* [PATCH 0/3] Enable RZ/G3L SDHI
@ 2026-11-12 18:48 Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
` (3 more replies)
0 siblings, 4 replies; 6+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
This patch series enable eMMC on SDHI0 and SDHI1 on SDHI2
This patch series is depend upon [1]
[1] https://lore.kernel.org/all/20261104-usb_rzg3l-v8-0-ab109c4bd108@bp.renesas.com/
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
Biju Das (3):
arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0
arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
arch/arm64/boot/dts/renesas/r9a08g046.dtsi | 73 ++++++-
arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts | 89 ++++++++
arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi | 231 +++++++++++++++++++++
3 files changed, 392 insertions(+), 1 deletion(-)
---
base-commit: e7d07f2ed4b4a14f79bc9fb417d25695cb7679a9
change-id: 20261112-sdhi_rzg3l-e0c7dbf7cfdd
Best regards,
--
Biju Das <biju.das.jz@bp.renesas.com>
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
@ 2026-11-12 18:48 ` Biju Das
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
` (2 subsequent siblings)
3 siblings, 0 replies; 6+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
From: Biju Das <biju.das.jz@bp.renesas.com>
Add device tree nodes for the three SDHI controllers (SDHI{0,1,2})
on the RZ/G3L SoC (r9a08g046) and enable SDHI1 on the RZ/G3L SMARC
EVK platform with pincontrol and GPIO-based voltage switching
regulator support.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/r9a08g046.dtsi | 73 +++++++++++++++++-
arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts | 88 ++++++++++++++++++++++
2 files changed, 160 insertions(+), 1 deletion(-)
diff --git a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
index 7e379f6ab837..29ce1ab2a57f 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
+++ b/arch/arm64/boot/dts/renesas/r9a08g046.dtsi
@@ -1062,9 +1062,80 @@ dmac: dma-controller@11820000 {
dma-channels = <16>;
};
+ sdhi0: mmc@11c00000 {
+ compatible = "renesas,sdhi-r9a08g046";
+ reg = <0x0 0x11c00000 0 0x10000>;
+ interrupts = <GIC_SPI 130 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 131 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_CLK_HS>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_IMCLK2>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_IACLKM>,
+ <&cpg CPG_MOD R9A08G046_SDHI0_IACLKS>;
+ clock-names = "core", "clkh", "cd", "aclkm", "aclks";
+ max-frequency = <150000000>;
+ resets = <&cpg R9A08G046_SDHI0_IXRST>,
+ <&cpg R9A08G046_SDHI0_IXRSTAXIM>,
+ <&cpg R9A08G046_SDHI0_IXRSTAXIS>;
+ reset-names = "rst", "axim", "axis";
+ power-domains = <&cpg>;
+ status = "disabled";
+ };
+
sdhi1: mmc@11c10000 {
+ compatible = "renesas,sdhi-r9a08g046";
reg = <0x0 0x11c10000 0 0x10000>;
- /* placeholder */
+ interrupts = <GIC_SPI 132 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 133 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_CLK_HS>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_IMCLK2>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_IACLKM>,
+ <&cpg CPG_MOD R9A08G046_SDHI1_IACLKS>;
+ clock-names = "core", "clkh", "cd", "aclkm", "aclks";
+ max-frequency = <150000000>;
+ resets = <&cpg R9A08G046_SDHI1_IXRST>,
+ <&cpg R9A08G046_SDHI1_IXRSTAXIM>,
+ <&cpg R9A08G046_SDHI1_IXRSTAXIS>;
+ reset-names = "rst", "axim", "axis";
+ power-domains = <&cpg>;
+ status = "disabled";
+
+ sdhi1_vqmmc: vqmmc-regulator {
+ regulator-name = "SDHI1-VQMMC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <1200>;
+ status = "disabled";
+ };
+ };
+
+ sdhi2: mmc@11c20000 {
+ compatible = "renesas,sdhi-r9a08g046";
+ reg = <0x0 0x11c20000 0 0x10000>;
+ interrupts = <GIC_SPI 134 IRQ_TYPE_LEVEL_HIGH>,
+ <GIC_SPI 135 IRQ_TYPE_LEVEL_HIGH>;
+ clocks = <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_CLK_HS>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_IMCLK2>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_IACLKM>,
+ <&cpg CPG_MOD R9A08G046_SDHI2_IACLKS>;
+ clock-names = "core", "clkh", "cd", "aclkm", "aclks";
+ max-frequency = <150000000>;
+ resets = <&cpg R9A08G046_SDHI2_IXRST>,
+ <&cpg R9A08G046_SDHI2_IXRSTAXIM>,
+ <&cpg R9A08G046_SDHI2_IXRSTAXIS>;
+ reset-names = "rst", "axim", "axis";
+ power-domains = <&cpg>;
+ status = "disabled";
+
+ sdhi2_vqmmc: vqmmc-regulator {
+ regulator-name = "SDHI2-VQMMC";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ regulator-ramp-delay = <1200>;
+ status = "disabled";
+ };
};
eth0: ethernet@11c30000 {
diff --git a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
index 9ffaead2c6be..2f3266129733 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
@@ -14,6 +14,7 @@
#define SW_GPIO4 1
#define SW_I3C_EN 0
#define SW_SER0_PMOD 1
+#define SW_SDIO_M2E 0
#define PMOD_GPIO4 0
#define PMOD_GPIO6 0
@@ -38,6 +39,7 @@ / {
aliases {
i2c2 = &i2c2;
i2c3 = &i2c3;
+ mmc1 = &sdhi1;
serial0 = &rsci2;
serial1 = &rsci3;
serial2 = &rsci1;
@@ -69,6 +71,19 @@ codec_dai: codec {
};
};
#endif
+
+#if RZ_BOOT_MODE3
+ vqmmc_sd1_pvdd: regulator-vqmmc-sd1-pvdd {
+ compatible = "regulator-gpio";
+ regulator-name = "SD1_PVDD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&pinctrl RZG3L_GPIO(J, 1) GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <3300000 0>, <1800000 1>;
+ regulator-ramp-delay = <1200>;
+ };
+#endif
};
&i2c2 {
@@ -195,6 +210,68 @@ scif0_pins: scif0 {
power-source = <1800>;
};
+#if RZ_BOOT_MODE3
+ sd1-pwr-en-hog {
+ gpio-hog;
+ gpios = <RZG3L_GPIO(J, 2) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sd1_pwr_en";
+ };
+#endif
+
+ sdhi1_pins: sd1 {
+ sd1-cd {
+ pinmux = <RZG3L_PORT_PINMUX(J, 0, 8)>; /* SD1_CD */
+ };
+
+ sd1-clk {
+ pinmux = <RZG3L_PORT_PINMUX(G, 0, 1)>; /* SD1_CLK */
+ power-source = <3300>;
+ };
+
+ sd1-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(G, 1, 1)>; /* SD1_CMD */
+ input-enable;
+ power-source = <3300>;
+ bias-pull-up;
+ };
+
+ sd1-data {
+ pinmux = <RZG3L_PORT_PINMUX(G, 2, 1)>, /* SD1_DAT0 */
+ <RZG3L_PORT_PINMUX(G, 3, 1)>, /* SD1_DAT1 */
+ <RZG3L_PORT_PINMUX(G, 4, 1)>, /* SD1_DAT2 */
+ <RZG3L_PORT_PINMUX(G, 5, 1)>; /* SD1_DAT3 */
+ input-enable;
+ power-source = <3300>;
+ };
+ };
+
+ sdhi1_uhs_pins: sd1-uhs {
+ sd1-cd {
+ pinmux = <RZG3L_PORT_PINMUX(J, 0, 8)>; /* SD1_CD */
+ };
+
+ sd1-clk {
+ pinmux = <RZG3L_PORT_PINMUX(G, 0, 1)>; /* SD1_CLK */
+ power-source = <1800>;
+ };
+
+ sd1-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(G, 1, 1)>; /* SD1_CMD */
+ input-enable;
+ power-source = <1800>;
+ };
+
+ sd1-data {
+ pinmux = <RZG3L_PORT_PINMUX(G, 2, 1)>, /* SD1_DAT0 */
+ <RZG3L_PORT_PINMUX(G, 3, 1)>, /* SD1_DAT1 */
+ <RZG3L_PORT_PINMUX(G, 4, 1)>, /* SD1_DAT2 */
+ <RZG3L_PORT_PINMUX(G, 5, 1)>; /* SD1_DAT3 */
+ input-enable;
+ power-source = <1800>;
+ };
+ };
+
ssi0_pins: ssi0 {
pinmux = <RZG3L_PORT_PINMUX(H, 0, 9)>, /* SSIF0_RXD */
<RZG3L_PORT_PINMUX(H, 1, 9)>, /* SSIF0_BCK */
@@ -255,6 +332,17 @@ &scif0 {
pinctrl-names = "default";
};
+#if RZ_BOOT_MODE3
+&sdhi1 {
+ pinctrl-0 = <&sdhi1_pins>;
+ pinctrl-1 = <&sdhi1_uhs_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&vqmmc_sd1_pvdd>;
+};
+#endif
+
#if !SW_SD2_EN
&ssi0 {
clocks = <&cpg CPG_MOD R9A08G046_SSI0_PCLK2>,
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
@ 2026-11-12 18:48 ` Biju Das
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
3 siblings, 0 replies; 6+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
From: Biju Das <biju.das.jz@bp.renesas.com>
Add support for enabling SD card or eMMC on SDHI0 on the RZ/G3L SMARC
SoM. The selection between SD and eMMC is controlled by the
SW_SD0_DEV_SEL macro in the board DTS, which must match the position
of switch SYS.1 on the SoM. By default, eMMC is enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts | 1 +
arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi | 143 +++++++++++++++++++++
2 files changed, 144 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
index 2f3266129733..5f5441c47335 100644
--- a/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
+++ b/arch/arm64/boot/dts/renesas/r9a08g046l48-smarc.dts
@@ -9,6 +9,7 @@
/* Switch selection settings */
#define RZ_BOOT_MODE3 1
+#define SW_SD0_DEV_SEL 0
#define SW_SD2_EN 0
#define SW_DPI_EN 0
#define SW_GPIO4 1
diff --git a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
index 91b2d0d43104..e84840fa5086 100644
--- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
@@ -9,6 +9,10 @@
* Please set the below switch position on the SoM and the corresponding macro
* on the board DTS:
*
+ * Switch position SYS.1, Macro SW_SD0_DEV_SEL:
+ * 0 - SD0 is connected to eMMC (default)
+ * 1 - SD0 is connected to uSD0 card
+ *
* Switch position SYS.2, Macro SW_I3C_EN:
* 0 - SMARC_I2C_GP is enabled
* 1 - I3C is enabled
@@ -37,6 +41,7 @@ aliases {
ethernet0 = ð0;
ethernet1 = ð1;
i2c0 = &i2c0;
+ mmc0 = &sdhi0;
};
memory@48000000 {
@@ -78,6 +83,19 @@ reg_3p3v: regulator-3p3v {
regulator-always-on;
};
+#if SW_SD0_DEV_SEL
+ vqmmc_sd0_pvdd: vqmmc-sd0-pvdd {
+ compatible = "regulator-gpio";
+ regulator-name = "SD0_PVDD";
+ regulator-min-microvolt = <1800000>;
+ regulator-max-microvolt = <3300000>;
+ gpios = <&pinctrl RZG3L_GPIO(L, 4) GPIO_ACTIVE_HIGH>;
+ gpios-states = <0>;
+ states = <3300000 0>, <1800000 1>;
+ regulator-ramp-delay = <1200>;
+ };
+#endif
+
x2_clk: x2-clock {
compatible = "fixed-clock";
#clock-cells = <0>;
@@ -241,7 +259,132 @@ i2c0_pins: i2c0 {
pinmux = <RZG3L_PORT_PINMUX(L, 2, 4)>, /* RIIC0_SCL */
<RZG3L_PORT_PINMUX(L, 3, 4)>; /* RIIC0_SDA */
};
+
+ sd0-pwr-en-hog {
+ gpio-hog;
+ gpios = <RZG3L_GPIO(5, 1) GPIO_ACTIVE_HIGH>;
+ output-high;
+ line-name = "sd0_pwr_en";
+ };
+
+ sdhi0_emmc_pins: sd0-emmc {
+ sd0-clk {
+ pins = "SD0_CLK";
+ power-source = <1800>;
+ drive-strength-microamp = <9000>;
+ };
+
+ sd0-cmd {
+ pins = "SD0_CMD";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-data {
+ pins = "SD0_DAT0", "SD0_DAT1", "SD0_DAT2", "SD0_DAT3",
+ "SD0_DAT4", "SD0_DAT5", "SD0_DAT6", "SD0_DAT7";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-rst {
+ pins = "SD0_RST#";
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-ds {
+ pins = "SD0_DS";
+ input-enable;
+ bias-pull-down;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+ };
+
+ sdhi0_usd_pins: sd0-usd {
+ sd0-cd {
+ pinmux = <RZG2L_PORT_PINMUX(5, 0, 8)>; /* SD0_CD */
+ };
+
+ sd0-clk {
+ pins = "SD0_CLK";
+ drive-strength-microamp = <8000>;
+ power-source = <3300>;
+ };
+
+ sd0-cmd {
+ pins = "SD0_CMD";
+ input-enable;
+ drive-strength-microamp = <8000>;
+ power-source = <3300>;
+ };
+
+ sd0-data {
+ pins = "SD0_DAT0", "SD0_DAT1", "SD0_DAT2", "SD0_DAT3";
+ input-enable;
+ drive-strength-microamp = <8000>;
+ power-source = <3300>;
+ };
+ };
+
+ sdhi0_usd_uhs_pins: sd0-usd-uhs {
+ sd0-cd {
+ pinmux = <RZG2L_PORT_PINMUX(5, 0, 8)>; /* SD0_CD */
+ };
+
+ sd0-clk {
+ pins = "SD0_CLK";
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-cmd {
+ pins = "SD0_CMD";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+
+ sd0-data {
+ pins = "SD0_DAT0", "SD0_DAT1", "SD0_DAT2", "SD0_DAT3";
+ input-enable;
+ drive-strength-microamp = <9000>;
+ power-source = <1800>;
+ };
+ };
+};
+
+#if (SW_SD0_DEV_SEL)
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_usd_pins>;
+ pinctrl-1 = <&sdhi0_usd_uhs_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&vqmmc_sd0_pvdd>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+#else
+&sdhi0 {
+ pinctrl-0 = <&sdhi0_emmc_pins>;
+ pinctrl-1 = <&sdhi0_emmc_pins>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <®_1p8v>;
+ bus-width = <8>;
+ mmc-hs200-1_8v;
+ non-removable;
+ fixed-emmc-driver-type = <1>;
+ status = "okay";
};
+#endif
&wdt0 {
timeout-sec = <60>;
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
@ 2026-11-12 18:48 ` Biju Das
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
3 siblings, 0 replies; 6+ messages in thread
From: Biju Das @ 2026-11-12 18:48 UTC (permalink / raw)
To: Geert Uytterhoeven, Magnus Damm, Wolfram Sang, Rob Herring,
Krzysztof Kozlowski, Conor Dooley
Cc: linux-renesas-soc, devicetree, linux-kernel, Biju Das
From: Biju Das <biju.das.jz@bp.renesas.com>
Enable SDHI2 on the RZ/G3L SMARC EVK platform using the internal
voltage regulator for voltage switching. SDHI2 signals are muxed
with I2S0; the selection is controlled by the SW_SD2_EN macro in
the board DTS, which must match the position of switch SYS.4 on
the SoM. By default, I2S0 is enabled.
Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
---
arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi | 88 ++++++++++++++++++++++++
1 file changed, 88 insertions(+)
diff --git a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
index e84840fa5086..a5aec82c0250 100644
--- a/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
+++ b/arch/arm64/boot/dts/renesas/rzg3l-smarc-som.dtsi
@@ -42,6 +42,7 @@ aliases {
ethernet1 = ð1;
i2c0 = &i2c0;
mmc0 = &sdhi0;
+ mmc2 = &sdhi2;
};
memory@48000000 {
@@ -355,6 +356,74 @@ sd0-data {
power-source = <1800>;
};
};
+
+ sdhi2_pins: sd2 {
+ sd2-cd {
+ pinmux = <RZG3L_PORT_PINMUX(K, 0, 1)>; /* SD2_CD */
+ };
+
+ sd2-clk {
+ pinmux = <RZG3L_PORT_PINMUX(H, 0, 1)>; /* SD2_CLK */
+ power-source = <3300>;
+ };
+
+ sd2-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(H, 1, 1)>; /* SD2_CMD */
+ input-enable;
+ power-source = <3300>;
+ };
+
+ sd2-data {
+ pinmux = <RZG3L_PORT_PINMUX(H, 2, 1)>, /* SD2_DAT0 */
+ <RZG3L_PORT_PINMUX(H, 3, 1)>, /* SD2_DAT1 */
+ <RZG3L_PORT_PINMUX(H, 4, 1)>, /* SD2_DAT2 */
+ <RZG3L_PORT_PINMUX(H, 5, 1)>; /* SD2_DAT3 */
+ input-enable;
+ power-source = <3300>;
+ };
+
+ sd2-iovs {
+ pinmux = <RZG3L_PORT_PINMUX(K, 1, 1)>; /* SD2_IOVS */
+ };
+
+ sd2-pwen {
+ pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
+ };
+ };
+
+ sdhi2_pins_uhs: sd2-uhs {
+ sd2-cd {
+ pinmux = <RZG3L_PORT_PINMUX(K, 0, 1)>; /* SD2_CD */
+ };
+
+ sd2-clk {
+ pinmux = <RZG3L_PORT_PINMUX(H, 0, 1)>; /* SD2_CLK */
+ power-source = <1800>;
+ };
+
+ sd2-cmd {
+ pinmux = <RZG3L_PORT_PINMUX(H, 1, 1)>; /* SD2_CMD */
+ input-enable;
+ power-source = <1800>;
+ };
+
+ sd2-data {
+ pinmux = <RZG3L_PORT_PINMUX(H, 2, 1)>, /* SD2_DAT0 */
+ <RZG3L_PORT_PINMUX(H, 3, 1)>, /* SD2_DAT1 */
+ <RZG3L_PORT_PINMUX(H, 4, 1)>, /* SD2_DAT2 */
+ <RZG3L_PORT_PINMUX(H, 5, 1)>; /* SD2_DAT3 */
+ input-enable;
+ power-source = <1800>;
+ };
+
+ sd2-iovs {
+ pinmux = <RZG3L_PORT_PINMUX(K, 1, 1)>; /* SD2_IOVS */
+ };
+
+ sd2-pwen {
+ pinmux = <RZG3L_PORT_PINMUX(K, 2, 1)>; /* SD2_PWEN */
+ };
+ };
};
#if (SW_SD0_DEV_SEL)
@@ -386,6 +455,25 @@ &sdhi0 {
};
#endif
+#if SW_SD2_EN
+&sdhi2 {
+ pinctrl-0 = <&sdhi2_pins>;
+ pinctrl-1 = <&sdhi2_pins_uhs>;
+ pinctrl-names = "default", "state_uhs";
+
+ vmmc-supply = <®_3p3v>;
+ vqmmc-supply = <&sdhi2_vqmmc>;
+ bus-width = <4>;
+ sd-uhs-sdr50;
+ sd-uhs-sdr104;
+ status = "okay";
+};
+
+&sdhi2_vqmmc {
+ status = "okay";
+};
+#endif
+
&wdt0 {
timeout-sec = <60>;
status = "okay";
--
2.43.0
^ permalink raw reply [flat|nested] 6+ messages in thread
* Re: [PATCH 0/3] Enable RZ/G3L SDHI
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
` (2 preceding siblings ...)
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
@ 2026-11-16 10:05 ` Wolfram Sang
2026-11-16 10:09 ` Biju Das
3 siblings, 1 reply; 6+ messages in thread
From: Wolfram Sang @ 2026-11-16 10:05 UTC (permalink / raw)
To: Biju Das
Cc: Geert Uytterhoeven, Magnus Damm, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, linux-renesas-soc, devicetree,
linux-kernel, Biju Das
[-- Attachment #1: Type: text/plain, Size: 430 bytes --]
Hi Biju,
On Thu, Nov 12, 2026 at 06:48:49PM +0000, Biju Das wrote:
> This patch series enable eMMC on SDHI0 and SDHI1 on SDHI2
>
> This patch series is depend upon [1]
> [1] https://lore.kernel.org/all/20261104-usb_rzg3l-v8-0-ab109c4bd108@bp.renesas.com/
>
> Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
could you comment shortly on the Sashiko reports, please?
Thanks and happy hacking,
Wolfram
[-- Attachment #2: signature.asc --]
[-- Type: application/pgp-signature, Size: 833 bytes --]
^ permalink raw reply [flat|nested] 6+ messages in thread
* RE: [PATCH 0/3] Enable RZ/G3L SDHI
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
@ 2026-11-16 10:09 ` Biju Das
0 siblings, 0 replies; 6+ messages in thread
From: Biju Das @ 2026-11-16 10:09 UTC (permalink / raw)
To: wsa+renesas, biju.das.au
Cc: Geert Uytterhoeven, magnus.damm, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, linux-renesas-soc, devicetree,
linux-kernel
Hi Wolfram,
> -----Original Message-----
> From: Wolfram Sang <wsa+renesas@sang-engineering.com>
> Sent: 16 November 2026 10:05
> Subject: Re: [PATCH 0/3] Enable RZ/G3L SDHI
>
> Hi Biju,
>
> On Thu, Nov 12, 2026 at 06:48:49PM +0000, Biju Das wrote:
> > This patch series enable eMMC on SDHI0 and SDHI1 on SDHI2
> >
> > This patch series is depend upon [1]
> > [1] https://lore.kernel.org/all/20261104-usb_rzg3l-v8-0-ab109c4bd108@bp.renesas.com/
> >
> > Signed-off-by: Biju Das <biju.das.jz@bp.renesas.com>
>
> could you comment shortly on the Sashiko reports, please?
Sure.
Cheers,
Biju
^ permalink raw reply [flat|nested] 6+ messages in thread
end of thread, other threads:[~2026-11-16 10:09 UTC | newest]
Thread overview: 6+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-12 18:48 [PATCH 0/3] Enable RZ/G3L SDHI Biju Das
2026-11-12 18:48 ` [PATCH 1/3] arm64: dts: renesas: r9a08g046: Add SDHI nodes for RZ/G3L SoC and SDHI1 pincontrol on SMARC EVK Biju Das
2026-11-12 18:48 ` [PATCH 2/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SD/eMMC on SDHI0 Biju Das
2026-11-12 18:48 ` [PATCH 3/3] arm64: dts: renesas: rzg3l-smarc-som: Enable SDHI2 Biju Das
2026-11-16 10:05 ` [PATCH 0/3] Enable RZ/G3L SDHI Wolfram Sang
2026-11-16 10:09 ` Biju Das
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®