From: Nikita Travkin <nikita@trvn.ru>
To: Stephan Gerhold <stephan@gerhold.net>
Cc: Pavel Machek <pavel@ucw.cz>, Lee Jones <lee@kernel.org>,
Rob Herring <robh+dt@kernel.org>,
Krzysztof Kozlowski <krzysztof.kozlowski+dt@linaro.org>,
Conor Dooley <conor+dt@kernel.org>,
linux-leds@vger.kernel.org, devicetree@vger.kernel.org,
linux-kernel@vger.kernel.org, "Lin,
Meng-Bo" <linmengbo0689@protonmail.com>
Subject: Re: [PATCH v3 0/3] leds: aw2013: Document interrupt and pull-up supply
Date: Wed, 16 Aug 2023 10:38:29 +0500 [thread overview]
Message-ID: <b16899c6673a34b69ce5903f5372d0ba@trvn.ru> (raw)
In-Reply-To: <20230815-aw2013-vio-v3-0-2505296b0856@gerhold.net>
Stephan Gerhold писал(а) 15.08.2023 22:21:
> AW2013 has an optional interrupt pin "INTN" which is used to report
> completion of started operations (e.g. power up or LED breath effects).
> The driver does not use it (yet) but it should be already described for
> completeness inside the DT schema.
>
> Since the interrupt and I2C lines operate in open drain low active mode
> a pull-up supply is needed for correct operation. Unfortunately there
> is no ideal place to describe it in the DT: The pull-up needed for the
> I2C lines could be described on the I2C bus. However, the pull-up
> needed for the interrupt line belongs neither directly to the interrupt
> controller nor to AW2013. Since the AW2013 driver will be typically in
> control of the power management and interrupt masking it makes more
> sense to describe it inside the AW2013 device tree node.
>
Oh indeed, seems like even on the hardware I was initially targeting,
the pull is tied to a regulator, I probably missed it because it was
always on. Thank you both for adding that and fixing up the bindings!
Reviewed-by: Nikita Travkin <nikita@trvn.ru>
Nikita
> Changes in v3:
> - Rewrite commit messages based on discussion on v2
> - Also document missing interrupt in DT schema (new patch)
>
> Discussion on v2:
> https://lore.kernel.org/linux-leds/20230321220825.GA1685482-robh@kernel.org/
>
> Signed-off-by: Stephan Gerhold <stephan@gerhold.net>
> ---
> Lin, Meng-Bo (1):
> leds: aw2013: Enable pull-up supply for interrupt and I2C
>
> Stephan Gerhold (2):
> dt-bindings: leds: aw2013: Document interrupt
> dt-bindings: leds: Document pull-up supply for interrupt and I2C
>
> .../devicetree/bindings/leds/leds-aw2013.yaml | 13 ++++++++
> drivers/leds/leds-aw2013.c | 36 +++++++++++++---------
> 2 files changed, 35 insertions(+), 14 deletions(-)
> ---
> base-commit: 841165267827955bb3295b066cb6a906ba9265c0
> change-id: 20230815-aw2013-vio-92a4566c5863
>
> Best regards,
next prev parent reply other threads:[~2023-08-16 5:39 UTC|newest]
Thread overview: 8+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-08-15 17:21 Stephan Gerhold
2023-08-15 17:21 ` [PATCH v3 1/3] dt-bindings: leds: aw2013: Document interrupt Stephan Gerhold
2023-08-15 20:31 ` Krzysztof Kozlowski
2023-08-15 17:21 ` [PATCH v3 2/3] dt-bindings: leds: Document pull-up supply for interrupt and I2C Stephan Gerhold
2023-08-15 20:31 ` Krzysztof Kozlowski
2023-08-15 17:21 ` [PATCH v3 3/3] leds: aw2013: Enable " Stephan Gerhold
2023-08-16 5:38 ` Nikita Travkin [this message]
2023-08-18 15:47 ` [PATCH v3 0/3] leds: aw2013: Document interrupt and pull-up supply Lee Jones
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=b16899c6673a34b69ce5903f5372d0ba@trvn.ru \
--to=nikita@trvn.ru \
--cc=conor+dt@kernel.org \
--cc=devicetree@vger.kernel.org \
--cc=krzysztof.kozlowski+dt@linaro.org \
--cc=lee@kernel.org \
--cc=linmengbo0689@protonmail.com \
--cc=linux-kernel@vger.kernel.org \
--cc=linux-leds@vger.kernel.org \
--cc=pavel@ucw.cz \
--cc=robh+dt@kernel.org \
--cc=stephan@gerhold.net \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®