From: Meelis Roos <mroos@linux.ee>
To: matthieu castet <castet.matthieu@free.fr>
Cc: Linux Kernel list <linux-kernel@vger.kernel.org>,
Jean Tourrilhes <jt@bougret.hpl.hp.com>,
Adam Belay <ambx1@neo.rr.com>,
"Li, Shaohua" <shaohua.li@intel.com>,
acpi-devel@lists.sourceforge.net
Subject: Re: [PATCH] smsc-ircc2: Add PnP support.
Date: Sat, 20 Nov 2004 01:09:36 +0200 (EET) [thread overview]
Message-ID: <Pine.SOC.4.61.0411200102580.12992@math.ut.ee> (raw)
In-Reply-To: <419E3B7A.4000904@free.fr>
I tried it with pnpbios (acpi=off) and it started to work after auto and
activate (but not with auto alone):
nartsiss:/# modprobe smsc-ircc2
found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227
smsc_superio_flat(): IrDA not enabled
smsc_superio_flat(): fir: 0x00, sir: 0x00, dma: 15, irq: 0, mode: 0x02
FATAL: Error inserting smsc_ircc2 (/lib/modules/2.6.10-rc2/kernel/drivers/net/irda/smsc-ircc2.ko): No such device
nartsiss:/# echo activate > resources
pnp: Device 00:0f activated.
nartsiss:/# modprobe smsc-ircc2
found SMC SuperIO Chip (devid=0x5a rev=00 base=0x002e): LPC47N227
smsc_superio_flat(): fir: 0x2e8, sir: 0x100, dma: 03, irq: 5, mode: 0x0e
SMsC IrDA Controller found
IrCC version 2.0, firport 0x2e8, sirport 0x100 dma=3, irq=5
No transceiver found. Defaulting to Fast pin select
IrDA: Registered device irda0
>>> Could you send me the result of : "for i in /sys/bus/pnp/devices/*; do cat
>>> $i/id $i/options; done" in order to see if other devices have missing
>>> resources ?
The output with pnpbios is below for comparision.
>> PNP0c01
>> PNP0200
>> PNP0800
>> PNP0c04
>> PNP0303
>> PNP0f13
>> PNP0b00
>> PNP0c02
>> PNP0700
>> port 0x3f0-0x3f0, align 0x0, size 0x6, 16-bit address decoding
>> port 0x3f7-0x3f7, align 0x0, size 0x1, 16-bit address decoding
>> irq 6 High-Edge
>> dma 2 8-bit compatible
> floppy : seem ok
>> PNP0501
>> Dependent: 01 - Priority acceptable
>> port 0x3f8-0x3f8, align 0x0, size 0x8, 16-bit address decoding
>> Dependent: 02 - Priority acceptable
>> port 0x2f8-0x2f8, align 0x0, size 0x8, 16-bit address decoding
>> Dependent: 03 - Priority acceptable
>> port 0x2e8-0x2e8, align 0x0, size 0x8, 16-bit address decoding
>> Dependent: 04 - Priority acceptable
>> port 0x3e8-0x3e8, align 0x0, size 0x8, 16-bit address decoding
> serial miss irq
>> SMCf010
>> Dependent: 01 - Priority acceptable
>> port 0x3f8-0x3f8, align 0x0, size 0x8, 16-bit address decoding
>> Dependent: 02 - Priority acceptable
>> port 0x2e8-0x2e8, align 0x0, size 0x8, 16-bit address decoding
>> Dependent: 03 - Priority acceptable
>> port 0x2f8-0x2f8, align 0x0, size 0x8, 16-bit address decoding
>> Dependent: 04 - Priority acceptable
>> port 0x3e8-0x3e8, align 0x0, size 0x8, 16-bit address decoding
> irda : miss io,irq,dma
>> PNP0401
>> Dependent: 01 - Priority acceptable
>> port 0x378-0x378, align 0x0, size 0x3, 16-bit address decoding
>> port 0x778-0x778, align 0x0, size 0x3, 16-bit address decoding
>> irq 7 High-Edge
>> Dependent: 02 - Priority acceptable
>> port 0x278-0x278, align 0x0, size 0x3, 16-bit address decoding
>> port 0x678-0x678, align 0x0, size 0x3, 16-bit address decoding
>> irq 5 High-Edge
>> Dependent: 03 - Priority acceptable
>> port 0x3bc-0x3bc, align 0x0, size 0x3, 16-bit address decoding
>> port 0x7bc-0x7bc, align 0x0, size 0x3, 16-bit address decoding
>> irq 7 High-Edge
> parallel port: miss dma
>> TOS6200
>>
PNP0c01
PNP0200
PNP0000
PNP0100
PNP0800
PNP0c04
PNP0303
PNP0f13
irq 12 High-Edge
PNP0b00
PNP0c02
PNP0700
port 0x3f0-0x3f0, align 0x0, size 0x6, 16-bit address decoding
port 0x3f7-0x3f7, align 0x0, size 0x1, 16-bit address decoding
irq 6 High-Edge
dma 2 8-bit byte-count compatible
PNP0501
irq 3,4,5,7,10,11 High-Edge
Dependent: 01 - Priority acceptable
port 0x3f8-0x3f8, align 0x0, size 0x8, 16-bit address decoding
Dependent: 02 - Priority acceptable
port 0x2f8-0x2f8, align 0x0, size 0x8, 16-bit address decoding
Dependent: 03 - Priority acceptable
port 0x2e8-0x2e8, align 0x0, size 0x8, 16-bit address decoding
Dependent: 04 - Priority acceptable
port 0x3e8-0x3e8, align 0x0, size 0x8, 16-bit address decoding
SMCf010
PNP0510
port 0x100-0x130, align 0xf, size 0x8, 16-bit address decoding
irq 3,4,5,7,10,11 High-Edge
dma 1,2,3 16-bit byte-count compatible
Dependent: 01 - Priority acceptable
port 0x3f8-0x3f8, align 0x0, size 0x8, 16-bit address decoding
Dependent: 02 - Priority acceptable
port 0x2e8-0x2e8, align 0x0, size 0x8, 16-bit address decoding
Dependent: 03 - Priority acceptable
port 0x2f8-0x2f8, align 0x0, size 0x8, 16-bit address decoding
Dependent: 04 - Priority acceptable
port 0x3e8-0x3e8, align 0x0, size 0x8, 16-bit address decoding
PNP0401
dma 1,2,3 8-bit byte-count compatible
Dependent: 01 - Priority acceptable
port 0x378-0x378, align 0x0, size 0x3, 16-bit address decoding
port 0x778-0x778, align 0x0, size 0x3, 16-bit address decoding
irq 7 High-Edge
Dependent: 02 - Priority acceptable
port 0x278-0x278, align 0x0, size 0x3, 16-bit address decoding
port 0x678-0x678, align 0x0, size 0x3, 16-bit address decoding
irq 5 High-Edge
Dependent: 03 - Priority acceptable
port 0x3bc-0x3bc, align 0x0, size 0x3, 16-bit address decoding
port 0x7bc-0x7bc, align 0x0, size 0x3, 16-bit address decoding
irq 7 High-Edge
PNP0a03
PNP0e03
PNP0e00
Dependent: 01 - Priority acceptable
port 0x3e0-0x3e0, align 0x0, size 0x2, 16-bit address decoding
irq <none> High-Edge
Dependent: 02 - Priority acceptable
port 0x3e0-0x3e0, align 0x0, size 0x2, 16-bit address decoding
irq 3,4,5,7,10,11 High-Edge
--
Meelis Roos (mroos@linux.ee)
next prev parent reply other threads:[~2004-11-19 23:36 UTC|newest]
Thread overview: 37+ messages / expand[flat|nested] mbox.gz Atom feed top
2004-11-18 18:42 matthieu castet
2004-11-18 18:55 ` Jean Tourrilhes
2004-11-18 19:49 ` matthieu castet
2004-11-18 20:41 ` Ville Syrjälä
2004-11-18 23:02 ` Adam Belay
2004-11-19 15:27 ` Meelis Roos
2004-11-19 15:53 ` matthieu castet
2004-11-19 15:57 ` matthieu castet
2004-11-19 16:15 ` Meelis Roos
2004-11-19 16:22 ` Meelis Roos
2004-11-19 17:28 ` matthieu castet
2004-11-19 17:34 ` Meelis Roos
2004-11-19 18:29 ` matthieu castet
2004-11-19 23:09 ` Meelis Roos [this message]
2004-11-20 9:50 ` matthieu castet
2004-11-21 17:50 ` Meelis Roos
2004-11-21 18:16 ` matthieu castet
2004-11-21 18:51 ` Meelis Roos
2004-11-21 19:21 ` matthieu castet
2004-11-21 20:20 ` matthieu castet
2004-11-22 1:29 ` Li Shaohua
2004-11-22 8:37 ` Meelis Roos
2004-11-26 16:02 ` matthieu castet
2004-11-26 18:19 ` Meelis Roos
2004-11-27 0:50 ` matthieu castet
2004-11-27 12:15 ` Meelis Roos
2004-11-27 14:02 ` matthieu castet
2004-11-27 18:24 ` Meelis Roos
2004-11-27 18:58 ` matthieu castet
2004-11-27 19:25 ` matthieu castet
2004-11-27 19:39 ` Meelis Roos
2004-11-22 8:39 ` Meelis Roos
2004-11-22 8:42 ` Meelis Roos
2004-11-22 8:38 ` Meelis Roos
2004-11-20 11:43 ` [ACPI] " Ville Syrjälä
2004-11-20 11:57 ` matthieu castet
[not found] <20041117232047.GA28061@bougret.hpl.hp.com>
2004-11-18 3:52 ` Ville Syrjälä
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=Pine.SOC.4.61.0411200102580.12992@math.ut.ee \
--to=mroos@linux.ee \
--cc=acpi-devel@lists.sourceforge.net \
--cc=ambx1@neo.rr.com \
--cc=castet.matthieu@free.fr \
--cc=jt@bougret.hpl.hp.com \
--cc=linux-kernel@vger.kernel.org \
--cc=shaohua.li@intel.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
Powered by JetHome