* [RESEND PATCH v4 0/2] i2c: i2c-xiic: fix clearing of bnb irq and waiting/ clearing while atomic
@ 2026-11-18 10:11 Thilo Zirnstein
2026-11-18 10:11 ` [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq Thilo Zirnstein
2026-11-18 10:11 ` [PATCH v4 2/2] i2c: i2c-xiic: fix waiting/clearing while atomic Thilo Zirnstein
0 siblings, 2 replies; 6+ messages in thread
From: Thilo Zirnstein @ 2026-11-18 10:11 UTC (permalink / raw)
To: michal.simek, andi.shyti
Cc: linux-arm-kernel, linux-i2c, linux-kernel, Thilo Zirnstein
Resend due to inactivity since Nov 09.
I think PATCH v4 2/2 misses a review.
Anything I can do to move this further ?
Dear all,
This patch-series fixes the clearing routine for the bus not busy (bnb) irq
plus the waiting and clearing routines while in atomic context.
The bnb is used to indicate that the current transfer is done.
A high level view of the software flow for tx:
* init i2c controller
* prepare all registers ( fill fifo, enable irqs, ... )
* start i2c txfer
* clear and enable bnb
* wait for completion
* ( serve interrupts )
* ( bnb interrupt ): complete completion
The datasheet ( pg090-axi-iic, Interrupt-Status-Register ISR)
states that the bnb bit can only be cleared if
the bus busy bit in the status register is set.
So the iic controller must have recognized that their is some activity
on the bus. ( Start condition )
Currently the bnb bit is cleared without checking or waiting for this
condition. This can lead to spurious bnb interrupts.
Andi suggested to use an atomic-save function to wait for bnb.
This was applied for other waiting/ clearing functions, too.
Kind regards,
Thilo Zirnstein
---
RESEND v4
- Add Reviewed-by Tag
Changes in v4
- Fix timeout argument of polling in atomic context
Changes in v3
- Use atomic-save functions for waiting and clearing.
- Fix intendation
- Unintentional changes removed
Changes in v2:
- Unintentional changes removed.
---
Thilo Zirnstein (2):
i2c: i2c-xiic: fix clearing of bnb irq
i2c: i2c-xiic: fix waiting/clearing while atomic
drivers/i2c/busses/i2c-xiic.c | 70 ++++++++++++++++++++++++++++-------
1 file changed, 57 insertions(+), 13 deletions(-)
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq
2026-11-18 10:11 [RESEND PATCH v4 0/2] i2c: i2c-xiic: fix clearing of bnb irq and waiting/ clearing while atomic Thilo Zirnstein
@ 2026-11-18 10:11 ` Thilo Zirnstein
2026-11-18 13:22 ` Andi Shyti
2026-11-18 10:11 ` [PATCH v4 2/2] i2c: i2c-xiic: fix waiting/clearing while atomic Thilo Zirnstein
1 sibling, 1 reply; 6+ messages in thread
From: Thilo Zirnstein @ 2026-11-18 10:11 UTC (permalink / raw)
To: michal.simek, andi.shyti
Cc: linux-arm-kernel, linux-i2c, linux-kernel, Thilo Zirnstein,
Shubhrajyoti Datta
Add a function for clearing the bnb bit,
It waits for all preconditions before clearing the bnb bit or times out.
Reviewed-by: Shubhrajyoti Datta <shubhrajyoti.datta@amd.com>
Signed-off-by: Thilo Zirnstein <thi.zirnstein@gmail.com>
---
drivers/i2c/busses/i2c-xiic.c | 40 ++++++++++++++++++++++++++++-------
1 file changed, 32 insertions(+), 8 deletions(-)
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index ba560462d451..e68e17bdf0ba 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -233,6 +233,8 @@ static const struct timing_regs timing_reg_values[] = {
#define XIIC_RESET_MASK 0xAUL
#define XIIC_PM_TIMEOUT 1000 /* ms */
+/* timeout waiting for bus busy */
+#define XIIC_BB_TIMEOUT_US 1000
/* timeout waiting for the controller to respond */
#define XIIC_I2C_TIMEOUT (msecs_to_jiffies(1000))
/* timeout waiting for the controller finish transfers */
@@ -394,6 +396,30 @@ static int xiic_wait_tx_empty(struct xiic_i2c *i2c)
return 0;
}
+static void xiic_clear_en_bnb(struct xiic_i2c *i2c)
+{
+ u8 sr = 0, isr = 0;
+ int ret;
+
+ isr = xiic_getreg8(i2c, XIIC_IISR_OFFSET);
+ if (!(isr & XIIC_INTR_BNB_MASK)) {
+ xiic_irq_en(i2c, XIIC_INTR_BNB_MASK);
+ return;
+ }
+
+ ret = read_poll_timeout_atomic(xiic_getreg8, sr,
+ sr & XIIC_SR_BUS_BUSY_MASK, 0, XIIC_BB_TIMEOUT_US, 0,
+ i2c, XIIC_SR_REG_OFFSET);
+
+ if (ret) {
+ dev_err(i2c->dev, "Failed to clear bnb\n");
+ return;
+ }
+
+ xiic_setreg8(i2c, XIIC_IISR_OFFSET, XIIC_INTR_BNB_MASK);
+ xiic_irq_en(i2c, XIIC_INTR_BNB_MASK);
+}
+
/**
* xiic_setclk - Sets the configured clock rate
* @i2c: Pointer to the xiic device structure
@@ -883,9 +909,6 @@ static irqreturn_t xiic_process(int irq, void *dev_id)
}
if (pend & XIIC_INTR_BNB_MASK) {
- /* IIC bus has transitioned to not busy */
- clr |= XIIC_INTR_BNB_MASK;
-
/* The bus is not busy, disable BusNotBusy interrupt */
xiic_irq_dis(i2c, XIIC_INTR_BNB_MASK);
@@ -1030,7 +1053,7 @@ static void xiic_start_recv(struct xiic_i2c *i2c)
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, val);
- xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+ xiic_clear_en_bnb(i2c);
} else {
/*
* If previous message is Tx, make sure that Tx FIFO is empty
@@ -1097,7 +1120,7 @@ static void xiic_start_recv(struct xiic_i2c *i2c)
if (i2c->nmsgs == 1)
/* very last, enable bus not busy as well */
- xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+ xiic_clear_en_bnb(i2c);
/* the message is tx:ed */
i2c->tx_pos = msg->len;
@@ -1181,11 +1204,11 @@ static void xiic_start_send(struct xiic_i2c *i2c)
/* Clear any pending Tx empty, Tx Error and then enable them */
xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
XIIC_INTR_TX_ERROR_MASK |
- XIIC_INTR_BNB_MASK |
((i2c->nmsgs > 1 || xiic_tx_space(i2c)) ?
XIIC_INTR_TX_HALF_MASK : 0));
xiic_fill_tx_fifo(i2c);
+ xiic_clear_en_bnb(i2c);
} else {
/*
* If previous message is Tx, make sure that Tx FIFO is empty
@@ -1227,8 +1250,9 @@ static void xiic_start_send(struct xiic_i2c *i2c)
/* Clear any pending Tx empty, Tx Error and then enable them */
xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
- XIIC_INTR_TX_ERROR_MASK |
- XIIC_INTR_BNB_MASK);
+ XIIC_INTR_TX_ERROR_MASK);
+
+ xiic_clear_en_bnb(i2c);
}
i2c->prev_msg_tx = true;
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v4 2/2] i2c: i2c-xiic: fix waiting/clearing while atomic
2026-11-18 10:11 [RESEND PATCH v4 0/2] i2c: i2c-xiic: fix clearing of bnb irq and waiting/ clearing while atomic Thilo Zirnstein
2026-11-18 10:11 ` [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq Thilo Zirnstein
@ 2026-11-18 10:11 ` Thilo Zirnstein
1 sibling, 0 replies; 6+ messages in thread
From: Thilo Zirnstein @ 2026-11-18 10:11 UTC (permalink / raw)
To: michal.simek, andi.shyti
Cc: linux-arm-kernel, linux-i2c, linux-kernel, Thilo Zirnstein
Use non jiffies based waiting functions,
if in atomic context.
Suggested-by: Andi Shyti <andi.shyti@kernel.org>
Signed-off-by: Thilo Zirnstein <thi.zirnstein@gmail.com>
---
drivers/i2c/busses/i2c-xiic.c | 30 +++++++++++++++++++++++++-----
1 file changed, 25 insertions(+), 5 deletions(-)
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index e68e17bdf0ba..6bb8d66e8969 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -237,6 +237,8 @@ static const struct timing_regs timing_reg_values[] = {
#define XIIC_BB_TIMEOUT_US 1000
/* timeout waiting for the controller to respond */
#define XIIC_I2C_TIMEOUT (msecs_to_jiffies(1000))
+/* timeout waiting for the controller to respond in micro seconds */
+#define XIIC_I2C_TIMEOUT_US 1000000
/* timeout waiting for the controller finish transfers */
#define XIIC_XFER_TIMEOUT (msecs_to_jiffies(10000))
/* timeout waiting for the controller finish transfers in micro seconds */
@@ -359,16 +361,28 @@ static inline void xiic_irq_clr_en(struct xiic_i2c *i2c, u32 mask)
xiic_irq_en(i2c, mask);
}
+static int xiic_poll_rx_empty(struct xiic_i2c *i2c)
+{
+ if (xiic_getreg8(i2c, XIIC_SR_REG_OFFSET) &
+ XIIC_SR_RX_FIFO_EMPTY_MASK)
+ return 1;
+
+ xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
+ return 0;
+}
+
static int xiic_clear_rx_fifo(struct xiic_i2c *i2c)
{
- u8 sr;
+ int rx_empty;
unsigned long timeout;
+ if (i2c->atomic)
+ return read_poll_timeout_atomic(xiic_poll_rx_empty,
+ rx_empty, rx_empty, 10, XIIC_I2C_TIMEOUT_US,
+ 0, i2c);
+
timeout = jiffies + XIIC_I2C_TIMEOUT;
- for (sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET);
- !(sr & XIIC_SR_RX_FIFO_EMPTY_MASK);
- sr = xiic_getreg8(i2c, XIIC_SR_REG_OFFSET)) {
- xiic_getreg8(i2c, XIIC_DRR_REG_OFFSET);
+ while (!xiic_poll_rx_empty(i2c)) {
if (time_after(jiffies, timeout)) {
dev_err(i2c->dev, "Failed to clear rx fifo\n");
return -ETIMEDOUT;
@@ -383,6 +397,12 @@ static int xiic_wait_tx_empty(struct xiic_i2c *i2c)
u8 isr;
unsigned long timeout;
+ if (i2c->atomic)
+ return read_poll_timeout_atomic(xiic_getreg32, isr,
+ isr & XIIC_INTR_TX_EMPTY_MASK, 10,
+ XIIC_I2C_TIMEOUT_US, 0, i2c,
+ XIIC_IISR_OFFSET);
+
timeout = jiffies + XIIC_I2C_TIMEOUT;
for (isr = xiic_getreg32(i2c, XIIC_IISR_OFFSET);
!(isr & XIIC_INTR_TX_EMPTY_MASK);
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq
2026-11-18 10:11 ` [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq Thilo Zirnstein
@ 2026-11-18 13:22 ` Andi Shyti
2026-11-19 9:34 ` Thilo Zirnstein
0 siblings, 1 reply; 6+ messages in thread
From: Andi Shyti @ 2026-11-18 13:22 UTC (permalink / raw)
To: Thilo Zirnstein
Cc: michal.simek, linux-arm-kernel, linux-i2c, linux-kernel,
Shubhrajyoti Datta
Hi Thilo,
...
> +static void xiic_clear_en_bnb(struct xiic_i2c *i2c)
> +{
> + u8 sr = 0, isr = 0;
> + int ret;
> +
> + isr = xiic_getreg8(i2c, XIIC_IISR_OFFSET);
> + if (!(isr & XIIC_INTR_BNB_MASK)) {
> + xiic_irq_en(i2c, XIIC_INTR_BNB_MASK);
> + return;
> + }
> +
> + ret = read_poll_timeout_atomic(xiic_getreg8, sr,
> + sr & XIIC_SR_BUS_BUSY_MASK, 0, XIIC_BB_TIMEOUT_US, 0,
> + i2c, XIIC_SR_REG_OFFSET);
this is a bit of an overkill: you are forcing tight loops for
1ms. If you consider that the minimum wait is 1ns, in 1ms you
will end up busy looping a lot of time. Please, don't set the
delay_us to '0', but calculate a proper waiting time between
reads.
Andi
> + if (ret) {
> + dev_err(i2c->dev, "Failed to clear bnb\n");
> + return;
> + }
> +
> + xiic_setreg8(i2c, XIIC_IISR_OFFSET, XIIC_INTR_BNB_MASK);
> + xiic_irq_en(i2c, XIIC_INTR_BNB_MASK);
> +}
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq
2026-11-18 13:22 ` Andi Shyti
@ 2026-11-19 9:34 ` Thilo Zirnstein
0 siblings, 0 replies; 6+ messages in thread
From: Thilo Zirnstein @ 2026-11-19 9:34 UTC (permalink / raw)
To: Andi Shyti
Cc: michal.simek, linux-arm-kernel, linux-i2c, linux-kernel,
Shubhrajyoti Datta
On Wed, Nov 18, 2026 at 02:22:18PM +0100, Andi Shyti wrote:
Hi Andi,
Thank you for your review and feedback
> Hi Thilo,
>
> ...
>
> > + ret = read_poll_timeout_atomic(xiic_getreg8, sr,
> > + sr & XIIC_SR_BUS_BUSY_MASK, 0, XIIC_BB_TIMEOUT_US, 0,
> > + i2c, XIIC_SR_REG_OFFSET);
>
> this is a bit of an overkill: you are forcing tight loops for
> 1ms. If you consider that the minimum wait is 1ns, in 1ms you
> will end up busy looping a lot of time. Please, don't set the
> delay_us to '0', but calculate a proper waiting time between
> reads.
>
I also had doubts about whether this approach is too heavy.
I have general concerns about the busy-waiting in atomic context
in this patches, though I noticed other I2C adapters wait
for relatively long periods there as well.
The tight loops in patch 2/2 are even longer.
Those waits are longer because the code waits for the entire I2C transfer
to finish, but polling is unavoidable there since sleeping or scheduling
deferred work is not possible in atomic context—is that right?
So this kind of builtin if doing i2c transfer in atomic context ?
I will reduce the maximum poll timeout to 4 µs,
which matches the minimum I2C START condition hold time
in standard mode and seems reasonable.
I will also increase delay_us. Out of curiosity,
what is the reasoning behind the delay interval?
I assume we want to avoid hammering shared buses
or registers with continuous I/O reads.
> Andi
kind regards,
Thilo
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq
2026-11-02 9:32 [PATCH v4 0/2] i2c: i2c-xiic: fix clearing of bnb irq and waiting/ clearing " Thilo Zirnstein
@ 2026-11-02 9:32 ` Thilo Zirnstein
0 siblings, 0 replies; 6+ messages in thread
From: Thilo Zirnstein @ 2026-11-02 9:32 UTC (permalink / raw)
To: michal.simek, andi.shyti
Cc: linux-arm-kernel, linux-i2c, linux-kernel, Thilo Zirnstein
Add a function for clearing the bnb bit,
It waits for all preconditions before clearing the bnb bit or times out.
Signed-off-by: Thilo Zirnstein <thi.zirnstein@gmail.com>
---
drivers/i2c/busses/i2c-xiic.c | 40 ++++++++++++++++++++++++++++-------
1 file changed, 32 insertions(+), 8 deletions(-)
diff --git a/drivers/i2c/busses/i2c-xiic.c b/drivers/i2c/busses/i2c-xiic.c
index ba560462d451..e68e17bdf0ba 100644
--- a/drivers/i2c/busses/i2c-xiic.c
+++ b/drivers/i2c/busses/i2c-xiic.c
@@ -233,6 +233,8 @@ static const struct timing_regs timing_reg_values[] = {
#define XIIC_RESET_MASK 0xAUL
#define XIIC_PM_TIMEOUT 1000 /* ms */
+/* timeout waiting for bus busy */
+#define XIIC_BB_TIMEOUT_US 1000
/* timeout waiting for the controller to respond */
#define XIIC_I2C_TIMEOUT (msecs_to_jiffies(1000))
/* timeout waiting for the controller finish transfers */
@@ -394,6 +396,30 @@ static int xiic_wait_tx_empty(struct xiic_i2c *i2c)
return 0;
}
+static void xiic_clear_en_bnb(struct xiic_i2c *i2c)
+{
+ u8 sr = 0, isr = 0;
+ int ret;
+
+ isr = xiic_getreg8(i2c, XIIC_IISR_OFFSET);
+ if (!(isr & XIIC_INTR_BNB_MASK)) {
+ xiic_irq_en(i2c, XIIC_INTR_BNB_MASK);
+ return;
+ }
+
+ ret = read_poll_timeout_atomic(xiic_getreg8, sr,
+ sr & XIIC_SR_BUS_BUSY_MASK, 0, XIIC_BB_TIMEOUT_US, 0,
+ i2c, XIIC_SR_REG_OFFSET);
+
+ if (ret) {
+ dev_err(i2c->dev, "Failed to clear bnb\n");
+ return;
+ }
+
+ xiic_setreg8(i2c, XIIC_IISR_OFFSET, XIIC_INTR_BNB_MASK);
+ xiic_irq_en(i2c, XIIC_INTR_BNB_MASK);
+}
+
/**
* xiic_setclk - Sets the configured clock rate
* @i2c: Pointer to the xiic device structure
@@ -883,9 +909,6 @@ static irqreturn_t xiic_process(int irq, void *dev_id)
}
if (pend & XIIC_INTR_BNB_MASK) {
- /* IIC bus has transitioned to not busy */
- clr |= XIIC_INTR_BNB_MASK;
-
/* The bus is not busy, disable BusNotBusy interrupt */
xiic_irq_dis(i2c, XIIC_INTR_BNB_MASK);
@@ -1030,7 +1053,7 @@ static void xiic_start_recv(struct xiic_i2c *i2c)
xiic_setreg16(i2c, XIIC_DTR_REG_OFFSET, val);
- xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+ xiic_clear_en_bnb(i2c);
} else {
/*
* If previous message is Tx, make sure that Tx FIFO is empty
@@ -1097,7 +1120,7 @@ static void xiic_start_recv(struct xiic_i2c *i2c)
if (i2c->nmsgs == 1)
/* very last, enable bus not busy as well */
- xiic_irq_clr_en(i2c, XIIC_INTR_BNB_MASK);
+ xiic_clear_en_bnb(i2c);
/* the message is tx:ed */
i2c->tx_pos = msg->len;
@@ -1181,11 +1204,11 @@ static void xiic_start_send(struct xiic_i2c *i2c)
/* Clear any pending Tx empty, Tx Error and then enable them */
xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
XIIC_INTR_TX_ERROR_MASK |
- XIIC_INTR_BNB_MASK |
((i2c->nmsgs > 1 || xiic_tx_space(i2c)) ?
XIIC_INTR_TX_HALF_MASK : 0));
xiic_fill_tx_fifo(i2c);
+ xiic_clear_en_bnb(i2c);
} else {
/*
* If previous message is Tx, make sure that Tx FIFO is empty
@@ -1227,8 +1250,9 @@ static void xiic_start_send(struct xiic_i2c *i2c)
/* Clear any pending Tx empty, Tx Error and then enable them */
xiic_irq_clr_en(i2c, XIIC_INTR_TX_EMPTY_MASK |
- XIIC_INTR_TX_ERROR_MASK |
- XIIC_INTR_BNB_MASK);
+ XIIC_INTR_TX_ERROR_MASK);
+
+ xiic_clear_en_bnb(i2c);
}
i2c->prev_msg_tx = true;
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2026-11-19 9:34 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-18 10:11 [RESEND PATCH v4 0/2] i2c: i2c-xiic: fix clearing of bnb irq and waiting/ clearing while atomic Thilo Zirnstein
2026-11-18 10:11 ` [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq Thilo Zirnstein
2026-11-18 13:22 ` Andi Shyti
2026-11-19 9:34 ` Thilo Zirnstein
2026-11-18 10:11 ` [PATCH v4 2/2] i2c: i2c-xiic: fix waiting/clearing while atomic Thilo Zirnstein
-- strict thread matches above, loose matches on Subject: below --
2026-11-02 9:32 [PATCH v4 0/2] i2c: i2c-xiic: fix clearing of bnb irq and waiting/ clearing " Thilo Zirnstein
2026-11-02 9:32 ` [PATCH v4 1/2] i2c: i2c-xiic: fix clearing of bnb irq Thilo Zirnstein
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®