[PATCH v10 00/10] io: accel: mma8452: Allow open drain interrupt pin configuration

[PATCH v10 00/10] io: accel: mma8452: Allow open drain interrupt pin configuration

[Esben Haabendal]

Extend the mma8452 driver with support for configuration of the
interrupt line in open-drain mode, which is needed for hardware designs
where the interrupt line is shared with other chips.

Adding drive-open-drain property to mma8452 device-tree node for such
designs to enable switching pin configuration to open-drain mode.

Signed-off-by: Esben Haabendal <esben@geanix.com>
---
Changes in v10:
- Fix sp3ling mistake in struct mma8452_data kernel-doc block.
- Swap ordering of pm_runtime and irq setup in mma8452_probe() to match the
  order now used in mma8452_remove().
- Bail out on -EINVAL in mma8452_interrupt() when CONFIG_PM is enabled.
- Link to v9: https://patch.msgid.link/20260916-mma8452-open-drain-v9-0-0dd24fa2f3d7@geanix.com

Changes in v9:
- Fix documentation of voltage regulator field(s) in struct mma8452_data
  kernel-doc block.
- Fix a couple of nitpicks in struct mma8452_data kernel-doc block.
- Switch to STANDBY mode before writing to CTRL_REG4.
- Add patch fixing runtime PM bugs in mma8452_read().
- Add comment about handling of -EINVAL return value from
  pm_runtime_get_if_active() in mma8452_interrupt().
- Fix for race between mma8452_remove() and mma8452_interrupt(), by calling
  free_irq() before pm_runtime_disable() instead of after.
- Fix mixing of guards and goto in mma8452_runtime_suspend(). Using guards
  will be re-introduced later on, when mixing can be avoided.
- Link to v8: https://patch.msgid.link/20260907-mma8452-open-drain-v8-0-c17407e22118@geanix.com

Changes in v8:
- Move patch 7 (with Fixes: ...) to go before the non-fixes patches.
- Rebased from v7.3-rc1 to current iio/togreg branch.
- Drop patch 8 (identical patch from Sanjay Chitroda already in togreg
  branch).
- Add new patch fixing a strangely extra indentation of a comment block.
- Add new patch adding documentation for struct mma8452_data.
- Move patch 4 to last in series, and rework the synchronization between
  suspend/resume and interrupt handler.
- Link to v7: https://patch.msgid.link/20260831-mma8452-open-drain-v7-0-22946812c928@geanix.com

Changes in v7:
- Use dev pointer directly in mma8452_runtime_suspend() also.
- Move struct i2c_client *client definition to patch 4.
- Drop patch 7 (Drop unneeded lock acquire on read).
- Link to v6: https://patch.msgid.link/20260825-mma8452-open-drain-v6-0-9b252804ee80@geanix.com

Changes in v6:
- Prevent interrupt storm if runtime suspend fails to set the device in
  standby mode by not setting suspended flag to true when failing to
  activate standby mode and by ensuring PM counter is not leaked in
  mma8452_interrupt().
- Don't acquire data->lock in mma8452_read_raw().
- Add fix for use-after-free in mma8452_probe() error path when CONFIG_PM
  is enabled.
- Fix (brown paper bug) build error introduced in v5.
- Renamed label in mma8452_interrupt().
- Add patch to return -ENODATA when missing device model information.
- Link to v5: https://patch.msgid.link/20260819-mma8452-open-drain-v5-0-d8aa590d7c36@geanix.com

Changes in v5:
- Squashed dev_err_probe() call to one line.
- Fixed typo in patch 2 title.
- Added synchronization between runtime suspend and interrupt handler.
- Link to v4: https://patch.msgid.link/20260812-mma8452-open-drain-v4-0-bfca15d02b59@geanix.com

Changes in v4:
- Fixed interrupt handler to check runtime PM status before trying to
  access the chip.
- Split open-drain support and interrupt sharing into separate patches.
- Added new patch to reuse existing struct device * through mma8452_probe()
  function.
- Print warning message when irq type is not set by firmware.
- Link to v3: https://patch.msgid.link/20260805-mma8452-open-drain-v3-0-6149f406a409@geanix.com

Changes in v3:
- Reordered patches, swapping #2 and #3.
- Always add IRQF_SHARED flag.
- New patch to change it so IQRF_TRIGGER_LOW flag is only added when no
  trigger type is set by firmware.
- Link to v2: https://patch.msgid.link/20260715-mma8452-open-drain-v2-0-95be9f5f4795@geanix.com

Changes in v2:
- Commit message of patch 2 updated.
- Operator precedence bug fixed in flags argument to
  request_threaded_irq().
- Always check return value of mma8452_set_interrupt_pin_mode(), and just
  check for non-zero value.
- Added new patch with optimization of struct mma8452_data ordering.
- Link to v1: https://patch.msgid.link/20260715-mma8452-open-drain-v1-0-b1dd2a440c60@geanix.com

To: Jonathan Cameron <jic23@kernel.org>
To: Lars-Peter Clausen <lars@metafoo.de>
To: Rob Herring <robh@kernel.org>
To: Krzysztof Kozlowski <krzk+dt@kernel.org>
To: Conor Dooley <conor+dt@kernel.org>
To: Martin Kepplinger <martink@posteo.de>
To: Sean Nyekjaer <sean@geanix.com>
To: David Lechner <dlechner@baylibre.com>
To: Nuno Sá <nuno.sa@analog.com>
To: Andy Shevchenko <andy@kernel.org>
To: Martin Kepplinger <martin.kepplinger@theobroma-systems.com>
To: Christoph Muellner <christoph.muellner@theobroma-systems.com>
Cc: linux-iio@vger.kernel.org
Cc: devicetree@vger.kernel.org
Cc: linux-kernel@vger.kernel.org

---
Esben Haabendal (10):
      dt-bindings: iio: accel: mma8452: Add drive-open-drain
      iio: accel: mma8452: Fix use-after-free bug in error error path
      iio: accel: mma8452: Fix runtime PM bugs in mma8452_read()
      iio: accel: mma8452: Optimize struct mma8452_data member orders
      iio: accel: mma8452: Only apply trigger type when not set by firmware
      iio: accel: mma8452: Fix unintended comment indent
      iio: accel: mma8452: Add comment block for struct mma8452_data
      iio: accel: mma8452: Allow open drain interrupt pin configuration
      iio: accel: mma8452: Use proper error code when missing device model
      iio: accel: mma8452: Support interrupt sharing

 .../devicetree/bindings/iio/accel/fsl,mma8452.yaml |   6 +
 drivers/iio/accel/mma8452.c                        | 217 ++++++++++++++++-----
 2 files changed, 177 insertions(+), 46 deletions(-)
---
base-commit: e5b9e42a20392b669097c8c4aa09c3aed82ba10c
change-id: 20250401-mma8452-open-drain-81577c41375c

Best regards,
--  
Esben Haabendal <esben@geanix.com>

[PATCH v10 01/10] dt-bindings: iio: accel: mma8452: Add drive-open-drain

[Esben Haabendal]

Add new boolean to configure selected interrupt pin to open drain instead
of the default push-pull mode.

Acked-by: Rob Herring (Arm) <robh@kernel.org>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml b/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml
index b0dd2b4e116a..20701aa725d0 100644
--- a/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml
+++ b/Documentation/devicetree/bindings/iio/accel/fsl,mma8452.yaml
@@ -39,6 +39,12 @@ properties:
     minItems: 1
     maxItems: 2
 
+  drive-open-drain:
+    $ref: /schemas/types.yaml#/definitions/flag
+    description: the interrupt line will be configured as open drain, which is
+      useful if several sensors share the same interrupt line. (This binding is
+      taken from pinctrl.)
+
   vdd-supply: true
   vddio-supply: true
 

-- 
2.55.0

[PATCH v10 02/10] iio: accel: mma8452: Fix use-after-free bug in error error path

[Esben Haabendal]

If mma8452_probe() fails in iio_device_register() or later, we could end up
with runtime suspend callback being called with a now freed device pointer.

Fixes: 96c0cb2bbfe0 ("iio: mma8452: add support for runtime power management")
Cc: stable@vger.kernel.org
Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 6 +++++-
 1 file changed, 5 insertions(+), 1 deletion(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index fe62a903f0e2..a937cbd84f30 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -1681,7 +1681,7 @@ static int mma8452_probe(struct i2c_client *client)
 
 	ret = iio_device_register(indio_dev);
 	if (ret < 0)
-		goto free_irq;
+		goto runtime_suspend;
 
 	ret = mma8452_set_freefall_mode(data, false);
 	if (ret < 0)
@@ -1692,6 +1692,10 @@ static int mma8452_probe(struct i2c_client *client)
 unregister_device:
 	iio_device_unregister(indio_dev);
 
+runtime_suspend:
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+
 free_irq:
 	if (client->irq)
 		free_irq(client->irq, indio_dev);

-- 
2.55.0

[PATCH v10 03/10] iio: accel: mma8452: Fix runtime PM bugs in mma8452_read()

[Esben Haabendal]

When runtime PM support was added [1], the implementation in mma8452_read()
was done incorrectly, as it calls mma8452_drdy() before ensuring runtime pm
has set the device active, so it can cause read from STATUS register while
device is suspended/off. At the same time, the return value from
i2c_smbus_read_i2c_block_data() was discarded, and the function would
return the value returned from pm_runtime_put_autosuspend() instead.

When the latter bug described above was fixed [2], another bug was
introduced, as mma8452_read() would now leak the runtime PM reference
counter when i2c_smbus_read_i2c_block_data() failed.

This commit corrects this mess.

[1] commit 96c0cb2bbfe0 ("iio: mma8452: add support for runtime power management")
[2] commit 5bdff291d20c ("iio: accel: mma8452: handle I2C read error(s) in mma8452_read()")

Fixes: 96c0cb2bbfe0 ("iio: mma8452: add support for runtime power management")
Cc: stable@vger.kernel.org
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 16 ++++++++++------
 1 file changed, 10 insertions(+), 6 deletions(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index a937cbd84f30..a77c4b88b61d 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -242,21 +242,25 @@ static int mma8452_set_runtime_pm_state(struct i2c_client *client, bool on)
 
 static int mma8452_read(struct mma8452_data *data, __be16 buf[3])
 {
-	int ret = mma8452_drdy(data);
-
-	if (ret < 0)
-		return ret;
+	int ret;
 
 	ret = mma8452_set_runtime_pm_state(data->client, true);
 	if (ret)
 		return ret;
 
+	ret = mma8452_drdy(data);
+	if (ret < 0)
+		goto out_runtime_put;
+
 	ret = i2c_smbus_read_i2c_block_data(data->client, MMA8452_OUT_X,
 					    3 * sizeof(__be16), (u8 *)buf);
 	if (ret < 0)
-		return ret;
+		goto out_runtime_put;
+
+	return mma8452_set_runtime_pm_state(data->client, false);
 
-	ret = mma8452_set_runtime_pm_state(data->client, false);
+out_runtime_put:
+	mma8452_set_runtime_pm_state(data->client, false);
 
 	return ret;
 }

-- 
2.55.0

[PATCH v10 04/10] iio: accel: mma8452: Optimize struct mma8452_data member orders

[Esben Haabendal]

Reorder struct mma8452_data members to avoid holes.

Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 7 ++++---
 1 file changed, 4 insertions(+), 3 deletions(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index a77c4b88b61d..8d70fe89110c 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -108,10 +108,7 @@ struct mma8452_data {
 	struct i2c_client *client;
 	struct mutex lock;
 	struct iio_mount_matrix orientation;
-	u8 ctrl_reg1;
-	u8 data_cfg;
 	const struct mma_chip_info *chip_info;
-	int sleep_val;
 	struct regulator_bulk_data regs[2];
 
 	/* Ensure correct alignment of time stamp when present */
@@ -119,6 +116,10 @@ struct mma8452_data {
 		__be16 channels[3];
 		aligned_s64 ts;
 	} buffer;
+
+	int sleep_val;
+	u8 ctrl_reg1;
+	u8 data_cfg;
 };
 
  /**

-- 
2.55.0

[PATCH v10 05/10] iio: accel: mma8452: Only apply trigger type when not set by firmware

[Esben Haabendal]

Instead of unconditionally overriding the trigger type, it is better to
only apply a default when no trigger type is set by firmware. This should
be reasonably backward compatible, and should only potentially cause
problems if systems exist where firmware specifies an incorrect trigger
type. With a bit of luck, there are no such systems.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 11 +++++++++--
 1 file changed, 9 insertions(+), 2 deletions(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 8d70fe89110c..72b4ab32775a 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -1669,9 +1669,16 @@ static int mma8452_probe(struct i2c_client *client)
 		goto trigger_cleanup;
 
 	if (client->irq) {
+		unsigned long irq_flags;
+
+		irq_flags = irq_get_trigger_type(client->irq);
+		if (irq_flags == IRQ_TYPE_NONE) {
+			dev_info(dev, "invalid irq type, setting default active low\n");
+			irq_flags = IRQF_TRIGGER_LOW;
+		}
+		irq_flags |= IRQF_ONESHOT;
 		ret = request_threaded_irq(client->irq, NULL, mma8452_interrupt,
-					   IRQF_TRIGGER_LOW | IRQF_ONESHOT,
-					   client->name, indio_dev);
+					   irq_flags, client->name, indio_dev);
 		if (ret)
 			goto buffer_cleanup;
 	}

-- 
2.55.0

[PATCH v10 06/10] iio: accel: mma8452: Fix unintended comment indent

[Esben Haabendal]

The extra space this block was indented with looks quite untraditional, and
does not align with the common style used in the kernel.

Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 30 +++++++++++++++---------------
 1 file changed, 15 insertions(+), 15 deletions(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 72b4ab32775a..b70bc8638128 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -122,21 +122,21 @@ struct mma8452_data {
 	u8 data_cfg;
 };
 
- /**
-  * struct mma8452_event_regs - chip specific data related to events
-  * @ev_cfg:			event config register address
-  * @ev_cfg_ele:			latch bit in event config register
-  * @ev_cfg_chan_shift:		number of the bit to enable events in X
-  *				direction; in event config register
-  * @ev_src:			event source register address
-  * @ev_ths:			event threshold register address
-  * @ev_ths_mask:		mask for the threshold value
-  * @ev_count:			event count (period) register address
-  *
-  * Since not all chips supported by the driver support comparing high pass
-  * filtered data for events (interrupts), different interrupt sources are
-  * used for different chips and the relevant registers are included here.
-  */
+/**
+ * struct mma8452_event_regs - chip specific data related to events
+ * @ev_cfg:			event config register address
+ * @ev_cfg_ele:			latch bit in event config register
+ * @ev_cfg_chan_shift:		number of the bit to enable events in X
+ *				direction; in event config register
+ * @ev_src:			event source register address
+ * @ev_ths:			event threshold register address
+ * @ev_ths_mask:		mask for the threshold value
+ * @ev_count:			event count (period) register address
+ *
+ * Since not all chips supported by the driver support comparing high pass
+ * filtered data for events (interrupts), different interrupt sources are
+ * used for different chips and the relevant registers are included here.
+ */
 struct mma8452_event_regs {
 	u8 ev_cfg;
 	u8 ev_cfg_ele;

-- 
2.55.0

[PATCH v10 07/10] iio: accel: mma8452: Add comment block for struct mma8452_data

[Esben Haabendal]

The struct mma8452_data is central for this driver, and it makes sense to
have a description of the fields in it to make it easier to work with the
driver.

Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index b70bc8638128..0c6ca6640f72 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -104,6 +104,21 @@
 
 #define MMA8452_AUTO_SUSPEND_DELAY_MS		2000
 
+/**
+ * struct mma8452_data - IIO device private data structure
+ * @client:			the I2C client object
+ * @lock:			mutex for synchronization of register
+ *				read-modify-write sequences and holding chip in
+ *				STANDBY mode while writing to registers
+ * @orientation:		mounting matrix, flipped axis etc.
+ * @chip_info:			chip specific data
+ * @regs:			reference to voltage regulators
+ * @buffer:			triggered buffer
+ * @sleep_val:			time in ms to sleep while waiting for drdy
+ * @ctrl_reg1:			CTRL_REG1 register shadow value
+ * @data_cfg:			DATA_CFG register shadow value
+ * @open_drain:			true for irq pin in open-drain mode
+ */
 struct mma8452_data {
 	struct i2c_client *client;
 	struct mutex lock;

-- 
2.55.0

[PATCH v10 08/10] iio: accel: mma8452: Allow open drain interrupt pin configuration

[Esben Haabendal]

When designing systems sharing the interrupt for mma8452 chips, it is
helpful to be able to configure the irq pin in open-drain mode (default is
push-pull).

Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 28 ++++++++++++++++++++++++++++
 1 file changed, 28 insertions(+)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 0c6ca6640f72..0b48aded2230 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -83,6 +83,8 @@
 #define  MMA8452_CTRL_REG2_RST			BIT(6)
 #define  MMA8452_CTRL_REG2_MODS_SHIFT		3
 #define  MMA8452_CTRL_REG2_MODS_MASK		0x1b
+#define MMA8452_CTRL_REG3			0x2c
+#define  MMA8452_CTRL_REG3_PP_OD		BIT(0)
 #define MMA8452_CTRL_REG4			0x2d
 #define MMA8452_CTRL_REG5			0x2e
 #define MMA8452_OFF_X				0x2f
@@ -135,6 +137,7 @@ struct mma8452_data {
 	int sleep_val;
 	u8 ctrl_reg1;
 	u8 data_cfg;
+	bool open_drain;
 };
 
 /**
@@ -662,6 +665,22 @@ static int mma8452_set_power_mode(struct mma8452_data *data, u8 mode)
 	return mma8452_change_config(data, MMA8452_CTRL_REG2, reg);
 }
 
+static int mma8452_set_interrupt_pin_mode(struct mma8452_data *data)
+{
+	int reg;
+
+	reg = i2c_smbus_read_byte_data(data->client, MMA8452_CTRL_REG3);
+	if (reg < 0)
+		return reg;
+
+	if (data->open_drain)
+		reg |= MMA8452_CTRL_REG3_PP_OD;
+	else
+		reg &= ~MMA8452_CTRL_REG3_PP_OD;
+
+	return i2c_smbus_write_byte_data(data->client, MMA8452_CTRL_REG3, reg);
+}
+
 /* returns >0 if in freefall mode, 0 if not or <0 if an error occurred */
 static int mma8452_freefall_mode_enabled(struct mma8452_data *data)
 {
@@ -1668,6 +1687,11 @@ static int mma8452_probe(struct i2c_client *client)
 			goto disable_regulators;
 	}
 
+	data->open_drain = device_property_read_bool(dev, "drive-open-drain");
+	ret = mma8452_set_interrupt_pin_mode(data);
+	if (ret)
+		goto trigger_cleanup;
+
 	data->ctrl_reg1 = MMA8452_CTRL_ACTIVE |
 			  (MMA8452_CTRL_DR_DEFAULT << MMA8452_CTRL_DR_SHIFT);
 
@@ -1795,6 +1819,10 @@ static int mma8452_runtime_resume(struct device *dev)
 		return ret;
 	}
 
+	ret = mma8452_set_interrupt_pin_mode(data);
+	if (ret)
+		goto runtime_resume_failed;
+
 	ret = mma8452_active(data);
 	if (ret < 0)
 		goto runtime_resume_failed;

-- 
2.55.0

[PATCH v10 09/10] iio: accel: mma8452: Use proper error code when missing device model

[Esben Haabendal]

Switch -ENODEV error on i2c_get_match_data() failure to -ENODATA to
satisfy the IIO coding style.

Reviewed-by: Joshua Crofts <joshua.crofts1@gmail.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@intel.com>
Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 2 +-
 1 file changed, 1 insertion(+), 1 deletion(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index 0b48aded2230..dc8031e14c29 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -1594,7 +1594,7 @@ static int mma8452_probe(struct i2c_client *client)
 
 	data->chip_info = i2c_get_match_data(client);
 	if (!data->chip_info)
-		return dev_err_probe(dev, -ENODEV, "unknown device model\n");
+		return dev_err_probe(dev, -ENODATA, "unknown device model\n");
 
 	ret = iio_read_mount_matrix(dev, &data->orientation);
 	if (ret)

-- 
2.55.0

[PATCH v10 10/10] iio: accel: mma8452: Support interrupt sharing

[Esben Haabendal]

Adding support for sharing interrupt line with other device requires the
interrupt handler to handle runtime PM suspension properly, ignoring the
irq if the device is suspended (maybe even off). And while at it, we use
the PM reference to ensure we do not get suspended while processing an irq.

In order to prevent the chip from raising irq while suspended (that is when
using fixed regulator, where suspend just means setting the device in
STANDBY mode), we disable all interrupt sources by clearing CTRL_REG4, and
then restores the value again when resuming.

The scoped_guard in mma8452_runtime_suspend() is changed to a plain
mutex_lock() instead, both to prevent mixing guards and goto, but also to
ensure that we stay in STANDBY mode while writing to CTRL_REG4 and all the
way up to disabling the device as much as possible.

With that in place, it is safe to add the IRQF_SHARED flag.

Keep in mind that the device by default is using push-pull for the irq pin,
which might require additional hardware design to allow interrupt sharing.

Signed-off-by: Esben Haabendal <esben@geanix.com>
---
 drivers/iio/accel/mma8452.c | 120 ++++++++++++++++++++++++++++++++++----------
 1 file changed, 93 insertions(+), 27 deletions(-)

diff --git a/drivers/iio/accel/mma8452.c b/drivers/iio/accel/mma8452.c
index dc8031e14c29..f05dd936b7f3 100644
--- a/drivers/iio/accel/mma8452.c
+++ b/drivers/iio/accel/mma8452.c
@@ -119,6 +119,7 @@
  * @sleep_val:			time in ms to sleep while waiting for drdy
  * @ctrl_reg1:			CTRL_REG1 register shadow value
  * @data_cfg:			DATA_CFG register shadow value
+ * @ctrl_reg4:			CTRL_REG4 register value to restore on resume
  * @open_drain:			true for irq pin in open-drain mode
  */
 struct mma8452_data {
@@ -137,6 +138,7 @@ struct mma8452_data {
 	int sleep_val;
 	u8 ctrl_reg1;
 	u8 data_cfg;
+	u8 ctrl_reg4;
 	bool open_drain;
 };
 
@@ -1086,15 +1088,32 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
 {
 	struct iio_dev *indio_dev = p;
 	struct mma8452_data *data = iio_priv(indio_dev);
+	struct device *dev = &data->client->dev;
 	irqreturn_t ret = IRQ_NONE;
+	int pm_status;
 	int src;
 
+	pm_status = pm_runtime_get_if_active(dev);
+	if (pm_status == 0)
+		/* device is powered down */
+		return IRQ_NONE;
+	if (IS_ENABLED(CONFIG_PM) && pm_status < 0)
+		/* runtime PM was disabled, possibly suspending */
+		return IRQ_HANDLED;
+
+	/*
+	 * pm_status is now 1 or -EINVAL (with CONFIG_PM not enabled). If
+	 * pm_status==1, runtime PM is enabled and device is RPM_ACTIVE. If
+	 * pm_status==-EINVAL, runtime PM is build-time disabled (i.e. CONFIG_PM
+	 * not enabled), and we can/must assume device is active.
+	 */
+
 	src = i2c_smbus_read_byte_data(data->client, MMA8452_INT_SRC);
 	if (src < 0)
-		return IRQ_NONE;
+		goto out_runtime_put;
 
 	if (!(src & (data->chip_info->enabled_events | MMA8452_INT_DRDY)))
-		return IRQ_NONE;
+		goto out_runtime_put;
 
 	if (src & MMA8452_INT_DRDY) {
 		iio_trigger_poll_nested(indio_dev->trig);
@@ -1120,6 +1139,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
 		ret = IRQ_HANDLED;
 	}
 
+out_runtime_put:
+	if (pm_status > 0)
+		pm_runtime_put_autosuspend(dev);
+
 	return ret;
 }
 
@@ -1707,6 +1730,14 @@ static int mma8452_probe(struct i2c_client *client)
 	if (ret < 0)
 		goto trigger_cleanup;
 
+	ret = pm_runtime_set_active(dev);
+	if (ret < 0)
+		goto buffer_cleanup;
+
+	pm_runtime_enable(dev);
+	pm_runtime_set_autosuspend_delay(dev, MMA8452_AUTO_SUSPEND_DELAY_MS);
+	pm_runtime_use_autosuspend(dev);
+
 	if (client->irq) {
 		unsigned long irq_flags;
 
@@ -1715,24 +1746,16 @@ static int mma8452_probe(struct i2c_client *client)
 			dev_info(dev, "invalid irq type, setting default active low\n");
 			irq_flags = IRQF_TRIGGER_LOW;
 		}
-		irq_flags |= IRQF_ONESHOT;
+		irq_flags |= IRQF_ONESHOT | IRQF_SHARED;
 		ret = request_threaded_irq(client->irq, NULL, mma8452_interrupt,
 					   irq_flags, client->name, indio_dev);
 		if (ret)
-			goto buffer_cleanup;
+			goto runtime_suspend;
 	}
 
-	ret = pm_runtime_set_active(dev);
-	if (ret < 0)
-		goto free_irq;
-
-	pm_runtime_enable(dev);
-	pm_runtime_set_autosuspend_delay(dev, MMA8452_AUTO_SUSPEND_DELAY_MS);
-	pm_runtime_use_autosuspend(dev);
-
 	ret = iio_device_register(indio_dev);
 	if (ret < 0)
-		goto runtime_suspend;
+		goto free_irq;
 
 	ret = mma8452_set_freefall_mode(data, false);
 	if (ret < 0)
@@ -1743,14 +1766,14 @@ static int mma8452_probe(struct i2c_client *client)
 unregister_device:
 	iio_device_unregister(indio_dev);
 
-runtime_suspend:
-	pm_runtime_disable(dev);
-	pm_runtime_set_suspended(dev);
-
 free_irq:
 	if (client->irq)
 		free_irq(client->irq, indio_dev);
 
+runtime_suspend:
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
+
 buffer_cleanup:
 	iio_triggered_buffer_cleanup(indio_dev);
 
@@ -1771,11 +1794,12 @@ static void mma8452_remove(struct i2c_client *client)
 
 	iio_device_unregister(indio_dev);
 
-	pm_runtime_disable(dev);
-	pm_runtime_set_suspended(dev);
-
 	if (client->irq)
 		free_irq(client->irq, indio_dev);
+	/* No irq will fire beyond this point */
+
+	pm_runtime_disable(dev);
+	pm_runtime_set_suspended(dev);
 
 	iio_triggered_buffer_cleanup(indio_dev);
 	mma8452_trigger_cleanup(indio_dev);
@@ -1787,29 +1811,67 @@ static void mma8452_remove(struct i2c_client *client)
 #ifdef CONFIG_PM
 static int mma8452_runtime_suspend(struct device *dev)
 {
-	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+	struct i2c_client *client = to_i2c_client(dev);
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 	struct mma8452_data *data = iio_priv(indio_dev);
 	int ret;
 
-	scoped_guard(mutex, &data->lock)
-		ret = mma8452_standby(data);
+	mutex_lock(&data->lock);
+
+	ret = mma8452_standby(data);
+	if (ret < 0) {
+		dev_err(dev, "transition to STANDBY mode failed\n");
+		ret = -EAGAIN;
+		goto out_unlock;
+	}
+
+	ret = i2c_smbus_read_byte_data(client, MMA8452_CTRL_REG4);
 	if (ret < 0) {
-		dev_err(dev, "powering off device failed\n");
-		return -EAGAIN;
+		dev_warn(dev, "backing up CTRL_REG4 failed\n");
+		ret = -EAGAIN;
+		goto out_active;
+	} else
+		data->ctrl_reg4 = ret;
+
+	ret = i2c_smbus_write_byte_data(client, MMA8452_CTRL_REG4, 0);
+	if (ret) {
+		dev_warn(dev, "disabling interrupt sources (CTRL_REG4) failed\n");
+		ret = -EAGAIN;
+		goto out_active;
 	}
 
+	/*
+	 * Interrupt line should be deasserted now, so we just need ensure any
+	 * mid-flight irq is completed (will return IRQ_NONE due to
+	 * pm_status==0).
+	 */
+	if (client->irq)
+		synchronize_irq(client->irq);
+
 	ret = regulator_bulk_disable(ARRAY_SIZE(data->regs), data->regs);
 	if (ret) {
 		dev_err(dev, "failed to disable regulators\n");
-		return ret;
+		goto out_restore_ctrl_reg4;
 	}
 
+	mutex_unlock(&data->lock);
 	return 0;
+
+out_restore_ctrl_reg4:
+	if (i2c_smbus_write_byte_data(client, MMA8452_CTRL_REG4, data->ctrl_reg4))
+		dev_warn(dev, "restoring CTRL_REG4 failed\n");
+out_active:
+	if (mma8452_active(data))
+		dev_warn(dev, "failed to switch back to ACTIVE mode\n");
+out_unlock:
+	mutex_unlock(&data->lock);
+	return ret;
 }
 
 static int mma8452_runtime_resume(struct device *dev)
 {
-	struct iio_dev *indio_dev = i2c_get_clientdata(to_i2c_client(dev));
+	struct i2c_client *client = to_i2c_client(dev);
+	struct iio_dev *indio_dev = i2c_get_clientdata(client);
 	struct mma8452_data *data = iio_priv(indio_dev);
 	int ret, sleep_val;
 
@@ -1823,6 +1885,10 @@ static int mma8452_runtime_resume(struct device *dev)
 	if (ret)
 		goto runtime_resume_failed;
 
+	ret = i2c_smbus_write_byte_data(client, MMA8452_CTRL_REG4, data->ctrl_reg4);
+	if (ret)
+		goto runtime_resume_failed;
+
 	ret = mma8452_active(data);
 	if (ret < 0)
 		goto runtime_resume_failed;

-- 
2.55.0

Re: [PATCH v10 10/10] iio: accel: mma8452: Support interrupt sharing

[Andy Shevchenko]

On Mon, Sep 28, 2026 at 10:26:26AM +0200, Esben Haabendal wrote:
> Adding support for sharing interrupt line with other device requires the
> interrupt handler to handle runtime PM suspension properly, ignoring the
> irq if the device is suspended (maybe even off). And while at it, we use
> the PM reference to ensure we do not get suspended while processing an irq.
> 
> In order to prevent the chip from raising irq while suspended (that is when
> using fixed regulator, where suspend just means setting the device in
> STANDBY mode), we disable all interrupt sources by clearing CTRL_REG4, and
> then restores the value again when resuming.
> 
> The scoped_guard in mma8452_runtime_suspend() is changed to a plain
> mutex_lock() instead, both to prevent mixing guards and goto, but also to
> ensure that we stay in STANDBY mode while writing to CTRL_REG4 and all the
> way up to disabling the device as much as possible.
> 
> With that in place, it is safe to add the IRQF_SHARED flag.
> 
> Keep in mind that the device by default is using push-pull for the irq pin,
> which might require additional hardware design to allow interrupt sharing.

...

> +	pm_status = pm_runtime_get_if_active(dev);
> +	if (pm_status == 0)
> +		/* device is powered down */
> +		return IRQ_NONE;

> +	if (IS_ENABLED(CONFIG_PM) && pm_status < 0)
> +		/* runtime PM was disabled, possibly suspending */
> +		return IRQ_HANDLED;

This is very interesting part. I bet this will be the first driver using this.
A big question "why?"

> +	/*
> +	 * pm_status is now 1 or -EINVAL (with CONFIG_PM not enabled). If
> +	 * pm_status==1, runtime PM is enabled and device is RPM_ACTIVE. If
> +	 * pm_status==-EINVAL, runtime PM is build-time disabled (i.e. CONFIG_PM
> +	 * not enabled), and we can/must assume device is active.
> +	 */
> +
>  	src = i2c_smbus_read_byte_data(data->client, MMA8452_INT_SRC);
>  	if (src < 0)
> -		return IRQ_NONE;
> +		goto out_runtime_put;
>  
>  	if (!(src & (data->chip_info->enabled_events | MMA8452_INT_DRDY)))
> -		return IRQ_NONE;
> +		goto out_runtime_put;
>  
>  	if (src & MMA8452_INT_DRDY) {
>  		iio_trigger_poll_nested(indio_dev->trig);
> @@ -1120,6 +1139,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
>  		ret = IRQ_HANDLED;
>  	}
>  
> +out_runtime_put:
> +	if (pm_status > 0)
> +		pm_runtime_put_autosuspend(dev);
> +
>  	return ret;
>  }

...

> +	pm_runtime_enable(dev);
> +	pm_runtime_set_autosuspend_delay(dev, MMA8452_AUTO_SUSPEND_DELAY_MS);
> +	pm_runtime_use_autosuspend(dev);

I don't see the respective _dont_use_autosuspend() call anywhere.

...

I am wondering how many of the above possible scenarios you were able to test.

...

P.S.  I bet you can now make a presentation "PM runtime in Linux and
why it is so hard."

-- 
With Best Regards,
Andy Shevchenko

Re: [PATCH v10 10/10] iio: accel: mma8452: Support interrupt sharing

[Esben Haabendal]

"Andy Shevchenko" <andriy.shevchenko@intel.com> writes:

> On Mon, Sep 28, 2026 at 10:26:26AM +0200, Esben Haabendal wrote:
>> Adding support for sharing interrupt line with other device requires the
>> interrupt handler to handle runtime PM suspension properly, ignoring the
>> irq if the device is suspended (maybe even off). And while at it, we use
>> the PM reference to ensure we do not get suspended while processing an irq.
>>
>> In order to prevent the chip from raising irq while suspended (that is when
>> using fixed regulator, where suspend just means setting the device in
>> STANDBY mode), we disable all interrupt sources by clearing CTRL_REG4, and
>> then restores the value again when resuming.
>>
>> The scoped_guard in mma8452_runtime_suspend() is changed to a plain
>> mutex_lock() instead, both to prevent mixing guards and goto, but also to
>> ensure that we stay in STANDBY mode while writing to CTRL_REG4 and all the
>> way up to disabling the device as much as possible.
>>
>> With that in place, it is safe to add the IRQF_SHARED flag.
>>
>> Keep in mind that the device by default is using push-pull for the irq pin,
>> which might require additional hardware design to allow interrupt sharing.
>
> ...
>
>> +	pm_status = pm_runtime_get_if_active(dev);
>> +	if (pm_status == 0)
>> +		/* device is powered down */
>> +		return IRQ_NONE;
>
>> +	if (IS_ENABLED(CONFIG_PM) && pm_status < 0)
>> +		/* runtime PM was disabled, possibly suspending */
>> +		return IRQ_HANDLED;
>
> This is very interesting part. I bet this will be the first driver using this.
> A big question "why?"

Because as I understood it, I needed to add this for the patch to be
accepted [1]. It is definitely possible that I have misunderstood that.

The technical reason I believe is that during system suspend,
pm_runtime_force_suspend() disabled runtime PM, and if a shared
interrupt durings this, pm_runtime_get_if_active returns -EINVAL, and we
could therefore end up doing I2C reads on unpowered hardware.

Per that reasoning, we probably should be doing this in other drivers as
well.

>> +	/*
>> +	 * pm_status is now 1 or -EINVAL (with CONFIG_PM not enabled). If
>> +	 * pm_status==1, runtime PM is enabled and device is RPM_ACTIVE. If
>> +	 * pm_status==-EINVAL, runtime PM is build-time disabled (i.e. CONFIG_PM
>> +	 * not enabled), and we can/must assume device is active.
>> +	 */
>> +
>>  	src = i2c_smbus_read_byte_data(data->client, MMA8452_INT_SRC);
>>  	if (src < 0)
>> -		return IRQ_NONE;
>> +		goto out_runtime_put;
>>
>>  	if (!(src & (data->chip_info->enabled_events | MMA8452_INT_DRDY)))
>> -		return IRQ_NONE;
>> +		goto out_runtime_put;
>>
>>  	if (src & MMA8452_INT_DRDY) {
>>  		iio_trigger_poll_nested(indio_dev->trig);
>> @@ -1120,6 +1139,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
>>  		ret = IRQ_HANDLED;
>>  	}
>>
>> +out_runtime_put:
>> +	if (pm_status > 0)
>> +		pm_runtime_put_autosuspend(dev);
>> +
>>  	return ret;
>>  }
>
> ...
>
>> +	pm_runtime_enable(dev);
>> +	pm_runtime_set_autosuspend_delay(dev, MMA8452_AUTO_SUSPEND_DELAY_MS);
>> +	pm_runtime_use_autosuspend(dev);
>
> I don't see the respective _dont_use_autosuspend() call anywhere.

Ah. I was not aware it was attached to a usage counter as well. I will
add a pm_runtime_dont_use_autosuspend() to the runtime_suspend: error handling.

> ...
>
> I am wondering how many of the above possible scenarios you were able
> to test.

Not enough. I haven't done any additional instrumentation to cause all
the various error conditions that is handled here in _probe().

> ...
>
> P.S.  I bet you can now make a presentation "PM runtime in Linux and
> why it is so hard."

LOL. I am getting there, yes. I have definitely learned a lot about how
runtime PM works. Especially since I was mostly starting from scratch on
that.

But i fear it would easily end up being quite a chaotic presentation :)

/Esben

Re: [PATCH v10 10/10] iio: accel: mma8452: Support interrupt sharing

[Esben Haabendal]

"Esben Haabendal" <esben@geanix.com> writes:

> "Andy Shevchenko" <andriy.shevchenko@intel.com> writes:
>
>> On Mon, Sep 28, 2026 at 10:26:26AM +0200, Esben Haabendal wrote:
>>> Adding support for sharing interrupt line with other device requires the
>>> interrupt handler to handle runtime PM suspension properly, ignoring the
>>> irq if the device is suspended (maybe even off). And while at it, we use
>>> the PM reference to ensure we do not get suspended while processing an irq.
>>>
>>> In order to prevent the chip from raising irq while suspended (that is when
>>> using fixed regulator, where suspend just means setting the device in
>>> STANDBY mode), we disable all interrupt sources by clearing CTRL_REG4, and
>>> then restores the value again when resuming.
>>>
>>> The scoped_guard in mma8452_runtime_suspend() is changed to a plain
>>> mutex_lock() instead, both to prevent mixing guards and goto, but also to
>>> ensure that we stay in STANDBY mode while writing to CTRL_REG4 and all the
>>> way up to disabling the device as much as possible.
>>>
>>> With that in place, it is safe to add the IRQF_SHARED flag.
>>>
>>> Keep in mind that the device by default is using push-pull for the irq pin,
>>> which might require additional hardware design to allow interrupt sharing.
>>
>> ...
>>
>>> +	pm_status = pm_runtime_get_if_active(dev);
>>> +	if (pm_status == 0)
>>> +		/* device is powered down */
>>> +		return IRQ_NONE;
>>
>>> +	if (IS_ENABLED(CONFIG_PM) && pm_status < 0)
>>> +		/* runtime PM was disabled, possibly suspending */
>>> +		return IRQ_HANDLED;
>>
>> This is very interesting part. I bet this will be the first driver using this.
>> A big question "why?"
>
> Because as I understood it, I needed to add this for the patch to be
> accepted [1]. It is definitely possible that I have misunderstood that.

Sorry, forgot to add the reference.

[1] https://lore.kernel.org/all/20260921015115.4c7d79f3@jic23-hlaptop/

>
> The technical reason I believe is that during system suspend,
> pm_runtime_force_suspend() disabled runtime PM, and if a shared
> interrupt durings this, pm_runtime_get_if_active returns -EINVAL, and we
> could therefore end up doing I2C reads on unpowered hardware.
>
> Per that reasoning, we probably should be doing this in other drivers as
> well.
>
>>> +	/*
>>> +	 * pm_status is now 1 or -EINVAL (with CONFIG_PM not enabled). If
>>> +	 * pm_status==1, runtime PM is enabled and device is RPM_ACTIVE. If
>>> +	 * pm_status==-EINVAL, runtime PM is build-time disabled (i.e. CONFIG_PM
>>> +	 * not enabled), and we can/must assume device is active.
>>> +	 */
>>> +
>>>  	src = i2c_smbus_read_byte_data(data->client, MMA8452_INT_SRC);
>>>  	if (src < 0)
>>> -		return IRQ_NONE;
>>> +		goto out_runtime_put;
>>>
>>>  	if (!(src & (data->chip_info->enabled_events | MMA8452_INT_DRDY)))
>>> -		return IRQ_NONE;
>>> +		goto out_runtime_put;
>>>
>>>  	if (src & MMA8452_INT_DRDY) {
>>>  		iio_trigger_poll_nested(indio_dev->trig);
>>> @@ -1120,6 +1139,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
>>>  		ret = IRQ_HANDLED;
>>>  	}
>>>
>>> +out_runtime_put:
>>> +	if (pm_status > 0)
>>> +		pm_runtime_put_autosuspend(dev);
>>> +
>>>  	return ret;
>>>  }
>>
>> ...
>>
>>> +	pm_runtime_enable(dev);
>>> +	pm_runtime_set_autosuspend_delay(dev, MMA8452_AUTO_SUSPEND_DELAY_MS);
>>> +	pm_runtime_use_autosuspend(dev);
>>
>> I don't see the respective _dont_use_autosuspend() call anywhere.
>
> Ah. I was not aware it was attached to a usage counter as well. I will
> add a pm_runtime_dont_use_autosuspend() to the runtime_suspend: error handling.
>
>> ...
>>
>> I am wondering how many of the above possible scenarios you were able
>> to test.
>
> Not enough. I haven't done any additional instrumentation to cause all
> the various error conditions that is handled here in _probe().
>
>> ...
>>
>> P.S.  I bet you can now make a presentation "PM runtime in Linux and
>> why it is so hard."
>
> LOL. I am getting there, yes. I have definitely learned a lot about how
> runtime PM works. Especially since I was mostly starting from scratch on
> that.
>
> But i fear it would easily end up being quite a chaotic presentation :)
>
> /Esben

Re: [PATCH v10 10/10] iio: accel: mma8452: Support interrupt sharing

[Joshua Crofts]

On Mon, 28 Sep 2026 12:26:12 +0300
Andy Shevchenko <andriy.shevchenko@intel.com> wrote:

> On Mon, Sep 28, 2026 at 10:26:26AM +0200, Esben Haabendal wrote:
> > Adding support for sharing interrupt line with other device requires the
> > interrupt handler to handle runtime PM suspension properly, ignoring the
> > irq if the device is suspended (maybe even off). And while at it, we use
> > the PM reference to ensure we do not get suspended while processing an irq.
> > 
> > In order to prevent the chip from raising irq while suspended (that is when
> > using fixed regulator, where suspend just means setting the device in
> > STANDBY mode), we disable all interrupt sources by clearing CTRL_REG4, and
> > then restores the value again when resuming.
> > 
> > The scoped_guard in mma8452_runtime_suspend() is changed to a plain
> > mutex_lock() instead, both to prevent mixing guards and goto, but also to
> > ensure that we stay in STANDBY mode while writing to CTRL_REG4 and all the
> > way up to disabling the device as much as possible.
> > 
> > With that in place, it is safe to add the IRQF_SHARED flag.
> > 
> > Keep in mind that the device by default is using push-pull for the irq pin,
> > which might require additional hardware design to allow interrupt sharing.  
> 
> ...
> 
> > +	pm_status = pm_runtime_get_if_active(dev);
> > +	if (pm_status == 0)
> > +		/* device is powered down */
> > +		return IRQ_NONE;  
> 
> > +	if (IS_ENABLED(CONFIG_PM) && pm_status < 0)
> > +		/* runtime PM was disabled, possibly suspending */
> > +		return IRQ_HANDLED;  
> 
> This is very interesting part. I bet this will be the first driver using this.
> A big question "why?"
> 
> > +	/*
> > +	 * pm_status is now 1 or -EINVAL (with CONFIG_PM not enabled). If
> > +	 * pm_status==1, runtime PM is enabled and device is RPM_ACTIVE. If
> > +	 * pm_status==-EINVAL, runtime PM is build-time disabled (i.e. CONFIG_PM
> > +	 * not enabled), and we can/must assume device is active.
> > +	 */
> > +
> >  	src = i2c_smbus_read_byte_data(data->client, MMA8452_INT_SRC);
> >  	if (src < 0)
> > -		return IRQ_NONE;
> > +		goto out_runtime_put;
> >  
> >  	if (!(src & (data->chip_info->enabled_events | MMA8452_INT_DRDY)))
> > -		return IRQ_NONE;
> > +		goto out_runtime_put;
> >  
> >  	if (src & MMA8452_INT_DRDY) {
> >  		iio_trigger_poll_nested(indio_dev->trig);
> > @@ -1120,6 +1139,10 @@ static irqreturn_t mma8452_interrupt(int irq, void *p)
> >  		ret = IRQ_HANDLED;
> >  	}
> >  
> > +out_runtime_put:
> > +	if (pm_status > 0)
> > +		pm_runtime_put_autosuspend(dev);
> > +
> >  	return ret;
> >  }  
> 
> ...
> 
> > +	pm_runtime_enable(dev);
> > +	pm_runtime_set_autosuspend_delay(dev, MMA8452_AUTO_SUSPEND_DELAY_MS);
> > +	pm_runtime_use_autosuspend(dev);  
> 
> I don't see the respective _dont_use_autosuspend() call anywhere.

FWIW, starting Linux 7.4 you won't need to add _dont_use_autosuspend()
calls, driver core will just handle it on unbind [1].

If anyone would like to join me in purging the kernel of redundant
dont_use_autosuspend() calls once the patch hits mainline, feel free
to do so :)

[1] https://lore.kernel.org/all/20260919-move-dont-use-autosuspend-v1-1-f6e2d1315c23@gmail.com/

-- 
Kind regards,
Joshua Crofts