* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-11-16 5:25 Duke Xin
2022-11-16 6:01 ` Greg KH
0 siblings, 1 reply; 14+ messages in thread
From: Duke Xin @ 2022-11-16 5:25 UTC (permalink / raw)
To: johan, gregkh; +Cc: linux-usb, linux-kernel, jerry.meng, duke.xin, Duke Xin
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0311 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0311 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin <duke_xinanwen@163.com>
---
drivers/usb/serial/option.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 37257a52287d..b740672be0cd 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);
#define QUECTEL_PRODUCT_BG96 0x0296
#define QUECTEL_PRODUCT_EP06 0x0306
#define QUECTEL_PRODUCT_EM05G 0x030a
+#define QUECTEL_PRODUCT_EM05G_SG 0x0311
#define QUECTEL_PRODUCT_EM060K 0x030b
#define QUECTEL_PRODUCT_EM12 0x0512
#define QUECTEL_PRODUCT_RM500Q 0x0800
@@ -1151,6 +1152,8 @@ static const struct usb_device_id option_ids[] = {
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
.driver_info = RSVD(6) | ZLP },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),/* Quectel EM05G smart gateway*/
+ .driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
--
2.34.1
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
2022-11-16 5:25 [PATCH] USB: serial: option: add Quectel EM05-G modem Duke Xin
@ 2022-11-16 6:01 ` Greg KH
0 siblings, 0 replies; 14+ messages in thread
From: Greg KH @ 2022-11-16 6:01 UTC (permalink / raw)
To: Duke Xin; +Cc: johan, linux-usb, linux-kernel, jerry.meng, duke.xin
On Wed, Nov 16, 2022 at 01:25:37PM +0800, Duke Xin wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
Why do you have extra spaces in your subject and in the text here?
Please fix up.
And properly version your patches, as the documentation asks you to.
thanks,
greg k-h
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-12-27 9:51 Duke Xin(辛安文)
2023-01-12 16:48 ` Johan Hovold
0 siblings, 1 reply; 14+ messages in thread
From: Duke Xin(辛安文) @ 2022-12-27 9:51 UTC (permalink / raw)
To: johan, gregkh
Cc: linux-usb, linux-kernel, jerry.meng, duke.xin,
Duke Xin(辛安文)
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0314 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0314 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
---
drivers/usb/serial/option.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index dee79c7d82d5..df05b0b26eef 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -256,6 +256,7 @@ static void option_instat_callback(struct urb *urb);
#define QUECTEL_PRODUCT_EM05G 0x030a
#define QUECTEL_PRODUCT_EM060K 0x030b
#define QUECTEL_PRODUCT_EM05G_SG 0x0311
+#define QUECTEL_PRODUCT_EM05G_RS 0x0314
#define QUECTEL_PRODUCT_EM12 0x0512
#define QUECTEL_PRODUCT_RM500Q 0x0800
#define QUECTEL_PRODUCT_RM520N 0x0801
@@ -1163,6 +1164,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
.driver_info = RSVD(6) | ZLP },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_RS, 0xff),
+ .driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
--
2.25.1
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
2022-12-27 9:51 Duke Xin(辛安文)
@ 2023-01-12 16:48 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2023-01-12 16:48 UTC (permalink / raw)
To: Duke Xin(辛安文)
Cc: gregkh, linux-usb, linux-kernel, jerry.meng, duke.xin
On Tue, Dec 27, 2022 at 01:51:27AM -0800, Duke Xin(辛安文) wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
This is the third (fourth?) patch adding support for "EM05-G". Please
make sure that your patch summaries (Subject) are unique so that it is
possible to tell the patches apart.
I've added GR etc in parenthesis after the model name, but please
remember to do so yourself in the future.
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
>
> "RMNET" : AT + DIAG + NMEA + Modem + QMI
> "MBIM" : MBIM + AT + DIAG + NMEA + Modem
Now applied, thanks.
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-12-27 9:44 Duke Xin(辛安文)
0 siblings, 0 replies; 14+ messages in thread
From: Duke Xin(辛安文) @ 2022-12-27 9:44 UTC (permalink / raw)
To: johan, gregkh
Cc: linux-usb, linux-kernel, jerry.meng, duke.xin,
Duke Xin(辛安文)
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0313 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0313 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
---
drivers/usb/serial/option.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index dee79c7d82d5..26796deb6da8 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -256,6 +256,7 @@ static void option_instat_callback(struct urb *urb);
#define QUECTEL_PRODUCT_EM05G 0x030a
#define QUECTEL_PRODUCT_EM060K 0x030b
#define QUECTEL_PRODUCT_EM05G_SG 0x0311
+#define QUECTEL_PRODUCT_EM05G_GR 0x0313
#define QUECTEL_PRODUCT_EM12 0x0512
#define QUECTEL_PRODUCT_RM500Q 0x0800
#define QUECTEL_PRODUCT_RM520N 0x0801
@@ -1163,6 +1164,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
.driver_info = RSVD(6) | ZLP },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_GR, 0xff),
+ .driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
--
2.25.1
^ permalink raw reply [flat|nested] 14+ messages in thread* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-12-27 9:28 Duke Xin(辛安文)
2023-01-12 16:36 ` Johan Hovold
0 siblings, 1 reply; 14+ messages in thread
From: Duke Xin(辛安文) @ 2022-12-27 9:28 UTC (permalink / raw)
To: johan, gregkh
Cc: linux-usb, linux-kernel, jerry.meng, duke.xin,
Duke Xin(辛安文)
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030C Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030C Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
---
drivers/usb/serial/option.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index dee79c7d82d5..d4c914f3b8bf 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -255,6 +255,7 @@ static void option_instat_callback(struct urb *urb);
#define QUECTEL_PRODUCT_EP06 0x0306
#define QUECTEL_PRODUCT_EM05G 0x030a
#define QUECTEL_PRODUCT_EM060K 0x030b
+#define QUECTEL_PRODUCT_EM05G_CS 0x030C
#define QUECTEL_PRODUCT_EM05G_SG 0x0311
#define QUECTEL_PRODUCT_EM12 0x0512
#define QUECTEL_PRODUCT_RM500Q 0x0800
@@ -1163,6 +1164,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
.driver_info = RSVD(6) | ZLP },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_CS, 0xff),
+ .driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
--
2.25.1
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
2022-12-27 9:28 Duke Xin(辛安文)
@ 2023-01-12 16:36 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2023-01-12 16:36 UTC (permalink / raw)
To: Duke Xin(辛安文)
Cc: gregkh, linux-usb, linux-kernel, jerry.meng, duke.xin
On Tue, Dec 27, 2022 at 01:28:25AM -0800, Duke Xin(辛安文) wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
>
> "RMNET" : AT + DIAG + NMEA + Modem + QMI
> "MBIM" : MBIM + AT + DIAG + NMEA + Modem
>
> The detailed description of the USB configuration for each mode as follows:
>
> RMNET Mode
> --------------
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=030C Rev= 3.18
> S: Manufacturer=Quectel
> S: Product=Quectel EM05-G
> C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
> E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> MBIM Mode
> --------------
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=030C Rev= 3.18
> S: Manufacturer=Quectel
> S: Product=Quectel EM05-G
> C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
> E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> Signed-off-by: Duke Xin(辛安文) <duke_xinanwen@163.com>
> ---
> drivers/usb/serial/option.c | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index dee79c7d82d5..d4c914f3b8bf 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -255,6 +255,7 @@ static void option_instat_callback(struct urb *urb);
> #define QUECTEL_PRODUCT_EP06 0x0306
> #define QUECTEL_PRODUCT_EM05G 0x030a
> #define QUECTEL_PRODUCT_EM060K 0x030b
> +#define QUECTEL_PRODUCT_EM05G_CS 0x030C
nit: the other entries use lowercase hex
> #define QUECTEL_PRODUCT_EM05G_SG 0x0311
> #define QUECTEL_PRODUCT_EM12 0x0512
> #define QUECTEL_PRODUCT_RM500Q 0x0800
> @@ -1163,6 +1164,8 @@ static const struct usb_device_id option_ids[] = {
> .driver_info = RSVD(6) | ZLP },
> { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
> .driver_info = RSVD(6) | ZLP },
> + { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_CS, 0xff),
> + .driver_info = RSVD(6) | ZLP },
And CS comes before SG alphabetically.
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
I fixed the above when applying.
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-11-19 9:44 Duke Xin
2022-11-25 9:26 ` Johan Hovold
0 siblings, 1 reply; 14+ messages in thread
From: Duke Xin @ 2022-11-19 9:44 UTC (permalink / raw)
To: johan, gregkh; +Cc: linux-usb, linux-kernel, jerry.meng, duke.xin, Duke Xin
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0311 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0311 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin <duke_xinanwen@163.com>
---
drivers/usb/serial/option.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index c3b7f1d98e78..fc14df5033d8 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -254,6 +254,7 @@ static void option_instat_callback(struct urb *urb);
#define QUECTEL_PRODUCT_BG96 0x0296
#define QUECTEL_PRODUCT_EP06 0x0306
#define QUECTEL_PRODUCT_EM05G 0x030a
+#define QUECTEL_PRODUCT_EM05G_SG 0x0311
#define QUECTEL_PRODUCT_EM060K 0x030b
#define QUECTEL_PRODUCT_EM12 0x0512
#define QUECTEL_PRODUCT_RM500Q 0x0800
@@ -1160,6 +1161,8 @@ static const struct usb_device_id option_ids[] = {
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
.driver_info = RSVD(6) | ZLP },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
+ .driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
--
2.34.1
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
2022-11-19 9:44 Duke Xin
@ 2022-11-25 9:26 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2022-11-25 9:26 UTC (permalink / raw)
To: Duke Xin; +Cc: gregkh, linux-usb, linux-kernel, jerry.meng, duke.xin
On Sat, Nov 19, 2022 at 05:44:47PM +0800, Duke Xin wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
>
> "RMNET" : AT + DIAG + NMEA + Modem + QMI
> "MBIM" : MBIM + AT + DIAG + NMEA + Modem
>
> The detailed description of the USB configuration for each mode as follows:
...
> Signed-off-by: Duke Xin <duke_xinanwen@163.com>
> ---
This looks much better, thanks!
In the future, when updating a patch you should include a changelog here
below the '---' line and the patch revision should be indicated in the
Subject prefix (e.g. this should have been "[PATCH v3]: USB: serial:
...").
> drivers/usb/serial/option.c | 3 +++
> 1 file changed, 3 insertions(+)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index c3b7f1d98e78..fc14df5033d8 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -254,6 +254,7 @@ static void option_instat_callback(struct urb *urb);
> #define QUECTEL_PRODUCT_BG96 0x0296
> #define QUECTEL_PRODUCT_EP06 0x0306
> #define QUECTEL_PRODUCT_EM05G 0x030a
> +#define QUECTEL_PRODUCT_EM05G_SG 0x0311
These defines should be sorted by PID.
> #define QUECTEL_PRODUCT_EM060K 0x030b
> #define QUECTEL_PRODUCT_EM12 0x0512
> #define QUECTEL_PRODUCT_RM500Q 0x0800
> @@ -1160,6 +1161,8 @@ static const struct usb_device_id option_ids[] = {
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
> { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
> .driver_info = RSVD(6) | ZLP },
> + { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),
> + .driver_info = RSVD(6) | ZLP },
And you have some stray whitespace after the comma here, which would
have been picked up by scripts/checkpatch.pl which you should run on
your patches before submitting them.
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
I've fixed up the above nits (sort order and white space) and applied
this one for 6.2 now so you don't need to send a v4 this time.
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
[parent not found: <20221116105554.329246-1-duke_xinanwen@163.com>]
* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
[not found] <20221116105554.329246-1-duke_xinanwen@163.com>
@ 2022-11-16 11:31 ` Greg KH
0 siblings, 0 replies; 14+ messages in thread
From: Greg KH @ 2022-11-16 11:31 UTC (permalink / raw)
To: Duke Xin; +Cc: johan, linux-usb, linux-kernel, jerry.meng, duke.xin
On Wed, Nov 16, 2022 at 06:55:54PM +0800, Duke Xin wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
>
> "RMNET" : AT + DIAG + NMEA + Modem + QMI
> "MBIM" : MBIM + AT + DIAG + NMEA + Modem
>
> The detailed description of the USB configuration for each mode as follows:
>
> RMNET Mode
> --------------
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=0311 Rev= 3.18
> S: Manufacturer=Quectel
> S: Product=Quectel EM05-G
> C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
> E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
> E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> MBIM Mode
> --------------
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=0311 Rev= 3.18
> S: Manufacturer=Quectel
> S: Product=Quectel EM05-G
> C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
> E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
>
> Signed-off-by: Duke Xin <duke_xinanwen@163.com>
> ---
> drivers/usb/serial/option.c | 4 +++-
> 1 file changed, 3 insertions(+), 1 deletion(-)
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> index 2a0d8fc9af91..b740672be0cd 100644
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);
> #define QUECTEL_PRODUCT_BG96 0x0296
> #define QUECTEL_PRODUCT_EP06 0x0306
> #define QUECTEL_PRODUCT_EM05G 0x030a
> +#define QUECTEL_PRODUCT_EM05G_SG 0x0311
> #define QUECTEL_PRODUCT_EM060K 0x030b
> #define QUECTEL_PRODUCT_EM12 0x0512
> #define QUECTEL_PRODUCT_RM500Q 0x0800
> @@ -1151,6 +1152,8 @@ static const struct usb_device_id option_ids[] = {
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
> { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
> .driver_info = RSVD(6) | ZLP },
> + { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),/* Quectel EM05G smart gateway*/
> + .driver_info = RSVD(6) | ZLP },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
> @@ -2170,7 +2173,6 @@ static const struct usb_device_id option_ids[] = {
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x010a, 0xff) }, /* Fibocom MA510 (ECM mode) */
> { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0xff, 0x30) }, /* Fibocom FG150 Diag */
> { USB_DEVICE_AND_INTERFACE_INFO(0x2cb7, 0x010b, 0xff, 0, 0) }, /* Fibocom FG150 AT */
> - { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x0111, 0xff) }, /* Fibocom FM160 (MBIM mode) */
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a0, 0xff) }, /* Fibocom NL668-AM/NL652-EU (laptop MBIM) */
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a2, 0xff) }, /* Fibocom FM101-GL (laptop MBIM) */
> { USB_DEVICE_INTERFACE_CLASS(0x2cb7, 0x01a4, 0xff), /* Fibocom FM101-GL (laptop MBIM) */
> --
> 2.34.1
>
Hi,
This is the friendly patch-bot of Greg Kroah-Hartman. You have sent him
a patch that has triggered this response. He used to manually respond
to these common problems, but in order to save his sanity (he kept
writing the same thing over and over, yet to different people), I was
created. Hopefully you will not take offence and will fix the problem
in your patch and resubmit it so that it can be accepted into the Linux
kernel tree.
You are receiving this message because of the following common error(s)
as indicated below:
- This looks like a new version of a previously submitted patch, but you
did not list below the --- line any changes from the previous version.
Please read the section entitled "The canonical patch format" in the
kernel file, Documentation/SubmittingPatches for what needs to be done
here to properly describe this.
If you wish to discuss this problem further, or you have questions about
how to resolve this issue, please feel free to respond to this email and
Greg will reply once he has dug out from the pending patches received
from other developers.
thanks,
greg k-h's patch email bot
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-11-11 3:56 Duke Xin
2022-11-15 10:04 ` Johan Hovold
0 siblings, 1 reply; 14+ messages in thread
From: Duke Xin @ 2022-11-11 3:56 UTC (permalink / raw)
To: johan, gregkh; +Cc: linux-usb, linux-kernel, Duke Xin
The EM05-G modem has 2 USB configurations that are configurable via the AT
command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
the following interfaces, respectively:
"RMNET" : AT + DIAG + NMEA + Modem + QMI
"MBIM" : MBIM + AT + DIAG + NMEA + Modem
The detailed description of the USB configuration for each mode as follows:
RMNET Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 21 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0311 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 5 Cfg#= 1 Atr=a0 MxPwr=500mA
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 6 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=ff Prot=ff Driver=(none)
E: Ad=89(I) Atr=03(Int.) MxPS= 8 Ivl=32ms
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
MBIM Mode
--------------
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=0311 Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Duke Xin <duke_xinanwen@163.com>
Cc: stable@vger.kernel.org
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Duke Xin <duke_xinanwen@163.com>
---
drivers/usb/serial/option.c | 3 +++
1 file changed, 3 insertions(+)
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
index 37257a52287d..ec96872e3e5b 100644
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -253,6 +253,7 @@ static void option_instat_callback(struct urb *urb);
#define QUECTEL_PRODUCT_BG96 0x0296
#define QUECTEL_PRODUCT_EP06 0x0306
#define QUECTEL_PRODUCT_EM05G 0x030a
+#define QUECTEL_PRODUCT_EM05G_SG 0x0311
#define QUECTEL_PRODUCT_EM060K 0x030b
#define QUECTEL_PRODUCT_EM12 0x0512
#define QUECTEL_PRODUCT_RM500Q 0x0800
@@ -1151,6 +1152,8 @@ static const struct usb_device_id option_ids[] = {
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EP06, 0xff, 0, 0) },
{ USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G, 0xff),
.driver_info = RSVD(6) | ZLP },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM05G_SG, 0xff),/* Quectel EM05G 4G LTE,Smart Gateway*/
+ .driver_info = RSVD(6) | ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0x00, 0x40) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x30) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EM060K, 0xff, 0xff, 0x40) },
--
2.34.1
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
2022-11-11 3:56 Duke Xin
@ 2022-11-15 10:04 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2022-11-15 10:04 UTC (permalink / raw)
To: Duke Xin; +Cc: gregkh, linux-usb, linux-kernel
On Fri, Nov 11, 2022 at 11:56:31AM +0800, Duke Xin wrote:
> The EM05-G modem has 2 USB configurations that are configurable via the AT
> command AT+QCFG="usbnet",[ 0 | 2 ] which make the modem enumerate with
> the following interfaces, respectively:
The commit message (including Subject) should not be indented like this.
> Signed-off-by: Duke Xin <duke_xinanwen@163.com>
> Cc: stable@vger.kernel.org
> Signed-off-by: Johan Hovold <johan@kernel.org>
And I certainly have not signed-off on this yet. You must not add SoB
for anyone but yourself. Please review the process documentation for
what a SoB imply and how it is used, and try again.
> Signed-off-by: Duke Xin <duke_xinanwen@163.com>
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
* [PATCH] USB: serial: option: add Quectel EM05-G modem
@ 2022-06-20 12:16 Yonglin Tan
2022-06-20 12:57 ` Johan Hovold
0 siblings, 1 reply; 14+ messages in thread
From: Yonglin Tan @ 2022-06-20 12:16 UTC (permalink / raw)
To: johan; +Cc: linux-usb, linux-kernel, Yonglin Tan
Add a device-id entry for the Quectel EM05-G module.
T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
P: Vendor=2c7c ProdID=030a Rev= 3.18
S: Manufacturer=Quectel
S: Product=Quectel EM05-G
C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Signed-off-by: Yonglin Tan <yonglin.tan@outlook.com>
---
drivers/usb/serial/option.c | 2 ++
1 file changed, 2 insertions(+)
mode change 100644 => 100755 drivers/usb/serial/option.c
diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
old mode 100644
new mode 100755
index ed1e50d..05fc322
--- a/drivers/usb/serial/option.c
+++ b/drivers/usb/serial/option.c
@@ -1147,6 +1147,8 @@ static const struct usb_device_id option_ids[] = {
.driver_info = ZLP },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
{ USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
+ { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x030a, 0xff),
+ .driver_info = RSVD(6) | ZLP }, /* EM05-G */
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
{ USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
--
2.7.4
^ permalink raw reply [flat|nested] 14+ messages in thread* Re: [PATCH] USB: serial: option: add Quectel EM05-G modem
2022-06-20 12:16 Yonglin Tan
@ 2022-06-20 12:57 ` Johan Hovold
0 siblings, 0 replies; 14+ messages in thread
From: Johan Hovold @ 2022-06-20 12:57 UTC (permalink / raw)
To: Yonglin Tan; +Cc: linux-usb, linux-kernel
On Mon, Jun 20, 2022 at 08:16:53PM +0800, Yonglin Tan wrote:
> Add a device-id entry for the Quectel EM05-G module.
>
> T: Bus=01 Lev=01 Prnt=01 Port=00 Cnt=01 Dev#= 16 Spd=480 MxCh= 0
> D: Ver= 2.00 Cls=ef(misc ) Sub=02 Prot=01 MxPS=64 #Cfgs= 1
> P: Vendor=2c7c ProdID=030a Rev= 3.18
> S: Manufacturer=Quectel
> S: Product=Quectel EM05-G
> C:* #Ifs= 6 Cfg#= 1 Atr=a0 MxPwr=500mA
> A: FirstIf#= 0 IfCount= 2 Cls=02(comm.) Sub=0e Prot=00
> I:* If#= 3 Alt= 0 #EPs= 2 Cls=ff(vend.) Sub=ff Prot=ff Driver=option
> E: Ad=81(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=01(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 4 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=83(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=82(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=02(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 2 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=85(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=84(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=03(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 5 Alt= 0 #EPs= 3 Cls=ff(vend.) Sub=00 Prot=00 Driver=option
> E: Ad=87(I) Atr=03(Int.) MxPS= 10 Ivl=32ms
> E: Ad=86(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=04(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> I:* If#= 0 Alt= 0 #EPs= 1 Cls=02(comm.) Sub=0e Prot=00 Driver=cdc_mbim
> E: Ad=89(I) Atr=03(Int.) MxPS= 64 Ivl=32ms
> I: If#= 1 Alt= 0 #EPs= 0 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> I:* If#= 1 Alt= 1 #EPs= 2 Cls=0a(data ) Sub=00 Prot=02 Driver=cdc_mbim
> E: Ad=88(I) Atr=02(Bulk) MxPS= 512 Ivl=0ms
> E: Ad=05(O) Atr=02(Bulk) MxPS= 512 Ivl=0ms
Are there any further configurations for this device that you need to
consider?
You reserve interface 6 below which doesn't even exist in the above
configuration.
Can you say something more about what the individual interfaces are used
for, for example, as was done here:
https://lore.kernel.org/all/TYZPR06MB4270D3394B8E3E0301738F6B86D09@TYZPR06MB4270.apcprd06.prod.outlook.com/
> Signed-off-by: Yonglin Tan <yonglin.tan@outlook.com>
> ---
> drivers/usb/serial/option.c | 2 ++
> 1 file changed, 2 insertions(+)
> mode change 100644 => 100755 drivers/usb/serial/option.c
>
> diff --git a/drivers/usb/serial/option.c b/drivers/usb/serial/option.c
> old mode 100644
> new mode 100755
> index ed1e50d..05fc322
> --- a/drivers/usb/serial/option.c
> +++ b/drivers/usb/serial/option.c
> @@ -1147,6 +1147,8 @@ static const struct usb_device_id option_ids[] = {
> .driver_info = ZLP },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200S_CN, 0xff, 0, 0) },
> { USB_DEVICE_AND_INTERFACE_INFO(QUECTEL_VENDOR_ID, QUECTEL_PRODUCT_EC200T, 0xff, 0, 0) },
> + { USB_DEVICE_INTERFACE_CLASS(QUECTEL_VENDOR_ID, 0x030a, 0xff),
> + .driver_info = RSVD(6) | ZLP }, /* EM05-G */
As mentioned above RSVD(6) looks wrong here.
Please move the comment to the first line of the entry, and move the
entry to the other Quectel entries using numerical PIDs (i.e. before
EM160R-GL).
> { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_6001) },
> { USB_DEVICE(CMOTECH_VENDOR_ID, CMOTECH_PRODUCT_CMU_300) },
Johan
^ permalink raw reply [flat|nested] 14+ messages in thread
end of thread, other threads:[~2023-01-12 17:19 UTC | newest]
Thread overview: 14+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2022-11-16 5:25 [PATCH] USB: serial: option: add Quectel EM05-G modem Duke Xin
2022-11-16 6:01 ` Greg KH
-- strict thread matches above, loose matches on Subject: below --
2022-12-27 9:51 Duke Xin(辛安文)
2023-01-12 16:48 ` Johan Hovold
2022-12-27 9:44 Duke Xin(辛安文)
2022-12-27 9:28 Duke Xin(辛安文)
2023-01-12 16:36 ` Johan Hovold
2022-11-19 9:44 Duke Xin
2022-11-25 9:26 ` Johan Hovold
[not found] <20221116105554.329246-1-duke_xinanwen@163.com>
2022-11-16 11:31 ` Greg KH
2022-11-11 3:56 Duke Xin
2022-11-15 10:04 ` Johan Hovold
2022-06-20 12:16 Yonglin Tan
2022-06-20 12:57 ` Johan Hovold
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®