[PATCH v2 0/3] ARM: dts: qcom: msm8926-motorola-peregrine: Update device tree of Motorola Moto G 4G (2013)

[PATCH v2 0/3] ARM: dts: qcom: msm8926-motorola-peregrine: Update device tree of Motorola Moto G 4G (2013)

[André Apitzsch via B4 Relay]

Add accelerometer, magnetometer, regulator and temperature sensor alert
interrupt and update framebuffer supplies.

Signed-off-by: André Apitzsch <git@apitzsch.eu>
---
Changes in v2:
- Split commit into three commits
- Link to v1: https://lore.kernel.org/r/20240616-peregrine-v1-1-85d14ae1a11a@apitzsch.eu

---
André Apitzsch (3):
      ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator
      ARM: dts: qcom: msm8926-motorola-peregrine: Update temperature sensor
      ARM: dts: qcom: msm8926-motorola-peregrine: Add framebuffer supplies

 .../dts/qcom/qcom-msm8926-motorola-peregrine.dts   | 121 +++++++++++++++++++++
 1 file changed, 121 insertions(+)
---
base-commit: c71189547381bb5f176c6b22a9edc3414f1837b9
change-id: 20240616-peregrine-6ec5e26b15ec

Best regards,
-- 
André Apitzsch <git@apitzsch.eu>

[PATCH v2 1/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator

[André Apitzsch via B4 Relay]

From: André Apitzsch <git@apitzsch.eu>

Add the accelerometer, magnetometer and regulator that are present on
the Motorola Moto G 4G (2013) device.

Signed-off-by: André Apitzsch <git@apitzsch.eu>
---
 .../dts/qcom/qcom-msm8926-motorola-peregrine.dts   | 85 ++++++++++++++++++++++
 1 file changed, 85 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
index 0cbe2d2fbbb1..50ae3cfc95bb 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -68,9 +68,60 @@ smem_region: smem@fa00000 {
 	};
 };
 
+&blsp1_i2c2 {
+	clock-frequency = <100000>;
+	status = "okay";
+
+	magnetometer@c {
+		compatible = "asahi-kasei,ak8963";
+		reg = <0xc>;
+		interrupts-extended = <&tlmm 38 IRQ_TYPE_EDGE_FALLING>;
+		reset-gpios = <&tlmm 62 GPIO_ACTIVE_LOW>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&mag_int_default &mag_reset_default>;
+		pinctrl-names = "default";
+	};
+
+	accelerometer@18 {
+		compatible = "st,lis3dh-accel";
+		reg = <0x18>;
+		interrupts-extended = <&tlmm 1 IRQ_TYPE_EDGE_FALLING>;
+		vdd-supply = <&pm8226_l19>;
+		pinctrl-0 = <&accel_int_default>;
+		pinctrl-names = "default";
+		st,drdy-int-pin = <1>;
+	};
+};
+
 &blsp1_i2c3 {
+	clock-frequency = <400000>;
 	status = "okay";
 
+	regulator@3e {
+		compatible = "ti,tps65132";
+		reg = <0x3e>;
+		pinctrl-0 = <&reg_lcd_default>;
+		pinctrl-names = "default";
+
+		reg_lcd_pos: outp {
+			regulator-name = "outp";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		};
+
+		reg_lcd_neg: outn {
+			regulator-name = "outn";
+			regulator-min-microvolt = <4000000>;
+			regulator-max-microvolt = <6000000>;
+			regulator-active-discharge = <1>;
+			regulator-boot-on;
+			enable-gpios = <&tlmm 33 GPIO_ACTIVE_HIGH>;
+		};
+	};
+
 	sensor@48 {
 		compatible = "ti,tmp108";
 		reg = <0x48>;
@@ -278,6 +329,40 @@ &smbb {
 	status = "okay";
 };
 
+&tlmm {
+	accel_int_default: accel-int-default-state {
+		pins = "gpio1";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_int_default: mag-int-default-state {
+		pins = "gpio38";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
+
+	mag_reset_default: mag-reset-default-state {
+		pins = "gpio62";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
+	reg_lcd_default: reg-lcd-default-state {
+		pins = "gpio31", "gpio33";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+};
+
 &usb {
 	extcon = <&smbb>;
 	dr_mode = "peripheral";

-- 
2.45.2

Re: [PATCH v2 1/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator

[Konrad Dybcio]

On 6/17/24 23:22, André Apitzsch via B4 Relay wrote:
> From: André Apitzsch <git@apitzsch.eu>
> 
> Add the accelerometer, magnetometer and regulator that are present on
> the Motorola Moto G 4G (2013) device.
> 
> Signed-off-by: André Apitzsch <git@apitzsch.eu>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

[PATCH v2 2/3] ARM: dts: qcom: msm8926-motorola-peregrine: Update temperature sensor

[André Apitzsch via B4 Relay]

From: André Apitzsch <git@apitzsch.eu>

Add alert interrupt for the temperature sensor of Motorola Moto G 4G
(2013), although not used by the driver yet.

Signed-off-by: André Apitzsch <git@apitzsch.eu>
---
 arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts | 12 ++++++++++++
 1 file changed, 12 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
index 50ae3cfc95bb..cff9415baa46 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -125,6 +125,10 @@ reg_lcd_neg: outn {
 	sensor@48 {
 		compatible = "ti,tmp108";
 		reg = <0x48>;
+		interrupts-extended = <&tlmm 13 IRQ_TYPE_LEVEL_LOW>;
+		pinctrl-0 = <&temp_alert_default>;
+		pinctrl-names = "default";
+		#thermal-sensor-cells = <0>;
 	};
 };
 
@@ -361,6 +365,14 @@ reg_lcd_default: reg-lcd-default-state {
 		bias-disable;
 		output-high;
 	};
+
+	temp_alert_default: temp-alert-default-state {
+		pins = "gpio13";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-disable;
+	};
 };
 
 &usb {

-- 
2.45.2

Re: [PATCH v2 2/3] ARM: dts: qcom: msm8926-motorola-peregrine: Update temperature sensor

[Konrad Dybcio]

On 6/17/24 23:22, André Apitzsch via B4 Relay wrote:
> From: André Apitzsch <git@apitzsch.eu>
> 
> Add alert interrupt for the temperature sensor of Motorola Moto G 4G
> (2013), although not used by the driver yet.
> 
> Signed-off-by: André Apitzsch <git@apitzsch.eu>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

[PATCH v2 3/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add framebuffer supplies

[André Apitzsch via B4 Relay]

From: André Apitzsch <git@apitzsch.eu>

Add regulators used by the framebuffer of Motorola Moto G 4G (2013).

Signed-off-by: André Apitzsch <git@apitzsch.eu>
---
 .../dts/qcom/qcom-msm8926-motorola-peregrine.dts   | 24 ++++++++++++++++++++++
 1 file changed, 24 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
index cff9415baa46..376a33125941 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-motorola-peregrine.dts
@@ -29,6 +29,10 @@ framebuffer0: framebuffer@3200000 {
 			height = <1280>;
 			stride = <(720 * 3)>;
 			format = "r8g8b8";
+			vsp-supply = <&reg_lcd_pos>;
+			vsn-supply = <&reg_lcd_neg>;
+			vdd-supply = <&pm8226_l28>;
+			vddio-supply = <&vddio_disp_vreg>;
 		};
 	};
 
@@ -51,6 +55,18 @@ key-volume-up {
 		};
 	};
 
+	vddio_disp_vreg: regulator-vddio-disp {
+		compatible = "regulator-fixed";
+		regulator-name = "vddio_disp";
+		gpio = <&tlmm 34 GPIO_ACTIVE_HIGH>;
+		startup-delay-us = <300>;
+		enable-active-high;
+		regulator-boot-on;
+		vin-supply = <&pm8226_l8>;
+		pinctrl-0 = <&disp_vddio_default>;
+		pinctrl-names = "default";
+	};
+
 	reserved-memory {
 		#address-cells = <1>;
 		#size-cells = <1>;
@@ -342,6 +358,14 @@ accel_int_default: accel-int-default-state {
 		output-disable;
 	};
 
+	disp_vddio_default: disp-vddio-default-state {
+		pins = "gpio34";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-high;
+	};
+
 	mag_int_default: mag-int-default-state {
 		pins = "gpio38";
 		function = "gpio";

-- 
2.45.2

Re: [PATCH v2 3/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add framebuffer supplies

[Konrad Dybcio]

On 6/17/24 23:22, André Apitzsch via B4 Relay wrote:
> From: André Apitzsch <git@apitzsch.eu>
> 
> Add regulators used by the framebuffer of Motorola Moto G 4G (2013).
> 
> Signed-off-by: André Apitzsch <git@apitzsch.eu>
> ---

Reviewed-by: Konrad Dybcio <konrad.dybcio@linaro.org>

Konrad

Re: [PATCH v2 0/3] ARM: dts: qcom: msm8926-motorola-peregrine: Update device tree of Motorola Moto G 4G (2013)

[Bjorn Andersson]

On Mon, 17 Jun 2024 23:22:26 +0200, André Apitzsch wrote:
> Add accelerometer, magnetometer, regulator and temperature sensor alert
> interrupt and update framebuffer supplies.
> 
> 

Applied, thanks!

[1/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add accelerometer, magnetometer, regulator
      commit: 65ec35baeb937e91970c5d88118c5638d8582bb3
[2/3] ARM: dts: qcom: msm8926-motorola-peregrine: Update temperature sensor
      commit: c9c86387ea1c4034fec34690c7cf2a96f9c21196
[3/3] ARM: dts: qcom: msm8926-motorola-peregrine: Add framebuffer supplies
      commit: fed1c79fc7fe10900d99a79a36e40443f3267ef3

Best regards,
-- 
Bjorn Andersson <andersson@kernel.org>