[PATCH v3 0/6] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[PATCH v3 0/6] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[Jens Glathe via B4 Relay]

Device tree for the Lenovo Thinkbook 16 G7 QOY

The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].

Supported features:

- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera

Not supported yet:

- HDMI port.
- EC and some fn hotkeys.

Limited support yet:

- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.

- The GPU is not yet supported. Graphics is only software rendered.

This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1 device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).

I have brought up the Thinkbook over the last 4 months since the x1p42100-crd
patches were available. The laptop is very usable now, and quite solid as a dev/
test platform. GPU support would be nice, though :)

Big thanks to Aleksandrs Vinarskis for helping (and sort of persisting) on the
fingerprint, camera and HDMI issues.

[1]: https://psref.lenovo.com/syspool/Sys/PDF/ThinkBook/ThinkBook_16_G7_QOY/ThinkBook_16_G7_QOY_Spec.pdf

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
Changes in v3:
- removed changes in x1e80100.dtsi and x1p42100.dtsi - resolved with [2]
- fixed schema errors with correct compatible string for the model
- added power management for the camera via onboard_usb_dev.c
- amended node ordering
- changed the panel driver used to edp-panel, added panel in the driver
- amended x1e80100.dtsi for exposing PM8010: This one is not present in the design, 
  added /delete-node/ for it.
- removed commented-out lines for sdhc, specified which don't work.
- corrected ZAP shader firmware name
- Link to v2: https://lore.kernel.org/r/20250516-tb16-dt-v2-0-7c4996d58ed6@oldschoolsolutions.biz

Changes in v2:
- removed nodes that gave DTC compile errors (pm8010_thermal, edp0_hpd_active)
- amended qcom.yaml
- shortened the commit titles to fit 75 chars
- Link to v1: https://lore.kernel.org/r/20250515-tb16-dt-v1-0-dc5846a25c48@oldschoolsolutions.biz

[2]: 20250520-topic-x1p4_tsens-v2-1-9687b789a4fb@oss.qualcomm.com

---
Jens Glathe (6):
      dt-bindings: arm: qcom: Add Lenovo TB16 support
      drm/panel-edp: add N160JCE-ELL CMN panel for Lenovo Thinkbook 16
      usb: misc: onboard_usb_dev: Add Bison Electronics Inc. Integrated Camera
      firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16
      arm64: dts: qcom: x1p42100: Add Lenovo ThinkBook 16 G7 QOY
      arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

 Documentation/devicetree/bindings/arm/qcom.yaml    |    1 +
 arch/arm64/boot/dts/qcom/Makefile                  |    3 +
 arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi       |    2 +-
 .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1655 ++++++++++++++++++++
 drivers/firmware/qcom/qcom_scm.c                   |    1 +
 drivers/gpu/drm/panel/panel-edp.c                  |    1 +
 drivers/usb/misc/onboard_usb_dev.c                 |    2 +
 drivers/usb/misc/onboard_usb_dev.h                 |    8 +
 8 files changed, 1672 insertions(+), 1 deletion(-)
---
base-commit: 176e917e010cb7dcc605f11d2bc33f304292482b
change-id: 20250511-tb16-dt-e84c433d87b1

Best regards,
-- 
Jens Glathe <jens.glathe@oldschoolsolutions.biz>

[PATCH v3 1/6] dt-bindings: arm: qcom: Add Lenovo TB16 support

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Document the x1p-42-100/x1-26-100 variants of the Thinkbook 16 G7 QOY.

[1]: https://psref.lenovo.com/syspool/Sys/PDF/ThinkBook/ThinkBook_16_G7_QOY/ThinkBook_16_G7_QOY_Spec.pdf

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 56f78f0f3803fedcb6422efd6adec3bbc81c2e03..5654aaf825955f8000355600c0ae35b74676273e 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -1153,6 +1153,7 @@ properties:
       - items:
           - enum:
               - asus,zenbook-a14-ux3407qa
+              - lenovo,thinkbook-16
               - qcom,x1p42100-crd
           - const: qcom,x1p42100
 

-- 
2.48.1

[PATCH v3 2/6] drm/panel-edp: add N160JCE-ELL CMN panel for Lenovo Thinkbook 16

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Panel is widely used in 16" laptops, and also in my Thinkbook 16 G7 QOY.

CMN N160JCE-ELL EDID
edid-decode (hex):

00 ff ff ff ff ff ff 00 0d ae 2b 16 00 00 00 00
20 20 01 04 a5 22 16 78 03 28 65 97 59 54 8e 27
1e 50 54 00 00 00 01 01 01 01 01 01 01 01 01 01
01 01 01 01 01 01 42 3c 80 a0 70 b0 24 40 30 20
a6 00 58 d7 10 00 00 18 35 30 80 a0 70 b0 24 40
30 20 a6 00 58 d7 10 00 00 18 00 00 00 fd 00 28
3c 4b 4b 10 01 0a 20 20 20 20 20 20 00 00 00 fe
00 4e 31 36 30 4a 43 45 2d 45 4c 4c 0a 20 00 95

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/gpu/drm/panel/panel-edp.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/gpu/drm/panel/panel-edp.c b/drivers/gpu/drm/panel/panel-edp.c
index 90e8c154a9788ad40e2101fdf39cbd92f2e0773a..ec9622e0a313f4a228618f119e2aaa812f63d5a4 100644
--- a/drivers/gpu/drm/panel/panel-edp.c
+++ b/drivers/gpu/drm/panel/panel-edp.c
@@ -1973,6 +1973,7 @@ static const struct edp_panel_entry edp_panels[] = {
 	EDP_PANEL_ENTRY('C', 'M', 'N', 0x14d4, &delay_200_500_e80_d50, "N140HCA-EAC"),
 	EDP_PANEL_ENTRY('C', 'M', 'N', 0x14d6, &delay_200_500_e80_d50, "N140BGA-EA4"),
 	EDP_PANEL_ENTRY('C', 'M', 'N', 0x14e5, &delay_200_500_e80_d50, "N140HGA-EA1"),
+	EDP_PANEL_ENTRY('C', 'M', 'N', 0x162b, &delay_200_500_e80_d50, "N160JCE-ELL"),
 
 	EDP_PANEL_ENTRY('C', 'S', 'O', 0x1200, &delay_200_500_e50_p2e200, "MNC207QS1-1"),
 	EDP_PANEL_ENTRY('C', 'S', 'O', 0x1413, &delay_200_500_e50_p2e200, "MNE007JA1-2"),

-- 
2.48.1

[PATCH v3 3/6] usb: misc: onboard_usb_dev: Add Bison Electronics Inc. Integrated Camera

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

The Camera is built into the Thinkbook 16 G7 QOY and directly attached on the
usb_2 controller (dwc3 USB2 only). It has a separate power supply that needs
to be controlled for PM.

Add the support for this device for the power supply.

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/usb/misc/onboard_usb_dev.c | 2 ++
 drivers/usb/misc/onboard_usb_dev.h | 8 ++++++++
 2 files changed, 10 insertions(+)

diff --git a/drivers/usb/misc/onboard_usb_dev.c b/drivers/usb/misc/onboard_usb_dev.c
index 1048e3912068ced166c76838cf7306d86e192fe4..17b1f345b6b65bf25e68e77b0a345936825e1d04 100644
--- a/drivers/usb/misc/onboard_usb_dev.c
+++ b/drivers/usb/misc/onboard_usb_dev.c
@@ -569,6 +569,7 @@ static struct platform_driver onboard_dev_driver = {
 #define VENDOR_ID_TI		0x0451
 #define VENDOR_ID_VIA		0x2109
 #define VENDOR_ID_XMOS		0x20B1
+#define VENDOR_ID_BISON		0x5986
 
 /*
  * Returns the onboard_dev platform device that is associated with the USB
@@ -677,6 +678,7 @@ static const struct usb_device_id onboard_dev_id_table[] = {
 	{ USB_DEVICE(VENDOR_ID_VIA, 0x0817) }, /* VIA VL817 3.1 HUB */
 	{ USB_DEVICE(VENDOR_ID_VIA, 0x2817) }, /* VIA VL817 2.0 HUB */
 	{ USB_DEVICE(VENDOR_ID_XMOS, 0x0013) }, /* XMOS XVF3500 Voice Processor */
+	{ USB_DEVICE(VENDOR_ID_BISON, 0x1198) }, /* Bison Electronics Inc. Integrated Camera */
 	{}
 };
 MODULE_DEVICE_TABLE(usb, onboard_dev_id_table);
diff --git a/drivers/usb/misc/onboard_usb_dev.h b/drivers/usb/misc/onboard_usb_dev.h
index e017b8e22f936be66da73789abb4f620e6af4d6a..816d9ce71eaddc7ab0cb4517558dd44a591d6c28 100644
--- a/drivers/usb/misc/onboard_usb_dev.h
+++ b/drivers/usb/misc/onboard_usb_dev.h
@@ -115,6 +115,13 @@ static const struct onboard_dev_pdata xmos_xvf3500_data = {
 	.is_hub = false,
 };
 
+static const struct onboard_dev_pdata bison_intcamera_data = {
+	.reset_us = 1000,
+	.num_supplies = 1,
+	.supply_names = { "vdd" },
+	.is_hub = false,
+};
+
 static const struct of_device_id onboard_dev_match[] = {
 	{ .compatible = "usb424,2412", .data = &microchip_usb424_data, },
 	{ .compatible = "usb424,2514", .data = &microchip_usb2514_data, },
@@ -144,6 +151,7 @@ static const struct of_device_id onboard_dev_match[] = {
 	{ .compatible = "usb2109,817", .data = &vialab_vl817_data, },
 	{ .compatible = "usb2109,2817", .data = &vialab_vl817_data, },
 	{ .compatible = "usb20b1,0013", .data = &xmos_xvf3500_data, },
+	{ .compatible = "usb5986,1198", .data = &bison_intcamera_data, },
 	{}
 };
 

-- 
2.48.1

[PATCH v3 4/6] firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Allow particular machine accessing eg. efivars.

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 drivers/firmware/qcom/qcom_scm.c | 1 +
 1 file changed, 1 insertion(+)

diff --git a/drivers/firmware/qcom/qcom_scm.c b/drivers/firmware/qcom/qcom_scm.c
index f63b716be5b027550ae3a987e784f0814ea6d678..171cc2a6502463e3445919ef77a129563ea233a4 100644
--- a/drivers/firmware/qcom/qcom_scm.c
+++ b/drivers/firmware/qcom/qcom_scm.c
@@ -1993,6 +1993,7 @@ static const struct of_device_id qcom_scm_qseecom_allowlist[] __maybe_unused = {
 	{ .compatible = "hp,omnibook-x14" },
 	{ .compatible = "huawei,gaokun3" },
 	{ .compatible = "lenovo,flex-5g" },
+	{ .compatible = "lenovo,thinkbook-16" },
 	{ .compatible = "lenovo,thinkpad-t14s" },
 	{ .compatible = "lenovo,thinkpad-x13s", },
 	{ .compatible = "lenovo,yoga-slim7x" },

-- 
2.48.1

[PATCH v3 5/6] arm64: dts: qcom: x1p42100: Add Lenovo ThinkBook 16 G7 QOY

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

The Thinkbook 16 appears to be an X1 / X1 Plus only design.
Add make targets for normal and -el2 variant.

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
---
 arch/arm64/boot/dts/qcom/Makefile | 3 +++
 1 file changed, 3 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
index 669b888b27a1daa93ac15f47e8b9a302bb0922c2..aff4fe3e81ec0d6f6d52e2aa0da327b7576632d8 100644
--- a/arch/arm64/boot/dts/qcom/Makefile
+++ b/arch/arm64/boot/dts/qcom/Makefile
@@ -327,3 +327,6 @@ x1e80100-qcp-el2-dtbs	:= x1e80100-qcp.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-qcp.dtb x1e80100-qcp-el2.dtb
 x1p42100-crd-el2-dtbs	:= x1p42100-crd.dtb x1-el2.dtbo
 dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-crd.dtb x1p42100-crd-el2.dtb
+x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
+dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
+

-- 
2.48.1

[PATCH v3 6/6] arm64: dts: qcom: Add Lenovo ThinkBook 16 device tree

[Jens Glathe via B4 Relay]

From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>

Device tree for the Lenovo Thinkbook 16 G7 QOY

The Laptop is a Snapdragon X1 / X1 Plus (Purwa) based device [1].

Supported features:

- USB type-c and type-a ports
- Keyboard
- Touchpad (all that are described in the dsdt)
- Touchscreen (described in the dsdt, no known SKUss)
- Display including PWM backlight control
- PCIe devices
- nvme
- SDHC card reader
- ath12k WCN7850 Wifi and Bluetooth
- ADSP and CDSP
- GPIO keys (Lid switch)
- Sound via internal speakers / DMIC / USB / headphone jack
- DP Altmode with 2 lanes (as all of these still do)
- Integrated fingerprint reader (FPC)
- Integrated UVC camera

Not supported yet:

- HDMI port.
- EC and some fn hotkeys.

Limited support yet:

- SDHC card reader is based on the on-chip sdhc_2 controller, but the driver from
the Snapdragon Dev Kit is only a partial match. It can do normal slow sd cards,
but not UHS-I (SD104) and UHS-II.

- The GPU is not yet supported. Graphics is only software rendered.

This work was done without any schematics or non-public knowledge of the device.
So, it is based on the existing x1e device trees, dsdt analysis, using HWInfo
ARM64, and pure guesswork. It has been confirmed, however, that the device really
has 4 NXP PTN3222 eUSB2 repeaters, one of which doesn't have a reset GPIO (eusb5
@43).

Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
Co-developed by: Aleksandrs Vinarskis <alex.vinarskis@gmail.com>
---
 arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi       |    2 +-
 .../boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts | 1655 ++++++++++++++++++++
 2 files changed, 1656 insertions(+), 1 deletion(-)

diff --git a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
index c02fd4d15c9649c222caaafa5ed2c777a10fb4f5..551b392eca4ef3b6041e03ad1385fef11cec1690 100644
--- a/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1e80100-pmics.dtsi
@@ -170,7 +170,7 @@ trip1 {
 			};
 		};
 
-		pm8010-thermal {
+		pm8010_thermal: pm8010-thermal {
 			polling-delay-passive = <100>;
 
 			thermal-sensors = <&pm8010_temp_alarm>;
diff --git a/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
new file mode 100644
index 0000000000000000000000000000000000000000..7089219ed08c1c4a60cc007f9d043a34a8071b4f
--- /dev/null
+++ b/arch/arm64/boot/dts/qcom/x1p42100-lenovo-thinkbook-16.dts
@@ -0,0 +1,1655 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2023 Qualcomm Innovation Center, Inc. All rights reserved.
+ * Copyright (c) 2024, Linaro Limited
+ * Copyright (c) 2025, Jens Glathe
+ */
+
+/dts-v1/;
+
+#include <dt-bindings/gpio/gpio.h>
+#include <dt-bindings/input/gpio-keys.h>
+#include <dt-bindings/input/input.h>
+#include <dt-bindings/pinctrl/qcom,pmic-gpio.h>
+#include <dt-bindings/regulator/qcom,rpmh-regulator.h>
+
+#include "x1p42100.dtsi"
+#include "x1e80100-pmics.dtsi"
+
+/delete-node/ &pmc8380_6;
+/delete-node/ &pmc8380_6_thermal;
+/delete-node/ &pm8010;
+/delete-node/ &pm8010_thermal;
+
+/ {
+	model = "Lenovo ThinkBook 16 Gen 7 QOY";
+	compatible = "lenovo,thinkbook-16", "qcom,x1p42100";
+	chassis-type = "laptop";
+
+	aliases {
+		serial0 = &uart21;
+		serial1 = &uart14;
+	};
+
+	wcd938x: audio-codec {
+		compatible = "qcom,wcd9385-codec";
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&wcd_default>;
+
+		qcom,micbias1-microvolt = <1800000>;
+		qcom,micbias2-microvolt = <1800000>;
+		qcom,micbias3-microvolt = <1800000>;
+		qcom,micbias4-microvolt = <1800000>;
+		qcom,mbhc-buttons-vthreshold-microvolt = <75000 150000 237000 500000 500000 500000 500000 500000>;
+		qcom,mbhc-headset-vthreshold-microvolt = <1700000>;
+		qcom,mbhc-headphone-vthreshold-microvolt = <50000>;
+		qcom,rx-device = <&wcd_rx>;
+		qcom,tx-device = <&wcd_tx>;
+
+		reset-gpios = <&tlmm 191 GPIO_ACTIVE_LOW>;
+
+		vdd-buck-supply = <&vreg_l15b_1p8>;
+		vdd-rxtx-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l15b_1p8>;
+		vdd-mic-bias-supply = <&vreg_bob1>;
+
+		#sound-dai-cells = <1>;
+	};
+
+	backlight: backlight {
+		compatible = "pwm-backlight";
+		pwms = <&pm8550_pwm 3 500000>;
+
+		power-supply = <&vreg_edp_bl>;
+	};
+
+	camera {
+		compatible = "usb5986,1198";
+
+		vdd-supply = <&vreg_cam_5p0>;
+
+		status = "okay";
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+
+		pinctrl-0 = <&hall_int_n_default>;
+		pinctrl-names = "default";
+
+		switch-lid {
+			gpios = <&tlmm 92 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			wakeup-source;
+			wakeup-event-action = <EV_ACT_DEASSERTED>;
+		};
+	};
+
+	pmic-glink {
+		compatible = "qcom,x1e80100-pmic-glink",
+				"qcom,sm8550-pmic-glink",
+				"qcom,pmic-glink";
+		#address-cells = <1>;
+		#size-cells = <0>;
+		orientation-gpios = <&tlmm 121 GPIO_ACTIVE_HIGH>,
+				<&tlmm 123 GPIO_ACTIVE_HIGH>;
+
+		/* Display-adjacent port */
+		connector@0 {
+			compatible = "usb-c-connector";
+			reg = <0>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss0_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss0_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss0_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss0_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss0_sbu_mux>;
+					};
+				};
+			};
+		};
+
+		/* User-adjacent port */
+		connector@1 {
+			compatible = "usb-c-connector";
+			reg = <1>;
+			power-role = "dual";
+			data-role = "dual";
+
+			ports {
+				#address-cells = <1>;
+				#size-cells = <0>;
+
+				port@0 {
+					reg = <0>;
+
+					pmic_glink_ss1_hs_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_dwc3_hs>;
+					};
+				};
+
+				port@1 {
+					reg = <1>;
+
+					pmic_glink_ss1_ss_in: endpoint {
+						remote-endpoint = <&usb_1_ss1_qmpphy_out>;
+					};
+				};
+
+				port@2 {
+					reg = <2>;
+
+					pmic_glink_ss1_sbu: endpoint {
+						remote-endpoint = <&usb_1_ss1_sbu_mux>;
+					};
+				};
+			};
+		};
+	};
+
+	reserved-memory {
+		linux,cma {
+			compatible = "shared-dma-pool";
+			size = <0x0 0x8000000>;
+			reusable;
+			linux,cma-default;
+		};
+	};
+
+	sound {
+		compatible = "qcom,x1e80100-sndcard";
+		model = "X1E80100-LENOVO-ThinkBook-16";
+		audio-routing = "SpkrLeft IN", "WSA WSA_SPK1 OUT",
+				"SpkrRight IN", "WSA WSA_SPK2 OUT",
+				"IN1_HPHL", "HPHL_OUT",
+				"IN2_HPHR", "HPHR_OUT",
+				"AMIC2", "MIC BIAS2",
+				"VA DMIC0", "MIC BIAS3",
+				"VA DMIC1", "MIC BIAS3",
+				"VA DMIC2", "MIC BIAS1",
+				"VA DMIC3", "MIC BIAS1",
+				"VA DMIC0", "VA MIC BIAS3",
+				"VA DMIC1", "VA MIC BIAS3",
+				"VA DMIC2", "VA MIC BIAS1",
+				"VA DMIC3", "VA MIC BIAS1",
+				"TX SWR_INPUT1", "ADC2_OUTPUT";
+
+		wcd-playback-dai-link {
+			link-name = "WCD Playback";
+
+			cpu {
+				sound-dai = <&q6apmbedai RX_CODEC_DMA_RX_0>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 0>, <&swr1 0>, <&lpass_rxmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wcd-capture-dai-link {
+			link-name = "WCD Capture";
+
+			cpu {
+				sound-dai = <&q6apmbedai TX_CODEC_DMA_TX_3>;
+			};
+
+			codec {
+				sound-dai = <&wcd938x 1>, <&swr2 1>, <&lpass_txmacro 0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		wsa-dai-link {
+			link-name = "WSA Playback";
+
+			codec {
+				sound-dai = <&left_spkr>, <&right_spkr>, <&swr0 0>, <&lpass_wsamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai WSA_CODEC_DMA_RX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+
+		va-dai-link {
+			link-name = "VA Capture";
+
+			codec {
+				sound-dai = <&lpass_vamacro 0>;
+			};
+
+			cpu {
+				sound-dai = <&q6apmbedai VA_CODEC_DMA_TX_0>;
+			};
+
+			platform {
+				sound-dai = <&q6apm>;
+			};
+		};
+	};
+
+	usb-1-ss0-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 168 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 167 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss0_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss0_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss0_sbu>;
+			};
+		};
+	};
+
+	usb-1-ss1-sbu-mux {
+		compatible = "onnn,fsusb42", "gpio-sbu-mux";
+
+		enable-gpios = <&tlmm 179 GPIO_ACTIVE_LOW>;
+		select-gpios = <&tlmm 178 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&usb_1_ss1_sbu_default>;
+		pinctrl-names = "default";
+
+		mode-switch;
+		orientation-switch;
+
+		port {
+			usb_1_ss1_sbu_mux: endpoint {
+				remote-endpoint = <&pmic_glink_ss1_sbu>;
+			};
+		};
+	};
+
+	vreg_cam_5p0: regulator-cam-5p0 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_CAM_5P0";
+		regulator-min-microvolt = <5000000>;
+		regulator-max-microvolt = <5000000>;
+
+		gpio = <&tlmm 44 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&cam_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_3p3: regulator-edp-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_EDP_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 70 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&edp_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_edp_bl: regulator-edp-bl {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VBL9";
+		regulator-min-microvolt = <3600000>;
+		regulator-max-microvolt = <3600000>;
+
+		gpio = <&pmc8380_3_gpios 10 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&edp_bl_reg_en>;
+
+		regulator-boot-on;
+	};
+
+	vreg_misc_3p3: regulator-misc-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_MISC_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&pm8550ve_8_gpios 6 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-names = "default";
+		pinctrl-0 = <&misc_3p3_reg_en>;
+
+		regulator-boot-on;
+		regulator-always-on;
+	};
+
+	vreg_nvme: regulator-nvme {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_NVME_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 18 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&nvme_reg_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vreg_wcn_0p95: regulator-wcn-0p95 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_0P95";
+		regulator-min-microvolt = <950000>;
+		regulator-max-microvolt = <950000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_1p9: regulator-wcn-1p9 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_1P9";
+		regulator-min-microvolt = <1900000>;
+		regulator-max-microvolt = <1900000>;
+
+		vin-supply = <&vreg_wcn_3p3>;
+	};
+
+	vreg_wcn_3p3: regulator-wcn-3p3 {
+		compatible = "regulator-fixed";
+
+		regulator-name = "VREG_WCN_3P3";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		gpio = <&tlmm 214 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&wcn_sw_en>;
+		pinctrl-names = "default";
+
+		regulator-boot-on;
+	};
+
+	vph_pwr: regulator-vph-pwr {
+		compatible = "regulator-fixed";
+
+		regulator-name = "vph_pwr";
+		regulator-min-microvolt = <3700000>;
+		regulator-max-microvolt = <3700000>;
+
+		regulator-always-on;
+		regulator-boot-on;
+	};
+
+	wcn7850-pmu {
+		compatible = "qcom,wcn7850-pmu";
+
+		vdd-supply = <&vreg_wcn_0p95>;
+		vddio-supply = <&vreg_l15b_1p8>;
+		vddaon-supply = <&vreg_wcn_0p95>;
+		vdddig-supply = <&vreg_wcn_0p95>;
+		vddrfa1p2-supply = <&vreg_wcn_1p9>;
+		vddrfa1p8-supply = <&vreg_wcn_1p9>;
+
+		wlan-enable-gpios = <&tlmm 117 GPIO_ACTIVE_HIGH>;
+		bt-enable-gpios = <&tlmm 116 GPIO_ACTIVE_HIGH>;
+
+		pinctrl-0 = <&wcn_wlan_en>;
+		pinctrl-1 = <&wcn_bt_en>;
+		pinctrl-names = "default";
+
+		regulators {
+			vreg_pmu_rfa_cmn: ldo0 {
+				regulator-name = "vreg_pmu_rfa_cmn";
+			};
+
+			vreg_pmu_aon_0p59: ldo1 {
+				regulator-name = "vreg_pmu_aon_0p59";
+			};
+
+			vreg_pmu_wlcx_0p8: ldo2 {
+				regulator-name = "vreg_pmu_wlcx_0p8";
+			};
+
+			vreg_pmu_wlmx_0p85: ldo3 {
+				regulator-name = "vreg_pmu_wlmx_0p85";
+			};
+
+			vreg_pmu_btcmx_0p85: ldo4 {
+				regulator-name = "vreg_pmu_btcmx_0p85";
+			};
+
+			vreg_pmu_rfa_0p8: ldo5 {
+				regulator-name = "vreg_pmu_rfa_0p8";
+			};
+
+			vreg_pmu_rfa_1p2: ldo6 {
+				regulator-name = "vreg_pmu_rfa_1p2";
+			};
+
+			vreg_pmu_rfa_1p8: ldo7 {
+				regulator-name = "vreg_pmu_rfa_1p8";
+			};
+
+			vreg_pmu_pcie_0p9: ldo8 {
+				regulator-name = "vreg_pmu_pcie_0p9";
+			};
+
+			vreg_pmu_pcie_1p8: ldo9 {
+				regulator-name = "vreg_pmu_pcie_1p8";
+			};
+		};
+	};
+};
+
+&apps_rsc {
+	regulators-0 {
+		compatible = "qcom,pm8550-rpmh-regulators";
+		qcom,pmic-id = "b";
+
+		vdd-bob1-supply = <&vph_pwr>;
+		vdd-bob2-supply = <&vph_pwr>;
+		vdd-l1-l4-l10-supply = <&vreg_s4c_1p8>;
+		vdd-l2-l13-l14-supply = <&vreg_bob1>;
+		vdd-l5-l16-supply = <&vreg_bob1>;
+		vdd-l6-l7-supply = <&vreg_bob2>;
+		vdd-l8-l9-supply = <&vreg_bob1>;
+		vdd-l12-supply = <&vreg_s5j_1p2>;
+		vdd-l15-supply = <&vreg_s4c_1p8>;
+		vdd-l17-supply = <&vreg_bob2>;
+
+		vreg_bob1: bob1 {
+			regulator-name = "vreg_bob1";
+			regulator-min-microvolt = <3008000>;
+			regulator-max-microvolt = <3960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_bob2: bob2 {
+			regulator-name = "vreg_bob2";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <3008000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1b_1p8: ldo1 {
+			regulator-name = "vreg_l1b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2b_3p0: ldo2 {
+			regulator-name = "vreg_l2b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l4b_1p8: ldo4 {
+			regulator-name = "vreg_l4b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l5b_3p0: ldo5 {
+			regulator-name = "vreg_l5b_3p0";
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l6b_1p8: ldo6 {
+			regulator-name = "vreg_l6b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l7b_2p8: ldo7 {
+			regulator-name = "vreg_l7b_2p8";
+			regulator-min-microvolt = <2800000>;
+			regulator-max-microvolt = <2800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l8b_3p0: ldo8 {
+			regulator-name = "vreg_l8b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l9b_2p9: ldo9 {
+			regulator-name = "vreg_l9b_2p9";
+			regulator-min-microvolt = <2960000>;
+			regulator-max-microvolt = <2960000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l10b_1p8: ldo10 {
+			regulator-name = "vreg_l10b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l12b_1p2: ldo12 {
+			regulator-name = "vreg_l12b_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l13b_3p0: ldo13 {
+			regulator-name = "vreg_l13b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l14b_3p0: ldo14 {
+			regulator-name = "vreg_l14b_3p0";
+			regulator-min-microvolt = <3072000>;
+			regulator-max-microvolt = <3072000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l15b_1p8: ldo15 {
+			regulator-name = "vreg_l15b_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l16b_2p9: ldo16 {
+			regulator-name = "vreg_l16b_2p9";
+			regulator-min-microvolt = <2912000>;
+			regulator-max-microvolt = <2912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l17b_2p5: ldo17 {
+			regulator-name = "vreg_l17b_2p5";
+			regulator-min-microvolt = <2504000>;
+			regulator-max-microvolt = <2504000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-1 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "c";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s4-supply = <&vph_pwr>;
+
+		vreg_s4c_1p8: smps4 {
+			regulator-name = "vreg_s4c_1p8";
+			regulator-min-microvolt = <1856000>;
+			regulator-max-microvolt = <2000000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1c_1p2: ldo1 {
+			regulator-name = "vreg_l1c_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2c_0p8: ldo2 {
+			regulator-name = "vreg_l2c_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3c_0p8: ldo3 {
+			regulator-name = "vreg_l3c_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-2 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "d";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s4c_1p8>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_l1d_0p8: ldo1 {
+			regulator-name = "vreg_l1d_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2d_0p9: ldo2 {
+			regulator-name = "vreg_l2d_0p9";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3d_1p8: ldo3 {
+			regulator-name = "vreg_l3d_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-3 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "e";
+
+		vdd-l2-supply = <&vreg_s1f_0p7>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+
+		vreg_l2e_0p8: ldo2 {
+			regulator-name = "vreg_l2e_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3e_1p2: ldo3 {
+			regulator-name = "vreg_l3e_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-4 {
+		compatible = "qcom,pmc8380-rpmh-regulators";
+		qcom,pmic-id = "f";
+
+		vdd-l1-supply = <&vreg_s5j_1p2>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s5j_1p2>;
+		vdd-s1-supply = <&vph_pwr>;
+
+		vreg_s1f_0p7: smps1 {
+			regulator-name = "vreg_s1f_0p7";
+			regulator-min-microvolt = <700000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1f_1p0: ldo1 {
+			regulator-name = "vreg_l1f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2f_1p0: ldo2 {
+			regulator-name = "vreg_l2f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3f_1p0: ldo3 {
+			regulator-name = "vreg_l3f_1p0";
+			regulator-min-microvolt = <1024000>;
+			regulator-max-microvolt = <1024000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-6 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "i";
+
+		vdd-l1-supply = <&vreg_s4c_1p8>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s1-supply = <&vph_pwr>;
+		vdd-s2-supply = <&vph_pwr>;
+
+		vreg_l1i_1p8: ldo1 {
+			regulator-name = "vreg_l1i_1p8";
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+			regulator-always-on;
+		};
+
+		vreg_l2i_1p2: ldo2 {
+			regulator-name = "vreg_l2i_1p2";
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3i_0p8: ldo3 {
+			regulator-name = "vreg_l3i_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s1i_0p9: smps1 {
+			regulator-name = "vreg_s1i_0p9";
+			regulator-min-microvolt = <900000>;
+			regulator-max-microvolt = <920000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_s2i_1p0: smps2 {
+			regulator-name = "vreg_s2i_1p0";
+			regulator-min-microvolt = <1000000>;
+			regulator-max-microvolt = <1100000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+
+	regulators-7 {
+		compatible = "qcom,pm8550ve-rpmh-regulators";
+		qcom,pmic-id = "j";
+
+		vdd-l1-supply = <&vreg_s1f_0p7>;
+		vdd-l2-supply = <&vreg_s5j_1p2>;
+		vdd-l3-supply = <&vreg_s1f_0p7>;
+		vdd-s5-supply = <&vph_pwr>;
+
+		vreg_s5j_1p2: smps5 {
+			regulator-name = "vreg_s5j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1304000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l1j_0p8: ldo1 {
+			regulator-name = "vreg_l1j_0p8";
+			regulator-min-microvolt = <912000>;
+			regulator-max-microvolt = <912000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l2j_1p2: ldo2 {
+			regulator-name = "vreg_l2j_1p2";
+			regulator-min-microvolt = <1256000>;
+			regulator-max-microvolt = <1256000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+
+		vreg_l3j_0p8: ldo3 {
+			regulator-name = "vreg_l3j_0p8";
+			regulator-min-microvolt = <880000>;
+			regulator-max-microvolt = <880000>;
+			regulator-initial-mode = <RPMH_REGULATOR_MODE_HPM>;
+		};
+	};
+};
+
+&gpu {
+	status = "okay";
+
+	zap-shader {
+		firmware-name = "qcom/x1e80100/LENOVO/21NH/qcdxkmsucpurwa.mbn";
+	};
+};
+
+&i2c2 {
+	clock-frequency = <400000>;
+
+	pinctrl-0 = <&qup_i2c2_data_clk>, <&tpad_default>, <&kybd_default>;
+	pinctrl-names = "default";
+	status = "okay";
+
+	/* ELAN06FA */
+	touchpad@15 {
+		compatible = "hid-over-i2c";
+		reg = <0x15>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* CIRQ1080 or SYNA2BA6 */
+	touchpad@2c {
+		compatible = "hid-over-i2c";
+		reg = <0x2c>;
+
+		hid-descr-addr = <0x20>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* FTCS0038 */
+	touchpad@38 {
+		compatible = "hid-over-i2c";
+		reg = <0x38>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	keyboard@3a {
+		compatible = "hid-over-i2c";
+		reg = <0x3a>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 67 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+
+	/* GXTP5100 */
+	touchpad@5d {
+		compatible = "hid-over-i2c";
+		reg = <0x5d>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 3 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l12b_1p2>;
+
+		wakeup-source;
+	};
+};
+
+&i2c5 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	eusb5_repeater: redriver@43 {
+		compatible = "nxp,ptn3222";
+		reg = <0x43>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+	};
+
+	eusb3_repeater: redriver@47 {
+		compatible = "nxp,ptn3222";
+		reg = <0x47>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 6 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb3_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb9_repeater: redriver@4b {
+		compatible = "nxp,ptn3222";
+		reg = <0x4b>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 7 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb9_reset_n>;
+		pinctrl-names = "default";
+	};
+
+	eusb6_repeater: redriver@4f {
+		compatible = "nxp,ptn3222";
+		reg = <0x4f>;
+		#phy-cells = <0>;
+
+		vdd3v3-supply = <&vreg_l13b_3p0>;
+		vdd1v8-supply = <&vreg_l4b_1p8>;
+
+		reset-gpios = <&tlmm 184 GPIO_ACTIVE_LOW>;
+
+		pinctrl-0 = <&eusb6_reset_n>;
+		pinctrl-names = "default";
+	};
+};
+
+&i2c8 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	/* ILIT2911 or GTCH1563 */
+	touchscreen@10 {
+		compatible = "hid-over-i2c";
+		reg = <0x10>;
+
+		hid-descr-addr = <0x1>;
+		interrupts-extended = <&tlmm 51 IRQ_TYPE_LEVEL_LOW>;
+
+		vdd-supply = <&vreg_misc_3p3>;
+		vddl-supply = <&vreg_l15b_1p8>;
+
+		pinctrl-0 = <&ts0_default>;
+		pinctrl-names = "default";
+	};
+};
+
+&lpass_tlmm {
+	spkr_01_sd_n_active: spkr-01-sd-n-active-state {
+		pins = "gpio12";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+};
+
+&lpass_vamacro {
+	pinctrl-0 = <&dmic01_default>, <&dmic23_default>;
+	pinctrl-names = "default";
+
+	vdd-micb-supply = <&vreg_l1b_1p8>;
+	qcom,dmic-sample-rate = <4800000>;
+};
+
+&mdss {
+	status = "okay";
+};
+
+&mdss_dp0 {
+	status = "okay";
+};
+
+&mdss_dp0_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp1 {
+	status = "okay";
+};
+
+&mdss_dp1_out {
+	data-lanes = <0 1>;
+	link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+};
+
+&mdss_dp3 {
+	/delete-property/ #sound-dai-cells;
+
+	status = "okay";
+
+	aux-bus {
+		panel {
+			compatible = "edp-panel";
+
+			backlight = <&backlight>;
+
+			enable-gpios = <&pmc8380_3_gpios 4 GPIO_ACTIVE_HIGH>;
+			pinctrl-0 = <&edp_bl_en>;
+			pinctrl-names = "default";
+
+			power-supply = <&vreg_edp_3p3>;
+
+			port {
+				edp_panel_in: endpoint {
+					remote-endpoint = <&mdss_dp3_out>;
+				};
+			};
+		};
+	};
+
+	ports {
+		port@1 {
+			reg = <1>;
+
+			mdss_dp3_out: endpoint {
+				data-lanes = <0 1 2 3>;
+				link-frequencies = /bits/ 64 <1620000000 2700000000 5400000000 8100000000>;
+
+				remote-endpoint = <&edp_panel_in>;
+			};
+		};
+	};
+};
+
+&mdss_dp3_phy {
+	vdda-phy-supply = <&vreg_l3j_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pcie4 {
+	perst-gpios = <&tlmm 146 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 148 GPIO_ACTIVE_LOW>;
+
+	pinctrl-0 = <&pcie4_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie4_phy {
+	vdda-phy-supply = <&vreg_l3i_0p8>;
+	vdda-pll-supply = <&vreg_l3e_1p2>;
+
+	status = "okay";
+};
+
+&pcie4_port0 {
+	wifi@0 {
+		compatible = "pci17cb,1107";
+		reg = <0x10000 0x0 0x0 0x0 0x0>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+		vddpcie0p9-supply = <&vreg_pmu_pcie_0p9>;
+		vddpcie1p8-supply = <&vreg_pmu_pcie_1p8>;
+	};
+};
+
+&pcie6a {
+	perst-gpios = <&tlmm 152 GPIO_ACTIVE_LOW>;
+	wake-gpios = <&tlmm 154 GPIO_ACTIVE_LOW>;
+
+	vddpe-3v3-supply = <&vreg_nvme>;
+
+	pinctrl-0 = <&pcie6a_default>;
+	pinctrl-names = "default";
+
+	status = "okay";
+};
+
+&pcie6a_phy {
+	vdda-phy-supply = <&vreg_l1d_0p8>;
+	vdda-pll-supply = <&vreg_l2j_1p2>;
+
+	status = "okay";
+};
+
+&pm8550_pwm {
+	status = "okay";
+};
+
+&pm8550ve_8_gpios {
+	misc_3p3_reg_en: misc-3p3-reg-en-state {
+		pins = "gpio6";
+		function = "normal";
+		bias-disable;
+		input-disable;
+		output-enable;
+		drive-push-pull;
+		power-source = <1>; /* 1.8 V */
+		qcom,drive-strength = <PMIC_GPIO_STRENGTH_LOW>;
+	};
+};
+
+&pmc8380_3_gpios {
+	edp_bl_en: edp-bl-en-state {
+		pins = "gpio4";
+		function = "normal";
+		power-source = <1>; /* 1.8V */
+		input-disable;
+		output-enable;
+	};
+
+	edp_bl_reg_en: edp-bl-reg-en-state {
+		pins = "gpio10";
+		function = "normal";
+	};
+};
+
+&qupv3_0 {
+	status = "okay";
+};
+
+&qupv3_1 {
+	status = "okay";
+};
+
+&qupv3_2 {
+	status = "okay";
+};
+
+&remoteproc_adsp {
+	firmware-name = "qcom/x1e80100/LENOVO/21NH/qcadsp8380.mbn",
+			"qcom/x1e80100/LENOVO/21NH/adsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&remoteproc_cdsp {
+	firmware-name = "qcom/x1e80100/LENOVO/21NH/qccdsp8380.mbn",
+			"qcom/x1e80100/LENOVO/21NH/cdsp_dtbs.elf";
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	cd-gpios = <&tlmm 71 GPIO_ACTIVE_LOW>;
+	pinctrl-0 = <&sdc2_default &sdc2_card_det_n>;
+	pinctrl-1 = <&sdc2_sleep &sdc2_card_det_n>;
+	pinctrl-names = "default", "sleep";
+	vmmc-supply = <&vreg_l9b_2p9>;
+	vqmmc-supply = <&vreg_l6b_1p8>;
+	status = "okay";
+};
+
+&smb2360_0 {
+	status = "okay";
+};
+
+&smb2360_0_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l2b_3p0>;
+};
+
+&smb2360_1 {
+	status = "okay";
+};
+
+&smb2360_1_eusb2_repeater {
+	vdd18-supply = <&vreg_l3d_1p8>;
+	vdd3-supply = <&vreg_l14b_3p0>;
+};
+
+&swr0 {
+	status = "okay";
+
+	pinctrl-0 = <&wsa_swr_active>, <&spkr_01_sd_n_active>;
+	pinctrl-names = "default";
+
+	/* WSA8845, Left Speaker */
+	left_spkr: speaker@0,0 {
+		compatible = "sdw20217020400";
+		reg = <0 0>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrLeft";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <1 2 3 7 10 13>;
+	};
+
+	/* WSA8845, Right Speaker */
+	right_spkr: speaker@0,1 {
+		compatible = "sdw20217020400";
+		reg = <0 1>;
+		reset-gpios = <&lpass_tlmm 12 GPIO_ACTIVE_LOW>;
+		#sound-dai-cells = <0>;
+		sound-name-prefix = "SpkrRight";
+		vdd-1p8-supply = <&vreg_l15b_1p8>;
+		vdd-io-supply = <&vreg_l12b_1p2>;
+		qcom,port-mapping = <4 5 6 7 11 13>;
+	};
+};
+
+&swr1 {
+	status = "okay";
+
+	/* WCD9385 RX */
+	wcd_rx: codec@0,4 {
+		compatible = "sdw20217010d00";
+		reg = <0 4>;
+		qcom,rx-port-mapping = <1 2 3 4 5>;
+	};
+};
+
+&swr2 {
+	status = "okay";
+
+	/* WCD9385 TX */
+	wcd_tx: codec@0,3 {
+		compatible = "sdw20217010d00";
+		reg = <0 3>;
+		qcom,tx-port-mapping = <2 2 3 4>;
+	};
+};
+
+&tlmm {
+	gpio-reserved-ranges = <34 2>, /* Unused */
+		<72 2>, /* Secure EC I2C connection (?) */
+		<238 1>; /* UFS Reset */
+
+	cam_reg_en: cam-reg-en-state {
+		pins = "gpio44";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	eusb3_reset_n: eusb3-reset-n-state {
+		pins = "gpio6";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb6_reset_n: eusb6-reset-n-state {
+		pins = "gpio184";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	eusb9_reset_n: eusb9-reset-n-state {
+		pins = "gpio7";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+		output-low;
+	};
+
+	edp_reg_en: edp-reg-en-state {
+		pins = "gpio70";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	hall_int_n_default: hall-int-n-state {
+		pins = "gpio92";
+		function = "gpio";
+		bias-disable;
+	};
+
+	kybd_default: kybd-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		bias-disable;
+	};
+
+	nvme_reg_en: nvme-reg-en-state {
+		pins = "gpio18";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	pcie4_default: pcie4-default-state {
+		clkreq-n-pins {
+			pins = "gpio147";
+			function = "pcie4_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio146";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio148";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	pcie6a_default: pcie6a-default-state {
+		clkreq-n-pins {
+			pins = "gpio153";
+			function = "pcie6a_clk";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+
+		perst-n-pins {
+			pins = "gpio152";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-disable;
+		};
+
+		wake-n-pins {
+			pins = "gpio154";
+			function = "gpio";
+			drive-strength = <2>;
+			bias-pull-up;
+		};
+	};
+
+	sdc2_card_det_n: sdc2-card-det-state {
+		pins = "gpio71";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-pull-up;
+	};
+
+	tpad_default: tpad-default-state {
+		pins = "gpio3";
+		function = "gpio";
+		bias-pull-up;
+	};
+
+	ts0_default: ts0-default-state {
+		int-n-pins {
+			pins = "gpio51";
+			function = "gpio";
+			bias-disable;
+		};
+
+		reset-n-pins {
+			pins = "gpio48";
+			function = "gpio";
+			output-high;
+			drive-strength = <16>;
+		};
+	};
+
+	usb_1_ss0_sbu_default: usb-1-ss0-sbu-state {
+		mode-pins {
+			pins = "gpio166";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+			output-high;
+		};
+
+		oe-n-pins {
+			pins = "gpio168";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio167";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+	};
+
+	usb_1_ss1_sbu_default: usb-1-ss1-sbu-state {
+		mode-pins {
+			pins = "gpio177";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+			output-high;
+		};
+
+		oe-n-pins {
+			pins = "gpio179";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+
+		sel-pins {
+			pins = "gpio178";
+			function = "gpio";
+			bias-disable;
+			drive-strength = <2>;
+		};
+	};
+
+	wcd_default: wcd-reset-n-active-state {
+		pins = "gpio191";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+		output-low;
+	};
+
+	wcn_bt_en: wcn-bt-en-state {
+		pins = "gpio116";
+		function = "gpio";
+		drive-strength = <16>;
+		output-low;
+		bias-pull-down;
+	};
+
+	wcn_sw_en: wcn-sw-en-state {
+		pins = "gpio214";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+
+	wcn_wlan_en: wcn-wlan-en-state {
+		pins = "gpio117";
+		function = "gpio";
+		drive-strength = <16>;
+		bias-disable;
+	};
+};
+
+&uart14 {
+	status = "okay";
+
+	bluetooth {
+		compatible = "qcom,wcn7850-bt";
+		max-speed = <3200000>;
+
+		vddaon-supply = <&vreg_pmu_aon_0p59>;
+		vddwlcx-supply = <&vreg_pmu_wlcx_0p8>;
+		vddwlmx-supply = <&vreg_pmu_wlmx_0p85>;
+		vddrfacmn-supply = <&vreg_pmu_rfa_cmn>;
+		vddrfa0p8-supply = <&vreg_pmu_rfa_0p8>;
+		vddrfa1p2-supply = <&vreg_pmu_rfa_1p2>;
+		vddrfa1p8-supply = <&vreg_pmu_rfa_1p8>;
+	};
+};
+
+&usb_1_ss0_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_0_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss0_qmpphy {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l1j_0p8>;
+
+	status = "okay";
+};
+
+&usb_1_ss0 {
+	status = "okay";
+};
+
+&usb_1_ss0_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss0_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss0_hs_in>;
+};
+
+&usb_1_ss0_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss0_ss_in>;
+};
+
+&usb_1_ss1_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&smb2360_1_eusb2_repeater>;
+
+	status = "okay";
+};
+
+&usb_1_ss1_qmpphy {
+	vdda-phy-supply = <&vreg_l2j_1p2>;
+	vdda-pll-supply = <&vreg_l2d_0p9>;
+
+	status = "okay";
+};
+
+&usb_1_ss1 {
+	status = "okay";
+};
+
+&usb_1_ss1_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_1_ss1_dwc3_hs {
+	remote-endpoint = <&pmic_glink_ss1_hs_in>;
+};
+
+&usb_1_ss1_qmpphy_out {
+	remote-endpoint = <&pmic_glink_ss1_ss_in>;
+};
+
+&usb_1_ss2 {
+	status = "okay";
+};
+
+&usb_1_ss2_dwc3 {
+	dr_mode = "host";
+	maximum-speed = "high-speed";
+	phys = <&usb_1_ss2_hsphy>;
+	phy-names = "usb2-phy";
+};
+
+&usb_1_ss2_hsphy {
+	vdd-supply = <&vreg_l3j_0p8>;
+	vdda12-supply = <&vreg_l2j_1p2>;
+
+	phys = <&eusb5_repeater>;
+
+	status = "okay";
+};
+
+&usb_2 {
+	status = "okay";
+};
+
+&usb_2_dwc3 {
+	dr_mode = "host";
+};
+
+&usb_2_hsphy {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb9_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp {
+	status = "okay";
+};
+
+&usb_mp_hsphy0 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb6_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy0 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};
+
+&usb_mp_hsphy1 {
+	vdd-supply = <&vreg_l2e_0p8>;
+	vdda12-supply = <&vreg_l3e_1p2>;
+
+	phys = <&eusb3_repeater>;
+
+	status = "okay";
+};
+
+&usb_mp_qmpphy1 {
+	vdda-phy-supply = <&vreg_l3e_1p2>;
+	vdda-pll-supply = <&vreg_l3c_0p8>;
+
+	status = "okay";
+};

-- 
2.48.1

Re: [PATCH v3 5/6] arm64: dts: qcom: x1p42100: Add Lenovo ThinkBook 16 G7 QOY

[Dmitry Baryshkov]

On Sat, May 24, 2025 at 11:19:12AM +0200, Jens Glathe via B4 Relay wrote:
> From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> 
> The Thinkbook 16 appears to be an X1 / X1 Plus only design.
> Add make targets for normal and -el2 variant.
> 
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> ---
>  arch/arm64/boot/dts/qcom/Makefile | 3 +++
>  1 file changed, 3 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/Makefile b/arch/arm64/boot/dts/qcom/Makefile
> index 669b888b27a1daa93ac15f47e8b9a302bb0922c2..aff4fe3e81ec0d6f6d52e2aa0da327b7576632d8 100644
> --- a/arch/arm64/boot/dts/qcom/Makefile
> +++ b/arch/arm64/boot/dts/qcom/Makefile
> @@ -327,3 +327,6 @@ x1e80100-qcp-el2-dtbs	:= x1e80100-qcp.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1e80100-qcp.dtb x1e80100-qcp-el2.dtb
>  x1p42100-crd-el2-dtbs	:= x1p42100-crd.dtb x1-el2.dtbo
>  dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-crd.dtb x1p42100-crd-el2.dtb
> +x1p42100-lenovo-thinkbook-16-el2-dtbs	:= x1p42100-lenovo-thinkbook-16.dtb x1-el2.dtbo
> +dtb-$(CONFIG_ARCH_QCOM)	+= x1p42100-lenovo-thinkbook-16.dtb x1p42100-lenovo-thinkbook-16-el2.dtb
> +

This will break without the next patch. They need to be squashet into a
single patch.

-- 
With best wishes
Dmitry

Re: [PATCH v3 4/6] firmware: qcom: scm: Allow QSEECOM on Lenovo Thinkbook 16

[Dmitry Baryshkov]

On Sat, May 24, 2025 at 11:19:11AM +0200, Jens Glathe via B4 Relay wrote:
> From: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> 
> Allow particular machine accessing eg. efivars.
> 
> Signed-off-by: Jens Glathe <jens.glathe@oldschoolsolutions.biz>
> ---
>  drivers/firmware/qcom/qcom_scm.c | 1 +
>  1 file changed, 1 insertion(+)
> 

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>

-- 
With best wishes
Dmitry

Re: [PATCH v3 5/6] arm64: dts: qcom: x1p42100: Add Lenovo ThinkBook 16 G7 QOY

[Jens Glathe]

Am 24.05.25 um 12:11 schrieb Dmitry Baryshkov:
> This will break without the next patch. They need to be squashet into a
> single patch.
>
Changing the order wouldn't suffice? No problem, will squash

with best regards

Jens

Re: [PATCH v3 5/6] arm64: dts: qcom: x1p42100: Add Lenovo ThinkBook 16 G7 QOY

[Konrad Dybcio]

On 5/24/25 12:36 PM, Jens Glathe wrote:
> Am 24.05.25 um 12:11 schrieb Dmitry Baryshkov:
>> This will break without the next patch. They need to be squashet into a
>> single patch.
>>
> Changing the order wouldn't suffice?

It would, but that would then mean you're introducing dead (i.e. not
compiled) code in one of the patches

Konrad