* [PATCH] fbdev: smscufx: bail out of ufx_set_vid_mode() when the device is gone
@ 2026-11-02 7:21 YuanZhe Liu
2026-11-02 8:57 ` [PATCH v2] fbdev: smscufx: keep the usb_device alive while ufx_data is in use YuanZhe Liu
0 siblings, 1 reply; 3+ messages in thread
From: YuanZhe Liu @ 2026-11-02 7:21 UTC (permalink / raw)
To: Helge Deller, Steve Glendinning
Cc: linux-fbdev, dri-devel, linux-kernel, stable, Bin Yu, Cheng Wen
ufx_usb_disconnect() marks the device as virtualized and clears
usb_active, but the fbdev entry points that program the controller are
not serialized against it. ufx_handle_damage(), ufx_dpy_deferred_io()
and ufx_ops_ioctl() all return early while usb_active is clear;
ufx_set_vid_mode() does not, so a mode set or a blank request that
races with the disconnect keeps issuing control transfers through
dev->udev.
The usb_device is released once the disconnect callback returns, while
dev->udev is left pointing at it, so those transfers dereference a
stale pointer and fault in __create_pipe():
general protection fault, probably for non-canonical address
0xdffffc0000000006: 0000 [#1] SMP
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
RIP: 0010:__create_pipe include/linux/usb.h:2031
Call Trace:
ufx_set_vid_mode
ufx_ops_set_par
fb_set_var
fb_set_var_from_user
store_rotate
Return -ENODEV from ufx_set_vid_mode() when the device is no longer
active, matching the check the other transmit paths already use. Both
callers, ufx_ops_set_par() and ufx_ops_blank(), handle the error: the
former skips the greenscreen fill and keeps the previous mode, the
latter already ignores the result.
The guard cannot live in ufx_reg_write()/ufx_reg_read() instead, since
probe programs the controller through ufx_config_ddr2(),
ufx_i2c_init(), ufx_setup_modes() and ufx_reg_set_bits() before it sets
usb_active.
Fixes: 3c8a63e22a08 ("Add support for SMSC UFX6000/7000 USB display adapters")
Cc: stable@vger.kernel.org
Co-developed-by: Bin Yu <byu@xidian.edu.cn>
Signed-off-by: Bin Yu <byu@xidian.edu.cn>
Co-developed-by: Cheng Wen <wencheng@xidian.edu.cn>
Signed-off-by: Cheng Wen <wencheng@xidian.edu.cn>
Signed-off-by: YuanZhe Liu <25031212351@stu.xidian.edu.cn>
---
drivers/video/fbdev/smscufx.c | 6 +++++-
1 file changed, 5 insertions(+), 1 deletion(-)
diff --git a/drivers/video/fbdev/smscufx.c b/drivers/video/fbdev/smscufx.c
index 5704f60e1741..f1b640a5d712 100644
--- a/drivers/video/fbdev/smscufx.c
+++ b/drivers/video/fbdev/smscufx.c
@@ -661,8 +661,12 @@ static int ufx_set_vid_mode(struct ufx_data *dev, struct fb_var_screeninfo *var)
u32 temp;
u16 h_total, h_active, h_blank_start, h_blank_end, h_sync_start, h_sync_end;
u16 v_total, v_active, v_blank_start, v_blank_end, v_sync_start, v_sync_end;
+ int status;
+
+ if (!atomic_read(&dev->usb_active))
+ return -ENODEV;
- int status = ufx_reg_write(dev, 0x8028, 0);
+ status = ufx_reg_write(dev, 0x8028, 0);
check_warn_return(status, "ufx_set_vid_mode error disabling RGB pad");
status = ufx_reg_write(dev, 0x8024, 0);
--
2.34.1
^ permalink raw reply [flat|nested] 3+ messages in thread* [PATCH v2] fbdev: smscufx: keep the usb_device alive while ufx_data is in use
2026-11-02 7:21 [PATCH] fbdev: smscufx: bail out of ufx_set_vid_mode() when the device is gone YuanZhe Liu
@ 2026-11-02 8:57 ` YuanZhe Liu
2026-11-18 19:15 ` Helge Deller
0 siblings, 1 reply; 3+ messages in thread
From: YuanZhe Liu @ 2026-11-02 8:57 UTC (permalink / raw)
To: Helge Deller, Steve Glendinning
Cc: linux-fbdev, dri-devel, linux-kernel, stable, Bin Yu, Cheng Wen
ufx_usb_probe() stores the usb_device pointer in dev->udev without
taking a reference, and ufx_usb_disconnect() does not wait for in-flight
control transfers. A mode set or blank request that runs while the
device is being unplugged - through ufx_ops_set_par() or ufx_ops_blank()
on an open /dev/fbN file - keeps issuing synchronous control messages for
the whole ufx_set_vid_mode() sequence, including two msleep(1) delays in
ufx_config_pix_clk(). Once the disconnect callback returns, the USB core
may release the usb_device, and the next ufx_reg_write()/ufx_reg_read()
dereferences dev->udev through __create_pipe():
general protection fault, probably for non-canonical address
0xdffffc0000000006: 0000 [#1] SMP
KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
RIP: __create_pipe include/linux/usb.h:2031
Call Trace:
ufx_set_vid_mode
ufx_ops_set_par
fb_set_var
fb_set_var_from_user
store_rotate
Take a reference to the usb_device in ufx_usb_probe() and drop it in
ufx_free(), so dev->udev and dev->gdev stay valid until the last
ufx_data user is gone. The control transfers then fail with -ENODEV
instead of dereferencing freed memory.
Also return early from ufx_set_vid_mode() while the device is inactive,
matching the other transmit paths. That check alone is not enough,
because it is not serialized against ufx_usb_disconnect() and the
transfer sequence continues after it; it only avoids a long series of
failing transfers.
Fixes: 3c8a63e22a08 ("Add support for SMSC UFX6000/7000 USB display adapters")
Cc: stable@vger.kernel.org
---
Changes in v2:
- Hold a reference to the usb_device and drop it in ufx_free() so
dev->udev stays valid for the whole transfer sequence; the
usb_active check alone only covers the entry (review feedback).
drivers/video/fbdev/smscufx.c | 9 ++++++++-
1 file changed, 8 insertions(+), 1 deletion(-)
diff --git a/drivers/video/fbdev/smscufx.c b/drivers/video/fbdev/smscufx.c
index 5704f60e1741..eac303adb69a 100644
--- a/drivers/video/fbdev/smscufx.c
+++ b/drivers/video/fbdev/smscufx.c
@@ -661,8 +661,12 @@ static int ufx_set_vid_mode(struct ufx_data *dev, struct fb_var_screeninfo *var)
u32 temp;
u16 h_total, h_active, h_blank_start, h_blank_end, h_sync_start, h_sync_end;
u16 v_total, v_active, v_blank_start, v_blank_end, v_sync_start, v_sync_end;
+ int status;
+
+ if (!atomic_read(&dev->usb_active))
+ return -ENODEV;
- int status = ufx_reg_write(dev, 0x8028, 0);
+ status = ufx_reg_write(dev, 0x8028, 0);
check_warn_return(status, "ufx_set_vid_mode error disabling RGB pad");
status = ufx_reg_write(dev, 0x8024, 0);
@@ -1064,6 +1068,7 @@ static void ufx_free(struct kref *kref)
{
struct ufx_data *dev = container_of(kref, struct ufx_data, kref);
+ usb_put_dev(dev->udev);
kfree(dev);
}
@@ -1606,6 +1611,8 @@ static int ufx_usb_probe(struct usb_interface *interface,
dev->udev = usbdev;
dev->gdev = &usbdev->dev; /* our generic struct device * */
+ /* keep the device alive until the last ufx_data user is gone */
+ usb_get_dev(usbdev);
usb_set_intfdata(interface, dev);
dev_dbg(dev->gdev, "%s %s - serial #%s\n",
--
2.34.1
^ permalink raw reply [flat|nested] 3+ messages in thread* Re: [PATCH v2] fbdev: smscufx: keep the usb_device alive while ufx_data is in use
2026-11-02 8:57 ` [PATCH v2] fbdev: smscufx: keep the usb_device alive while ufx_data is in use YuanZhe Liu
@ 2026-11-18 19:15 ` Helge Deller
0 siblings, 0 replies; 3+ messages in thread
From: Helge Deller @ 2026-11-18 19:15 UTC (permalink / raw)
To: YuanZhe Liu, Steve Glendinning
Cc: linux-fbdev, dri-devel, linux-kernel, Bin Yu, Cheng Wen
On 11/2/26 09:57, YuanZhe Liu wrote:
> ufx_usb_probe() stores the usb_device pointer in dev->udev without
> taking a reference, and ufx_usb_disconnect() does not wait for in-flight
> control transfers. A mode set or blank request that runs while the
> device is being unplugged - through ufx_ops_set_par() or ufx_ops_blank()
> on an open /dev/fbN file - keeps issuing synchronous control messages for
> the whole ufx_set_vid_mode() sequence, including two msleep(1) delays in
> ufx_config_pix_clk(). Once the disconnect callback returns, the USB core
> may release the usb_device, and the next ufx_reg_write()/ufx_reg_read()
> dereferences dev->udev through __create_pipe():
>
> general protection fault, probably for non-canonical address
> 0xdffffc0000000006: 0000 [#1] SMP
> KASAN: null-ptr-deref in range [0x0000000000000030-0x0000000000000037]
> RIP: __create_pipe include/linux/usb.h:2031
> Call Trace:
> ufx_set_vid_mode
> ufx_ops_set_par
> fb_set_var
> fb_set_var_from_user
> store_rotate
>
> Take a reference to the usb_device in ufx_usb_probe() and drop it in
> ufx_free(), so dev->udev and dev->gdev stay valid until the last
> ufx_data user is gone. The control transfers then fail with -ENODEV
> instead of dereferencing freed memory.
>
> Also return early from ufx_set_vid_mode() while the device is inactive,
> matching the other transmit paths. That check alone is not enough,
> because it is not serialized against ufx_usb_disconnect() and the
> transfer sequence continues after it; it only avoids a long series of
> failing transfers.
>
> Fixes: 3c8a63e22a08 ("Add support for SMSC UFX6000/7000 USB display adapters")
> Cc: stable@vger.kernel.org
> ---
> Changes in v2:
> - Hold a reference to the usb_device and drop it in ufx_free() so
> dev->udev stays valid for the whole transfer sequence; the
> usb_active check alone only covers the entry (review feedback).
> drivers/video/fbdev/smscufx.c | 9 ++++++++-
> 1 file changed, 8 insertions(+), 1 deletion(-)
applied.
Thanks!
Helge
^ permalink raw reply [flat|nested] 3+ messages in thread
end of thread, other threads:[~2026-11-18 19:16 UTC | newest]
Thread overview: 3+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-02 7:21 [PATCH] fbdev: smscufx: bail out of ufx_set_vid_mode() when the device is gone YuanZhe Liu
2026-11-02 8:57 ` [PATCH v2] fbdev: smscufx: keep the usb_device alive while ufx_data is in use YuanZhe Liu
2026-11-18 19:15 ` Helge Deller
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®