[PATCH v6 0/5] Add driver for EC found on Qualcomm reference devices

[PATCH v6 0/5] Add driver for EC found on Qualcomm reference devices

[Anvesh Jain P]

From: Anvesh Jain P <anvesh.p@oss.qualcomm.com>

Add Embedded controller driver support for Hamoa/Purwa/Glymur Qualcomm
reference boards. It handles fan control, temperature sensors, access
to EC state changes and supports reporting suspend entry/exit to the EC.

---
Changes in v6:
  - Add missing includes: <linux/bits.h>, <linux/device.h>
    and <linux/err.h>.
  - Change the thermistor_mask format specifier from %d to %x.
  - Change loop counter to unsigned int.
  - Replace snprintf() with scnprintf() for safer string handling.
  - Use sizeof(name) instead of the EC_FAN_NAME_SIZE macro directly.
  - Add missing braces.
  - Link to v5: https://lore.kernel.org/r/20260317-add-driver-for-ec-v5-0-38d11f524856@oss.qualcomm.com

Changes in v5:
  - Fix subject line and commit description, drop redundant
    "bindings for".
  - Rename binding file: qcom,hamoa-ec.yaml → qcom,hamoa-crd-ec.yaml
    to match the compatible string.
  - Update $id URI to match the new filename.
  - Add <linux/interrupt.h> and <linux/slab.h> includes.
  - Switch to devm_thermal_of_cooling_device_register, remove manual
    unroll loop.
  - Ratelimit all IRQ handler log messages.
  - Promote unknown EC event log from dev_dbg to dev_notice.
  - Remove redundant error message after devm_request_threaded_irq.
  - Simplify qcom_ec_sci_evt_control, resume, and suspend using direct
    returns.
  - Add dev_warn + early return for zero fan count; driver stays loaded
    for PM notifications.
  - Fix thermistor presence bitmask documentation: 1 = present, 0 = absent.
  - Fix snprintf format specifier to %u to suppress -Wformat-truncation.
  - Remove unused cdev variable from qcom_ec_probe.
  - Fix typo: "exluding" → "excluding" in register map comments.
  - Fix capitalization: "ec" → "EC" in error messages.
  - Link to v4: https://lore.kernel.org/r/20260313-v04-add-driver-for-ec-v4-0-ca9d0efd62aa@oss.qualcomm.com

Changes in v4:
  - Fix fan count calculation to use min() instead of max() to correctly
    cap fan_cnt at EC_MAX_FAN_CNT.
  - Remove unnecessary mutex lock/unlock.
  - Disable fan debug mode on ec module removal.
  - Fix issue reported by kernel test robot.
  - Consolidate hamoa-iot-evk specific changes into hamoa-iot-evk.dts.
  - Add board-specific compatible strings as per review comments.
  - Link to v3: https://lore.kernel.org/all/20260308233646.2318676-1-sibi.sankar@oss.qualcomm.com/

Changes in v3:
  - Revamp the bindings and driver to support generic ec specification
    that works across Qualcomm Hamoa/Purwa and Glymur reference devices.
  - Add ec nodes to Hamoa/Purwa CRDs and IOT-EVKs.
  - Add ec node to Glymur CRDs.
  - Link to v2: https://lore.kernel.org/lkml/20241219200821.8328-1-maccraft123mc@gmail.com/
  - Link to v1: https://lore.kernel.org/lkml/20240927185345.3680-1-maccraft123mc@gmail.com/

---
Maya Matuszczyk (1):
      dt-bindings: embedded-controller: Add Qualcomm reference device EC description

Sibi Sankar (4):
      platform: arm64: Add driver for EC found on Qualcomm reference devices
      arm64: dts: qcom: glymur-crd: Add Embedded controller node
      arm64: dts: qcom: x1-crd: Add Embedded controller node
      arm64: dts: qcom: hamoa-iot-evk: Add Embedded controller node

 .../embedded-controller/qcom,hamoa-crd-ec.yaml     |  56 +++
 MAINTAINERS                                        |   8 +
 arch/arm64/boot/dts/qcom/glymur-crd.dts            |  22 +
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts         |  16 +
 arch/arm64/boot/dts/qcom/x1-crd.dtsi               |  16 +
 drivers/platform/arm64/Kconfig                     |  12 +
 drivers/platform/arm64/Makefile                    |   1 +
 drivers/platform/arm64/qcom-hamoa-ec.c             | 451 +++++++++++++++++++++
 8 files changed, 582 insertions(+)
---
base-commit: 85964cdcad0fac9a0eb7b87a0f9d88cc074b854c
change-id: 20260309-add-driver-for-ec-3fa478f264d9

Best regards,
-- 
Anvesh Jain P <anvesh.p@oss.qualcomm.com>

[PATCH v6 1/5] dt-bindings: embedded-controller: Add Qualcomm reference device EC description

[Anvesh Jain P]

From: Maya Matuszczyk <maccraft123mc@gmail.com>

Add description for the EC firmware running on Hamoa/Purwa and Glymur
reference devices.

Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Co-developed-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@oss.qualcomm.com>
Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
---
 .../embedded-controller/qcom,hamoa-crd-ec.yaml     | 56 ++++++++++++++++++++++
 1 file changed, 56 insertions(+)

diff --git a/Documentation/devicetree/bindings/embedded-controller/qcom,hamoa-crd-ec.yaml b/Documentation/devicetree/bindings/embedded-controller/qcom,hamoa-crd-ec.yaml
new file mode 100644
index 000000000000..ac5a08f8f76d
--- /dev/null
+++ b/Documentation/devicetree/bindings/embedded-controller/qcom,hamoa-crd-ec.yaml
@@ -0,0 +1,56 @@
+# SPDX-License-Identifier: (GPL-2.0-only OR BSD-2-Clause)
+%YAML 1.2
+---
+$id: http://devicetree.org/schemas/embedded-controller/qcom,hamoa-crd-ec.yaml#
+$schema: http://devicetree.org/meta-schemas/core.yaml#
+
+title: Qualcomm Hamoa Embedded Controller
+
+maintainers:
+  - Sibi Sankar <sibi.sankar@oss.qualcomm.com>
+  - Anvesh Jain P <anvesh.p@oss.qualcomm.com>
+
+description:
+  Qualcomm Snapdragon based Hamoa/Purwa and Glymur reference devices have an
+  EC running on different MCU chips. The EC handles things like fan control,
+  temperature sensors, access to EC internal state changes.
+
+properties:
+  compatible:
+    oneOf:
+      - items:
+          - enum:
+              - qcom,glymur-crd-ec
+              - qcom,hamoa-iot-evk-ec
+          - const: qcom,hamoa-crd-ec
+      - enum:
+          - qcom,hamoa-crd-ec
+
+  reg:
+    const: 0x76
+
+  interrupts:
+    maxItems: 1
+
+required:
+  - compatible
+  - reg
+  - interrupts
+
+additionalProperties: false
+
+examples:
+  - |
+    #include <dt-bindings/interrupt-controller/irq.h>
+    i2c {
+        #address-cells = <1>;
+        #size-cells = <0>;
+
+        embedded-controller@76 {
+            compatible = "qcom,hamoa-crd-ec";
+            reg = <0x76>;
+
+            interrupts-extended = <&tlmm 66 IRQ_TYPE_LEVEL_HIGH>;
+        };
+    };
+...

-- 
2.34.1

[PATCH v6 2/5] platform: arm64: Add driver for EC found on Qualcomm reference devices

[Anvesh Jain P]

From: Sibi Sankar <sibi.sankar@oss.qualcomm.com>

Add Embedded controller driver support for Hamoa/Purwa/Glymur qualcomm
reference boards. It handles fan control, temperature sensors, access
to EC state changes and supports reporting suspend entry/exit to the
EC.

Co-developed-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Signed-off-by: Maya Matuszczyk <maccraft123mc@gmail.com>
Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Acked-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
---
 MAINTAINERS                            |   8 +
 drivers/platform/arm64/Kconfig         |  12 +
 drivers/platform/arm64/Makefile        |   1 +
 drivers/platform/arm64/qcom-hamoa-ec.c | 451 +++++++++++++++++++++++++++++++++
 4 files changed, 472 insertions(+)

diff --git a/MAINTAINERS b/MAINTAINERS
index 30ca84404976..bcd7b0729ab7 100644
--- a/MAINTAINERS
+++ b/MAINTAINERS
@@ -22001,6 +22001,14 @@ S:	Supported
 W:	https://wireless.wiki.kernel.org/en/users/Drivers/wcn36xx
 F:	drivers/net/wireless/ath/wcn36xx/
 
+QUALCOMM HAMOA EMBEDDED CONTROLLER DRIVER
+M:	Sibi Sankar <sibi.sankar@oss.qualcomm.com>
+M:	Anvesh Jain P <anvesh.p@oss.qualcomm.com>
+L:	linux-arm-msm@vger.kernel.org
+S:	Maintained
+F:	Documentation/devicetree/bindings/embedded-controller/qcom,hamoa-ec.yaml
+F:	drivers/platform/arm64/qcom-hamoa-ec.c
+
 QUANTENNA QTNFMAC WIRELESS DRIVER
 M:	Igor Mitsyanko <imitsyanko@quantenna.com>
 R:	Sergey Matyukevich <geomatsi@gmail.com>
diff --git a/drivers/platform/arm64/Kconfig b/drivers/platform/arm64/Kconfig
index 10f905d7d6bf..025cdf091f9e 100644
--- a/drivers/platform/arm64/Kconfig
+++ b/drivers/platform/arm64/Kconfig
@@ -90,4 +90,16 @@ config EC_LENOVO_THINKPAD_T14S
 
 	  Say M or Y here to include this support.
 
+config EC_QCOM_HAMOA
+	tristate "Embedded Controller driver for Qualcomm Hamoa/Glymur reference devices"
+	depends on ARCH_QCOM || COMPILE_TEST
+	depends on I2C
+	help
+	  Say M or Y here to enable the Embedded Controller driver for Qualcomm
+	  Snapdragon-based Hamoa/Glymur reference devices. The driver handles fan
+	  control, temperature sensors, access to EC state changes and supports
+	  reporting suspend entry/exit to the EC.
+
+	  This driver currently supports Hamoa/Purwa/Glymur reference devices.
+
 endif # ARM64_PLATFORM_DEVICES
diff --git a/drivers/platform/arm64/Makefile b/drivers/platform/arm64/Makefile
index 60c131cff6a1..7681be4a46e9 100644
--- a/drivers/platform/arm64/Makefile
+++ b/drivers/platform/arm64/Makefile
@@ -9,3 +9,4 @@ obj-$(CONFIG_EC_ACER_ASPIRE1)	+= acer-aspire1-ec.o
 obj-$(CONFIG_EC_HUAWEI_GAOKUN)	+= huawei-gaokun-ec.o
 obj-$(CONFIG_EC_LENOVO_YOGA_C630) += lenovo-yoga-c630.o
 obj-$(CONFIG_EC_LENOVO_THINKPAD_T14S) += lenovo-thinkpad-t14s.o
+obj-$(CONFIG_EC_QCOM_HAMOA) += qcom-hamoa-ec.o
diff --git a/drivers/platform/arm64/qcom-hamoa-ec.c b/drivers/platform/arm64/qcom-hamoa-ec.c
new file mode 100644
index 000000000000..0f883130ac9a
--- /dev/null
+++ b/drivers/platform/arm64/qcom-hamoa-ec.c
@@ -0,0 +1,451 @@
+// SPDX-License-Identifier: GPL-2.0-only
+/*
+ * Copyright (c) 2024 Maya Matuszczyk <maccraft123mc@gmail.com>
+ * Copyright (c) Qualcomm Technologies, Inc. and/or its subsidiaries.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bits.h>
+#include <linux/device.h>
+#include <linux/err.h>
+#include <linux/i2c.h>
+#include <linux/interrupt.h>
+#include <linux/kernel.h>
+#include <linux/module.h>
+#include <linux/pm.h>
+#include <linux/slab.h>
+#include <linux/thermal.h>
+
+#define EC_SCI_EVT_READ_CMD	0x05
+#define EC_FW_VERSION_CMD	0x0e
+#define EC_MODERN_STANDBY_CMD	0x23
+#define EC_FAN_DBG_CONTROL_CMD	0x30
+#define EC_SCI_EVT_CONTROL_CMD	0x35
+#define EC_THERMAL_CAP_CMD	0x42
+
+#define EC_FW_VERSION_RESP_LEN	4
+#define EC_THERMAL_CAP_RESP_LEN	3
+#define EC_FAN_DEBUG_CMD_LEN	6
+#define EC_FAN_SPEED_DATA_SIZE	4
+
+#define EC_MODERN_STANDBY_ENTER	0x01
+#define EC_MODERN_STANDBY_EXIT	0x00
+
+#define EC_FAN_DEBUG_MODE_OFF   0
+#define EC_FAN_DEBUG_MODE_ON    BIT(0)
+#define EC_FAN_ON               BIT(1)
+#define EC_FAN_DEBUG_TYPE_PWM   BIT(2)
+#define EC_MAX_FAN_CNT		2
+#define EC_FAN_NAME_SIZE	20
+#define EC_FAN_MAX_PWM		255
+
+enum qcom_ec_sci_events {
+	EC_FAN1_STATUS_CHANGE_EVT = 0x30,
+	EC_FAN2_STATUS_CHANGE_EVT,
+	EC_FAN1_SPEED_CHANGE_EVT,
+	EC_FAN2_SPEED_CHANGE_EVT,
+	EC_NEW_LUT_SET_EVT,
+	EC_FAN_PROFILE_SWITCH_EVT,
+	EC_THERMISTOR_1_THRESHOLD_CROSS_EVT,
+	EC_THERMISTOR_2_THRESHOLD_CROSS_EVT,
+	EC_THERMISTOR_3_THRESHOLD_CROSS_EVT,
+	/* Reserved: 0x39 - 0x3c/0x3f */
+	EC_RECOVERED_FROM_RESET_EVT = 0x3d,
+};
+
+struct qcom_ec_version {
+	u8 main_version;
+	u8 sub_version;
+	u8 test_version;
+};
+
+struct qcom_ec_thermal_cap {
+#define EC_THERMAL_FAN_CNT(x)		(FIELD_GET(GENMASK(1, 0), (x)))
+#define EC_THERMAL_FAN_TYPE(x)		(FIELD_GET(GENMASK(4, 2), (x)))
+#define EC_THERMAL_THERMISTOR_MASK(x)	(FIELD_GET(GENMASK(7, 0), (x)))
+	u8 fan_cnt;
+	u8 fan_type;
+	u8 thermistor_mask;
+};
+
+struct qcom_ec_cooling_dev {
+	struct thermal_cooling_device *cdev;
+	struct device *parent_dev;
+	u8 fan_id;
+	u8 state;
+};
+
+struct qcom_ec {
+	struct qcom_ec_cooling_dev *ec_cdev;
+	struct qcom_ec_thermal_cap thermal_cap;
+	struct qcom_ec_version version;
+	struct i2c_client *client;
+};
+
+static int qcom_ec_read(struct qcom_ec *ec, u8 cmd, u8 resp_len, u8 *resp)
+{
+	int ret;
+
+	ret = i2c_smbus_read_i2c_block_data(ec->client, cmd, resp_len, resp);
+
+	if (ret < 0)
+		return ret;
+	else if (ret == 0 || ret == 0xff)
+		return -EOPNOTSUPP;
+
+	if (resp[0] >= resp_len)
+		return -EINVAL;
+
+	return 0;
+}
+
+/*
+ * EC Device Firmware Version:
+ *
+ * Read Response:
+ * ----------------------------------------------------------------------
+ * | Offset	| Name		| Description				|
+ * ----------------------------------------------------------------------
+ * | 0x00	| Byte count	| Number of bytes in response		|
+ * |		|		| (excluding byte count)		|
+ * ----------------------------------------------------------------------
+ * | 0x01	| Test-version	| Test-version of EC firmware		|
+ * ----------------------------------------------------------------------
+ * | 0x02	| Sub-version	| Sub-version of EC firmware		|
+ * ----------------------------------------------------------------------
+ * | 0x03	| Main-version	| Main-version of EC firmware		|
+ * ----------------------------------------------------------------------
+ *
+ */
+static int qcom_ec_read_fw_version(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct qcom_ec *ec = i2c_get_clientdata(client);
+	struct qcom_ec_version *version = &ec->version;
+	u8 resp[EC_FW_VERSION_RESP_LEN];
+	int ret;
+
+	ret = qcom_ec_read(ec, EC_FW_VERSION_CMD, EC_FW_VERSION_RESP_LEN, resp);
+	if (ret < 0)
+		return ret;
+
+	version->main_version = resp[3];
+	version->sub_version = resp[2];
+	version->test_version = resp[1];
+
+	dev_dbg(dev, "EC Version %d.%d.%d\n",
+		version->main_version, version->sub_version, version->test_version);
+
+	return 0;
+}
+
+/*
+ * EC Device Thermal Capabilities:
+ *
+ * Read Response:
+ * ------------------------------------------------------------------------------
+ * | Offset		| Name		| Description				|
+ * ------------------------------------------------------------------------------
+ * | 0x00		| Byte count	| Number of bytes in response		|
+ * |			|		| (excluding byte count)		|
+ * ------------------------------------------------------------------------------
+ * | 0x02 (LSB)	| EC Thermal	| Bit 0-1: Number of fans		|
+ * | 0x3		| Capabilities	| Bit 2-4: Type of fan			|
+ * |			|		| Bit 5-6: Reserved			|
+ * |			|		| Bit 7: Data Valid/Invalid		|
+ * |			|		|	 (Valid - 1, Invalid - 0)	|
+ * |			|		| Bit 8-15: Thermistor 0 - 7 presence	|
+ * |			|		|	    (1 present, 0 absent)	|
+ * ------------------------------------------------------------------------------
+ *
+ */
+static int qcom_ec_thermal_capabilities(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+	struct qcom_ec *ec = i2c_get_clientdata(client);
+	struct qcom_ec_thermal_cap *cap = &ec->thermal_cap;
+	u8 resp[EC_THERMAL_CAP_RESP_LEN];
+	int ret;
+
+	ret = qcom_ec_read(ec, EC_THERMAL_CAP_CMD, EC_THERMAL_CAP_RESP_LEN, resp);
+	if (ret < 0)
+		return ret;
+
+	cap->fan_cnt = min(EC_MAX_FAN_CNT, EC_THERMAL_FAN_CNT(resp[1]));
+	cap->fan_type = EC_THERMAL_FAN_TYPE(resp[1]);
+	cap->thermistor_mask = EC_THERMAL_THERMISTOR_MASK(resp[2]);
+
+	dev_dbg(dev, "Fan count: %d Fan Type: %d Thermistor Mask: %x\n",
+		cap->fan_cnt, cap->fan_type, cap->thermistor_mask);
+
+	return 0;
+}
+
+static irqreturn_t qcom_ec_irq(int irq, void *data)
+{
+	struct qcom_ec *ec = data;
+	struct device *dev = &ec->client->dev;
+	int val;
+
+	val = i2c_smbus_read_byte_data(ec->client, EC_SCI_EVT_READ_CMD);
+	if (val < 0) {
+		dev_err_ratelimited(dev, "Failed to read EC SCI Event: %d\n", val);
+		return IRQ_HANDLED;
+	}
+
+	switch (val) {
+	case EC_FAN1_STATUS_CHANGE_EVT:
+		dev_dbg_ratelimited(dev, "Fan1 status changed\n");
+		break;
+	case EC_FAN2_STATUS_CHANGE_EVT:
+		dev_dbg_ratelimited(dev, "Fan2 status changed\n");
+		break;
+	case EC_FAN1_SPEED_CHANGE_EVT:
+		dev_dbg_ratelimited(dev, "Fan1 speed crossed low/high trip point\n");
+		break;
+	case EC_FAN2_SPEED_CHANGE_EVT:
+		dev_dbg_ratelimited(dev, "Fan2 speed crossed low/high trip point\n");
+		break;
+	case EC_NEW_LUT_SET_EVT:
+		dev_dbg_ratelimited(dev, "New LUT set\n");
+		break;
+	case EC_FAN_PROFILE_SWITCH_EVT:
+		dev_dbg_ratelimited(dev, "FAN Profile switched\n");
+		break;
+	case EC_THERMISTOR_1_THRESHOLD_CROSS_EVT:
+		dev_dbg_ratelimited(dev, "Thermistor 1 threshold crossed\n");
+		break;
+	case EC_THERMISTOR_2_THRESHOLD_CROSS_EVT:
+		dev_dbg_ratelimited(dev, "Thermistor 2 threshold crossed\n");
+		break;
+	case EC_THERMISTOR_3_THRESHOLD_CROSS_EVT:
+		dev_dbg_ratelimited(dev, "Thermistor 3 threshold crossed\n");
+		break;
+	case EC_RECOVERED_FROM_RESET_EVT:
+		dev_dbg_ratelimited(dev, "EC recovered from reset\n");
+		break;
+	default:
+		dev_notice_ratelimited(dev, "Unknown EC event: %d\n", val);
+		break;
+	}
+
+	return IRQ_HANDLED;
+}
+
+static int qcom_ec_sci_evt_control(struct device *dev, bool enable)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_write_byte_data(client, EC_SCI_EVT_CONTROL_CMD, !!enable);
+}
+
+static int qcom_ec_fan_get_max_state(struct thermal_cooling_device *cdev, unsigned long *state)
+{
+	*state = EC_FAN_MAX_PWM;
+
+	return 0;
+}
+
+static int qcom_ec_fan_get_cur_state(struct thermal_cooling_device *cdev, unsigned long *state)
+{
+	struct qcom_ec_cooling_dev *ec_cdev = cdev->devdata;
+
+	*state = ec_cdev->state;
+
+	return 0;
+}
+
+/*
+ * Fan Debug control command:
+ *
+ * Command Payload:
+ * --------------------------------------------------------------------------------------
+ * | Offset		| Name		| Description					|
+ * --------------------------------------------------------------------------------------
+ * | 0x00		| Command	| Fan control command				|
+ * --------------------------------------------------------------------------------------
+ * | 0x01		| Fan ID	| 0x1 : Fan 1					|
+ * |			|		| 0x2 : Fan 2					|
+ * --------------------------------------------------------------------------------------
+ * | 0x02		| Byte count = 4| Size of data to set fan speed			|
+ * --------------------------------------------------------------------------------------
+ * | 0x03		| Mode		| Bit 0: Debug Mode On/Off (0 - OFF, 1 - ON )	|
+ * |			|		| Bit 1: Fan On/Off (0 - Off, 1 - ON)		|
+ * |			|		| Bit 2: Debug Type (0 - RPM, 1 - PWM)		|
+ * --------------------------------------------------------------------------------------
+ * | 0x04 (LSB)	| Speed in RPM	| RPM value, if mode selected is RPM		|
+ * | 0x05		|		|						|
+ * --------------------------------------------------------------------------------------
+ * | 0x06		| Speed in PWM	| PWM value, if mode selected is PWM (0 - 255)	|
+ * ______________________________________________________________________________________
+ *
+ */
+static int qcom_ec_fan_debug_mode_off(struct qcom_ec_cooling_dev *ec_cdev)
+{
+	struct device *dev = ec_cdev->parent_dev;
+	struct i2c_client *client = to_i2c_client(dev);
+	u8 request[6] = { ec_cdev->fan_id, EC_FAN_SPEED_DATA_SIZE,
+			  EC_FAN_DEBUG_MODE_OFF, 0, 0, 0 };
+	int ret;
+
+	ret = i2c_smbus_write_i2c_block_data(client, EC_FAN_DBG_CONTROL_CMD,
+					     sizeof(request), request);
+	if (ret) {
+		dev_err(dev, "Failed to turn off fan%d debug mode: %d\n",
+			ec_cdev->fan_id, ret);
+	}
+
+	return ret;
+}
+
+static int qcom_ec_fan_set_cur_state(struct thermal_cooling_device *cdev, unsigned long state)
+{
+	struct qcom_ec_cooling_dev *ec_cdev = cdev->devdata;
+	struct device *dev = ec_cdev->parent_dev;
+	struct i2c_client *client = to_i2c_client(dev);
+	u8 request[6] = { ec_cdev->fan_id, EC_FAN_SPEED_DATA_SIZE,
+			  EC_FAN_DEBUG_MODE_ON | EC_FAN_ON | EC_FAN_DEBUG_TYPE_PWM,
+			  0, 0, state };
+	int ret;
+
+	ret = i2c_smbus_write_i2c_block_data(client, EC_FAN_DBG_CONTROL_CMD,
+					     sizeof(request), request);
+	if (ret) {
+		dev_err(dev, "Failed to set fan pwm: %d\n", ret);
+		return ret;
+	}
+
+	ec_cdev->state = state;
+
+	return 0;
+}
+
+static const struct thermal_cooling_device_ops qcom_ec_thermal_ops = {
+	.get_max_state = qcom_ec_fan_get_max_state,
+	.get_cur_state = qcom_ec_fan_get_cur_state,
+	.set_cur_state = qcom_ec_fan_set_cur_state,
+};
+
+static int qcom_ec_resume(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_write_byte_data(client, EC_MODERN_STANDBY_CMD,
+					 EC_MODERN_STANDBY_ENTER);
+}
+
+static int qcom_ec_suspend(struct device *dev)
+{
+	struct i2c_client *client = to_i2c_client(dev);
+
+	return i2c_smbus_write_byte_data(client, EC_MODERN_STANDBY_CMD,
+					 EC_MODERN_STANDBY_EXIT);
+}
+
+static int qcom_ec_probe(struct i2c_client *client)
+{
+	struct device *dev = &client->dev;
+	struct qcom_ec *ec;
+	unsigned int i;
+	int ret;
+
+	ec = devm_kzalloc(dev, sizeof(*ec), GFP_KERNEL);
+	if (!ec)
+		return -ENOMEM;
+
+	ec->client = client;
+
+	ret = devm_request_threaded_irq(dev, client->irq, NULL, qcom_ec_irq,
+					IRQF_ONESHOT, "qcom_ec", ec);
+	if (ret < 0)
+		return ret;
+
+	i2c_set_clientdata(client, ec);
+
+	ret = qcom_ec_read_fw_version(dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to read EC firmware version\n");
+
+	ret = qcom_ec_sci_evt_control(dev, true);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to enable SCI events\n");
+
+	ret = qcom_ec_thermal_capabilities(dev);
+	if (ret < 0)
+		return dev_err_probe(dev, ret, "Failed to read thermal capabilities\n");
+
+	if (ec->thermal_cap.fan_cnt == 0) {
+		dev_warn(dev, FW_BUG "Failed to get fan count, firmware update required\n");
+		return 0;
+	}
+
+	ec->ec_cdev = devm_kcalloc(dev, ec->thermal_cap.fan_cnt, sizeof(*ec->ec_cdev), GFP_KERNEL);
+	if (!ec->ec_cdev)
+		return -ENOMEM;
+
+	for (i = 0; i < ec->thermal_cap.fan_cnt; i++) {
+		struct qcom_ec_cooling_dev *ec_cdev = &ec->ec_cdev[i];
+		char name[EC_FAN_NAME_SIZE];
+
+		scnprintf(name, sizeof(name), "qcom_ec_fan_%u", i);
+		ec_cdev->fan_id = i + 1;
+		ec_cdev->parent_dev = dev;
+
+		ec_cdev->cdev = devm_thermal_of_cooling_device_register(dev, NULL, name, ec_cdev,
+									&qcom_ec_thermal_ops);
+		if (IS_ERR(ec_cdev->cdev)) {
+			return dev_err_probe(dev, PTR_ERR(ec_cdev->cdev),
+					     "Failed to register fan%d cooling device\n", i);
+		}
+	}
+
+	return 0;
+}
+
+static void qcom_ec_remove(struct i2c_client *client)
+{
+	struct qcom_ec *ec = i2c_get_clientdata(client);
+	struct device *dev = &client->dev;
+	int ret;
+
+	ret = qcom_ec_sci_evt_control(dev, false);
+	if (ret < 0)
+		dev_err(dev, "Failed to disable SCI events: %d\n", ret);
+
+	for (int i = 0; i < ec->thermal_cap.fan_cnt; i++) {
+		struct qcom_ec_cooling_dev *ec_cdev = &ec->ec_cdev[i];
+
+		qcom_ec_fan_debug_mode_off(ec_cdev);
+	}
+}
+
+static const struct of_device_id qcom_ec_of_match[] = {
+	{ .compatible = "qcom,hamoa-crd-ec" },
+	{}
+};
+MODULE_DEVICE_TABLE(of, qcom_ec_of_match);
+
+static const struct i2c_device_id qcom_ec_i2c_id_table[] = {
+	{ "qcom-hamoa-ec", },
+	{}
+};
+MODULE_DEVICE_TABLE(i2c, qcom_ec_i2c_id_table);
+
+static DEFINE_SIMPLE_DEV_PM_OPS(qcom_ec_pm_ops,
+		qcom_ec_suspend,
+		qcom_ec_resume);
+
+static struct i2c_driver qcom_ec_i2c_driver = {
+	.driver = {
+		.name = "qcom-hamoa-ec",
+		.of_match_table = qcom_ec_of_match,
+		.pm = &qcom_ec_pm_ops
+	},
+	.probe = qcom_ec_probe,
+	.remove = qcom_ec_remove,
+	.id_table = qcom_ec_i2c_id_table,
+};
+module_i2c_driver(qcom_ec_i2c_driver);
+
+MODULE_DESCRIPTION("QCOM Hamoa Embedded Controller");
+MODULE_LICENSE("GPL");

-- 
2.34.1

[PATCH v6 3/5] arm64: dts: qcom: glymur-crd: Add Embedded controller node

[Anvesh Jain P]

From: Sibi Sankar <sibi.sankar@oss.qualcomm.com>

Add embedded controller node for Glymur CRDs which adds fan control,
temperature sensors, access to EC state changes through SCI events
and suspend entry/exit notifications to the EC.

Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/glymur-crd.dts | 22 ++++++++++++++++++++++
 1 file changed, 22 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/glymur-crd.dts b/arch/arm64/boot/dts/qcom/glymur-crd.dts
index 51ea23a49b9e..1a69b428307f 100644
--- a/arch/arm64/boot/dts/qcom/glymur-crd.dts
+++ b/arch/arm64/boot/dts/qcom/glymur-crd.dts
@@ -198,6 +198,22 @@ ptn3222_1: redriver@47 {
 	};
 };
 
+&i2c9 {
+	clock-frequency = <400000>;
+
+	status = "okay";
+
+	embedded-controller@76 {
+		compatible = "qcom,glymur-crd-ec", "qcom,hamoa-crd-ec";
+		reg = <0x76>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&ec_int_n_default>;
+		pinctrl-names = "default";
+	};
+};
+
 &mdss {
 	status = "okay";
 };
@@ -263,6 +279,12 @@ &smb2370_k_e2_eusb2_repeater {
 };
 
 &tlmm {
+	ec_int_n_default: ec-int-n-state {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+	};
+
 	edp_bl_en: edp-bl-en-state {
 		pins = "gpio18";
 		function = "gpio";

-- 
2.34.1

[PATCH v6 4/5] arm64: dts: qcom: x1-crd: Add Embedded controller node

[Anvesh Jain P]

From: Sibi Sankar <sibi.sankar@oss.qualcomm.com>

Add embedded controller node for Hamoa/Purwa CRDs which adds fan control,
temperature sensors, access to EC internal state changes and suspend
entry/exit notifications to the EC.

Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Reviewed-by: Abel Vesa <abel.vesa@oss.qualcomm.com>
Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/x1-crd.dtsi | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/x1-crd.dtsi b/arch/arm64/boot/dts/qcom/x1-crd.dtsi
index 485dcd946757..1184169f49cc 100644
--- a/arch/arm64/boot/dts/qcom/x1-crd.dtsi
+++ b/arch/arm64/boot/dts/qcom/x1-crd.dtsi
@@ -1074,6 +1074,16 @@ eusb6_repeater: redriver@4f {
 
 		#phy-cells = <0>;
 	};
+
+	embedded-controller@76 {
+		compatible = "qcom,hamoa-crd-ec";
+		reg = <0x76>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&ec_int_n_default>;
+		pinctrl-names = "default";
+	};
 };
 
 &i2c7 {
@@ -1517,6 +1527,12 @@ &tlmm {
 			       <44 4>, /* SPI (TPM) */
 			       <238 1>; /* UFS Reset */
 
+	ec_int_n_default: ec-int-n-state {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+	};
+
 	edp_reg_en: edp-reg-en-state {
 		pins = "gpio70";
 		function = "gpio";

-- 
2.34.1

[PATCH v6 5/5] arm64: dts: qcom: hamoa-iot-evk: Add Embedded controller node

[Anvesh Jain P]

From: Sibi Sankar <sibi.sankar@oss.qualcomm.com>

Add embedded controller node for Hamoa IOT EVK boards which adds fan
control, temperature sensors, access to EC internal state changes and
suspend entry/exit notifications to the EC.

Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
---
 arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 16 ++++++++++++++++
 1 file changed, 16 insertions(+)

diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
index 460f27dcd6f6..a0d2ccf931ec 100644
--- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
+++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
@@ -831,6 +831,16 @@ eusb6_repeater: redriver@4f {
 		pinctrl-0 = <&eusb6_reset_n>;
 		pinctrl-names = "default";
 	};
+
+	embedded-controller@76 {
+		compatible = "qcom,hamoa-iot-evk-ec", "qcom,hamoa-crd-ec";
+		reg = <0x76>;
+
+		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&ec_int_n_default>;
+		pinctrl-names = "default";
+	};
 };
 
 &i2c7 {
@@ -1320,6 +1330,12 @@ right_tweeter: speaker@0,1 {
 };
 
 &tlmm {
+	ec_int_n_default: ec-int-n-state {
+		pins = "gpio66";
+		function = "gpio";
+		bias-disable;
+	};
+
 	edp_reg_en: edp-reg-en-state {
 		pins = "gpio70";
 		function = "gpio";

-- 
2.34.1

Re: [PATCH v6 5/5] arm64: dts: qcom: hamoa-iot-evk: Add Embedded controller node

[Gaurav Kohli]

On 3/25/2026 5:09 PM, Anvesh Jain P wrote:
> From: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
> 
> Add embedded controller node for Hamoa IOT EVK boards which adds fan
> control, temperature sensors, access to EC internal state changes and
> suspend entry/exit notifications to the EC.
> 
> Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
> Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
> Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
> ---
>   arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 16 ++++++++++++++++
>   1 file changed, 16 insertions(+)
> 
> diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> index 460f27dcd6f6..a0d2ccf931ec 100644
> --- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
> @@ -831,6 +831,16 @@ eusb6_repeater: redriver@4f {
>   		pinctrl-0 = <&eusb6_reset_n>;
>   		pinctrl-names = "default";
>   	};
> +
> +	embedded-controller@76 {
> +		compatible = "qcom,hamoa-iot-evk-ec", "qcom,hamoa-crd-ec";
> +		reg = <0x76>;
> +
> +		interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
> +
> +		pinctrl-0 = <&ec_int_n_default>;
> +		pinctrl-names = "default";
> +	};
>   };
>   
For Hamoa iot evk board, i have also tried and cooling nodes are 
reflecting fine.
Please feel free to add:
Reviewed-by: Gaurav Kohli <gaurav.kohli@oss.qualcomm.com>
Tested-by: Gaurav Kohli <gaurav.kohli@oss.qualcomm.com>

Re: [PATCH v6 2/5] platform: arm64: Add driver for EC found on Qualcomm reference devices

[Randy Dunlap]

On 3/25/26 4:39 AM, Anvesh Jain P wrote:
> diff --git a/MAINTAINERS b/MAINTAINERS
> index 30ca84404976..bcd7b0729ab7 100644
> --- a/MAINTAINERS
> +++ b/MAINTAINERS
> @@ -22001,6 +22001,14 @@ S:	Supported
>  W:	https://wireless.wiki.kernel.org/en/users/Drivers/wcn36xx
>  F:	drivers/net/wireless/ath/wcn36xx/
>  
> +QUALCOMM HAMOA EMBEDDED CONTROLLER DRIVER
> +M:	Sibi Sankar <sibi.sankar@oss.qualcomm.com>
> +M:	Anvesh Jain P <anvesh.p@oss.qualcomm.com>
> +L:	linux-arm-msm@vger.kernel.org
> +S:	Maintained
> +F:	Documentation/devicetree/bindings/embedded-controller/qcom,hamoa-ec.yaml
> +F:	drivers/platform/arm64/qcom-hamoa-ec.c
> +

Please keep the entries in the MAINTAINERS file in alphabetical order.

>  QUANTENNA QTNFMAC WIRELESS DRIVER
>  M:	Igor Mitsyanko <imitsyanko@quantenna.com>
>  R:	Sergey Matyukevich <geomatsi@gmail.com>

-- 
~Randy

Re: [PATCH v6 2/5] platform: arm64: Add driver for EC found on Qualcomm reference devices

[Anvesh Jain P]

On 3/26/2026 3:07 AM, Randy Dunlap wrote:
> 
> 
> On 3/25/26 4:39 AM, Anvesh Jain P wrote:
>> diff --git a/MAINTAINERS b/MAINTAINERS
>> index 30ca84404976..bcd7b0729ab7 100644
>> --- a/MAINTAINERS
>> +++ b/MAINTAINERS
>> @@ -22001,6 +22001,14 @@ S:	Supported
>>  W:	https://wireless.wiki.kernel.org/en/users/Drivers/wcn36xx
>>  F:	drivers/net/wireless/ath/wcn36xx/
>>  
>> +QUALCOMM HAMOA EMBEDDED CONTROLLER DRIVER
>> +M:	Sibi Sankar <sibi.sankar@oss.qualcomm.com>
>> +M:	Anvesh Jain P <anvesh.p@oss.qualcomm.com>
>> +L:	linux-arm-msm@vger.kernel.org
>> +S:	Maintained
>> +F:	Documentation/devicetree/bindings/embedded-controller/qcom,hamoa-ec.yaml
>> +F:	drivers/platform/arm64/qcom-hamoa-ec.c
>> +
> 
> Please keep the entries in the MAINTAINERS file in alphabetical order.
>

Thanks for the review!

I wondered about this a bit but saw a lot of instances where the names
weren't in ascending order. That said, will fix it in the next re-spin.

>>  QUANTENNA QTNFMAC WIRELESS DRIVER
>>  M:	Igor Mitsyanko <imitsyanko@quantenna.com>
>>  R:	Sergey Matyukevich <geomatsi@gmail.com>
> 

-- 
Best Regards,
Anvesh

Re: [PATCH v6 5/5] arm64: dts: qcom: hamoa-iot-evk: Add Embedded controller node

[Anvesh Jain P]

On 3/25/2026 5:50 PM, Gaurav Kohli wrote:
> 
> 
> On 3/25/2026 5:09 PM, Anvesh Jain P wrote:
>> From: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
>>
>> Add embedded controller node for Hamoa IOT EVK boards which adds fan
>> control, temperature sensors, access to EC internal state changes and
>> suspend entry/exit notifications to the EC.
>>
>> Signed-off-by: Sibi Sankar <sibi.sankar@oss.qualcomm.com>
>> Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@oss.qualcomm.com>
>> Reviewed-by: Konrad Dybcio <konrad.dybcio@oss.qualcomm.com>
>> Co-developed-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
>> Signed-off-by: Anvesh Jain P <anvesh.p@oss.qualcomm.com>
>> ---
>>   arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts | 16 ++++++++++++++++
>>   1 file changed, 16 insertions(+)
>>
>> diff --git a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts b/arch/arm64/
>> boot/dts/qcom/hamoa-iot-evk.dts
>> index 460f27dcd6f6..a0d2ccf931ec 100644
>> --- a/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
>> +++ b/arch/arm64/boot/dts/qcom/hamoa-iot-evk.dts
>> @@ -831,6 +831,16 @@ eusb6_repeater: redriver@4f {
>>           pinctrl-0 = <&eusb6_reset_n>;
>>           pinctrl-names = "default";
>>       };
>> +
>> +    embedded-controller@76 {
>> +        compatible = "qcom,hamoa-iot-evk-ec", "qcom,hamoa-crd-ec";
>> +        reg = <0x76>;
>> +
>> +        interrupts-extended = <&tlmm 66 IRQ_TYPE_EDGE_FALLING>;
>> +
>> +        pinctrl-0 = <&ec_int_n_default>;
>> +        pinctrl-names = "default";
>> +    };
>>   };
>>   
> For Hamoa iot evk board, i have also tried and cooling nodes are
> reflecting fine.
> Please feel free to add:
> Reviewed-by: Gaurav Kohli <gaurav.kohli@oss.qualcomm.com>
> Tested-by: Gaurav Kohli <gaurav.kohli@oss.qualcomm.com>
>

Thanks for testing. Will add the tags in next re-spin.

-- 
Best Regards,
Anvesh