* [PATCH 1/3] arm64: dts: qcom: x1e80100-romulus: Configure audio
2024-11-22 2:14 [PATCH 0/3] More Surface Laptop 7 features Konrad Dybcio
@ 2024-11-22 2:14 ` Konrad Dybcio
2024-11-22 2:14 ` [PATCH 2/3] arm64: dts: qcom: x1e80100-romulus: Set up PCIe3 / SDCard reader Konrad Dybcio
2024-11-22 2:14 ` [PATCH 3/3] arm64: dts: qcom: x1e80100-romulus: Set up PS8830s Konrad Dybcio
2 siblings, 0 replies; 7+ messages in thread
From: Konrad Dybcio @ 2024-11-22 2:14 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Marijn Suijten, linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
The Laptop 7 features a single pair of speakers and an equal amount of
digital mics.
Add the required nodes to support audio playback and recording.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
.../boot/dts/qcom/x1e80100-microsoft-romulus.dtsi | 187 +++++++++++++++++++++
1 file changed, 187 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
index 6835fdeef3aec10206e8b2839d23e4f3494afe1e..6aea8f3573e834273d56448da772edd27855efec 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
@@ -22,6 +22,33 @@ aliases {
i2c7 = &i2c7;
};
+ wcd938x: audio-codec {
+ compatible = "qcom,wcd9385-codec";
+
+ reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+ qcom,micbias1-microvolt = <1800000>;
+ qcom,micbias2-microvolt = <1800000>;
+ qcom,micbias3-microvolt = <1800000>;
+ qcom,micbias4-microvolt = <1800000>;
+ qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+ qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+ qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+ qcom,rx-device = <&wcd_rx>;
+ qcom,tx-device = <&wcd_tx>;
+
+
+ vdd-buck-supply = <&vreg_l15b>;
+ vdd-rxtx-supply = <&vreg_l15b>;
+ vdd-io-supply = <&vreg_l15b>;
+ vdd-mic-bias-supply = <&vreg_bob1>;
+
+ pinctrl-0 = <&wcd_default>;
+ pinctrl-names = "default";
+
+ #sound-dai-cells = <1>;
+ };
+
backlight: backlight {
compatible = "pwm-backlight";
pwms = <&pmk8550_pwm 0 5000000>;
@@ -184,6 +211,86 @@ vph_pwr: regulator-vph-pwr {
regulator-always-on;
regulator-boot-on;
};
+
+ sound {
+ compatible = "qcom,x1e80100-sndcard";
+ model = "X1E80100-Romulus";
+ audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+ "SpkrRight IN", "WSA WSA_SPK2 OUT",
+ "IN1_HPHL", "HPHL_OUT",
+ "IN2_HPHR", "HPHR_OUT",
+ "AMIC2", "MIC BIAS2",
+ "VA DMIC0", "MIC BIAS3",
+ "VA DMIC1", "MIC BIAS3",
+ "VA DMIC0", "VA MIC BIAS3",
+ "VA DMIC1", "VA MIC BIAS3",
+ "TX SWR_INPUT1", "ADC2_OUTPUT";
+
+ wcd-playback-dai-link {
+ link-name = "WCD Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wcd-capture-dai-link {
+ link-name = "WCD Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+ };
+
+ codec {
+ sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ wsa-dai-link {
+ link-name = "WSA Playback";
+
+ cpu {
+ sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+ };
+
+ codec {
+ sound-dai = <&left_spkr>, <&right_spkr>,
+ <&swr0 0>, <&lpass_wsamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+
+ va-dai-link {
+ link-name = "VA Capture";
+
+ cpu {
+ sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+ };
+
+ codec {
+ sound-dai = <&lpass_vamacro 0>;
+ };
+
+ platform {
+ sound-dai = <&q6apm>;
+ };
+ };
+ };
};
&apps_rsc {
@@ -595,6 +702,25 @@ &i2c7 {
/* PS8830 USB retimer @8 */
};
+&lpass_tlmm {
+ spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+ pins = "gpio12";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+};
+
+&lpass_vamacro {
+ qcom,dmic-sample-rate = <4800000>;
+
+ vdd-micb-supply = <&vreg_l1b>;
+
+ pinctrl-0 = <&dmic01_default>;
+ pinctrl-names = "default";
+};
+
&mdss {
status = "okay";
};
@@ -737,6 +863,59 @@ &smb2360_2_eusb2_repeater {
vdd3-supply = <&vreg_l8b>;
};
+&swr0 {
+ pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+ pinctrl-names = "default";
+
+ status = "okay";
+
+ /* WSA8845, Left speaker */
+ left_spkr: speaker@0,0 {
+ compatible = "sdw20217020400";
+ reg = <0 0>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrLeft";
+ vdd-1p8-supply = <&vreg_l15b>;
+ vdd-io-supply = <&vreg_l12b>;
+ qcom,port-mapping = <1 2 3 7 10 13>;
+ };
+
+ /* WSA8845, Right speaker */
+ right_spkr: speaker@0,1 {
+ compatible = "sdw20217020400";
+ reg = <0 1>;
+ reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+ #sound-dai-cells = <0>;
+ sound-name-prefix = "SpkrRight";
+ vdd-1p8-supply = <&vreg_l15b>;
+ vdd-io-supply = <&vreg_l12b>;
+ qcom,port-mapping = <4 5 6 7 11 13>;
+ };
+};
+
+&swr1 {
+ status = "okay";
+
+ /* WCD9385 RX */
+ wcd_rx: codec@0,4 {
+ compatible = "sdw20217010d00";
+ reg = <0 4>;
+ qcom,rx-port-mapping = <1 2 3 4 5>;
+ };
+};
+
+&swr2 {
+ status = "okay";
+
+ /* WCD9385 TX */
+ wcd_tx: codec@0,3 {
+ compatible = "sdw20217010d00";
+ reg = <0 3>;
+ qcom,tx-port-mapping = <2 2 3 4>;
+ };
+};
+
&tlmm {
gpio-reserved-ranges = <44 4>, /* SPI (TPM) */
<238 1>; /* UFS Reset */
@@ -790,6 +969,14 @@ wake-n-pins {
};
};
+ wcd_default: wcd-reset-n-active-state {
+ pins = "gpio191";
+ function = "gpio";
+ drive-strength = <16>;
+ bias-disable;
+ output-low;
+ };
+
cam_indicator_en: cam-indicator-en-state {
pins = "gpio225";
function = "gpio";
--
2.47.0
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH 2/3] arm64: dts: qcom: x1e80100-romulus: Set up PCIe3 / SDCard reader
2024-11-22 2:14 [PATCH 0/3] More Surface Laptop 7 features Konrad Dybcio
2024-11-22 2:14 ` [PATCH 1/3] arm64: dts: qcom: x1e80100-romulus: Configure audio Konrad Dybcio
@ 2024-11-22 2:14 ` Konrad Dybcio
2024-11-22 9:27 ` Dmitry Baryshkov
2024-11-22 2:14 ` [PATCH 3/3] arm64: dts: qcom: x1e80100-romulus: Set up PS8830s Konrad Dybcio
2 siblings, 1 reply; 7+ messages in thread
From: Konrad Dybcio @ 2024-11-22 2:14 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Marijn Suijten, linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
The Surface Laptops have a Realtek RTS5261 SD Card reader connected
over a Gen1x1 link to the PCIe3 host. Set up the necessary bits to
make it functional.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
.../boot/dts/qcom/x1e80100-microsoft-romulus.dtsi | 63 ++++++++++++++++++++++
1 file changed, 63 insertions(+)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
index 6aea8f3573e834273d56448da772edd27855efec..66a12b20b096baa7d5cf8c5fb65927b765aa18ff 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
@@ -767,6 +767,27 @@ &mdss_dp3_phy {
status = "okay";
};
+&pcie3 {
+ perst-gpios = <&tlmm 143 GPIO_ACTIVE_LOW>;
+ wake-gpios = <&tlmm 145 GPIO_ACTIVE_HIGH>;
+
+ /* The power supply enable GPIOs are reserved by the secure firmware */
+
+ pinctrl-0 = <&pcie3_default>;
+ pinctrl-names = "default";
+
+ /* The RTS5261 chip on the other side only does Gen1x1 anyway */
+ max-link-speed = <1>;
+ status = "okay";
+};
+
+&pcie3_phy {
+ vdda-phy-supply = <&vreg_l3c>;
+ vdda-pll-supply = <&vreg_l3e>;
+
+ status = "okay";
+};
+
&pcie4 {
status = "okay";
};
@@ -797,6 +818,25 @@ &pcie6a_phy {
status = "okay";
};
+&pm8550ve_2_gpios {
+ sde7_main_reg_en: sde7-main-reg-en-state {
+ pins = "gpio6";
+ function = "normal";
+ };
+
+ sde7_aux_reg_en: sde7-aux-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ };
+};
+
+&pm8550ve_8_gpios {
+ vreg_12v_x8_en: 12v-x8-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ };
+};
+
&pmc8380_3_gpios {
edp_bl_en: edp-bl-en-state {
pins = "gpio4";
@@ -946,6 +986,29 @@ ssam_state: ssam-state-state {
bias-disable;
};
+ pcie3_default: pcie3-default-state {
+ perst-n-pins {
+ pins = "gpio143";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ clkreq-n-pins {
+ pins = "gpio144";
+ function = "pcie3_clk";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+
+ wake-n-pins {
+ pins = "gpio145";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-pull-up;
+ };
+ };
+
pcie6a_default: pcie6a-default-state {
perst-n-pins {
pins = "gpio152";
--
2.47.0
^ permalink raw reply [flat|nested] 7+ messages in thread* [PATCH 3/3] arm64: dts: qcom: x1e80100-romulus: Set up PS8830s
2024-11-22 2:14 [PATCH 0/3] More Surface Laptop 7 features Konrad Dybcio
2024-11-22 2:14 ` [PATCH 1/3] arm64: dts: qcom: x1e80100-romulus: Configure audio Konrad Dybcio
2024-11-22 2:14 ` [PATCH 2/3] arm64: dts: qcom: x1e80100-romulus: Set up PCIe3 / SDCard reader Konrad Dybcio
@ 2024-11-22 2:14 ` Konrad Dybcio
2024-11-22 9:26 ` Dmitry Baryshkov
2 siblings, 1 reply; 7+ messages in thread
From: Konrad Dybcio @ 2024-11-22 2:14 UTC (permalink / raw)
To: Bjorn Andersson, Konrad Dybcio, Rob Herring, Krzysztof Kozlowski,
Conor Dooley
Cc: Marijn Suijten, linux-arm-msm, devicetree, linux-kernel, Konrad Dybcio
From: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
The Laptop 7 features two USB-C ports, each one sporting a PS8830 USB-C
retimer/mux. Wire them up.
Signed-off-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
---
.../boot/dts/qcom/x1e80100-microsoft-romulus.dtsi | 282 ++++++++++++++++++++-
1 file changed, 276 insertions(+), 6 deletions(-)
diff --git a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
index 66a12b20b096baa7d5cf8c5fb65927b765aa18ff..f930d228a6fc529acb946d0ac13cdd212808238f 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-microsoft-romulus.dtsi
@@ -124,7 +124,15 @@ port@1 {
reg = <1>;
pmic_glink_ss0_ss_in: endpoint {
- remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ remote-endpoint = <&retimer_ss0_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss0_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss0_con_sbu_out>;
};
};
};
@@ -153,7 +161,15 @@ port@1 {
reg = <1>;
pmic_glink_ss1_ss_in: endpoint {
- remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+ remote-endpoint = <&retimer_ss1_ss_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ pmic_glink_ss1_con_sbu_in: endpoint {
+ remote-endpoint = <&retimer_ss1_con_sbu_out>;
};
};
};
@@ -185,6 +201,109 @@ vreg_edp_3p3: regulator-edp-3p3 {
regulator-boot-on;
};
+ vreg_rtmr0_1p15: regulator-rtmr0-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_1P15";
+
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&pmc8380_5_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&rtmr0_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_1p8: regulator-rtmr0-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_1P8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&pm8550ve_9_gpios 8 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&rtmr0_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr0_3p3: regulator-rtmr0-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR0_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&pm8550_gpios 11 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&rtmr0_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_1p15: regulator-rtmr1-1p15 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_1P15";
+
+ regulator-min-microvolt = <1150000>;
+ regulator-max-microvolt = <1150000>;
+
+ gpio = <&tlmm 188 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&rtmr1_1p15_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_1p8: regulator-rtmr1-1p8 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_1P8";
+
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <1800000>;
+
+ gpio = <&tlmm 175 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&rtmr1_1p8_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+ vreg_rtmr1_3p3: regulator-rtmr1-3p3 {
+ compatible = "regulator-fixed";
+
+ regulator-name = "VREG_RTMR1_3P3";
+
+ regulator-min-microvolt = <3300000>;
+ regulator-max-microvolt = <3300000>;
+
+ gpio = <&tlmm 186 GPIO_ACTIVE_HIGH>;
+ enable-active-high;
+
+ pinctrl-0 = <&rtmr1_3p3_reg_en>;
+ pinctrl-names = "default";
+
+ regulator-boot-on;
+ };
+
+
vreg_nvme: regulator-nvme {
compatible = "regulator-fixed";
@@ -665,7 +784,59 @@ &i2c3 {
status = "okay";
- /* PS8830 USB retimer @8 */
+ /* Left-side rear port */
+ typec-mux@8 {
+ compatible = "parade,ps8830";
+ reg = <0x8>;
+
+ reset-gpios = <&pm8550_gpios 10 GPIO_ACTIVE_LOW>;
+
+ clocks = <&rpmhcc RPMH_RF_CLK3>;
+ clock-names = "xo";
+
+ vdd-supply = <&vreg_rtmr0_1p15>;
+ vdd33-supply = <&vreg_rtmr0_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr0_3p3>;
+ vddar-supply = <&vreg_rtmr0_1p15>;
+ vddat-supply = <&vreg_rtmr0_1p15>;
+ vddio-supply = <&vreg_rtmr0_1p8>;
+
+ pinctrl-0 = <&rtmr0_default>;
+ pinctrl-names = "default";
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss0_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss0_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss0_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss0_con_sbu_in>;
+ };
+ };
+ };
+ };
+
};
&i2c4 {
@@ -699,7 +870,55 @@ &i2c7 {
status = "okay";
- /* PS8830 USB retimer @8 */
+ /* Left-side front port */
+ typec-mux@8 {
+ compatible = "parade,ps8830";
+ reg = <0x8>;
+
+ reset-gpios = <&tlmm 176 GPIO_ACTIVE_LOW>;
+
+ clocks = <&rpmhcc RPMH_RF_CLK4>;
+ clock-names = "xo";
+
+ vdd-supply = <&vreg_rtmr1_1p15>;
+ vdd33-supply = <&vreg_rtmr1_3p3>;
+ vdd33-cap-supply = <&vreg_rtmr1_3p3>;
+ vddar-supply = <&vreg_rtmr1_1p15>;
+ vddat-supply = <&vreg_rtmr1_1p15>;
+ vddio-supply = <&vreg_rtmr1_1p8>;
+
+ retimer-switch;
+ orientation-switch;
+
+ ports {
+ #address-cells = <1>;
+ #size-cells = <0>;
+
+ port@0 {
+ reg = <0>;
+
+ retimer_ss1_ss_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_ss_in>;
+ };
+ };
+
+ port@1 {
+ reg = <1>;
+
+ retimer_ss1_ss_in: endpoint {
+ remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+ };
+ };
+
+ port@2 {
+ reg = <2>;
+
+ retimer_ss1_con_sbu_out: endpoint {
+ remote-endpoint = <&pmic_glink_ss1_con_sbu_in>;
+ };
+ };
+ };
+ };
};
&lpass_tlmm {
@@ -818,6 +1037,20 @@ &pcie6a_phy {
status = "okay";
};
+&pm8550_gpios {
+ rtmr0_default: rtmr0-reset-n-active-state {
+ pins = "gpio10";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ };
+
+ rtmr0_3p3_reg_en: rtmr0-3p3-reg-en-state {
+ pins = "gpio11";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ };
+};
+
&pm8550ve_2_gpios {
sde7_main_reg_en: sde7-main-reg-en-state {
pins = "gpio6";
@@ -830,6 +1063,14 @@ sde7_aux_reg_en: sde7-aux-reg-en-state {
};
};
+&pmc8380_5_gpios {
+ rtmr0_1p15_reg_en: rtmr0-1p15-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ };
+};
+
&pm8550ve_8_gpios {
vreg_12v_x8_en: 12v-x8-reg-en-state {
pins = "gpio8";
@@ -837,6 +1078,14 @@ vreg_12v_x8_en: 12v-x8-reg-en-state {
};
};
+&pm8550ve_9_gpios {
+ rtmr0_1p8_reg_en: rtmr0-1p8-reg-en-state {
+ pins = "gpio8";
+ function = "normal";
+ power-source = <1>; /* 1.8V */
+ };
+};
+
&pmc8380_3_gpios {
edp_bl_en: edp-bl-en-state {
pins = "gpio4";
@@ -1032,6 +1281,27 @@ wake-n-pins {
};
};
+ rtmr1_1p8_reg_en: rtmr1-1p8-reg-en-state {
+ pins = "gpio175";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rtmr1_3p3_reg_en: rtmr1-3p3-reg-en-state {
+ pins = "gpio186";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
+ rtmr1_1p15_reg_en: rtmr1-1p15-reg-en-state {
+ pins = "gpio188";
+ function = "gpio";
+ drive-strength = <2>;
+ bias-disable;
+ };
+
wcd_default: wcd-reset-n-active-state {
pins = "gpio191";
function = "gpio";
@@ -1092,7 +1362,7 @@ &usb_1_ss0_dwc3_hs {
};
&usb_1_ss0_qmpphy_out {
- remote-endpoint = <&pmic_glink_ss0_ss_in>;
+ remote-endpoint = <&retimer_ss0_ss_in>;
};
&usb_1_ss1_hsphy {
@@ -1124,7 +1394,7 @@ &usb_1_ss1_dwc3_hs {
};
&usb_1_ss1_qmpphy_out {
- remote-endpoint = <&pmic_glink_ss1_ss_in>;
+ remote-endpoint = <&retimer_ss1_ss_in>;
};
/* MP0 goes to the Surface Connector, MP1 goes to the USB-A port */
--
2.47.0
^ permalink raw reply [flat|nested] 7+ messages in thread