Re: linux-2.4.21 released

["Fr�d�ric L. W. Meunier" <0@pervalidus.tk>]

http://marc.theaimsgroup.com/?l=linux-kernel&m=105572386027023&w=2

Nobody replied but let me do my last report.

> I just tested with 2.4.21. With IO-APIC everything worked
> except the ethernet.

My ECS K7VTA3 5.0C is useless with Linux since I can't get
ethernet to work with IO-APIC, and without it modprobe usb-uhci
just freezes everything. It may be a broken motherboard. I
can't believe all 5.0 have so many problems, but...

...I wonder what's so different in Windows XP. As I reported
ethernet and USB work together there.

My last try was ACPI, but while the ethernet worked, the USB
and onboard sound didn't:

# modprobe usbcore
...

# modprobe usb-uhci
...

Sorry, I couldn't copy all lines, but you get the idea.

usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 2
hub.c: USB hub found
hub.c: 2 ports detected
PCI: No IRQ known for interrupt pin C of device 00:10.2
usb-uhci.c: USB UHCI at I/O 0xdc00, IRQ 10
usb-uhci.c: Detected 2 ports
usb.c: new USB bus registered, assigned bus number 3
hub.c: USB hub found
hub.c: 2 ports detected
usb-uhci.c: v1.275:USB Universal Host Controller Interface driver
hub.c: new USB device 00:10.0-1, assigned address 2
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=2 (error=-110)
hub.c: new USB device 00:10.0-1, assigned address 3
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=3 (error=-110)

# modprobe ehci-hcd
PCI: No IRQ known for interrupt pin D of device 00:10.3
ehci-hcd 00:10.3: VIA Technologies, Inc. USB 2.0
ehci-hcd 00:10.3: irq 11, pci mem e286f000
usb.c: new USB bus registered, assigned bus number 4
PCI: 00:10.3 PCI cache line size set incorrectly (32 bytes) by BIOS/FW.
PCI: 00:10.3 PCI cache line size corrected to 64.
ehci-hcd 00:10.3: USB 2.0 enabled, EHCI 1.00, driver 2003-Jan-22
hub.c: USB hub found
hub.c: 6 ports detected
hub.c: new USB device 00:10.0-1, assigned address 4
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=4 (error=-110)
hub.c: new USB device 00:10.0-1, assigned address 5
usb_control/bulk_msg: timeout
usb.c: USB device not accepting new address=5 (error=-110)

# modprobe sound
Via 686a/8233/8235 audio driver 1.9.1-ac2
PCI: No IRQ known for interrupt pin C of device 00:11.5
via82cxxx: Six channel audio available
ac97_codec: AC97 Audio codec, id: VIA97 (Unknown)
via82cxxx: board #1 at 0xE400, IRQ 10

Any sound loops at the start and the kernel reports

via_audio: ignoring drain playback error -512

I also tried ACPI with noapic, but things got worse. The
ethernet and sound worked, but everything reported an awful
amount of APIC error on CPU0: 40(40). 'shutdown -r now' did the
same and I finally rebooted with SysRq.

My last ECS, really. The BIOS is even worse. If you disable
RAID and 1394 the menus just disappear and you can't reenable
them.