mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Frank Li <Frank.li@oss.nxp.com>
To: Koichiro Den <den@valinux.co.jp>
Cc: "Frank Li" <Frank.Li@kernel.org>,
	"Manivannan Sadhasivam" <mani@kernel.org>,
	"Krzysztof Wilczyński" <kwilczynski@kernel.org>,
	"Kishon Vijay Abraham I" <kishon@kernel.org>,
	"Jon Mason" <jdmason@kudzu.us>,
	"Dave Jiang" <dave.jiang@intel.com>,
	"Allen Hubbe" <allenbh@gmail.com>,
	"Niklas Cassel" <cassel@kernel.org>,
	"Bjorn Helgaas" <bhelgaas@google.com>,
	"Jonathan Corbet" <corbet@lwn.net>,
	"Shuah Khan" <skhan@linuxfoundation.org>,
	"Randy Dunlap" <rdunlap@infradead.org>,
	"Jingoo Han" <jingoohan1@gmail.com>,
	"Lorenzo Pieralisi" <lpieralisi@kernel.org>,
	"Rob Herring" <robh@kernel.org>,
	"Jerome Brunet" <jbrunet@baylibre.com>,
	linux-pci@vger.kernel.org, linux-doc@vger.kernel.org,
	linux-kernel@vger.kernel.org, ntb@lists.linux.dev
Subject: Re: [PATCH v7 10/10] NTB: ntb_hw_epf: Support DMA and MW sharing a BAR
Date: Wed, 21 Oct 2026 13:51:23 -0500	[thread overview]
Message-ID: <atkJqyI2GZRvWo-m@SMW015318> (raw)
In-Reply-To: <eg2sbks43lnyvs7i6jtzqkhqkgpjalgynhkwi2c2pkpklrbekv@oiscofavvmxh>

On Thu, Oct 22, 2026 at 01:57:29AM +0900, Koichiro Den wrote:
> On Wed, Oct 21, 2026 at 10:58:54AM -0500, Frank Li wrote:
> > On Wed, Oct 21, 2026 at 01:22:29PM +0900, Koichiro Den wrote:
> > > A vNTB endpoint can place DMA resources after an MW in the same BAR.
> > > Limit the MW to the advertised boundary so clients cannot overwrite
> > > those resources.
> > >
> > > Advertise this support in LINK_UP, including when DMA is unavailable.
> > > Older endpoints ignore the argument.
> >
> > if ignore it, any side effect? Does host DMA side use wrong memory region,
> > which actually is not mapped by EP?
>
> None. This only advertises the host's support for MW/DMA BAR sharing.
> Without DMA metadata from the EP, the host does not initialize endpoint DMA.
>
> JFTR, this is the case I described in the cover letter, see [1] below:
>
>   EP                              | Old host     | New host
>   --------------------------------+--------------+----------
>   Old                             | OK           | OK [1]
>   New (dma_bar = -1)              | OK           | OK
>   New (dedicated DMA BAR)         | OK           | OK
>   New (shared MW/DMA BAR)         | Rejected     | OK
>
> I've retested the [1] case with R-Car S4 just in case ...

Reviewed-by: Frank Li <Frank.Li@nxp.com>

>
> Best regards,
> Koichiro Den
>
> >
> > Frank
> >
> > >
> > > Signed-off-by: Koichiro Den <den@valinux.co.jp>
> > > ---
> > > Changes since v6:
> > >   - Split from the BAR-sharing patch. (Frank)
> > >   - Advertise MW/DMA BAR boundary support in LINK_UP.
> > >
> > >  drivers/ntb/hw/epf/ntb_hw_epf.c | 46 +++++++++++++++++++++++++++------
> > >  1 file changed, 38 insertions(+), 8 deletions(-)
> > >
> > > diff --git a/drivers/ntb/hw/epf/ntb_hw_epf.c b/drivers/ntb/hw/epf/ntb_hw_epf.c
> > > index e0016128b95c..56185870cba9 100644
> > > --- a/drivers/ntb/hw/epf/ntb_hw_epf.c
> > > +++ b/drivers/ntb/hw/epf/ntb_hw_epf.c
> > > @@ -382,6 +382,23 @@ static int ntb_epf_mw_to_bar(struct ntb_epf_dev *ndev, int idx)
> > >  	return ndev->barno_map[BAR_MW1 + idx];
> > >  }
> > >
> > > +static resource_size_t ntb_epf_mw_offset(struct ntb_epf_dev *ndev, int idx)
> > > +{
> > > +	return !idx ? readl(ndev->ctrl_reg + NTB_EPF_CTRL(mw1_offset)) : 0;
> > > +}
> > > +
> > > +static resource_size_t ntb_epf_mw_size(struct ntb_epf_dev *ndev, int bar)
> > > +{
> > > +	resource_size_t end;
> > > +
> > > +	end = pci_resource_len(ndev->ntb.pdev, bar);
> > > +	/* The DMA submap offset marks the end of an MW sharing this BAR. */
> > > +	if (ndev->dma.submap.size && ndev->dma.submap.bar == bar)
> > > +		end = min(end, ndev->dma.submap.offset);
> > > +
> > > +	return end;
> > > +}
> > > +
> > >  static int ntb_epf_mw_count(struct ntb_dev *ntb, int pidx)
> > >  {
> > >  	struct ntb_epf_dev *ndev = ntb_ndev(ntb);
> > > @@ -420,7 +437,7 @@ static int ntb_epf_mw_get_align(struct ntb_dev *ntb, int pidx, int idx,
> > >  		*size_align = 1;
> > >
> > >  	if (size_max)
> > > -		*size_max = pci_resource_len(ndev->ntb.pdev, bar);
> > > +		*size_max = ntb_epf_mw_size(ndev, bar);
> > >
> > >  	return 0;
> > >  }
> > > @@ -524,7 +541,8 @@ static int ntb_epf_link_enable(struct ntb_dev *ntb,
> > >  	struct device *dev = ndev->dev;
> > >  	int ret;
> > >
> > > -	ret = ntb_epf_send_command(ndev, EPF_NTB_COMMAND_LINK_UP, 0);
> > > +	ret = ntb_epf_send_command(ndev, EPF_NTB_COMMAND_LINK_UP,
> > > +				   EPF_NTB_LINK_UP_DMA_MW_SUPPORTED);
> > >  	if (ret) {
> > >  		dev_err(dev, "Fail to enable link\n");
> > >  		return ret;
> > > @@ -707,7 +725,7 @@ static int ntb_epf_mw_set_trans(struct ntb_dev *ntb, int pidx, int idx,
> > >  	if (bar < 0)
> > >  		return bar;
> > >
> > > -	mw_size = pci_resource_len(ntb->pdev, bar);
> > > +	mw_size = ntb_epf_mw_size(ndev, bar);
> > >
> > >  	if (size > mw_size) {
> > >  		dev_err(dev, "Size:%pa is greater than the MW size %pa\n",
> > > @@ -739,21 +757,20 @@ static int ntb_epf_peer_mw_get_addr(struct ntb_dev *ntb, int idx,
> > >  				    phys_addr_t *base, resource_size_t *size)
> > >  {
> > >  	struct ntb_epf_dev *ndev = ntb_ndev(ntb);
> > > -	u32 offset = 0;
> > > +	resource_size_t offset;
> > >  	int bar;
> > >
> > > -	if (idx == 0)
> > > -		offset = readl(ndev->ctrl_reg + NTB_EPF_CTRL(mw1_offset));
> > > -
> > >  	bar = ntb_epf_mw_to_bar(ndev, idx);
> > >  	if (bar < 0)
> > >  		return bar;
> > >
> > > +	offset = ntb_epf_mw_offset(ndev, idx);
> > > +
> > >  	if (base)
> > >  		*base = pci_resource_start(ndev->ntb.pdev, bar) + offset;
> > >
> > >  	if (size)
> > > -		*size = pci_resource_len(ndev->ntb.pdev, bar) - offset;
> > > +		*size = ntb_epf_mw_size(ndev, bar) - offset;
> > >
> > >  	return 0;
> > >  }
> > > @@ -851,6 +868,7 @@ static int ntb_epf_init_dev(struct ntb_epf_dev *ndev)
> > >  {
> > >  	struct device *dev = ndev->dev;
> > >  	int ret;
> > > +	int i;
> > >
> > >  	ndev->mw_count = readl(ndev->ctrl_reg + NTB_EPF_CTRL(num_mws));
> > >  	if (ndev->mw_count > NTB_EPF_MAX_MW_COUNT) {
> > > @@ -862,6 +880,18 @@ static int ntb_epf_init_dev(struct ntb_epf_dev *ndev)
> > >  		dev_err(dev, "Invalid endpoint DMA layout\n");
> > >  		return ret;
> > >  	}
> > > +	if (ndev->dma.submap.size) {
> > > +		for (i = 0; i < ndev->mw_count; i++) {
> > > +			int bar = ntb_epf_mw_to_bar(ndev, i);
> > > +
> > > +			if (bar == ndev->dma.submap.bar &&
> > > +			    ntb_epf_mw_size(ndev, bar) <=
> > > +			    ntb_epf_mw_offset(ndev, i)) {
> > > +				dev_err(dev, "Invalid DMA/MW boundary\n");
> > > +				return -EINVAL;
> > > +			}
> > > +		}
> > > +	}
> > >
> > >  	/* One Link interrupt and rest doorbell interrupt */
> > >  	ret = ntb_epf_init_isr(ndev, NTB_EPF_MIN_DB_COUNT + 1,
> > > --
> > > 2.54.0
> > >

      reply	other threads:[~2026-10-21 18:51 UTC|newest]

Thread overview: 18+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
2026-10-21  4:22 [PATCH v7 00/10] PCI: endpoint: Remote DMA support via vNTB Koichiro Den
2026-10-21  4:22 ` [PATCH v7 01/10] PCI: endpoint: Add DMA auxiliary resource metadata Koichiro Den
2026-10-21  4:22 ` [PATCH v7 02/10] PCI: dwc: Expose endpoint DMA resources Koichiro Den
2026-10-21  4:22 ` [PATCH v7 03/10] PCI: endpoint: pci-epf-vntb: Move epf_ntb_is_bar_used() up Koichiro Den
2026-10-21  4:22 ` [PATCH v7 04/10] PCI: endpoint: Add pci-epf-ntb.h for the shared NTB control layout Koichiro Den
2026-10-21  4:22 ` [PATCH v7 05/10] PCI: endpoint: pci-epf-vntb: Export endpoint DMA channels Koichiro Den
2026-10-21  4:22 ` [PATCH v7 06/10] PCI: endpoint: pci-epf-vntb: Allow DMA and MW to share a BAR Koichiro Den
2026-10-21 15:52   ` Frank Li
2026-10-21 16:35     ` Koichiro Den
2026-10-21 19:00       ` Frank Li
2026-10-21  4:22 ` [PATCH v7 07/10] Documentation: PCI: endpoint: Document vNTB DMA export Koichiro Den
2026-10-21  4:22 ` [PATCH v7 08/10] NTB: ntb_hw_epf: Use the shared NTB control layout Koichiro Den
2026-10-21 15:53   ` Frank Li
2026-10-21  4:22 ` [PATCH v7 09/10] NTB: ntb_hw_epf: Discover vNTB-embedded DMA Koichiro Den
2026-10-21  4:22 ` [PATCH v7 10/10] NTB: ntb_hw_epf: Support DMA and MW sharing a BAR Koichiro Den
2026-10-21 15:58   ` Frank Li
2026-10-21 16:57     ` Koichiro Den
2026-10-21 18:51       ` Frank Li [this message]

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=atkJqyI2GZRvWo-m@SMW015318 \
    --to=frank.li@oss.nxp.com \
    --cc=Frank.Li@kernel.org \
    --cc=allenbh@gmail.com \
    --cc=bhelgaas@google.com \
    --cc=cassel@kernel.org \
    --cc=corbet@lwn.net \
    --cc=dave.jiang@intel.com \
    --cc=den@valinux.co.jp \
    --cc=jbrunet@baylibre.com \
    --cc=jdmason@kudzu.us \
    --cc=jingoohan1@gmail.com \
    --cc=kishon@kernel.org \
    --cc=kwilczynski@kernel.org \
    --cc=linux-doc@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-pci@vger.kernel.org \
    --cc=lpieralisi@kernel.org \
    --cc=mani@kernel.org \
    --cc=ntb@lists.linux.dev \
    --cc=rdunlap@infradead.org \
    --cc=robh@kernel.org \
    --cc=skhan@linuxfoundation.org \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®