timeout(sdhci_readl, tmp, (tmp & SDHCI_SPRD_DLL_LOCKED),
> + 2000, USEC_PER_SEC, false, host, SDHCI_SPRD_REG_32_DLL_STS0)) {
> + pr_err("%s: DLL locked fail!\n", mmc_hostname(host->mmc));
> + pr_info("%s: DLL_STS0 : 0x%x, DLL_CFG : 0x%x\n",
> + mmc_hostname(host->mmc),
> + sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_STS0),
> + sdhci_readl(host, SDHCI_SPRD_REG_32_DLL_CFG));
> + }
> }
>
> static void sdhci_sprd_set_clock(struct sdhci_host *host, unsigned int clock)
> --
> 2.25.1
>
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2021-09-27 22:32 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2021-09-26 9:28 [PATCH v2] mmc: sdhci-sprd: Wait until DLL locked after being configured Chunyan Zhang
2021-09-27 5:48 ` Adrian Hunter
2021-09-27 22:32 ` Ulf Hansson
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®