[PATCH 0/3] i2c: Add driver support Amlogic A9 I2C

[PATCH 0/3] i2c: Add driver support Amlogic A9 I2C

[Xianwei Zhao via B4 Relay]

Add a Device Tree binding and driver for the I2C controller found on the
Amlogic A9 SoC.

Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
Junyi Zhao (1):
      i2c: amlogic: Add Amlogic A9 I2C controller driver

Xianwei Zhao (2):
      dt-bindings: i2c: add Amlogic A9 I2C controller
      MAINTAINERS: Add an entry for Amlogic I2C driver

 .../devicetree/bindings/i2c/amlogic,a9-i2c.yaml    |  61 +++
 MAINTAINERS                                        |   8 +
 drivers/i2c/busses/Kconfig                         |   9 +
 drivers/i2c/busses/Makefile                        |   1 +
 drivers/i2c/busses/i2c-amlogic-a9.c                | 504 +++++++++++++++++++++
 5 files changed, 583 insertions(+)
---
base-commit: e817a366cd24ddc8f986ef43c5d54cc3f60b0c21
change-id: 20260911-a9-i2c-24478e22e683

Best regards,
-- 
Xianwei Zhao <xianwei.zhao@amlogic.com>

[PATCH 1/3] dt-bindings: i2c: add Amlogic A9 I2C controller

[Xianwei Zhao via B4 Relay]

From: Xianwei Zhao <xianwei.zhao@amlogic.com>

Add a Device Tree binding for the I2C controller found on the
Amlogic A9 SoC.

Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
 .../devicetree/bindings/i2c/amlogic,a9-i2c.yaml    | 61 ++++++++++++++++++++++
 1 file changed, 61 insertions(+)

diff --git a/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml b/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
new file mode 100644
index 000000000000..681241a52680
--- /dev/null
+++ b/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
@@ -0,0 +1,61 @@
+# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/i2c/amlogic,a9-i2c.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Amlogic A9 I2C Controller
+
+maintainers:
+  - Xianwei Zhao <xianwei.zhaol@amlogic.com>
+  - Junyi Zhao <junyi.zhaol@amlogic.com>
+
+allOf:
+  - $ref: /schemas/i2c/i2c-controller.yaml#
+
+properties:
+  compatible:
+    const: amlogic,a9-i2c
+
+  reg:
+    maxItems: 1
+
+  interrupts:
+    maxItems: 1
+
+  clocks:
+    maxItems: 1
+
+  dmas:
+    items:
+      - description: DMA controller phandle and request line for RX
+      - description: DMA controller phandle and request line for TX
+
+  dma-names:
+    items:
+      - const: rx
+      - const: tx
+
+required:
+  - compatible
+  - reg
+  - interrupts
+  - clocks
+
+unevaluatedProperties: false
+
+examples:
+  - |
+    i2c@3a4400 {
+        compatible = "amlogic,a9-i2c";
+        reg = <0x3a4400 0x3c>;
+        interrupts = <1 164 1>;
+        clocks = <&clkc_periphs 11>;
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        eeprom@52 {
+            compatible = "atmel,24c32";
+            reg = <0x52>;
+        };
+    };

-- 
2.52.0

Re: [PATCH 1/3] dt-bindings: i2c: add Amlogic A9 I2C controller

[Conor Dooley]

[-- Attachment #1: Type: text/plain, Size: 2373 bytes --]

On Thu, Sep 24, 2026 at 08:39:34AM +0000, Xianwei Zhao via B4 Relay wrote:
> From: Xianwei Zhao <xianwei.zhao@amlogic.com>
> 
> Add a Device Tree binding for the I2C controller found on the
> Amlogic A9 SoC.
> 
> Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>

Since this is not in the existing meson file, does that mean that
there's a substantial change in the IP design, other than the addition
of dma support?

> ---
>  .../devicetree/bindings/i2c/amlogic,a9-i2c.yaml    | 61 ++++++++++++++++++++++
>  1 file changed, 61 insertions(+)
> 
> diff --git a/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml b/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
> new file mode 100644
> index 000000000000..681241a52680
> --- /dev/null
> +++ b/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
> @@ -0,0 +1,61 @@
> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
> +%YAML 1.2
> +---
> +$id: http://devicetree.org/schemas/i2c/amlogic,a9-i2c.yaml#
> +$schema: http://devicetree.org/meta-schemas/core.yaml#
> +
> +title: Amlogic A9 I2C Controller
> +
> +maintainers:
> +  - Xianwei Zhao <xianwei.zhaol@amlogic.com>
> +  - Junyi Zhao <junyi.zhaol@amlogic.com>
> +
> +allOf:
> +  - $ref: /schemas/i2c/i2c-controller.yaml#
> +
> +properties:
> +  compatible:
> +    const: amlogic,a9-i2c
> +
> +  reg:
> +    maxItems: 1
> +
> +  interrupts:
> +    maxItems: 1
> +
> +  clocks:
> +    maxItems: 1
> +
> +  dmas:
> +    items:
> +      - description: DMA controller phandle and request line for RX
> +      - description: DMA controller phandle and request line for TX
> +
> +  dma-names:
> +    items:
> +      - const: rx
> +      - const: tx
> +
> +required:
> +  - compatible
> +  - reg
> +  - interrupts
> +  - clocks
> +
> +unevaluatedProperties: false
> +
> +examples:
> +  - |
> +    i2c@3a4400 {
> +        compatible = "amlogic,a9-i2c";
> +        reg = <0x3a4400 0x3c>;
> +        interrupts = <1 164 1>;
> +        clocks = <&clkc_periphs 11>;
> +        #address-cells = <1>;
> +        #size-cells = <0>;
> +

> +        eeprom@52 {
> +            compatible = "atmel,24c32";
> +            reg = <0x52>;
> +        };

Remove this from your example please.
pw-bot: changes-requested

Thanks,
Conor.

> +    };
> 
> -- 
> 2.52.0
> 
> 

[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 228 bytes --]

Re: [PATCH 1/3] dt-bindings: i2c: add Amlogic A9 I2C controller

[Xianwei Zhao]

Hi Conor,
    Thanks for your review.

On 2026/9/25 01:01, Conor Dooley wrote:
> Subject:
> Re: [PATCH 1/3] dt-bindings: i2c: add Amlogic A9 I2C controller
> From:
> Conor Dooley <conor@kernel.org>
> Date:
> 2026/9/25 01:01
> 
> To:
> xianwei.zhao@amlogic.com
> CC:
> Junyi Zhao <junyi.zhao@amlogic.com>, Andi Shyti <andi.shyti@kernel.org>, 
> Rob Herring <robh@kernel.org>, Krzysztof Kozlowski <krzk+dt@kernel.org>, 
> Conor Dooley <conor+dt@kernel.org>, Xianwei Zhao 
> <xianwei.zhaol@amlogic.com>, Junyi Zhao <junyi.zhaol@amlogic.com>, 
> linux-i2c@vger.kernel.org, linux-amlogic@lists.infradead.org, 
> devicetree@vger.kernel.org, linux-kernel@vger.kernel.org
> 
> 
> On Thu, Sep 24, 2026 at 08:39:34AM +0000, Xianwei Zhao via B4 Relay wrote:
>> From: Xianwei Zhao<xianwei.zhao@amlogic.com>
>>
>> Add a Device Tree binding for the I2C controller found on the
>> Amlogic A9 SoC.
>>
>> Signed-off-by: Xianwei Zhao<xianwei.zhao@amlogic.com>
> Since this is not in the existing meson file, does that mean that
> there's a substantial change in the IP design, other than the addition
> of dma support?
> 

Yes. This is a new I2C controller that is different from the existing one.

>> ---
>>   .../devicetree/bindings/i2c/amlogic,a9-i2c.yaml    | 61 ++++++++++++++++++++++
>>   1 file changed, 61 insertions(+)
>>
>> diff --git a/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml b/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
>> new file mode 100644
>> index 000000000000..681241a52680
>> --- /dev/null
>> +++ b/Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
>> @@ -0,0 +1,61 @@
>> +# SPDX-License-Identifier: (GPL-2.0 OR BSD-2-Clause)
>> +%YAML 1.2
>> +---
>> +$id:http://devicetree.org/schemas/i2c/amlogic,a9-i2c.yaml#
>> +$schema:http://devicetree.org/meta-schemas/core.yaml#
>> +
>> +title: Amlogic A9 I2C Controller
>> +
>> +maintainers:
>> +  - Xianwei Zhao<xianwei.zhaol@amlogic.com>
>> +  - Junyi Zhao<junyi.zhaol@amlogic.com>
>> +
>> +allOf:
>> +  - $ref: /schemas/i2c/i2c-controller.yaml#
>> +
>> +properties:
>> +  compatible:
>> +    const: amlogic,a9-i2c
>> +
>> +  reg:
>> +    maxItems: 1
>> +
>> +  interrupts:
>> +    maxItems: 1
>> +
>> +  clocks:
>> +    maxItems: 1
>> +
>> +  dmas:
>> +    items:
>> +      - description: DMA controller phandle and request line for RX
>> +      - description: DMA controller phandle and request line for TX
>> +
>> +  dma-names:
>> +    items:
>> +      - const: rx
>> +      - const: tx
>> +
>> +required:
>> +  - compatible
>> +  - reg
>> +  - interrupts
>> +  - clocks
>> +
>> +unevaluatedProperties: false
>> +
>> +examples:
>> +  - |
>> +    i2c@3a4400 {
>> +        compatible = "amlogic,a9-i2c";
>> +        reg = <0x3a4400 0x3c>;
>> +        interrupts = <1 164 1>;
>> +        clocks = <&clkc_periphs 11>;
>> +        #address-cells = <1>;
>> +        #size-cells = <0>;
>> +
>> +        eeprom@52 {
>> +            compatible = "atmel,24c32";
>> +            reg = <0x52>;
>> +        };
> Remove this from your example please.

Will remove eeprom node from examples.

> pw-bot: changes-requested
> 
> Thanks,
> Conor.
> 
>> +    };
>>
>> -- 
>> 2.52.0
>>
>>

[PATCH 2/3] i2c: amlogic: Add Amlogic A9 I2C controller driver

[Xianwei Zhao via B4 Relay]

From: Junyi Zhao <junyi.zhao@amlogic.com>

Add support for the new I2C controller used by Amlogic A9 SoCs.

Add a dedicated Kconfig option and Makefile entry for the A9 I2C
controller driver.

Signed-off-by: Junyi Zhao <junyi.zhao@amlogic.com>
Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
 drivers/i2c/busses/Kconfig          |   9 +
 drivers/i2c/busses/Makefile         |   1 +
 drivers/i2c/busses/i2c-amlogic-a9.c | 504 ++++++++++++++++++++++++++++++++++++
 3 files changed, 514 insertions(+)

diff --git a/drivers/i2c/busses/Kconfig b/drivers/i2c/busses/Kconfig
index d7b89508311f..5595a5166569 100644
--- a/drivers/i2c/busses/Kconfig
+++ b/drivers/i2c/busses/Kconfig
@@ -885,6 +885,15 @@ config I2C_MESON
 	  If you say yes to this option, support will be included for the
 	  I2C interface on the Amlogic Meson family of SoCs.
 
+config I2C_AMLOGIC_A9
+	tristate "Amlogic new I2C controller"
+	depends on ARCH_MESON || COMPILE_TEST
+	depends on COMMON_CLK
+	help
+	  If you say yes to this option, support will be included for the
+	  I2C interface on the new Amlogic family of SoCs.
+
+
 config I2C_MICROCHIP_CORE
 	tristate "Microchip FPGA I2C controller"
 	depends on ARCH_MICROCHIP_POLARFIRE || COMPILE_TEST
diff --git a/drivers/i2c/busses/Makefile b/drivers/i2c/busses/Makefile
index 3755c54b3d82..9ffb1082b80b 100644
--- a/drivers/i2c/busses/Makefile
+++ b/drivers/i2c/busses/Makefile
@@ -82,6 +82,7 @@ obj-$(CONFIG_I2C_LPC2K)		+= i2c-lpc2k.o
 obj-$(CONFIG_I2C_LS2X)		+= i2c-ls2x.o
 obj-$(CONFIG_I2C_LS2X_V2)	+= i2c-ls2x-v2.o
 obj-$(CONFIG_I2C_MESON)		+= i2c-meson.o
+obj-$(CONFIG_I2C_AMLOGIC_A9)	+= i2c-amlogic-a9.o
 obj-$(CONFIG_I2C_MICROCHIP_CORE)	+= i2c-microchip-corei2c.o
 obj-$(CONFIG_I2C_MPC)		+= i2c-mpc.o
 obj-$(CONFIG_I2C_MT65XX)	+= i2c-mt65xx.o
diff --git a/drivers/i2c/busses/i2c-amlogic-a9.c b/drivers/i2c/busses/i2c-amlogic-a9.c
new file mode 100644
index 000000000000..2fcac7ee0e72
--- /dev/null
+++ b/drivers/i2c/busses/i2c-amlogic-a9.c
@@ -0,0 +1,504 @@
+// SPDX-License-Identifier: (GPL-2.0-only OR MIT)
+/*
+ * Copyright (C) 2026 Amlogic, Inc. All rights reserved
+ */
+
+#include <linux/clk.h>
+#include <linux/completion.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/of_device.h>
+#include <linux/platform_device.h>
+#include <linux/pinctrl/consumer.h>
+#include <linux/delay.h>
+
+/* Amlogic I2C register map */
+#define REG_CFG_RDY		0x00
+#define REG_CFG_I2C		0x04
+#define REG_CFG_START		0x08
+#define REG_CFG_BUS		0x0c
+#define REG_TX_RD_ADDR		0x10
+#define REG_TX_WR_ADDR		0x14
+#define REG_RX_RD_ADDR		0x18
+#define REG_RX_WR_ADDR		0x1c
+#define REG_CGF_TX		0x20
+#define REG_CGF_RX		0x24
+#define REG_CGF_IRQ_STATE	0x30
+#define REG_CGF_IRQ_ENABLE	0x34
+#define REG_SHAKE_BLK_CNT	0x38
+
+/* CFG RDY fields */
+#define RDY_TEE_ONLY		BIT(1)
+#define RDY_IF			BIT(0)
+
+/* CFG I2C fields */
+#define I2C_RX_THR		GENMASK(23, 16)
+#define I2C_TX_THR		GENMASK(15, 8)
+
+/* CFG BUS fields */
+#define BUS_NO_STOP		BIT(18)
+#define BUS_SPEED_MODE		BIT(17)
+#define BUS_SLAVE_MODE		BIT(16)
+#define BUS_FILTER_MASK		GENMASK(15, 12)
+/* SCL = clk/b_ratio	if b_ratio<=8, SCL = clk/8 */
+#define BUS_RATIO_MASK		GENMASK(11, 0)
+
+/* CFG START fields */
+#define START_START		BIT(31)
+#define START_LEN		GENMASK(23, 12)
+#define START_LEN_SHIFT		12
+#define START_SLAVE_ADDR	GENMASK(10, 1)
+#define START_READ		BIT(0)
+
+/* CFG TX_RX fields */
+#define TX_RX_EMPTY		BIT(9)
+#define TX_RX_FULL		BIT(8)
+#define TX_RX_DATA		GENMASK(7, 0)
+
+/*CGF IRQ fields */
+#define IRQ_ALL_MASK		0xffff
+#define A9_NCK_ERROR		BIT(0)
+#define A9_RX_EMPTY		BIT(1)
+#define A9_RX_FULL		BIT(2)
+#define A9_TX_EMPTY		BIT(3)
+#define A9_TX_FULL		BIT(4)
+#define A9_RX_THRESH_READ	BIT(5)
+#define A9_TX_THRESH_WRITE	BIT(6)
+#define A9_PHY_DONE		BIT(7)
+#define A9_TASK_DONE		BIT(8)
+#define A9_ALL_DONE		BIT(9)
+
+#define A9_TRANS_DONE		(A9_PHY_DONE | A9_NCK_ERROR)
+#define A9_TRANS_ERROR		(A9_NCK_ERROR)
+#define A9_ENABLE_IRQ_BIT	(A9_NCK_ERROR | A9_PHY_DONE)
+#define THRESH_MODE		(A9_RX_THRESH_READ | A9_TX_THRESH_WRITE)
+
+#define A9_I2C_FIFO_DEPTH	32
+#define A9_I2C_HALF_FIFO	(A9_I2C_FIFO_DEPTH >> 1)
+
+#define I2C_TIMEOUT_MS		500
+
+enum {
+	STATE_IDLE,
+	STATE_READ,
+	STATE_WRITE,
+};
+
+enum fifo_fill_mode {
+	FIFO_FILL_FULL,
+	FIFO_FILL_HALF,
+};
+
+/**
+ * struct aml_i2c - Amlogic I2C device private data
+ *
+ * @adap:	I2C adapter instance
+ * @dev:	Pointer to device structure
+ * @regs:	Base address of the device memory mapped registers
+ * @clk:	Pointer to clock structure
+ * @msg:	Pointer to the current I2C message
+ * @state:	Current state in the driver state machine
+ * @count:	Number of bytes to be sent/received in current transfer
+ * @pos:	Current position in the send/receive buffer
+ * @error:	Flag set when an error is received
+ * @lock:	To avoid race conditions between irq handler and xfer code
+ * @done:	Completion used to wait for transfer termination
+ * @clk_rate:	Clock source rate of I2C module
+ * @frequency:	Operating frequency of I2C bus clock
+ */
+struct aml_i2c {
+	struct i2c_adapter	adap;
+	struct device		*dev;
+	void __iomem		*regs;
+	struct clk		*clk;
+
+	struct i2c_msg		*msg;
+	int			state;
+	int			count;
+	int			pos;
+	int			error;
+	/* protect reg access */
+	spinlock_t		lock;
+	struct completion	done;
+	unsigned long		clk_rate;
+	unsigned int		frequency;
+};
+
+static void aml_i2c_set_mask(struct aml_i2c *i2c, int reg, u32 mask, u32 val)
+{
+	u32 data;
+
+	data = readl(i2c->regs + reg);
+	data &= ~mask;
+	data |= val & mask;
+	writel(data, i2c->regs + reg);
+}
+
+/*
+ * SCL = clk/b_ratio. if b_ratio<=8, SCL = clk/8
+ */
+static int aml_i2c_set_clk_div(struct aml_i2c *i2c)
+{
+	unsigned long clk_rate = i2c->clk_rate;
+	unsigned int div;
+
+	div = DIV_ROUND_UP(clk_rate, i2c->frequency);
+
+	/* clock divider has 12 bits */
+	if (div >= (1 << 12)) {
+		dev_err(i2c->dev, "requested bus frequency too low\n");
+		return -EINVAL;
+	} else if (div <= 8) {
+		dev_err(i2c->dev, "requested bus frequency too high\n");
+		return -EINVAL;
+	}
+	/* CFG_BUS reg:11 - 0 bits
+	 */
+	aml_i2c_set_mask(i2c, REG_CFG_BUS, BUS_RATIO_MASK, div);
+
+	return 0;
+}
+
+static void reset_fifo_pos(struct aml_i2c *i2c)
+{
+	writel(0x00, i2c->regs + REG_TX_RD_ADDR);
+	writel(0x00, i2c->regs + REG_TX_WR_ADDR);
+	writel(0x00, i2c->regs + REG_RX_WR_ADDR);
+	writel(0x00, i2c->regs + REG_RX_RD_ADDR);
+}
+
+static int controller_is_error(struct aml_i2c *i2c)
+{
+	int ret = 0;
+
+	if (readl(i2c->regs + REG_CGF_IRQ_STATE) & A9_TRANS_ERROR)
+		ret = -ENXIO;
+
+	return ret;
+}
+
+static int controller_is_done(struct aml_i2c *i2c)
+{
+	return readl(i2c->regs + REG_CGF_IRQ_STATE) & A9_TRANS_DONE;
+}
+
+static void clear_irq_status(struct aml_i2c *i2c, u32 irq_bits)
+{
+	writel(irq_bits, i2c->regs + REG_CGF_IRQ_STATE);
+}
+
+static int aml_i2c_init(struct aml_i2c *i2c)
+{
+	int ret;
+
+	clear_irq_status(i2c, IRQ_ALL_MASK);
+	writel(A9_ENABLE_IRQ_BIT, i2c->regs + REG_CGF_IRQ_ENABLE);
+	aml_i2c_set_mask(i2c, REG_CFG_BUS, BUS_NO_STOP, BUS_NO_STOP);
+	aml_i2c_set_mask(i2c, REG_CFG_I2C, I2C_RX_THR | I2C_TX_THR,
+			 A9_I2C_FIFO_DEPTH << 16 | A9_I2C_HALF_FIFO << 8);
+	reset_fifo_pos(i2c);
+	ret = aml_i2c_set_clk_div(i2c);
+
+	return ret;
+}
+
+static void aml_i2c_add_stop(struct aml_i2c *i2c)
+{
+	aml_i2c_set_mask(i2c, REG_CFG_BUS, BUS_NO_STOP, 0);
+}
+
+static void aml_i2c_cpy_data_to_user(struct aml_i2c *i2c, u8 data)
+{
+	u8 *buf = i2c->msg->buf + i2c->pos;
+
+	i2c->count = 1;
+	*buf = data;
+}
+
+static void aml_i2c_put_data(struct aml_i2c *i2c, char *buf, int len)
+{
+	int i;
+
+	/* this i2c module when trans 0 byte, must put at least 1.
+	 */
+	if (!i2c->msg->len) {
+		writel(0x00, i2c->regs + REG_CGF_TX);
+		return;
+	}
+
+	for (i = 0; i < len; i++, buf++)
+		writel(*buf, i2c->regs + REG_CGF_TX);
+}
+
+static void aml_i2c_prepare_xfer(struct aml_i2c *i2c, enum fifo_fill_mode mode)
+{
+	bool write = !(i2c->msg->flags & I2C_M_RD);
+
+	if (write) {
+		if (mode == FIFO_FILL_FULL)
+			i2c->count = min(i2c->msg->len - i2c->pos, A9_I2C_FIFO_DEPTH);
+		else
+			i2c->count = min(i2c->msg->len - i2c->pos, A9_I2C_HALF_FIFO);
+		aml_i2c_put_data(i2c, i2c->msg->buf + i2c->pos, i2c->count);
+	}
+}
+
+static irqreturn_t aml_i2c_irq(int irqno, void *dev_id)
+{
+	struct aml_i2c *i2c = dev_id;
+	int ret;
+	u32 rd_len, i;
+	u32 rd_val;
+
+	spin_lock(&i2c->lock);
+	ret = controller_is_error(i2c);
+	if (ret) {
+		i2c->error = ret;
+		goto complete_irq_out;
+	}
+
+	switch (i2c->state) {
+	case STATE_READ:
+		rd_len = min(i2c->msg->len - i2c->pos, A9_I2C_FIFO_DEPTH);
+		for (i = 0; i < rd_len; i++) {
+			rd_val = readl(i2c->regs + REG_CGF_RX);
+			aml_i2c_cpy_data_to_user(i2c, rd_val & TX_RX_DATA);
+			i2c->pos += i2c->count;
+		}
+		/* rx must clear thresh after read fifo */
+		clear_irq_status(i2c, A9_RX_THRESH_READ);
+		break;
+	case STATE_WRITE:
+		aml_i2c_prepare_xfer(i2c, FIFO_FILL_HALF);
+		if ((i2c->pos + A9_I2C_HALF_FIFO) >= i2c->msg->len)
+			aml_i2c_set_mask(i2c, REG_CGF_IRQ_ENABLE, A9_TX_THRESH_WRITE, 0);
+		/* tx must clear thresh after write fifo */
+		clear_irq_status(i2c, A9_TX_THRESH_WRITE);
+		i2c->pos += i2c->count;
+		break;
+	case STATE_IDLE:
+		dev_warn(i2c->dev, "i2c irq triggered abnormally!!!, irq_state:0x%x,irq_en:0x%x\n",
+			 readl(i2c->regs + REG_CGF_IRQ_STATE),
+			 readl(i2c->regs + REG_CGF_IRQ_ENABLE));
+		break;
+	default:
+		break;
+	}
+
+	if (!controller_is_done(i2c)) {
+		goto irq_trans_out;
+	} else {
+		if (i2c->state == STATE_READ && (i2c->msg->len - i2c->pos))
+			goto irq_trans_out;
+	}
+
+complete_irq_out:
+	reset_fifo_pos(i2c);
+	complete(&i2c->done);
+	i2c->state = STATE_IDLE;
+	aml_i2c_set_mask(i2c, REG_CGF_IRQ_ENABLE, A9_RX_THRESH_READ | A9_TX_THRESH_WRITE, 0);
+	clear_irq_status(i2c, IRQ_ALL_MASK);
+irq_trans_out:
+	spin_unlock(&i2c->lock);
+
+	return IRQ_HANDLED;
+}
+
+static void aml_i2c_do_start(struct aml_i2c *i2c, struct i2c_msg *msg)
+{
+	unsigned int reg_val;
+	unsigned int trans_len;
+
+	trans_len = msg->len;
+	reg_val = (unsigned int)((msg->addr << 1) |
+				((msg->flags & I2C_M_RD) ? START_READ : 0) |
+				((trans_len & 0xfff) << 12) | START_START);
+	aml_i2c_set_mask(i2c, REG_CFG_START,
+			 START_START | START_SLAVE_ADDR | START_READ | START_LEN, reg_val);
+	clear_irq_status(i2c, IRQ_ALL_MASK);
+	/* enable thresh mode */
+	if (trans_len > A9_I2C_FIFO_DEPTH) {
+		reg_val = (msg->flags & I2C_M_RD) ? A9_RX_THRESH_READ : A9_TX_THRESH_WRITE;
+		aml_i2c_set_mask(i2c, REG_CGF_IRQ_ENABLE,
+				 A9_RX_THRESH_READ | A9_TX_THRESH_WRITE, reg_val);
+	}
+}
+
+static int aml_i2c_xfer_msg(struct aml_i2c *i2c, struct i2c_msg *msg, bool last)
+{
+	unsigned long time_left, flags;
+	int ret = 0;
+
+	i2c->msg = msg;
+	i2c->pos = 0;
+	i2c->count = 0;
+	i2c->error = 0;
+
+	i2c->state = (msg->flags & I2C_M_RD) ? STATE_READ : STATE_WRITE;
+	aml_i2c_prepare_xfer(i2c, FIFO_FILL_FULL);
+	i2c->pos += i2c->count;
+	reinit_completion(&i2c->done);
+
+	if (last)
+		aml_i2c_add_stop(i2c);
+	/* Start the transfer */
+	aml_i2c_do_start(i2c, msg);
+
+	time_left = msecs_to_jiffies(I2C_TIMEOUT_MS);
+	time_left = wait_for_completion_timeout(&i2c->done, time_left);
+
+	/*
+	 * Protect access to i2c struct and registers from interrupt
+	 * handlers triggered by a transfer terminated after the
+	 * timeout period
+	 */
+	spin_lock_irqsave(&i2c->lock, flags);
+
+	if (!time_left) {
+		i2c->state = STATE_IDLE;
+		clear_irq_status(i2c, IRQ_ALL_MASK);
+		reset_fifo_pos(i2c);
+		ret = -ETIMEDOUT;
+	}
+
+	if (i2c->error)
+		ret = i2c->error;
+
+	spin_unlock_irqrestore(&i2c->lock, flags);
+
+	return ret;
+}
+
+static int aml_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
+{
+	struct aml_i2c *i2c = adap->algo_data;
+	int i, ret = 0;
+
+	for (i = 0; i < num; i++) {
+		ret = aml_i2c_xfer_msg(i2c, msgs + i, i == num - 1);
+		if (ret)
+			break;
+	}
+
+	return ret ?: i;
+}
+
+static u32 aml_i2c_func(struct i2c_adapter *adap)
+{
+	return I2C_FUNC_I2C | I2C_FUNC_SMBUS_EMUL;
+}
+
+static const struct i2c_algorithm aml_i2c_algorithm = {
+	.master_xfer	= aml_i2c_xfer,
+	.functionality	= aml_i2c_func,
+};
+
+static int aml_i2c_probe(struct platform_device *pdev)
+{
+	struct device_node *np = pdev->dev.of_node;
+	struct aml_i2c *i2c;
+	struct i2c_timings timings;
+	int irq, ret;
+
+	i2c = devm_kzalloc(&pdev->dev, sizeof(struct aml_i2c), GFP_KERNEL);
+	if (!i2c)
+		return -ENOMEM;
+
+	i2c_parse_fw_timings(&pdev->dev, &timings, true);
+	i2c->frequency = timings.bus_freq_hz;
+
+	i2c->dev = &pdev->dev;
+	platform_set_drvdata(pdev, i2c);
+
+	spin_lock_init(&i2c->lock);
+	init_completion(&i2c->done);
+
+	i2c->regs  = devm_platform_ioremap_resource(pdev, 0);
+	if (IS_ERR(i2c->regs))
+		return PTR_ERR(i2c->regs);
+
+	i2c->clk = devm_clk_get(&pdev->dev, NULL);
+	if (IS_ERR(i2c->clk)) {
+		dev_err(&pdev->dev, "can't get device clock\n");
+		return PTR_ERR(i2c->clk);
+	}
+
+	i2c->clk_rate = clk_get_rate(i2c->clk);
+	if (i2c->clk_rate == 0) {
+		dev_err(&pdev->dev, "failed to get clk rate\n");
+		return -EINVAL;
+	}
+
+	ret = aml_i2c_init(i2c);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "fail init i2c\n");
+		return ret;
+	}
+
+	irq = platform_get_irq(pdev, 0);
+	if (irq < 0) {
+		dev_err(&pdev->dev, "can't find IRQ\n");
+		return irq;
+	}
+
+	ret = devm_request_irq(&pdev->dev, irq, aml_i2c_irq, 0, dev_name(&pdev->dev), i2c);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "can't request IRQ\n");
+		return ret;
+	}
+
+	ret = clk_prepare_enable(i2c->clk);
+	if (ret < 0) {
+		dev_err(&pdev->dev, "can't prepare clock\n");
+		return ret;
+	}
+
+	strscpy(i2c->adap.name, "Amlogic I2C adapter",
+		sizeof(i2c->adap.name));
+	i2c->adap.owner = THIS_MODULE;
+	i2c->adap.algo = &aml_i2c_algorithm;
+	i2c->adap.dev.parent = &pdev->dev;
+	i2c->adap.dev.of_node = np;
+	i2c->adap.algo_data = i2c;
+
+	ret = i2c_add_adapter(&i2c->adap);
+	if (ret < 0) {
+		clk_disable_unprepare(i2c->clk);
+		return ret;
+	}
+
+	return 0;
+}
+
+static void aml_i2c_remove(struct platform_device *pdev)
+{
+	struct aml_i2c *i2c = platform_get_drvdata(pdev);
+
+	i2c_del_adapter(&i2c->adap);
+	clk_disable_unprepare(i2c->clk);
+}
+
+static const struct of_device_id aml_i2c_match[] = {
+	{	.compatible = "amlogic,a9-i2c",},
+	{ }
+};
+
+MODULE_DEVICE_TABLE(of, aml_i2c_match);
+
+static struct platform_driver aml_i2c_driver = {
+	.probe   = aml_i2c_probe,
+	.remove  = aml_i2c_remove,
+	.driver  = {
+		.name  = "amlogic-i2c",
+		.of_match_table = aml_i2c_match,
+	},
+};
+
+module_platform_driver(aml_i2c_driver);
+
+MODULE_DESCRIPTION("Amlogic I2C Bus driver");
+MODULE_AUTHOR("Junyi Zhao <junyi.zhao@amlogic.com>");
+MODULE_LICENSE("GPL");

-- 
2.52.0

Re: [PATCH 2/3] i2c: amlogic: Add Amlogic A9 I2C controller driver

[Andi Shyti]

Hi Xianwei,

...

> +config I2C_AMLOGIC_A9
> +	tristate "Amlogic new I2C controller"
> +	depends on ARCH_MESON || COMPILE_TEST
> +	depends on COMMON_CLK
> +	help
> +	  If you say yes to this option, support will be included for the
> +	  I2C interface on the new Amlogic family of SoCs.
> +
> +

Please, remove this extra line

>  config I2C_MICROCHIP_CORE
>  	tristate "Microchip FPGA I2C controller"
>  	depends on ARCH_MICROCHIP_POLARFIRE || COMPILE_TEST

...

> +#include <linux/clk.h>
> +#include <linux/completion.h>
> +#include <linux/i2c.h>
> +#include <linux/interrupt.h>
> +#include <linux/io.h>
> +#include <linux/module.h>
> +#include <linux/of.h>
> +#include <linux/of_device.h>
> +#include <linux/platform_device.h>
> +#include <linux/pinctrl/consumer.h>
> +#include <linux/delay.h>

Please sort the above in alphabetic order.

> +/* Amlogic I2C register map */
> +#define REG_CFG_RDY		0x00
> +#define REG_CFG_I2C		0x04
> +#define REG_CFG_START		0x08
> +#define REG_CFG_BUS		0x0c
> +#define REG_TX_RD_ADDR		0x10
> +#define REG_TX_WR_ADDR		0x14
> +#define REG_RX_RD_ADDR		0x18
> +#define REG_RX_WR_ADDR		0x1c
> +#define REG_CGF_TX		0x20
> +#define REG_CGF_RX		0x24
> +#define REG_CGF_IRQ_STATE	0x30
> +#define REG_CGF_IRQ_ENABLE	0x34
> +#define REG_SHAKE_BLK_CNT	0x38
> +
> +/* CFG RDY fields */
> +#define RDY_TEE_ONLY		BIT(1)
> +#define RDY_IF			BIT(0)
> +
> +/* CFG I2C fields */
> +#define I2C_RX_THR		GENMASK(23, 16)
> +#define I2C_TX_THR		GENMASK(15, 8)
> +
> +/* CFG BUS fields */
> +#define BUS_NO_STOP		BIT(18)
> +#define BUS_SPEED_MODE		BIT(17)
> +#define BUS_SLAVE_MODE		BIT(16)
> +#define BUS_FILTER_MASK		GENMASK(15, 12)
> +/* SCL = clk/b_ratio	if b_ratio<=8, SCL = clk/8 */
> +#define BUS_RATIO_MASK		GENMASK(11, 0)
> +
> +/* CFG START fields */
> +#define START_START		BIT(31)
> +#define START_LEN		GENMASK(23, 12)
> +#define START_LEN_SHIFT		12
> +#define START_SLAVE_ADDR	GENMASK(10, 1)
> +#define START_READ		BIT(0)
> +
> +/* CFG TX_RX fields */
> +#define TX_RX_EMPTY		BIT(9)
> +#define TX_RX_FULL		BIT(8)
> +#define TX_RX_DATA		GENMASK(7, 0)
> +
> +/*CGF IRQ fields */
> +#define IRQ_ALL_MASK		0xffff
> +#define A9_NCK_ERROR		BIT(0)
> +#define A9_RX_EMPTY		BIT(1)
> +#define A9_RX_FULL		BIT(2)
> +#define A9_TX_EMPTY		BIT(3)
> +#define A9_TX_FULL		BIT(4)
> +#define A9_RX_THRESH_READ	BIT(5)
> +#define A9_TX_THRESH_WRITE	BIT(6)
> +#define A9_PHY_DONE		BIT(7)
> +#define A9_TASK_DONE		BIT(8)
> +#define A9_ALL_DONE		BIT(9)
> +
> +#define A9_TRANS_DONE		(A9_PHY_DONE | A9_NCK_ERROR)
> +#define A9_TRANS_ERROR		(A9_NCK_ERROR)
> +#define A9_ENABLE_IRQ_BIT	(A9_NCK_ERROR | A9_PHY_DONE)
> +#define THRESH_MODE		(A9_RX_THRESH_READ | A9_TX_THRESH_WRITE)
> +
> +#define A9_I2C_FIFO_DEPTH	32
> +#define A9_I2C_HALF_FIFO	(A9_I2C_FIFO_DEPTH >> 1)
> +
> +#define I2C_TIMEOUT_MS		500
> +
> +enum {
> +	STATE_IDLE,
> +	STATE_READ,
> +	STATE_WRITE,
> +};
> +
> +enum fifo_fill_mode {
> +	FIFO_FILL_FULL,
> +	FIFO_FILL_HALF,
> +};

For all the enums and defines above, please use the prefix of the
driver name, A9, I guess.

...

> +static void aml_i2c_put_data(struct aml_i2c *i2c, char *buf, int len)
> +{
> +	int i;
> +
> +	/* this i2c module when trans 0 byte, must put at least 1.
> +	 */

Please use the kernel style commenting format, I think checkpatch
would have had raised this.

> +	if (!i2c->msg->len) {
> +		writel(0x00, i2c->regs + REG_CGF_TX);
> +		return;
> +	}
> +
> +	for (i = 0; i < len; i++, buf++)
> +		writel(*buf, i2c->regs + REG_CGF_TX);
> +}
> +
> +static void aml_i2c_prepare_xfer(struct aml_i2c *i2c, enum fifo_fill_mode mode)
> +{
> +	bool write = !(i2c->msg->flags & I2C_M_RD);
> +
> +	if (write) {

you can revert the logic here with if (!write) return; to save a
level of indentation.

> +		if (mode == FIFO_FILL_FULL)
> +			i2c->count = min(i2c->msg->len - i2c->pos, A9_I2C_FIFO_DEPTH);
> +		else
> +			i2c->count = min(i2c->msg->len - i2c->pos, A9_I2C_HALF_FIFO);
> +		aml_i2c_put_data(i2c, i2c->msg->buf + i2c->pos, i2c->count);
> +	}
> +}

...

> +static int aml_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
> +{
> +	struct aml_i2c *i2c = adap->algo_data;
> +	int i, ret = 0;
> +
> +	for (i = 0; i < num; i++) {
> +		ret = aml_i2c_xfer_msg(i2c, msgs + i, i == num - 1);
> +		if (ret)
> +			break;

you can save some code here by doing

	for (...) {
		int ret;

		ret = aml_i2c_xfer_msg(...);
		if (ret)
			return ret;
	}

	return i;

> +	}
> +
> +	return ret ?: i;
> +}

...

> +static int aml_i2c_probe(struct platform_device *pdev)
> +{
> +	struct device_node *np = pdev->dev.of_node;
> +	struct aml_i2c *i2c;

...

> +	i2c->clk = devm_clk_get(&pdev->dev, NULL);
> +	if (IS_ERR(i2c->clk)) {
> +		dev_err(&pdev->dev, "can't get device clock\n");
> +		return PTR_ERR(i2c->clk);
> +	}

Please use return dev_err_probe(...);

Andi

> +

Re: [PATCH 2/3] i2c: amlogic: Add Amlogic A9 I2C controller driver

[Xianwei Zhao]

Hi Andi,
    Thanks for your review.

On 2026/9/27 20:08, Andi Shyti wrote:
> Hi Xianwei,
> 
> ...
> 
>> +config I2C_AMLOGIC_A9
>> +     tristate "Amlogic new I2C controller"
>> +     depends on ARCH_MESON || COMPILE_TEST
>> +     depends on COMMON_CLK
>> +     help
>> +       If you say yes to this option, support will be included for the
>> +       I2C interface on the new Amlogic family of SoCs.
>> +
>> +
> Please, remove this extra line
>

Will do.

>>   config I2C_MICROCHIP_CORE
>>        tristate "Microchip FPGA I2C controller"
>>        depends on ARCH_MICROCHIP_POLARFIRE || COMPILE_TEST
> ...
> 
>> +#include <linux/clk.h>
>> +#include <linux/completion.h>
>> +#include <linux/i2c.h>
>> +#include <linux/interrupt.h>
>> +#include <linux/io.h>
>> +#include <linux/module.h>
>> +#include <linux/of.h>
>> +#include <linux/of_device.h>
>> +#include <linux/platform_device.h>
>> +#include <linux/pinctrl/consumer.h>
>> +#include <linux/delay.h>
> Please sort the above in alphabetic order.
> 

Will do.

>> +/* Amlogic I2C register map */
>> +#define REG_CFG_RDY          0x00
>> +#define REG_CFG_I2C          0x04
>> +#define REG_CFG_START                0x08
>> +#define REG_CFG_BUS          0x0c
>> +#define REG_TX_RD_ADDR               0x10
>> +#define REG_TX_WR_ADDR               0x14
>> +#define REG_RX_RD_ADDR               0x18
>> +#define REG_RX_WR_ADDR               0x1c
>> +#define REG_CGF_TX           0x20
>> +#define REG_CGF_RX           0x24
>> +#define REG_CGF_IRQ_STATE    0x30
>> +#define REG_CGF_IRQ_ENABLE   0x34
>> +#define REG_SHAKE_BLK_CNT    0x38
>> +
>> +/* CFG RDY fields */
>> +#define RDY_TEE_ONLY         BIT(1)
>> +#define RDY_IF                       BIT(0)
>> +
>> +/* CFG I2C fields */
>> +#define I2C_RX_THR           GENMASK(23, 16)
>> +#define I2C_TX_THR           GENMASK(15, 8)
>> +
>> +/* CFG BUS fields */
>> +#define BUS_NO_STOP          BIT(18)
>> +#define BUS_SPEED_MODE               BIT(17)
>> +#define BUS_SLAVE_MODE               BIT(16)
>> +#define BUS_FILTER_MASK              GENMASK(15, 12)
>> +/* SCL = clk/b_ratio if b_ratio<=8, SCL = clk/8 */
>> +#define BUS_RATIO_MASK               GENMASK(11, 0)
>> +
>> +/* CFG START fields */
>> +#define START_START          BIT(31)
>> +#define START_LEN            GENMASK(23, 12)
>> +#define START_LEN_SHIFT              12
>> +#define START_SLAVE_ADDR     GENMASK(10, 1)
>> +#define START_READ           BIT(0)
>> +
>> +/* CFG TX_RX fields */
>> +#define TX_RX_EMPTY          BIT(9)
>> +#define TX_RX_FULL           BIT(8)
>> +#define TX_RX_DATA           GENMASK(7, 0)
>> +
>> +/*CGF IRQ fields */
>> +#define IRQ_ALL_MASK         0xffff
>> +#define A9_NCK_ERROR         BIT(0)
>> +#define A9_RX_EMPTY          BIT(1)
>> +#define A9_RX_FULL           BIT(2)
>> +#define A9_TX_EMPTY          BIT(3)
>> +#define A9_TX_FULL           BIT(4)
>> +#define A9_RX_THRESH_READ    BIT(5)
>> +#define A9_TX_THRESH_WRITE   BIT(6)
>> +#define A9_PHY_DONE          BIT(7)
>> +#define A9_TASK_DONE         BIT(8)
>> +#define A9_ALL_DONE          BIT(9)
>> +
>> +#define A9_TRANS_DONE                (A9_PHY_DONE | A9_NCK_ERROR)
>> +#define A9_TRANS_ERROR               (A9_NCK_ERROR)
>> +#define A9_ENABLE_IRQ_BIT    (A9_NCK_ERROR | A9_PHY_DONE)
>> +#define THRESH_MODE          (A9_RX_THRESH_READ | A9_TX_THRESH_WRITE)
>> +
>> +#define A9_I2C_FIFO_DEPTH    32
>> +#define A9_I2C_HALF_FIFO     (A9_I2C_FIFO_DEPTH >> 1)
>> +
>> +#define I2C_TIMEOUT_MS               500
>> +
>> +enum {
>> +     STATE_IDLE,
>> +     STATE_READ,
>> +     STATE_WRITE,
>> +};
>> +
>> +enum fifo_fill_mode {
>> +     FIFO_FILL_FULL,
>> +     FIFO_FILL_HALF,
>> +};
> For all the enums and defines above, please use the prefix of the
> driver name, A9, I guess.
> 

Will add prefix A9

> ...
> 
>> +static void aml_i2c_put_data(struct aml_i2c *i2c, char *buf, int len)
>> +{
>> +     int i;
>> +
>> +     /* this i2c module when trans 0 byte, must put at least 1.
>> +      */
> Please use the kernel style commenting format, I think checkpatch
> would have had raised this.

Will do.

> 
>> +     if (!i2c->msg->len) {
>> +             writel(0x00, i2c->regs + REG_CGF_TX);
>> +             return;
>> +     }
>> +
>> +     for (i = 0; i < len; i++, buf++)
>> +             writel(*buf, i2c->regs + REG_CGF_TX);
>> +}
>> +
>> +static void aml_i2c_prepare_xfer(struct aml_i2c *i2c, enum fifo_fill_mode mode)
>> +{
>> +     bool write = !(i2c->msg->flags & I2C_M_RD);
>> +
>> +     if (write) {
> you can revert the logic here with if (!write) return; to save a
> level of indentation.
> 

Will do.

>> +             if (mode == FIFO_FILL_FULL)
>> +                     i2c->count = min(i2c->msg->len - i2c->pos, A9_I2C_FIFO_DEPTH);
>> +             else
>> +                     i2c->count = min(i2c->msg->len - i2c->pos, A9_I2C_HALF_FIFO);
>> +             aml_i2c_put_data(i2c, i2c->msg->buf + i2c->pos, i2c->count);
>> +     }
>> +}
> ...
> 
>> +static int aml_i2c_xfer(struct i2c_adapter *adap, struct i2c_msg *msgs, int num)
>> +{
>> +     struct aml_i2c *i2c = adap->algo_data;
>> +     int i, ret = 0;
>> +
>> +     for (i = 0; i < num; i++) {
>> +             ret = aml_i2c_xfer_msg(i2c, msgs + i, i == num - 1);
>> +             if (ret)
>> +                     break;
> you can save some code here by doing
> 
>          for (...) {
>                  int ret;
> 
>                  ret = aml_i2c_xfer_msg(...);
>                  if (ret)
>                          return ret;
>          }
> 
>          return i;
> 
Will do.
>> +     }
>> +
>> +     return ret ?: i;
>> +}
> ...
> 
>> +static int aml_i2c_probe(struct platform_device *pdev)
>> +{
>> +     struct device_node *np = pdev->dev.of_node;
>> +     struct aml_i2c *i2c;
> ...
> 
>> +     i2c->clk = devm_clk_get(&pdev->dev, NULL);
>> +     if (IS_ERR(i2c->clk)) {
>> +             dev_err(&pdev->dev, "can't get device clock\n");
>> +             return PTR_ERR(i2c->clk);
>> +     }
> Please use return dev_err_probe(...);
> 
Will do.
> Andi

[PATCH 3/3] MAINTAINERS: Add an entry for Amlogic I2C driver

[Xianwei Zhao via B4 Relay]

From: Xianwei Zhao <xianwei.zhao@amlogic.com>

Add Amlogic I2C controller entry to MAINTAINERS to clarify
the maintainers.

Signed-off-by: Xianwei Zhao <xianwei.zhao@amlogic.com>
---
 MAINTAINERS | 8 ++++++++
 1 file changed, 8 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 6215fcb07770..33c39ecf535f 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -1371,6 +1371,14 @@ F:	Documentation/devicetree/bindings/perf/amlogic,g12-ddr-pmu.yaml
 F:	drivers/perf/amlogic/
 F:	include/soc/amlogic/
 
+AMLOGIC I2C DRIVER
+M:	Junyi Zhao <junyi.zhao@amlogic.com>
+L:	linux-i2c@vger.kernel.org
+L:	linux-amlogic@lists.infradead.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/i2c/amlogic,a9-i2c.yaml
+F:	drivers/i2c/busses/i2c-amlogic-a9.c
+
 AMLOGIC ISP DRIVER
 M:	Keke Li <keke.li@amlogic.com>
 L:	linux-media@vger.kernel.org

-- 
2.52.0