* [PATCH 2/2] arm64: dts: rockchip: rk3328: Add Orange Pi R1 Plus
2022-11-29 6:40 [PATCH 1/2] dt-bindings: Add doc for Orange Pi R1 Plus Chukun Pan
@ 2022-11-29 6:40 ` Chukun Pan
2022-11-29 7:53 ` Krzysztof Kozlowski
2022-11-29 7:52 ` [PATCH 1/2] dt-bindings: Add doc for " Krzysztof Kozlowski
1 sibling, 1 reply; 4+ messages in thread
From: Chukun Pan @ 2022-11-29 6:40 UTC (permalink / raw)
To: Heiko Stuebner
Cc: Rob Herring, Krzysztof Kozlowski, devicetree, linux-kernel,
linux-arm-kernel, linux-rockchip, Chukun Pan
Orange Pi R1 Plus is a Rockchip RK3328 based SBC by Xunlong.
This device is similar to the NanoPi R2S, and has a 16MB
SPI NOR (mx25l12805d). The reset button is changed to
directly reset the power supply, another detail is that
both network ports have independent MAC addresses.
Signed-off-by: Chukun Pan <amadeus@jmu.edu.cn>
---
arch/arm64/boot/dts/rockchip/Makefile | 1 +
.../dts/rockchip/rk3328-orangepi-r1-plus.dts | 373 ++++++++++++++++++
2 files changed, 374 insertions(+)
create mode 100644 arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
diff --git a/arch/arm64/boot/dts/rockchip/Makefile b/arch/arm64/boot/dts/rockchip/Makefile
index 0a76a2ebb5f6..27e00f4f3c86 100644
--- a/arch/arm64/boot/dts/rockchip/Makefile
+++ b/arch/arm64/boot/dts/rockchip/Makefile
@@ -15,6 +15,7 @@ dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3326-odroid-go3.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-a1.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-evb.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-nanopi-r2s.dtb
+dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-orangepi-r1-plus.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock64.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-rock-pi-e.dtb
dtb-$(CONFIG_ARCH_ROCKCHIP) += rk3328-roc-cc.dtb
diff --git a/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
new file mode 100644
index 000000000000..daa4da0bd5e4
--- /dev/null
+++ b/arch/arm64/boot/dts/rockchip/rk3328-orangepi-r1-plus.dts
@@ -0,0 +1,373 @@
+// SPDX-License-Identifier: (GPL-2.0+ OR MIT)
+/*
+ * Based on rk3328-nanopi-r2s.dts, which is:
+ * Copyright (c) 2020 David Bauer <mail@david-bauer.net>
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/leds/common.h>
+#include "rk3328.dtsi"
+
+/ {
+ model = "Xunlong Orange Pi R1 Plus";
+ compatible = "xunlong,orangepi-r1-plus", "rockchip,rk3328";
+
+ aliases {
+ ethernet1 = &rtl8153;
+ mmc0 = &sdmmc;
+ };
+
+ chosen {
+ stdout-path = "serial2:1500000n8";
+ };
+
+ gmac_clk: gmac-clock {
+ compatible = "fixed-clock";
+ clock-frequency = <125000000>;
+ clock-output-names = "gmac_clkin";
+ #clock-cells = <0>;
+ };
+
+ leds {
+ compatible = "gpio-leds";
+ pinctrl-0 = <&lan_led_pin>, <&sys_led_pin>, <&wan_led_pin>;
+ pinctrl-names = "default";
+
+ led-0 {
+ function = LED_FUNCTION_LAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio2 RK_PB7 GPIO_ACTIVE_HIGH>;
+ };
+
+ led-1 {
+ function = LED_FUNCTION_STATUS;
+ color = <LED_COLOR_ID_RED>;
+ gpios = <&gpio3 RK_PC5 GPIO_ACTIVE_HIGH>;
+ linux,default-trigger = "heartbeat";
+ };
+
+ led-2 {
+ function = LED_FUNCTION_WAN;
+ color = <LED_COLOR_ID_GREEN>;
+ gpios = <&gpio2 RK_PC2 GPIO_ACTIVE_HIGH>;
+ };
+ };
+
+ vcc_sd: sdmmc-regulator {
+ compatible = "regulator-fixed";
+ gpio = <&gpio0 RK_PD6 GPIO_ACTIVE_LOW>;
+ pinctrl-0 = <&sdmmc0m1_pin>;
+ pinctrl-names = "default";
+ regulator-name = "vcc_sd";
+ regulator-boot-on;
+ vin-supply = <&vcc_io>;
+ };
+
+ vcc_sys: vcc-sys {
+ compatible = "regulator-fixed";
+ regulator-name = "vcc_sys";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <5000000>;
+ regulator-max-microvolt = <5000000>;
+ };
+
+ vdd_5v_lan: vdd-5v-lan {
+ compatible = "regulator-fixed";
+ enable-active-high;
+ gpio = <&gpio2 RK_PC6 GPIO_ACTIVE_HIGH>;
+ pinctrl-0 = <&lan_vdd_pin>;
+ pinctrl-names = "default";
+ regulator-name = "vdd_5v_lan";
+ regulator-always-on;
+ regulator-boot-on;
+ vin-supply = <&vcc_sys>;
+ };
+};
+
+&cpu0 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu1 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu2 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&cpu3 {
+ cpu-supply = <&vdd_arm>;
+};
+
+&display_subsystem {
+ status = "disabled";
+};
+
+&gmac2io {
+ assigned-clocks = <&cru SCLK_MAC2IO>, <&cru SCLK_MAC2IO_EXT>;
+ assigned-clock-parents = <&gmac_clk>, <&gmac_clk>;
+ clock_in_out = "input";
+ phy-handle = <&rtl8211e>;
+ phy-mode = "rgmii";
+ phy-supply = <&vcc_io>;
+ pinctrl-0 = <&rgmiim1_pins>;
+ pinctrl-names = "default";
+ snps,aal;
+ rx_delay = <0x18>;
+ tx_delay = <0x24>;
+ status = "okay";
+
+ mdio {
+ compatible = "snps,dwmac-mdio";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ rtl8211e: ethernet-phy@1 {
+ reg = <1>;
+ pinctrl-0 = <ð_phy_reset_pin>;
+ pinctrl-names = "default";
+ reset-assert-us = <10000>;
+ reset-deassert-us = <50000>;
+ reset-gpios = <&gpio1 RK_PC2 GPIO_ACTIVE_LOW>;
+ };
+ };
+};
+
+&i2c1 {
+ status = "okay";
+
+ rk805: pmic@18 {
+ compatible = "rockchip,rk805";
+ reg = <0x18>;
+ interrupt-parent = <&gpio1>;
+ interrupts = <24 IRQ_TYPE_LEVEL_LOW>;
+ #clock-cells = <1>;
+ clock-output-names = "xin32k", "rk805-clkout2";
+ gpio-controller;
+ #gpio-cells = <2>;
+ pinctrl-0 = <&pmic_int_l>;
+ pinctrl-names = "default";
+ rockchip,system-power-controller;
+ wakeup-source;
+
+ vcc1-supply = <&vcc_sys>;
+ vcc2-supply = <&vcc_sys>;
+ vcc3-supply = <&vcc_sys>;
+ vcc4-supply = <&vcc_sys>;
+ vcc5-supply = <&vcc_io>;
+ vcc6-supply = <&vcc_sys>;
+
+ regulators {
+ vdd_log: DCDC_REG1 {
+ regulator-name = "vdd_log";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+
+ vdd_arm: DCDC_REG2 {
+ regulator-name = "vdd_arm";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <712500>;
+ regulator-max-microvolt = <1450000>;
+ regulator-ramp-delay = <12500>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <950000>;
+ };
+ };
+
+ vcc_ddr: DCDC_REG3 {
+ regulator-name = "vcc_ddr";
+ regulator-always-on;
+ regulator-boot-on;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ };
+ };
+
+ vcc_io: DCDC_REG4 {
+ regulator-name = "vcc_io";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <3300000>;
+ };
+ };
+
+ vcc_18: LDO_REG1 {
+ regulator-name = "vcc_18";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vcc18_emmc: LDO_REG2 {
+ regulator-name = "vcc18_emmc";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1800000>;
+ };
+ };
+
+ vdd_10: LDO_REG3 {
+ regulator-name = "vdd_10";
+ regulator-always-on;
+ regulator-boot-on;
+ regulator-min-microvolt = <1000000>;
+ regulator-max-microvolt = <1000000>;
+
+ regulator-state-mem {
+ regulator-on-in-suspend;
+ regulator-suspend-microvolt = <1000000>;
+ };
+ };
+ };
+ };
+};
+
+&io_domains {
+ pmuio-supply = <&vcc_io>;
+ vccio1-supply = <&vcc_io>;
+ vccio2-supply = <&vcc18_emmc>;
+ vccio3-supply = <&vcc_io>;
+ vccio4-supply = <&vcc_io>;
+ vccio5-supply = <&vcc_io>;
+ vccio6-supply = <&vcc_io>;
+ status = "okay";
+};
+
+&pinctrl {
+ gmac2io {
+ eth_phy_reset_pin: eth-phy-reset-pin {
+ rockchip,pins = <1 RK_PC2 RK_FUNC_GPIO &pcfg_pull_down>;
+ };
+ };
+
+ leds {
+ lan_led_pin: lan-led-pin {
+ rockchip,pins = <2 RK_PB7 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ sys_led_pin: sys-led-pin {
+ rockchip,pins = <3 RK_PC5 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+
+ wan_led_pin: wan-led-pin {
+ rockchip,pins = <2 RK_PC2 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ lan {
+ lan_vdd_pin: lan-vdd-pin {
+ rockchip,pins = <2 RK_PC6 RK_FUNC_GPIO &pcfg_pull_none>;
+ };
+ };
+
+ pmic {
+ pmic_int_l: pmic-int-l {
+ rockchip,pins = <1 RK_PD0 RK_FUNC_GPIO &pcfg_pull_up>;
+ };
+ };
+};
+
+&pwm2 {
+ status = "okay";
+};
+
+&sdmmc {
+ bus-width = <4>;
+ cap-sd-highspeed;
+ disable-wp;
+ pinctrl-0 = <&sdmmc0_clk>, <&sdmmc0_cmd>, <&sdmmc0_dectn>, <&sdmmc0_bus4>;
+ pinctrl-names = "default";
+ vmmc-supply = <&vcc_sd>;
+ status = "okay";
+};
+
+&spi0 {
+ status = "okay";
+
+ flash@0 {
+ compatible = "jedec,spi-nor";
+ reg = <0>;
+ spi-max-frequency = <50000000>;
+ };
+};
+
+&tsadc {
+ rockchip,hw-tshut-mode = <0>;
+ rockchip,hw-tshut-polarity = <0>;
+ status = "okay";
+};
+
+&u2phy {
+ status = "okay";
+};
+
+&u2phy_host {
+ status = "okay";
+};
+
+&u2phy_otg {
+ status = "okay";
+};
+
+&uart2 {
+ status = "okay";
+};
+
+&usb20_otg {
+ dr_mode = "host";
+ status = "okay";
+};
+
+&usbdrd3 {
+ dr_mode = "host";
+ status = "okay";
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ /* Second port is for USB 3.0 */
+ rtl8153: device@2 {
+ compatible = "usbbda,8153";
+ reg = <2>;
+ };
+};
+
+&usb_host0_ehci {
+ status = "okay";
+};
+
+&usb_host0_ohci {
+ status = "okay";
+};
--
2.25.1
^ permalink raw reply [flat|nested] 4+ messages in thread