From: Viresh Kumar <viresh.kumar@linaro.org>
To: Pierre Gondois <pierre.gondois@arm.com>,
Ananthu C V <ananthu.cv@oss.qualcomm.com>
Cc: Vincent Guittot <vincent.guittot@linaro.org>,
Sudeep Holla <sudeep.holla@kernel.org>,
Greg Kroah-Hartman <gregkh@linuxfoundation.org>,
"Rafael J. Wysocki" <rafael@kernel.org>,
Danilo Krummrich <dakr@kernel.org>,
Jie Zhan <zhanjie9@hisilicon.com>,
linux-kernel@vger.kernel.org, driver-core@lists.linux.dev,
linux-pm@vger.kernel.org,
"Rafael J. Wysocki" <rafael.j.wysocki@intel.com>,
Oleg Keri <okerixx@gmail.com>
Subject: Re: [PATCH v3 2/2] cpufreq: fix policy max not returning to non-boost freq on boost disable
Date: Thu, 19 Nov 2026 10:19:16 +0530 [thread overview]
Message-ID: <av5_zDI4bg28H_6e@vireshk-B250M-D3H> (raw)
In-Reply-To: <av2aFWw3kh11U68A@hu-anancv-blr.qualcomm.com>
On 18-11-26, 17:59, Ananthu C V wrote:
> This does fix the issue of policy->max not being able to drop down back
> to non-boost values after boost disable, but I found another caveat.
>
> The commit 8c83947c5dbb added the following change a few months ago;
>
> static int cpufreq_policy_init_qos(struct cpufreq_policy *policy)
> {
> + unsigned int min_freq, max_freq;
> int ret;
>
> + /* Use policy->min/max set by the driver as QoS requests. */
> + min_freq = max(FREQ_QOS_MIN_DEFAULT_VALUE, policy->min);
> + if (policy->max)
> + max_freq = min(FREQ_QOS_MAX_DEFAULT_VALUE, policy->max);
> + else
> + max_freq = FREQ_QOS_MAX_DEFAULT_VALUE;
>
> this max_freq is then subsequently used to update max_freq_req constraint
> for the policy. This means, assigning a value to policy max in freq table
> directly will cause the same to be kept as the max_freq_req, which if
> boost is not enabled will be stuck at a non-boost value. The boost will
> still work, as policy max is set directly, but the value will be above
> the allowed qos max;
>
> # echo 1 > ../boost
> cpufreq: cpufreq: policy12 boost=1 policy->max=4723200 qos_max=4454400
> cpufreq: cpufreq: policy6 boost=1 policy->max=4723200 qos_max=4454400
>
> This also means if at any later point any limit refresh happens, the
> value will be brought back to that qos max, which is a non-boost value,
> even when boost is enabled;
>
> (e.g. here with a refresh_frequency_limits(policy); call after the boost)
>
> # echo 1 > ../boost
> cpufreq: cpufreq: policy12 boost=1 policy->max=4454400 qos_max=4454400
> cpufreq: cpufreq: policy6 boost=1 policy->max=4454400 qos_max=4454400
>
> tldr; is that it will fix the issue of the freq not dropping down from
> boost, but it will introduce a new potential problem of boost state
> potentially dropping back to non-boost freq while still in boost.
>
> So this alone can't be a fix at the very least. At the bare minimum it
> will need update to how max_freq_req is calculated/updated, etc. If
> nobody assigns values to policy->max before cpufreq_policy_init_qos
> is called, max_freq_req can simply use FREQ_QOS_MAX_DEFAULT_VALUE,
> which is S32_MAX, as its value, and not cause this problem, so the
> solution proposed in the current series will not run into this.
>
> > Also, can you please explain the issue again in detail. I am not very
> > sure how you are reaching to this issue over current mainline (without
> > the first patch).
>
> There are two issues the series is trying to address;
> 1. freq can go upto boost values, but they cannot be actually used
> 2. once a policy is using a boost value, that value cannot go back to a
> non boost value.
>
> So with or without patch 1, which addresses the first issue, the freq
> can still go to boost values, which can trigger the second issue. The
> logs relevant to the second issue, reusing from the cover letter, is;
>
> \# cd /sys/devices/system/cpu/cpufreq/
> \# ls
> boost policy0 policy12 policy6
> \# cat boost
> 0
> \# cat policy6/scaling_max_freq
> 4454400
> \# echo 1 > boost
> \# cat policy6/scaling_max_freq
> 4723200
> \# echo 0 > boost
> \# cat policy6/scaling_max_freq
> 472320
>
> The reason why this is happening is;
>
> from freq_table.c:
>
> if (policy->cpuinfo.max_freq < max_freq)
> policy->cpuinfo.max_freq = max_freq;
>
> and from cpufreq.c:
>
> freq_qos_update_request(&policy->boost_freq_req, policy->cpuinfo.max_freq);
>
> so cpuinfo.max_freq is only updated upwards, and that value is used to update
> boost_freq_req, which is a FREQ_QOS_MAX request. On boost enable and disable
> the cpuinfo.max_freq value stuck at the top will be used to update the qos
> max, and the value never comes down.
Pierre, any inputs ?
--
viresh
next prev parent reply other threads:[~2026-11-19 4:49 UTC|newest]
Thread overview: 20+ messages / expand[flat|nested] mbox.gz Atom feed top
2026-09-29 11:38 [PATCH v3 0/2] sched/cpufreq: fix schedutil's boost frequency handling Ananthu C V
2026-09-29 11:38 ` [PATCH v3 1/2] arch_topology: seed capacity_freq_ref with highest available frequency Ananthu C V
2026-10-11 14:16 ` Zhongqiu Han
2026-10-12 18:45 ` Dietmar Eggemann
2026-10-13 11:28 ` Zhongqiu Han
2026-11-11 12:10 ` Ananthu C V
2026-11-11 12:12 ` Ananthu C V
2026-09-29 11:38 ` [PATCH v3 2/2] cpufreq: fix policy max not returning to non-boost freq on boost disable Ananthu C V
2026-10-11 14:17 ` Zhongqiu Han
2026-11-11 12:21 ` Ananthu C V
2026-11-11 13:47 ` Zhongqiu Han
2026-10-11 23:42 ` Dietmar Eggemann
2026-11-11 12:27 ` Ananthu C V
2026-11-02 8:38 ` Viresh Kumar
2026-11-11 12:40 ` Ananthu C V
2026-11-17 10:34 ` Viresh Kumar
2026-11-18 12:29 ` Ananthu C V
2026-11-19 4:49 ` Viresh Kumar [this message]
2026-11-20 12:08 ` Pierre Gondois
2026-09-30 9:10 ` [PATCH v3 0/2] sched/cpufreq: fix schedutil's boost frequency handling Oleg Keri
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=av5_zDI4bg28H_6e@vireshk-B250M-D3H \
--to=viresh.kumar@linaro.org \
--cc=ananthu.cv@oss.qualcomm.com \
--cc=dakr@kernel.org \
--cc=driver-core@lists.linux.dev \
--cc=gregkh@linuxfoundation.org \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-pm@vger.kernel.org \
--cc=okerixx@gmail.com \
--cc=pierre.gondois@arm.com \
--cc=rafael.j.wysocki@intel.com \
--cc=rafael@kernel.org \
--cc=sudeep.holla@kernel.org \
--cc=vincent.guittot@linaro.org \
--cc=zhanjie9@hisilicon.com \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®