From: Arkadiusz Miskiewicz <misiek@pld.ORG.PL>
To: linux-kernel@vger.kernel.org
Subject: Andre IDE patches + Promise, UDMA detection
Date: 17 Jan 2002 01:14:30 +0100 [thread overview]
Message-ID: <87n0zd25qx.fsf@arm.t19.ds.pwr.wroc.pl> (raw)
Hi,
I'm using 2.4.17 with ide.2.4.16.12102001.patch.bz2 + other
patches (listed here: http://cvs.pld.org.pl/SPECS/kernel.spec?rev=1.70.2.390)
on FIC LX based (quite old) mainboard + external PCI controller:
00:07.1 IDE interface: Intel Corp. 82371AB PIIX4 IDE (rev 01)
00:08.0 Unknown mass storage controller: Promise Technology, Inc. 20268 (rev 01)
My IDE setup is fully modular (well, whole kernel is):
xfs 479200 4 (autoclean)
xfs_support 6216 0 (autoclean) [xfs]
pagebuf 22112 4 (autoclean) [xfs xfs_support]
nls_iso8859-1 2880 1 (autoclean)
nls_cp437 4384 1 (autoclean)
vfat 9788 1 (autoclean)
fat 30680 0 (autoclean) [vfat]
sr_mod 13656 0 (autoclean) (unused)
scsi_mod 86776 1 (autoclean) [sr_mod]
ide-cd 27552 0
cdrom 28320 0 [sr_mod ide-cd]
ext3 58772 1 (autoclean)
ide-disk 9712 8 (autoclean)
ide-mod 153756 8 (autoclean) [ide-cd ide-disk]
jbd 34424 1 (autoclean) [ext3]
Kernel boots fine:
Linux version 2.4.17 (builder@kenny) (gcc version egcs-2.91.66 19990314/Linux (egcs-1.1.2 release)) #1 Tue Jan 15 13:19:47 UTC 2002
...
Freeing initrd memory: 174k freed
VFS: Mounted root (romfs filesystem) readonly.
Journalled Block Device driver loaded
Uniform Multi-Platform E-IDE driver Revision: 6.31
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
PIIX4: IDE controller on PCI bus 00 dev 39
PIIX4: chipset revision 1
PIIX4: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xf000-0xf007, BIOS settings: hda:pio, hdb:pio
ide1: BM-DMA at 0xf008-0xf00f, BIOS settings: hdc:pio, hdd:pio
PDC20268: IDE controller on PCI bus 00 dev 40
PCI: Found IRQ 11 for device 00:08.0
PDC20268: chipset revision 1
PDC20268: not 100% native mode: will probe irqs later
PDC20268: ROM enabled at 0xea000000
ide2: BM-DMA at 0xe400-0xe407, BIOS settings: hde:pio, hdf:pio
ide3: BM-DMA at 0xe408-0xe40f, BIOS settings: hdg:pio, hdh:pio
hda: ASUS CD-S500/A, ATAPI CD/DVD-ROM drive
hde: IBM-DTLA-307030, ATA DISK drive
hdf: IBM-DTLA-305040, ATA DISK drive
hdh: ST360021A, ATA DISK drive
ide0 at 0x1f0-0x1f7,0x3f6 on irq 14
ide2 at 0xd400-0xd407,0xd802 on irq 11
ide3 at 0xdc00-0xdc07,0xe002 on irq 11
hde: 60036480 sectors (30739 MB) w/1916KiB Cache, CHS=59560/16/63, UDMA(33)
hdf: 80418240 sectors (41174 MB) w/380KiB Cache, CHS=79780/16/63, UDMA(33)
hdh: 117231408 sectors (60022 MB) w/2048KiB Cache, CHS=116301/16/63, UDMA(33)
Partition check:
/dev/ide/host2/bus0/target0/lun0: p1 p2 p3 p4 < p5 p6 >
/dev/ide/host2/bus0/target1/lun0: p1 p2
/dev/ide/host2/bus1/target1/lun0: p1
kjournald starting. Commit interval 5 seconds
EXT3-fs: mounted filesystem with ordered data mode.
VFS: Mounted root (ext3 filesystem) readonly.
Unfortunately it thinks that all my harddrives (connected to promise
via 80wire cable) are UDMA33! Now _sometimes_ after boot it detects
these (properly) as UDMA100 and sometimes (seems more frequently)
as UDMA33.
Now when ide module detect my disk as UDMA33 and I have in my
initscripts hdparm (4.6) -X69 -c1 -d1 -m16 then some my processes
hang in D-state accessing hardrive (hdh for example).
Removing -X69 fixes that even if my kernel thinks that my drivers
are UDMA33 only...
So now it will be great to get ide module properly detecting UDMA.
--
Arkadiusz Miśkiewicz IPv6 ready PLD Linux at http://www.pld.org.pl
misiek(at)pld.org.pl AM2-6BONE, 1024/3DB19BBD, arekm(at)ircnet, PWr
next reply other threads:[~2002-01-17 0:15 UTC|newest]
Thread overview: 3+ messages / expand[flat|nested] mbox.gz Atom feed top
2002-01-17 0:14 Arkadiusz Miskiewicz [this message]
2002-01-17 0:26 ` Andre Hedrick
2002-01-17 8:31 ` Arkadiusz Miskiewicz
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=87n0zd25qx.fsf@arm.t19.ds.pwr.wroc.pl \
--to=misiek@pld.org.pl \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®