[PATCH v2 0/8] Enable more nodes for the Xperia 10 III

[PATCH v2 0/8] Enable more nodes for the Xperia 10 III

[erebion]

Enable some more nodes for the Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
Changes in v2:
- Remove panel_reset_pin that shouldn't be part of this patch series
- Remove incorrect reg from mpss
- Fix conflicting bias pinctrl, as pinctrl nodes from sm6350.dtsi already contain a bias-* property
- Fix incorrect unit name in &pmk8350_vadc
- Link to v1: https://patch.msgid.link/20260926-pdx213-upstream-3-v1-0-1609c18b5c1d@erebion.eu

---
erebion (8):
      arm64: dts: qcom: sm6350-lena: Add flash LED
      arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node
      arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP & MPSS
      arm64: dts: qcom: sm6350-lena: Enable IPA
      arm64: dts: qcom: sm6350-lena: Enable Bluetooth
      arm64: dts: qcom: sm6350-lena: Enable wifi
      arm64: dts: qcom: sm6350-lena: Enable PM7250B
      arm64: dts: qcom: sm6350-lena: Enable PMK8350

 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 253 +++++++++++++++++++++
 1 file changed, 253 insertions(+)
---
base-commit: e5e04726cdd043e309677071ab1b65a4b18f422b
change-id: 20260829-pdx213-upstream-3-d0b80f749b5b

Best regards,
--  
erebion <erebion@erebion.eu>

[PATCH v2 1/8] arm64: dts: qcom: sm6350-lena: Add flash LED

[erebion]

Add a node for the camera flash LED found on the Xperia 10 III

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts      | 15 +++++++++++++++
 1 file changed, 15 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 6e2bbf4f060ac..79aa2521aed40 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,9 +4,11 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
 #include "sm6350.dtsi"
+#include "pm6150l.dtsi"
 #include "pm6350.dtsi"
 
 / {
@@ -302,6 +304,19 @@ touchscreen@48 {
 	};
 };
 
+&pm6150l_flash {
+	status = "okay";
+
+	led-0 {
+		function = LED_FUNCTION_FLASH;
+		color = <LED_COLOR_ID_WHITE>;
+		led-sources = <1>;
+		led-max-microamp = <180000>;
+		flash-max-microamp = <1000000>;
+		flash-max-timeout-us = <1280000>;
+	};
+};
+
 &pm6350_gpios {
 	vol_down_n: vol-down-n-state {
 		pins = "gpio2";

-- 
2.53.0

[PATCH v2 2/8] arm64: dts: qcom: sm6350-lena: Add qcom,rmtfs-mem node

[erebion]

Adds the qcom,rmtfs-mem node required for the modem

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 17 +++++++++++++++++
 1 file changed, 17 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 79aa2521aed40..0ef3e9e239786 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,6 +4,7 @@
  */
 /dts-v1/;
 
+#include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -54,6 +55,22 @@ touch_en_vreg: touch-en-regulator {
 
 		vin-supply = <&pm6350_l6>;
 	};
+
+	reserved-memory {
+		/*
+		 * The rmtfs memory region in downstream is 'dynamically allocated'
+		 * but given the same address every time. Hard code it as this address is
+		 * where the modem firmware expects it to be.
+		 */
+		rmtfs@fe901000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0 0xfe901000 0x0 0x280000>;
+			no-map;
+
+			qcom,client-id = <1>;
+			qcom,vmid = <QCOM_SCM_VMID_MSS_MSA>;
+		};
+	};
 };
 
 &apps_rsc {

-- 
2.53.0

[PATCH v2 3/8] arm64: dts: qcom: sm6350-lena: Enable ADSP, CDSP & MPSS

[erebion]

Enable the ADSP, CDSP and MPSS (Modem) nodes for the Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts   | 18 ++++++++++++++++++
 1 file changed, 18 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 0ef3e9e239786..c58047ce3291d 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -73,6 +73,12 @@ rmtfs@fe901000 {
 	};
 };
 
+&adsp {
+	firmware-name = "qcom/sm6350/sony/pdx213/adsp.mbn";
+
+	status = "okay";
+};
+
 &apps_rsc {
 	regulators-0 {
 		compatible = "qcom,pm6350-rpmh-regulators";
@@ -296,6 +302,12 @@ pm6150l_bob: bob {
 	};
 };
 
+&cdsp {
+	firmware-name = "qcom/sm6350/sony/pdx213/cdsp.mbn";
+
+	status = "okay";
+};
+
 &gpi_dma0 {
 	status = "okay";
 };
@@ -321,6 +333,12 @@ touchscreen@48 {
 	};
 };
 
+&mpss {
+	firmware-name = "qcom/sm6350/sony/pdx213/modem.mbn";
+
+	status = "okay";
+};
+
 &pm6150l_flash {
 	status = "okay";
 

-- 
2.53.0

[PATCH v2 4/8] arm64: dts: qcom: sm6350-lena: Enable IPA

[erebion]

Enable the IPA node for the Xperia 10 III which makes mobile data work.

Signed-off-by: erebion <erebion@erebion.eu>
---
 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 6 ++++++
 1 file changed, 6 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index c58047ce3291d..f3ed6445c7d35 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -333,6 +333,12 @@ touchscreen@48 {
 	};
 };
 
+&ipa {
+	firmware-name = "qcom/sm6350/sony/pdx213/ipa_fws.mbn";
+
+	status = "okay";
+};
+
 &mpss {
 	firmware-name = "qcom/sm6350/sony/pdx213/modem.mbn";
 

-- 
2.53.0

[PATCH v2 5/8] arm64: dts: qcom: sm6350-lena: Enable Bluetooth

[erebion]

Configure the required regulators for Bluetooth and enable it on the
Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 109 +++++++++++++++++++++
 1 file changed, 109 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index f3ed6445c7d35..9be0e7ceccb55 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -19,6 +19,10 @@ / {
 	qcom,msm-id = <434 0x10000>, <459 0x10000>;
 	qcom,board-id = <0x1000b 0>;
 
+	aliases {
+		serial1 = &uart1;
+	};
+
 	chosen {
 		#address-cells = <2>;
 		#size-cells = <2>;
@@ -381,6 +385,44 @@ &qupv3_id_1 {
 	status = "okay";
 };
 
+/* UART1: HS UART for Bluetooth */
+&qup_uart1_cts {
+	/*
+	 * Configure a bias-bus-hold on CTS to lower power
+	 * usage when Bluetooth is turned off. Bus hold will
+	 * maintain a low power state regardless of whether
+	 * the Bluetooth module drives the pin in either
+	 * direction or leaves the pin fully unpowered.
+	 */
+	/delete-property/ bias-disable;
+	bias-bus-hold;
+};
+
+&qup_uart1_rts {
+	/* We'll drive RTS, so no pull */
+	drive-strength = <2>;
+	/delete-property/ bias-pull-down;
+	bias-disable;
+};
+
+&qup_uart1_rx {
+	/*
+	 * Configure a pull-up on RX. This is needed to avoid
+	 * garbage data when the TX pin of the Bluetooth module is
+	 * in tri-state (module powered off or not driving the
+	 * signal yet).
+	 */
+	/delete-property/ bias-disable;
+	bias-pull-up;
+};
+
+&qup_uart1_tx {
+	/* We'll drive TX, so no pull */
+	drive-strength = <2>;
+	/delete-property/ bias-pull-up;
+	bias-disable;
+};
+
 &sdc2_off_state {
 	sd-cd-pins {
 		pins = "gpio94";
@@ -424,6 +466,73 @@ ts_int_default: ts-int-default-state {
 		drive-strength = <2>;
 		bias-disable;
 	};
+
+	qup_uart1_sleep_cts: qup-uart1-sleep-cts-state {
+		pins = "gpio61";
+		function = "gpio";
+		/*
+		 * Configure a bias-bus-hold on CTS to lower power
+		 * usage when Bluetooth is turned off. Bus hold will
+		 * maintain a low power state regardless of whether
+		 * the Bluetooth module drives the pin in either
+		 * direction or leaves the pin fully unpowered.
+		 */
+		bias-bus-hold;
+	};
+
+	qup_uart1_sleep_rts: qup-uart1-sleep-rts-state {
+		pins = "gpio62";
+		function = "gpio";
+		/*
+		 * Configure pull-down on RTS. As RTS is active low
+		 * signal, pull it low to indicate the BT SoC that it
+		 * can wakeup the system anytime from suspend state by
+		 * pulling RX low (by sending wakeup bytes).
+		 */
+		bias-pull-down;
+	};
+
+	qup_uart1_sleep_rx: qup-uart1-sleep-rx-state {
+		pins = "gpio64";
+		function = "gpio";
+		/*
+		 * Configure a pull-up on RX. This is needed to avoid
+		 * garbage data when the TX pin of the Bluetooth module
+		 * is floating which may cause spurious wakeups.
+		 */
+		bias-pull-up;
+	};
+
+	qup_uart1_sleep_tx: qup-uart1-sleep-tx-state {
+		pins = "gpio63";
+		function = "gpio";
+		/*
+		 * Configure pull-up on TX when it isn't actively driven
+		 * to prevent BT SoC from receiving garbage during sleep.
+		 */
+		bias-pull-up;
+	};
+};
+
+&uart1 {
+	/delete-property/ interrupts;
+	interrupts-extended = <&intc GIC_SPI 602 IRQ_TYPE_LEVEL_HIGH>,
+			     <&tlmm 64 IRQ_TYPE_EDGE_FALLING>;
+
+	pinctrl-names = "default", "sleep";
+	pinctrl-1 = <&qup_uart1_sleep_cts>, <&qup_uart1_sleep_rts>, <&qup_uart1_sleep_tx>, <&qup_uart1_sleep_rx>;
+
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn3991-bt";
+		vddio-supply = <&pm6350_l11>;
+		vddxo-supply = <&pm6350_l7>;
+		vddrf-supply = <&pm6150l_l2>;
+		vddch0-supply = <&pm6150l_l10>;
+		swctrl-gpios = <&tlmm 69 GPIO_ACTIVE_HIGH>;
+		firmware-name = "crnv32u.bin";
+	};
 };
 
 &usb_1 {

-- 
2.53.0

[PATCH v2 6/8] arm64: dts: qcom: sm6350-lena: Enable wifi

[erebion]

Configure regulators and enable it for the Xperia 10 III

Signed-off-by: erebion <erebion@erebion.eu>
---
 arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts | 10 ++++++++++
 1 file changed, 10 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 9be0e7ceccb55..b234919c301f0 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -559,3 +559,13 @@ &usb_1_qmpphy {
 
 	status = "okay";
 };
+
+&wifi {
+	vdd-0.8-cx-mx-supply = <&pm6350_l4>;
+	vdd-1.8-xo-supply = <&pm6350_l7>;
+	vdd-1.3-rfa-supply = <&pm6150l_l2>;
+	vdd-3.3-ch0-supply = <&pm6150l_l10>;
+	vdd-3.3-ch1-supply = <&pm6150l_l11>;
+
+	status = "okay";
+};

-- 
2.53.0

[PATCH v2 7/8] arm64: dts: qcom: sm6350-lena: Enable PM7250B

[erebion]

Enable PM7250B and some components on it for the Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 48 ++++++++++++++++++++++
 1 file changed, 48 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index b234919c301f0..08ad5613cb6de 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -4,6 +4,10 @@
  */
 /dts-v1/;
 
+/* PM7250B is configured to use SID2/3 */
+#define PM7250B_SID 2
+#define PM7250B_SID1 3
+
 #include <dt-bindings/firmware/qcom,scm.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
@@ -11,6 +15,7 @@
 #include "sm6350.dtsi"
 #include "pm6150l.dtsi"
 #include "pm6350.dtsi"
+#include "pm7250b.dtsi"
 
 / {
 	model = "Sony Xperia 10 III";
@@ -377,6 +382,49 @@ &pm6350_resin {
 	status = "okay";
 };
 
+&pm7250b_adc {
+	channel@4d {
+		reg = <ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "charger_skin_therm";
+	};
+
+	channel@4f {
+		reg = <ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "conn_therm";
+	};
+};
+
+&pm7250b_adc_tm {
+	status = "okay";
+
+	charger-skin-therm@0 {
+		reg = <0>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+
+	conn-therm@1 {
+		reg = <1>;
+		io-channels = <&pm7250b_adc ADC5_AMUX_THM3_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time-us = <200>;
+	};
+};
+
+&pm7250b_vbus {
+	regulator-min-microamp = <500000>;
+	regulator-max-microamp = <1500000>;
+
+	status = "okay";
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

-- 
2.53.0

[PATCH v2 8/8] arm64: dts: qcom: sm6350-lena: Enable PMK8350

[erebion]

Configure and enable nodes for PMK8350 on the Xperia 10 III.

Signed-off-by: erebion <erebion@erebion.eu>
---
 .../dts/qcom/sm6350-sony-xperia-lena-pdx213.dts    | 30 ++++++++++++++++++++++
 1 file changed, 30 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
index 08ad5613cb6de..0f0e81683f2e5 100644
--- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
+++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
@@ -8,7 +8,11 @@
 #define PM7250B_SID 2
 #define PM7250B_SID1 3
 
+/* PMK8350 (in reality a PMK8003) is configured to use SID6 instead of 0 */
+#define PMK8350_SID 6
+
 #include <dt-bindings/firmware/qcom,scm.h>
+#include <dt-bindings/iio/qcom,spmi-adc7-pmk8350.h>
 #include <dt-bindings/leds/common.h>
 #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
 #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
@@ -16,6 +20,7 @@
 #include "pm6150l.dtsi"
 #include "pm6350.dtsi"
 #include "pm7250b.dtsi"
+#include "pmk8350.dtsi"
 
 / {
 	model = "Sony Xperia 10 III";
@@ -425,6 +430,31 @@ &pm7250b_vbus {
 	status = "okay";
 };
 
+&pmk8350_adc_tm {
+	status = "okay";
+
+	xo-therm@0 {
+		reg = <0>;
+		io-channels = <&pmk8350_vadc PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		qcom,hw-settle-time-us = <200>;
+		qcom,ratiometric;
+	};
+};
+
+&pmk8350_rtc {
+	status = "okay";
+};
+
+&pmk8350_vadc {
+	channel@644 {
+		reg = <PMK8350_ADC7_AMUX_THM1_100K_PU>;
+		qcom,ratiometric;
+		qcom,hw-settle-time = <200>;
+		qcom,pre-scaling = <1 1>;
+		label = "xo_therm";
+	};
+};
+
 &qupv3_id_0 {
 	status = "okay";
 };

-- 
2.53.0

Re: [PATCH v2 1/8] arm64: dts: qcom: sm6350-lena: Add flash LED

[Luca Weiss]

Hi erebion,

On Sat Sep 26, 2026 at 4:00 PM CEST, erebion wrote:
> Add a node for the camera flash LED found on the Xperia 10 III
>

Reviewed-by: Luca Weiss <luca.weiss@fairphone.com>

> Signed-off-by: erebion <erebion@erebion.eu>
> ---
>  .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts      | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
>
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 6e2bbf4f060ac..79aa2521aed40 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -4,9 +4,11 @@
>   */
>  /dts-v1/;
>  
> +#include <dt-bindings/leds/common.h>
>  #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>  #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>  #include "sm6350.dtsi"
> +#include "pm6150l.dtsi"
>  #include "pm6350.dtsi"
>  
>  / {
> @@ -302,6 +304,19 @@ touchscreen@48 {
>  	};
>  };
>  
> +&pm6150l_flash {
> +	status = "okay";
> +
> +	led-0 {
> +		function = LED_FUNCTION_FLASH;
> +		color = <LED_COLOR_ID_WHITE>;
> +		led-sources = <1>;
> +		led-max-microamp = <180000>;
> +		flash-max-microamp = <1000000>;
> +		flash-max-timeout-us = <1280000>;
> +	};
> +};
> +
>  &pm6350_gpios {
>  	vol_down_n: vol-down-n-state {
>  		pins = "gpio2";

Re: [PATCH v2 1/8] arm64: dts: qcom: sm6350-lena: Add flash LED

[Bjorn Andersson]

On Sat, Sep 26, 2026 at 04:00:50PM +0200, erebion wrote:
> Add a node for the camera flash LED found on the Xperia 10 III
> 
> Signed-off-by: erebion <erebion@erebion.eu>

Per
https://www.kernel.org/doc/html/v4.19/process/submitting-patches.html#developer-s-certificate-of-origin-1-1
please use your real name.

Regards,
Bjorn

> ---
>  .../boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts      | 15 +++++++++++++++
>  1 file changed, 15 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> index 6e2bbf4f060ac..79aa2521aed40 100644
> --- a/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> +++ b/arch/arm64/boot/dts/qcom/sm6350-sony-xperia-lena-pdx213.dts
> @@ -4,9 +4,11 @@
>   */
>  /dts-v1/;
>  
> +#include <dt-bindings/leds/common.h>
>  #include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
>  #include <dt-bindings/regulator/qcom,rpmh-regulator.h>
>  #include "sm6350.dtsi"
> +#include "pm6150l.dtsi"
>  #include "pm6350.dtsi"
>  
>  / {
> @@ -302,6 +304,19 @@ touchscreen@48 {
>  	};
>  };
>  
> +&pm6150l_flash {
> +	status = "okay";
> +
> +	led-0 {
> +		function = LED_FUNCTION_FLASH;
> +		color = <LED_COLOR_ID_WHITE>;
> +		led-sources = <1>;
> +		led-max-microamp = <180000>;
> +		flash-max-microamp = <1000000>;
> +		flash-max-timeout-us = <1280000>;
> +	};
> +};
> +
>  &pm6350_gpios {
>  	vol_down_n: vol-down-n-state {
>  		pins = "gpio2";
> 
> -- 
> 2.53.0
> 
>