From: David Heidelberg <david@ixit.cz>
To: Frank Li <Frank.Li@oss.nxp.com>
Cc: Robert Foss <rfoss@kernel.org>, Todor Tomov <todor.too@gmail.com>,
Bryan O'Donoghue <bryan.odonoghue@linaro.org>,
Bryan O'Donoghue <bod@kernel.org>,
Vladimir Zapolskiy <vladimir.zapolskiy@linaro.org>,
Mauro Carvalho Chehab <mchehab@kernel.org>,
Luca Weiss <luca.weiss@fairphone.com>,
Petr Hodina <phodina@protonmail.com>,
"Dr. Git" <drgitx@gmail.com>, Cory Keitz <ckeitz@amazon.com>,
Loic Poulain <loic.poulain@oss.qualcomm.com>,
Frank Li <Frank.Li@nxp.com>,
Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>,
Kieran Bingham <kbingham@kernel.org>,
Sakari Ailus <sakari.ailus@linux.intel.com>,
linux-media@vger.kernel.org, linux-arm-msm@vger.kernel.org,
linux-kernel@vger.kernel.org, phone-devel@vger.kernel.org
Subject: Re: [PATCH v7 2/8] media: qcom: camss: csiphy-3ph: Use odd bits for configuring C-PHY lanes
Date: Mon, 8 Jun 2026 21:32:37 +0200 [thread overview]
Message-ID: <92b08f05-4b1a-4cf8-8616-d16bd4bb26ba@ixit.cz> (raw)
In-Reply-To: <aicG5nsTy7rIuWTc@lizhi-Precision-Tower-5810>
On 08/06/2026 20:16, Frank Li wrote:
> On Fri, Jun 05, 2026 at 03:14:40PM +0200, David Heidelberg wrote:
>> So far, only D-PHY mode was supported, which uses even bits when enabling
>> or masking lanes. For C-PHY configuration, the hardware instead requires
>> using the odd bits.
>>
>> Since there can be unrecognized configuration allow returning failure.
>>
>> Acked-by: Cory Keitz <ckeitz@amazon.com>
>> Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
>> Reviewed-by: Bryan O'Donoghue <bod@kernel.org>
>> Signed-off-by: David Heidelberg <david@ixit.cz>
>> ---
>> .../platform/qcom/camss/camss-csiphy-3ph-1-0.c | 39 +++++++++++++++++-----
>> 1 file changed, 31 insertions(+), 8 deletions(-)
>>
>> diff --git a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
>> index dac8d2ecf7995..fa24fc9706748 100644
>> --- a/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
>> +++ b/drivers/media/platform/qcom/camss/camss-csiphy-3ph-1-0.c
>> @@ -9,16 +9,17 @@
>> */
>>
>> #include "camss.h"
>> #include "camss-csiphy.h"
>>
>> #include <linux/delay.h>
>> #include <linux/interrupt.h>
>> #include <linux/io.h>
>> +#include <linux/media-bus-format.h>
>>
>> #define CSIPHY_3PH_LNn_CFG1(n) (0x000 + 0x100 * (n))
>> #define CSIPHY_3PH_LNn_CFG1_SWI_REC_DLY_PRG (BIT(7) | BIT(6))
>> #define CSIPHY_3PH_LNn_CFG2(n) (0x004 + 0x100 * (n))
>> #define CSIPHY_3PH_LNn_CFG2_LP_REC_EN_INT BIT(3)
>> #define CSIPHY_3PH_LNn_CFG3(n) (0x008 + 0x100 * (n))
>> #define CSIPHY_3PH_LNn_CFG4(n) (0x00c + 0x100 * (n))
>> #define CSIPHY_3PH_LNn_CFG4_T_HS_CLK_MISS 0xa4
>> @@ -1108,23 +1109,32 @@ static void csiphy_gen2_config_lanes(struct csiphy_device *csiphy,
>> writel_relaxed(val, csiphy->base + r->reg_addr);
>> if (r->delay_us)
>> udelay(r->delay_us);
>> }
>> }
>>
>> static u8 csiphy_get_lane_mask(struct csiphy_lanes_cfg *lane_cfg)
>> {
>> - u8 lane_mask;
>> - int i;
>> + u8 lane_mask = 0;
>> + u8 offset = 0;
>>
>> - lane_mask = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE;
>> + switch (lane_cfg->phy_cfg) {
>> + case V4L2_MBUS_CSI2_CPHY:
>> + offset = 1;
>> + break;
>> + case V4L2_MBUS_CSI2_DPHY:
>> + lane_mask = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE;
>> + break;
>> + default:
>> + break;
>> + }
>>
>> - for (i = 0; i < lane_cfg->num_data; i++)
>> - lane_mask |= 1 << lane_cfg->data[i].pos;
>> + for (int i = 0; i < lane_cfg->num_data; i++)
>> + lane_mask |= BIT(lane_cfg->data[i].pos + offset);
>>
>> return lane_mask;
>> }
>>
>> static bool csiphy_is_gen2(u32 version)
>> {
>> bool ret = false;
>>
>> @@ -1155,19 +1165,32 @@ static void csiphy_lanes_enable(struct csiphy_device *csiphy,
>> struct csiphy_lanes_cfg *c = &cfg->csi2->lane_cfg;
>> struct csiphy_device_regs *regs = csiphy->regs;
>> u8 settle_cnt;
>> u8 val;
>> int i;
>>
>> settle_cnt = csiphy_settle_cnt_calc(link_freq, csiphy->timer_clk_rate);
>>
>> - val = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE;
>> - for (i = 0; i < c->num_data; i++)
>> - val |= BIT(c->data[i].pos * 2);
>> + val = 0;
>> +
>> + switch (c->phy_cfg) {
>> + case V4L2_MBUS_CSI2_CPHY:
>> + for (i = 0; i < c->num_data; i++)
>> + val |= BIT((c->data[i].pos * 2) + 1);
>> + break;
>> + case V4L2_MBUS_CSI2_DPHY:
>> + val = CSIPHY_3PH_CMN_CSI_COMMON_CTRL5_CLK_ENABLE;
>> +
>> + for (i = 0; i < c->num_data; i++)
>> + val |= BIT(c->data[i].pos * 2);
>> + break;
>> + default:
>> + WARN_ONCE(1, "Unsupported bus type %d!\n", c->phy_cfg);
>> + }
>
> can you use similar method as csiphy_get_lane_mask()
>
Done, look better, but I guess we seriously need the refactor/split done by
Bryan as I looking at the current code.
David
> Frank
>>
>> writel_relaxed(val, csiphy->base +
>> CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 5));
>>
>> val = CSIPHY_3PH_CMN_CSI_COMMON_CTRL6_COMMON_PWRDN_B;
>> writel_relaxed(val, csiphy->base +
>> CSIPHY_3PH_CMN_CSI_COMMON_CTRLn(regs->offset, 6));
>>
>>
>> --
>> 2.53.0
>>
--
David Heidelberg
next prev parent reply other threads:[~2026-06-08 19:32 UTC|newest]
Thread overview: 19+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-06-05 13:14 [PATCH v7 0/8] media: camss: Add support for C-PHY configuration on Qualcomm platforms David Heidelberg via B4 Relay
2026-06-05 13:14 ` [PATCH v7 1/8] media: qcom: camss: csiphy: Introduce PHY configuration David Heidelberg via B4 Relay
2026-06-05 13:14 ` [PATCH v7 2/8] media: qcom: camss: csiphy-3ph: Use odd bits for configuring C-PHY lanes David Heidelberg via B4 Relay
2026-06-08 18:16 ` Frank Li
2026-06-08 19:32 ` David Heidelberg [this message]
2026-06-09 9:59 ` Nihal Kumar Gupta
2026-06-10 8:18 ` Wenmeng Liu
2026-06-05 13:14 ` [PATCH v7 3/8] media: qcom: camss: Prepare CSID for C-PHY support David Heidelberg via B4 Relay
2026-06-08 18:18 ` Frank Li
2026-06-05 13:14 ` [PATCH v7 4/8] media: qcom: camss: Initialize lanes after lane configuration is available David Heidelberg via B4 Relay
2026-06-05 13:14 ` [PATCH v7 5/8] media: qcom: camss: csiphy-3ph: Add Gen2 v1.1 MIPI CSI-2 C-PHY init David Heidelberg via B4 Relay
2026-06-08 9:00 ` Bryan O'Donoghue
2026-06-08 10:37 ` David Heidelberg
2026-06-05 13:14 ` [PATCH v7 6/8] media: qcom: camss: csiphy-3ph: Update " David Heidelberg via B4 Relay
2026-06-05 13:14 ` [PATCH v7 7/8] media: qcom: camss: Account for C-PHY when calculating link frequency David Heidelberg via B4 Relay
2026-06-10 8:23 ` Wenmeng Liu
2026-06-10 17:44 ` David Heidelberg
2026-06-05 13:14 ` [PATCH v7 8/8] media: qcom: camss: Enable C-PHY where available David Heidelberg via B4 Relay
2026-06-08 8:56 ` [PATCH v7 0/8] media: camss: Add support for C-PHY configuration on Qualcomm platforms Bryan O'Donoghue
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=92b08f05-4b1a-4cf8-8616-d16bd4bb26ba@ixit.cz \
--to=david@ixit.cz \
--cc=Frank.Li@nxp.com \
--cc=Frank.Li@oss.nxp.com \
--cc=bod@kernel.org \
--cc=bryan.odonoghue@linaro.org \
--cc=ckeitz@amazon.com \
--cc=drgitx@gmail.com \
--cc=kbingham@kernel.org \
--cc=konrad.dybcio@oss.qualcomm.com \
--cc=linux-arm-msm@vger.kernel.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-media@vger.kernel.org \
--cc=loic.poulain@oss.qualcomm.com \
--cc=luca.weiss@fairphone.com \
--cc=mchehab@kernel.org \
--cc=phodina@protonmail.com \
--cc=phone-devel@vger.kernel.org \
--cc=rfoss@kernel.org \
--cc=sakari.ailus@linux.intel.com \
--cc=todor.too@gmail.com \
--cc=vladimir.zapolskiy@linaro.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®