From: neil.armstrong@linaro.org
To: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>,
Abhinav Kumar <quic_abhinavk@quicinc.com>,
Jessica Zhang <quic_jesszhan@quicinc.com>,
Sam Ravnborg <sam@ravnborg.org>, David Airlie <airlied@gmail.com>,
Daniel Vetter <daniel@ffwll.ch>,
Douglas Anderson <dianders@chromium.org>,
Rob Clark <robdclark@gmail.com>,
Maxime Ripard <mripard@kernel.org>,
Maarten Lankhorst <maarten.lankhorst@linux.intel.com>,
Thomas Zimmermann <tzimmermann@suse.de>,
Rob Clark <robdclark@gmail.com>
Cc: quic_parellan@quicinc.com, dri-devel@lists.freedesktop.org,
linux-kernel@vger.kernel.org
Subject: Re: [PATCH] drm/panel: Add prepare_prev_first flag to Visionox VTDR6130
Date: Fri, 18 Aug 2023 10:25:48 +0200 [thread overview]
Message-ID: <c7c5c8f0-16e6-47bd-94e8-ce924163dfd3@linaro.org> (raw)
In-Reply-To: <ff1b04c3-c852-4e28-9054-3cebb4ca5d6e@linaro.org>
Hi Dmitry,
On 17/08/2023 20:35, Dmitry Baryshkov wrote:
> On 16/08/2023 10:51, neil.armstrong@linaro.org wrote:
>> Hi Abhinav,
>>
>> On 14/08/2023 20:02, Abhinav Kumar wrote:
<snip>
>>
>> Sending HS commands will always work on any controller, it's all about LP commands.
>> The Samsung panels you listed only send HS commands so they can use prepare_prev_first
>> and work on any controllers.
>
> I think there is some misunderstanding there, supported by the description of the flag.
>
> If I remember correctly, some hosts (sunxi) can not send DCS commands after enabling video stream and switching to HS mode, see [1]. Thus, as you know, most of the drivers have all DSI panel setup commands in drm_panel_funcs::prepare() / drm_bridge_funcs::pre_enable() callbacks, not paying attention whether these commands are to be sent in LP or in HS mode.
>
> Previously DSI source drivers could power on the DSI link either in mode_set() or in pre_enable() callbacks, with mode_set() being the hack to make panel/bridge drivers to be able to send commands from their prepare() / pre_enable() callbacks.
>
> With the prev_first flags being introduced, we have established that DSI link should be enabled in DSI host's pre_enable() callback and switched to HS mode (be it command or video) in the enable() callback.
>
> So far so good.
It seems coherent, I would like first to have a state of all DSI host drivers and make this would actually work first before adding the prev_first flag to all the required panels.
>
> Unfortunately this change is not fully backwards-compatible. This requires that all DSI panels sending commands from prepare() should have the prepare_prev_first flag. In some sense, all such patches might have Fixes: 5ea6b1702781 ("drm/panel: Add prepare_prev_first flag to drm_panel").
This kind of migration should be done *before* any possible regression, not the other way round.
If all panels sending commands from prepare() should have the prepare_prev_first flag, then it should be first, check for regressions then continue.
<snip>
>>
>> I understand, but this patch doesn't qualify as a fix for 9e15123eca79 and is too late to be merged in drm-misc-next for v6.6,
>> and since 9e15123eca79 actually breaks some support it should be reverted (+ deps) since we are late in the rc cycles.
>
> If we go this way, we can never reapply these patches. There will be no guarantee that all panel drivers are completely converted. We already have a story without an observable end - DRM_BRIDGE_ATTACH_NO_CONNECTOR.
I don't understand this point, who would block re-applying the patches ?
The migration to DRM_BRIDGE_ATTACH_NO_CONNECTOR was done over multiple Linux version and went smoothly because we reverted
regressing patches and restarted when needed, I don't understand why we can't do this here aswell.
>
> I'd consider that the DSI driver is correct here and it is about the panel drivers that require fixes patches. If you care about the particular Fixes tag, I have provided one several lines above.
Unfortunately it should be done in the other way round, prepare for migration, then migrate,
I mean if it's a required migration, then it should be done and I'll support it from both bridge and panel PoV.
So, first this patch has the wrong Fixes tag, and I would like a better explanation on the commit message in any case.
Then I would like to have an ack from some drm-misc maintainers before applying it because it fixes a patch that
was sent via the msm tree thus per the drm-misc rules I cannot apply it via the drm-misc-next-fixes tree.
Neil
<snip>
next prev parent reply other threads:[~2023-08-18 8:26 UTC|newest]
Thread overview: 30+ messages / expand[flat|nested] mbox.gz Atom feed top
2023-07-25 22:56 Jessica Zhang
2023-07-31 13:00 ` Neil Armstrong
2023-08-03 17:19 ` Jessica Zhang
2023-08-10 16:26 ` Abhinav Kumar
2023-08-14 8:01 ` neil.armstrong
2023-08-14 18:02 ` Abhinav Kumar
2023-08-16 7:51 ` neil.armstrong
2023-08-17 18:35 ` Dmitry Baryshkov
2023-08-18 8:25 ` neil.armstrong [this message]
2023-08-18 10:27 ` Dmitry Baryshkov
2023-08-21 11:26 ` Dave Stevenson
2023-08-21 8:17 ` Maxime Ripard
2023-08-21 10:01 ` neil.armstrong
2023-08-21 11:36 ` Maxime Ripard
2023-08-25 18:37 ` Jessica Zhang
2023-08-28 8:49 ` neil.armstrong
2023-08-28 17:07 ` Abhinav Kumar
2023-08-29 9:22 ` neil.armstrong
2023-08-29 9:26 ` Dmitry Baryshkov
2023-08-29 16:36 ` Abhinav Kumar
2023-08-29 16:43 ` Dmitry Baryshkov
2023-08-29 17:21 ` Abhinav Kumar
2023-08-29 18:51 ` Dmitry Baryshkov
2023-08-29 19:08 ` Abhinav Kumar
2023-08-29 19:15 ` Dmitry Baryshkov
2023-08-29 19:21 ` Abhinav Kumar
2023-08-30 2:05 ` Dmitry Baryshkov
2023-08-30 3:40 ` Abhinav Kumar
2023-08-29 14:13 ` Dave Stevenson
2023-08-29 20:43 ` Abhinav Kumar
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=c7c5c8f0-16e6-47bd-94e8-ce924163dfd3@linaro.org \
--to=neil.armstrong@linaro.org \
--cc=airlied@gmail.com \
--cc=daniel@ffwll.ch \
--cc=dianders@chromium.org \
--cc=dmitry.baryshkov@linaro.org \
--cc=dri-devel@lists.freedesktop.org \
--cc=linux-kernel@vger.kernel.org \
--cc=maarten.lankhorst@linux.intel.com \
--cc=mripard@kernel.org \
--cc=quic_abhinavk@quicinc.com \
--cc=quic_jesszhan@quicinc.com \
--cc=quic_parellan@quicinc.com \
--cc=robdclark@gmail.com \
--cc=sam@ravnborg.org \
--cc=tzimmermann@suse.de \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®