Re: [PATCH v3,3/4] drm/mediatek: keep dsi as LP00 before dcs cmds transfer

[Rex-BC Chen <rex-bc.chen@mediatek.com>]

Hello Xinlei,

On Thu, 2022-03-17 at 15:53 +0800, xinlei.lee@mediatek.com wrote:
> From: Jitao Shi <jitao.shi@mediatek.com>
> 
> To comply with the panel sequence, hold the mipi signal to LP00 

Could you provide a example panel power sequence to let me understand
that?
Maybe you can put them in commit message.

> before the dcs cmds transmission,
> and pull the mipi signal high from LP00 to LP11 until the start of
> the dcs cmds transmission.

Maybe you can try to write as:
To comply with...
- Hold the mipi signal...
- Pul the miip signal high....

> If dsi is not in cmd mode, then dsi will pull the mipi signal high in
> the mtk_output_dsi_enable function.
> 
> Fixes: 2dd8075d2185 ("drm/mediatek: mtk_dsi: Use the drm_panel_bridge
> API")
> 

Can you remove this blank line?

> Signed-off-by: Jitao Shi <jitao.shi@mediatek.com>
> Signed-off-by: Xinlei Lee <xinlei.lee@mediatek.com>
> ---
>  drivers/gpu/drm/mediatek/mtk_dsi.c | 31 +++++++++++++++++++++++-----
> --
>  1 file changed, 24 insertions(+), 7 deletions(-)
> 
> diff --git a/drivers/gpu/drm/mediatek/mtk_dsi.c
> b/drivers/gpu/drm/mediatek/mtk_dsi.c
> index e33caaca11a7..b509d59235e2 100644
> --- a/drivers/gpu/drm/mediatek/mtk_dsi.c
> +++ b/drivers/gpu/drm/mediatek/mtk_dsi.c
> @@ -203,6 +203,7 @@ struct mtk_dsi {
>  	struct mtk_phy_timing phy_timing;
>  	int refcount;
>  	bool enabled;
> +	bool lanes_ready;
>  	u32 irq_data;
>  	wait_queue_head_t irq_wait_queue;
>  	const struct mtk_dsi_driver_data *driver_data;
> @@ -654,13 +655,6 @@ static int mtk_dsi_poweron(struct mtk_dsi *dsi)
>  	mtk_dsi_config_vdo_timing(dsi);
>  	mtk_dsi_set_interrupt_enable(dsi);
>  
> -	mtk_dsi_rxtx_control(dsi);
> -	usleep_range(30, 100);
> -	mtk_dsi_reset_dphy(dsi);
> -	mtk_dsi_clk_ulp_mode_leave(dsi);
> -	mtk_dsi_lane0_ulp_mode_leave(dsi);
> -	mtk_dsi_clk_hs_mode(dsi, 0);
> -
>  	return 0;
>  err_disable_engine_clk:
>  	clk_disable_unprepare(dsi->engine_clk);
> @@ -689,6 +683,8 @@ static void mtk_dsi_poweroff(struct mtk_dsi *dsi)
>  	clk_disable_unprepare(dsi->digital_clk);
>  
>  	phy_power_off(dsi->phy);
> +
> +	dsi->lanes_ready = false;
>  }
>  
>  static void mtk_output_dsi_enable(struct mtk_dsi *dsi)
> @@ -696,6 +692,16 @@ static void mtk_output_dsi_enable(struct mtk_dsi
> *dsi)
>  	if (dsi->enabled)
>  		return;
>  
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);
> +	}
> +
>  	mtk_dsi_set_mode(dsi);
>  	mtk_dsi_clk_hs_mode(dsi, 1);
>  
> @@ -995,6 +1001,17 @@ static ssize_t mtk_dsi_host_transfer(struct
> mipi_dsi_host *host,
>  	if (MTK_DSI_HOST_IS_READ(msg->type))
>  		irq_flag |= LPRX_RD_RDY_INT_FLAG;
>  
> +	if (!dsi->lanes_ready) {
> +		dsi->lanes_ready = true;
> +		mtk_dsi_rxtx_control(dsi);
> +		usleep_range(30, 100);
> +		mtk_dsi_reset_dphy(dsi);
> +		mtk_dsi_clk_ulp_mode_leave(dsi);
> +		mtk_dsi_lane0_ulp_mode_leave(dsi);
> +		mtk_dsi_clk_hs_mode(dsi, 0);

The drivers are the same with previous modification.
I think you can use a funtion for them?

> +		msleep(20);

Why delay 20ms but not in mtk_output_dsi_enable?

BRs,
Rex
> +	}
> +
>  	ret = mtk_dsi_host_send_cmd(dsi, msg, irq_flag);
>  	if (ret)
>  		goto restore_dsi_mode;