* Oops on 4.15-rc[123] on shutdown/reboot
@ 2017-12-11 15:31 Chris Clayton
2017-12-11 16:29 ` Sinan Kaya
0 siblings, 1 reply; 7+ messages in thread
From: Chris Clayton @ 2017-12-11 15:31 UTC (permalink / raw)
To: LKML; +Cc: okaya, bhelgaas
[-- Attachment #1: Type: text/plain, Size: 1463 bytes --]
I've been getting an oops when shutting down my laptop (with /sbin/halt) or rebooting it (/sbin/reboot or
/usr/sbin/kexec). Unfortunately, I can't provide the backtrace because it is on the screen for only a moment before the
system shuts down/reboots.
I have however, bisected it and the outcome is:
cc27b735ad3a75574a6ab1a66ed6b09385e77e5e is the first bad commit
commit cc27b735ad3a75574a6ab1a66ed6b09385e77e5e
Author: Sinan Kaya <okaya@codeaurora.org>
Date: Wed Oct 25 15:01:02 2017 -0400
PCI/portdrv: Turn off PCIe services during shutdown
Some of the PCIe services such as AER are being left enabled during
shutdown. This might cause spurious AER errors while SOC is being powered
down.
Clean up the PCIe services gracefully during shutdown to clear these false
positives.
Signed-off-by: Sinan Kaya <okaya@codeaurora.org>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>
:040000 040000 5a827d6956c581344a0bf392e30155c337673c1d 76c6a39b53604a0a0a370383c3503f80aa7cbc1e M drivers
I'm confident that this is the correct outcome because a kernel built with the preceding commit
(6018182d3158505f11103adaee8ffb53424df986) does not oops. Nor does -rc3 with the patch reversed.
I'm more than happy to provide additional diagnostics and test proposed fixes. As a starter for ten, I've attached the
output from 'lspci -v'. If, however, you need to see the backtrace, I'll need some advice on how to capture that.
Chris
[-- Attachment #2: lspci-v.txt --]
[-- Type: text/plain, Size: 10653 bytes --]
00:00.0 Host bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller (rev 06)
Subsystem: CLEVO/KAPOK Computer Xeon E3-1200 v3/4th Gen Core Processor DRAM Controller
Flags: bus master, fast devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:01.0 PCI bridge: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller (rev 06) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 16
Bus: primary=00, secondary=01, subordinate=01, sec-latency=0
I/O behind bridge: None
Memory behind bridge: None
Prefetchable memory behind bridge: None
Capabilities: [88] Subsystem: CLEVO/KAPOK Computer Xeon E3-1200 v3/4th Gen Core Processor PCI Express x16 Controller
Capabilities: [80] Power Management version 3
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [a0] Express Root Port (Slot+), MSI 00
Kernel driver in use: pcieport
00:02.0 VGA compatible controller: Intel Corporation 4th Gen Core Processor Integrated Graphics Controller (rev 06) (prog-if 00 [VGA controller])
Subsystem: CLEVO/KAPOK Computer 4th Gen Core Processor Integrated Graphics Controller
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f7800000 (64-bit, non-prefetchable) [size=4M]
Memory at e0000000 (64-bit, prefetchable) [size=256M]
I/O ports at f000 [size=64]
[virtual] Expansion ROM at 000c0000 [disabled] [size=128K]
Capabilities: [90] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [d0] Power Management version 2
Capabilities: [a4] PCI Advanced Features
Kernel driver in use: i915
00:03.0 Audio device: Intel Corporation Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller (rev 06)
Subsystem: CLEVO/KAPOK Computer Xeon E3-1200 v3/4th Gen Core Processor HD Audio Controller
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f7f14000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:14.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB xHCI (rev 05) (prog-if 30 [XHCI])
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family USB xHCI
Flags: bus master, medium devsel, latency 0, IRQ 16
Memory at f7f00000 (64-bit, non-prefetchable) [size=64K]
Capabilities: [70] Power Management version 2
Capabilities: [80] MSI: Enable- Count=1/8 Maskable- 64bit+
Kernel driver in use: xhci_hcd
00:16.0 Communication controller: Intel Corporation 8 Series/C220 Series Chipset Family MEI Controller #1 (rev 04)
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family MEI Controller
Flags: bus master, fast devsel, latency 0, IRQ 11
Memory at f7f1e000 (64-bit, non-prefetchable) [size=16]
Capabilities: [50] Power Management version 3
Capabilities: [8c] MSI: Enable- Count=1/1 Maskable- 64bit+
00:1a.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #2 (rev 05) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family USB EHCI
Flags: bus master, medium devsel, latency 0, IRQ 16
Memory at f7f1c000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
Kernel driver in use: ehci-pci
00:1b.0 Audio device: Intel Corporation 8 Series/C220 Series Chipset High Definition Audio Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset High Definition Audio Controller
Flags: bus master, fast devsel, latency 0, IRQ 22
Memory at f7f10000 (64-bit, non-prefetchable) [size=16K]
Capabilities: [50] Power Management version 2
Capabilities: [60] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Root Complex Integrated Endpoint, MSI 00
Kernel driver in use: snd_hda_intel
Kernel modules: snd_hda_intel
00:1c.0 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #1 (rev d5) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 16
Bus: primary=00, secondary=02, subordinate=02, sec-latency=0
I/O behind bridge: None
Memory behind bridge: None
Prefetchable memory behind bridge: None
Capabilities: [40] Express Root Port (Slot-), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Kernel driver in use: pcieport
00:1c.1 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #2 (rev d5) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 17
Bus: primary=00, secondary=03, subordinate=03, sec-latency=0
I/O behind bridge: None
Memory behind bridge: f7e00000-f7efffff [size=1M]
Prefetchable memory behind bridge: None
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Kernel driver in use: pcieport
00:1c.2 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #3 (rev d5) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 18
Bus: primary=00, secondary=04, subordinate=04, sec-latency=0
I/O behind bridge: None
Memory behind bridge: f7d00000-f7dfffff [size=1M]
Prefetchable memory behind bridge: None
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Kernel driver in use: pcieport
00:1c.3 PCI bridge: Intel Corporation 8 Series/C220 Series Chipset Family PCI Express Root Port #4 (rev d5) (prog-if 00 [Normal decode])
Flags: bus master, fast devsel, latency 0, IRQ 19
Bus: primary=00, secondary=05, subordinate=05, sec-latency=0
I/O behind bridge: 0000e000-0000efff [size=4K]
Memory behind bridge: f7c00000-f7cfffff [size=1M]
Prefetchable memory behind bridge: 00000000f0000000-00000000f00fffff [size=1M]
Capabilities: [40] Express Root Port (Slot+), MSI 00
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [90] Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family PCI Express Root Port
Capabilities: [a0] Power Management version 3
Kernel driver in use: pcieport
00:1d.0 USB controller: Intel Corporation 8 Series/C220 Series Chipset Family USB EHCI #1 (rev 05) (prog-if 20 [EHCI])
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family USB EHCI
Flags: bus master, medium devsel, latency 0, IRQ 23
Memory at f7f1b000 (32-bit, non-prefetchable) [size=1K]
Capabilities: [50] Power Management version 2
Capabilities: [58] Debug port: BAR=1 offset=00a0
Capabilities: [98] PCI Advanced Features
Kernel driver in use: ehci-pci
00:1f.0 ISA bridge: Intel Corporation HM86 Express LPC Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer HM86 Express LPC Controller
Flags: bus master, medium devsel, latency 0
Capabilities: [e0] Vendor Specific Information: Len=0c <?>
00:1f.2 SATA controller: Intel Corporation 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode] (rev 05) (prog-if 01 [AHCI 1.0])
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family 6-port SATA Controller 1 [AHCI mode]
Flags: bus master, 66MHz, medium devsel, latency 0, IRQ 19
I/O ports at f0b0 [size=8]
I/O ports at f0a0 [size=4]
I/O ports at f090 [size=8]
I/O ports at f080 [size=4]
I/O ports at f060 [size=32]
Memory at f7f1a000 (32-bit, non-prefetchable) [size=2K]
Capabilities: [80] MSI: Enable- Count=1/1 Maskable- 64bit-
Capabilities: [70] Power Management version 3
Capabilities: [a8] SATA HBA v1.0
Kernel driver in use: ahci
00:1f.3 SMBus: Intel Corporation 8 Series/C220 Series Chipset Family SMBus Controller (rev 05)
Subsystem: CLEVO/KAPOK Computer 8 Series/C220 Series Chipset Family SMBus Controller
Flags: medium devsel, IRQ 18
Memory at f7f19000 (64-bit, non-prefetchable) [size=256]
I/O ports at f040 [size=32]
Kernel driver in use: i801_smbus
03:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTS5229 PCI Express Card Reader (rev 01)
Subsystem: CLEVO/KAPOK Computer RTS5229 PCI Express Card Reader
Flags: bus master, fast devsel, latency 0, IRQ 17
Memory at f7e00000 (32-bit, non-prefetchable) [size=4K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Kernel driver in use: rtsx_pci
04:00.0 Network controller: Intel Corporation Wireless 7260 (rev c3)
Subsystem: Intel Corporation Wireless-N 7260
Flags: bus master, fast devsel, latency 0, IRQ 4
Memory at f7d00000 (64-bit, non-prefetchable) [size=8K]
Capabilities: [c8] Power Management version 3
Capabilities: [d0] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [40] Express Endpoint, MSI 00
Kernel modules: iwlwifi
05:00.0 Unassigned class [ff00]: Realtek Semiconductor Co., Ltd. RTL8411 PCI Express Card Reader (rev 01)
Subsystem: CLEVO/KAPOK Computer RTL8411 PCI Express Card Reader
Flags: bus master, fast devsel, latency 0, IRQ 16
Memory at f7c00000 (32-bit, non-prefetchable) [size=64K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 00
Capabilities: [b0] MSI-X: Enable- Count=1 Masked-
Capabilities: [d0] Vital Product Data
Kernel driver in use: rtsx_pci
05:00.2 Ethernet controller: Realtek Semiconductor Co., Ltd. RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller (rev 0a)
Subsystem: CLEVO/KAPOK Computer RTL8111/8168/8411 PCI Express Gigabit Ethernet Controller
Flags: bus master, fast devsel, latency 0, IRQ 19
I/O ports at e000 [size=256]
Memory at f0004000 (64-bit, prefetchable) [size=4K]
Memory at f0000000 (64-bit, prefetchable) [size=16K]
Capabilities: [40] Power Management version 3
Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+
Capabilities: [70] Express Endpoint, MSI 01
Capabilities: [b0] MSI-X: Enable- Count=4 Masked-
Capabilities: [d0] Vital Product Data
Kernel driver in use: r8169
Kernel modules: r8169
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Oops on 4.15-rc[123] on shutdown/reboot
2017-12-11 15:31 Oops on 4.15-rc[123] on shutdown/reboot Chris Clayton
@ 2017-12-11 16:29 ` Sinan Kaya
2017-12-11 17:06 ` Chris Clayton
2017-12-11 17:17 ` Bjorn Helgaas
0 siblings, 2 replies; 7+ messages in thread
From: Sinan Kaya @ 2017-12-11 16:29 UTC (permalink / raw)
To: Chris Clayton, LKML; +Cc: bhelgaas
Hi Chris,
>
> I'm more than happy to provide additional diagnostics and test proposed fixes. As a starter for ten, I've attached the
> output from 'lspci -v'. If, however, you need to see the backtrace, I'll need some advice on how to capture that.
>
Can you open a bugzilla and also share the boot log?
There must be something unique about your system.
Sinan
--
Sinan Kaya
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Oops on 4.15-rc[123] on shutdown/reboot
2017-12-11 16:29 ` Sinan Kaya
@ 2017-12-11 17:06 ` Chris Clayton
2017-12-11 17:24 ` Sinan Kaya
2017-12-11 17:17 ` Bjorn Helgaas
1 sibling, 1 reply; 7+ messages in thread
From: Chris Clayton @ 2017-12-11 17:06 UTC (permalink / raw)
To: Sinan Kaya, LKML; +Cc: bhelgaas
[-- Attachment #1: Type: text/plain, Size: 571 bytes --]
On 11/12/17 16:29, Sinan Kaya wrote:
> Hi Chris,
>
>>
>> I'm more than happy to provide additional diagnostics and test proposed fixes. As a starter for ten, I've attached the
>> output from 'lspci -v'. If, however, you need to see the backtrace, I'll need some advice on how to capture that.
>>
>
> Can you open a bugzilla and also share the boot log?
>
Here's the output of dmesg for 4.15.0-rc3. I'll open a bugzilla later and add this and the lspci output that I sent with
my original repoart.
> There must be something unique about your system.
>
> Sinan
>
[-- Attachment #2: dmesg-4.15.0-rc3.log --]
[-- Type: text/x-log, Size: 46260 bytes --]
[ 0.000000] Linux version 4.15.0-rc3 (chris@laptop) (gcc version 7.2.1 20171207 (GCC)) #398 SMP PREEMPT Mon Dec 11 07:46:20 GMT 2017
[ 0.000000] Command line: ro root=/dev/sda2 resume=/dev/sda6 rootfstype=ext4 net.ifnames=0
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x001: 'x87 floating point registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x002: 'SSE registers'
[ 0.000000] x86/fpu: Supporting XSAVE feature 0x004: 'AVX registers'
[ 0.000000] x86/fpu: xstate_offset[2]: 576, xstate_sizes[2]: 256
[ 0.000000] x86/fpu: Enabled xstate features 0x7, context size is 832 bytes, using 'standard' format.
[ 0.000000] e820: BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: [mem 0x0000000000000100-0x000000000009d7ff] usable
[ 0.000000] BIOS-e820: [mem 0x000000000009d800-0x000000000009ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000000e0000-0x00000000000fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000000100000-0x00000000d7216fff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d7217000-0x00000000d721dfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000d721e000-0x00000000d7a0cfff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000d7a0d000-0x00000000d7ca1fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000d7ca2000-0x00000000db4dffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db4e0000-0x00000000db82dfff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000db82e000-0x00000000db88afff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000db88b000-0x00000000db9bcfff] ACPI NVS
[ 0.000000] BIOS-e820: [mem 0x00000000db9bd000-0x00000000dbffefff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000dbfff000-0x00000000dbffffff] usable
[ 0.000000] BIOS-e820: [mem 0x00000000dd000000-0x00000000df1fffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000f8000000-0x00000000fbffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fec00000-0x00000000fec00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed00000-0x00000000fed03fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fed1c000-0x00000000fed1ffff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000fee00000-0x00000000fee00fff] reserved
[ 0.000000] BIOS-e820: [mem 0x00000000ff000000-0x00000000ffffffff] reserved
[ 0.000000] BIOS-e820: [mem 0x0000000100000000-0x000000041fdfffff] usable
[ 0.000000] NX (Execute Disable) protection: active
[ 0.000000] random: fast init done
[ 0.000000] SMBIOS 2.7 present.
[ 0.000000] DMI: Notebook W65_67SZ /W65_67SZ , BIOS 1.03.05 02/26/2014
[ 0.000000] e820: update [mem 0x00000000-0x00000fff] usable ==> reserved
[ 0.000000] e820: remove [mem 0x000a0000-0x000fffff] usable
[ 0.000000] e820: last_pfn = 0x41fe00 max_arch_pfn = 0x400000000
[ 0.000000] MTRR default type: uncachable
[ 0.000000] MTRR fixed ranges enabled:
[ 0.000000] 00000-9FFFF write-back
[ 0.000000] A0000-BFFFF uncachable
[ 0.000000] C0000-CFFFF write-protect
[ 0.000000] D0000-E7FFF uncachable
[ 0.000000] E8000-FFFFF write-protect
[ 0.000000] MTRR variable ranges enabled:
[ 0.000000] 0 base 0000000000 mask 7C00000000 write-back
[ 0.000000] 1 base 0400000000 mask 7FE0000000 write-back
[ 0.000000] 2 base 00E0000000 mask 7FE0000000 uncachable
[ 0.000000] 3 base 00DE000000 mask 7FFE000000 uncachable
[ 0.000000] 4 base 00DD000000 mask 7FFF000000 uncachable
[ 0.000000] 5 base 041FE00000 mask 7FFFE00000 uncachable
[ 0.000000] 6 disabled
[ 0.000000] 7 disabled
[ 0.000000] 8 disabled
[ 0.000000] 9 disabled
[ 0.000000] x86/PAT: Configuration [0-7]: WB WC UC- UC WB WP UC- WT
[ 0.000000] e820: update [mem 0xdd000000-0xffffffff] usable ==> reserved
[ 0.000000] e820: last_pfn = 0xdc000 max_arch_pfn = 0x400000000
[ 0.000000] found SMP MP-table at [mem 0x000fd820-0x000fd82f] mapped at [ (ptrval)]
[ 0.000000] Base memory trampoline at [ (ptrval)] 97000 size 24576
[ 0.000000] Using GB pages for direct mapping
[ 0.000000] BRK [0x02098000, 0x02098fff] PGTABLE
[ 0.000000] BRK [0x02099000, 0x02099fff] PGTABLE
[ 0.000000] BRK [0x0209a000, 0x0209afff] PGTABLE
[ 0.000000] BRK [0x0209b000, 0x0209bfff] PGTABLE
[ 0.000000] BRK [0x0209c000, 0x0209cfff] PGTABLE
[ 0.000000] BRK [0x0209d000, 0x0209dfff] PGTABLE
[ 0.000000] ACPI: Early table checksum verification disabled
[ 0.000000] ACPI: RSDP 0x00000000000F0490 000024 (v02 ALASKA)
[ 0.000000] ACPI: XSDT 0x00000000DB993088 00008C (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FACP 0x00000000DB99FEA8 00010C (v05 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: DSDT 0x00000000DB9931A8 00CCFA (v02 ALASKA A M I 00000024 INTL 20091112)
[ 0.000000] ACPI: FACS 0x00000000DB9BB080 000040
[ 0.000000] ACPI: APIC 0x00000000DB99FFB8 000092 (v03 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: FPDT 0x00000000DB9A0050 000044 (v01 ALASKA A M I 01072009 AMI 00010013)
[ 0.000000] ACPI: ASF! 0x00000000DB9A0098 0000A5 (v32 INTEL HCG 00000001 TFSM 000F4240)
[ 0.000000] ACPI: SSDT 0x00000000DB9A0140 000F92 (v01 TrmRef PtidDevc 00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000DB9A10D8 000539 (v01 PmRef Cpu0Ist 00003000 INTL 20051117)
[ 0.000000] ACPI: SSDT 0x00000000DB9A1618 000AD8 (v01 PmRef CpuPm 00003000 INTL 20051117)
[ 0.000000] ACPI: MCFG 0x00000000DB9A20F0 00003C (v01 ALASKA A M I 01072009 MSFT 00000097)
[ 0.000000] ACPI: HPET 0x00000000DB9A2130 000038 (v01 ALASKA A M I 01072009 AMI. 00000005)
[ 0.000000] ACPI: SSDT 0x00000000DB9A2168 000315 (v01 SataRe SataTabl 00001000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000DB9A2480 001BFB (v01 SaSsdt SaSsdt 00003000 INTL 20091112)
[ 0.000000] ACPI: SSDT 0x00000000DB9A4080 000EA8 (v01 SgRef SgPeg 00001000 INTL 20091112)
[ 0.000000] ACPI: DMAR 0x00000000DB9A4F28 000090 (v01 INTEL HSW 00000001 INTL 00000001)
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] tsc: Fast TSC calibration using PIT
[ 0.000000] Zone ranges:
[ 0.000000] DMA [mem 0x0000000000001000-0x0000000000ffffff]
[ 0.000000] DMA32 [mem 0x0000000001000000-0x00000000ffffffff]
[ 0.000000] Normal [mem 0x0000000100000000-0x000000041fdfffff]
[ 0.000000] Movable zone start for each node
[ 0.000000] Early memory node ranges
[ 0.000000] node 0: [mem 0x0000000000001000-0x000000000009cfff]
[ 0.000000] node 0: [mem 0x0000000000100000-0x00000000d7216fff]
[ 0.000000] node 0: [mem 0x00000000d721e000-0x00000000d7a0cfff]
[ 0.000000] node 0: [mem 0x00000000d7ca2000-0x00000000db4dffff]
[ 0.000000] node 0: [mem 0x00000000db82e000-0x00000000db88afff]
[ 0.000000] node 0: [mem 0x00000000dbfff000-0x00000000dbffffff]
[ 0.000000] node 0: [mem 0x0000000100000000-0x000000041fdfffff]
[ 0.000000] Initmem setup node 0 [mem 0x0000000000001000-0x000000041fdfffff]
[ 0.000000] On node 0 totalpages: 4173886
[ 0.000000] DMA zone: 64 pages used for memmap
[ 0.000000] DMA zone: 21 pages reserved
[ 0.000000] DMA zone: 3996 pages, LIFO batch:0
[ 0.000000] DMA32 zone: 13963 pages used for memmap
[ 0.000000] DMA32 zone: 893602 pages, LIFO batch:31
[ 0.000000] Normal zone: 51192 pages used for memmap
[ 0.000000] Normal zone: 3276288 pages, LIFO batch:31
[ 0.000000] Reserved but unavailable: 100 pages
[ 0.000000] Reserving Intel graphics memory at 0x00000000dd200000-0x00000000df1fffff
[ 0.000000] ACPI: PM-Timer IO Port: 0x1808
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0xff] high edge lint[0x1])
[ 0.000000] IOAPIC[0]: apic_id 2, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] ACPI: HPET id: 0x8086a701 base: 0xfed00000
[ 0.000000] smpboot: Allowing 8 CPUs, 0 hotplug CPUs
[ 0.000000] PM: Registered nosave memory: [mem 0x00000000-0x00000fff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009d000-0x0009dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0x0009e000-0x0009ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000a0000-0x000dffff]
[ 0.000000] PM: Registered nosave memory: [mem 0x000e0000-0x000fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd7217000-0xd721dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xd7a0d000-0xd7ca1fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdb4e0000-0xdb82dfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdb88b000-0xdb9bcfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdb9bd000-0xdbffefff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdc000000-0xdcffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdd000000-0xdf1fffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xdf200000-0xf7ffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xf8000000-0xfbffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfc000000-0xfebfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec00000-0xfec00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfec01000-0xfecfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed00000-0xfed03fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed04000-0xfed1bfff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed1c000-0xfed1ffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfed20000-0xfedfffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee00000-0xfee00fff]
[ 0.000000] PM: Registered nosave memory: [mem 0xfee01000-0xfeffffff]
[ 0.000000] PM: Registered nosave memory: [mem 0xff000000-0xffffffff]
[ 0.000000] e820: [mem 0xdf200000-0xf7ffffff] available for PCI devices
[ 0.000000] clocksource: refined-jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645519600211568 ns
[ 0.000000] setup_percpu: NR_CPUS:8 nr_cpumask_bits:8 nr_cpu_ids:8 nr_node_ids:1
[ 0.000000] percpu: Embedded 35 pages/cpu @ (ptrval) s105944 r8192 d29224 u262144
[ 0.000000] pcpu-alloc: s105944 r8192 d29224 u262144 alloc=1*2097152
[ 0.000000] pcpu-alloc: [0] 0 1 2 3 4 5 6 7
[ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 4108646
[ 0.000000] Kernel command line: ro root=/dev/sda2 resume=/dev/sda6 rootfstype=ext4 net.ifnames=0
[ 0.000000] Dentry cache hash table entries: 2097152 (order: 12, 16777216 bytes)
[ 0.000000] Inode-cache hash table entries: 1048576 (order: 11, 8388608 bytes)
[ 0.000000] Memory: 16324568K/16695544K available (6679K kernel code, 661K rwdata, 2404K rodata, 840K init, 380K bss, 370976K reserved, 0K cma-reserved)
[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=8, Nodes=1
[ 0.000000] Preemptible hierarchical RCU implementation.
[ 0.000000] Tasks RCU enabled.
[ 0.000000] NR_IRQS: 4352, nr_irqs: 104, preallocated irqs: 16
[ 0.000000] Console: colour dummy device 80x25
[ 0.000000] console [tty0] enabled
[ 0.000000] ACPI: Core revision 20170831
[ 0.000000] ACPI: 7 ACPI AML tables successfully acquired and loaded
[ 0.000000] clocksource: hpet: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 133484882848 ns
[ 0.000000] hpet clockevent registered
[ 0.000000] APIC: Switch to symmetric I/O mode setup
[ 0.000000] ..TIMER: vector=0x30 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.020000] tsc: Fast TSC calibration using PIT
[ 0.024000] tsc: Detected 2494.227 MHz processor
[ 0.024000] Calibrating delay loop (skipped), value calculated using timer frequency.. 4988.45 BogoMIPS (lpj=9976908)
[ 0.024000] pid_max: default: 32768 minimum: 301
[ 0.024000] Mount-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.024000] Mountpoint-cache hash table entries: 32768 (order: 6, 262144 bytes)
[ 0.024000] CPU: Physical Processor ID: 0
[ 0.024000] CPU: Processor Core ID: 0
[ 0.024000] mce: CPU supports 9 MCE banks
[ 0.024000] CPU0: Thermal monitoring enabled (TM1)
[ 0.024000] process: using mwait in idle threads
[ 0.024000] Last level iTLB entries: 4KB 1024, 2MB 1024, 4MB 1024
[ 0.024000] Last level dTLB entries: 4KB 1024, 2MB 1024, 4MB 1024, 1GB 4
[ 0.024000] Freeing SMP alternatives memory: 28K
[ 0.024000] TSC deadline timer enabled
[ 0.024000] smpboot: CPU0: Intel(R) Core(TM) i7-4710MQ CPU @ 2.50GHz (family: 0x6, model: 0x3c, stepping: 0x3)
[ 0.040004] Performance Events: PEBS fmt2+, Haswell events, 16-deep LBR, full-width counters, Intel PMU driver.
[ 0.040035] ... version: 3
[ 0.040036] ... bit width: 48
[ 0.040037] ... generic registers: 4
[ 0.040039] ... value mask: 0000ffffffffffff
[ 0.040040] ... max period: 00007fffffffffff
[ 0.040041] ... fixed-purpose events: 3
[ 0.040042] ... event mask: 000000070000000f
[ 0.048001] Hierarchical SRCU implementation.
[ 0.064001] smp: Bringing up secondary CPUs ...
[ 0.092005] x86: Booting SMP configuration:
[ 0.092006] .... node #0, CPUs: #1 #2 #3 #4 #5 #6 #7
[ 0.260442] smp: Brought up 1 node, 8 CPUs
[ 0.260442] smpboot: Max logical packages: 1
[ 0.260442] smpboot: Total of 8 processors activated (39907.63 BogoMIPS)
[ 0.264151] devtmpfs: initialized
[ 0.264151] PM: Registering ACPI NVS region [mem 0xd7217000-0xd721dfff] (28672 bytes)
[ 0.264151] PM: Registering ACPI NVS region [mem 0xdb88b000-0xdb9bcfff] (1253376 bytes)
[ 0.264151] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 7645041785100000 ns
[ 0.264151] futex hash table entries: 2048 (order: 5, 131072 bytes)
[ 0.264151] NET: Registered protocol family 16
[ 0.264153] cpuidle: using governor ladder
[ 0.264153] cpuidle: using governor menu
[ 0.264153] ACPI FADT declares the system doesn't support PCIe ASPM, so disable it
[ 0.264153] ACPI: bus type PCI registered
[ 0.264153] PCI: Using configuration type 1 for base access
[ 0.264153] core: PMU erratum BJ122, BV98, HSD29 worked around, HT is on
[ 0.268038] ACPI: Added _OSI(Module Device)
[ 0.268040] ACPI: Added _OSI(Processor Device)
[ 0.268042] ACPI: Added _OSI(3.0 _SCP Extensions)
[ 0.268043] ACPI: Added _OSI(Processor Aggregator Device)
[ 0.268159] ACPI: Executed 1 blocks of module-level executable AML code
[ 0.277662] ACPI: [Firmware Bug]: BIOS _OSI(Linux) query ignored
[ 0.277926] ACPI: Dynamic OEM Table Load:
[ 0.277926] ACPI: SSDT 0xFFFF88040D0D8000 0003D3 (v01 PmRef Cpu0Cst 00003001 INTL 20051117)
[ 0.277926] ACPI: Dynamic OEM Table Load:
[ 0.277926] ACPI: SSDT 0xFFFF88040D120000 0005AA (v01 PmRef ApIst 00003000 INTL 20051117)
[ 0.277926] ACPI: Dynamic OEM Table Load:
[ 0.277926] ACPI: SSDT 0xFFFF88040DB85800 000119 (v01 PmRef ApCst 00003000 INTL 20051117)
[ 0.277926] ACPI: EC: EC started
[ 0.277926] ACPI: EC: interrupt blocked
[ 0.277926] ACPI: \_SB_.PCI0.LPCB.EC__: Used as first EC
[ 0.277926] ACPI: \_SB_.PCI0.LPCB.EC__: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.277926] ACPI: \_SB_.PCI0.LPCB.EC__: Used as boot DSDT EC to handle transactions
[ 0.277926] ACPI: Interpreter enabled
[ 0.277926] ACPI: (supports S0 S3 S4 S5)
[ 0.277926] ACPI: Using IOAPIC for interrupt routing
[ 0.277926] PCI: Using host bridge windows from ACPI; if necessary, use "pci=nocrs" and report a bug
[ 0.277926] ACPI: Enabled 7 GPEs in block 00 to 3F
[ 0.284558] ACPI: PCI Root Bridge [PCI0] (domain 0000 [bus 00-3e])
[ 0.284561] acpi PNP0A08:00: _OSC: OS supports [ASPM ClockPM Segments]
[ 0.284638] acpi PNP0A08:00: _OSC: not requesting OS control; OS requires [ExtendedConfig ASPM ClockPM MSI]
[ 0.284756] PCI host bridge to bus 0000:00
[ 0.284758] pci_bus 0000:00: root bus resource [io 0x0000-0x0cf7 window]
[ 0.284759] pci_bus 0000:00: root bus resource [io 0x0d00-0xffff window]
[ 0.284761] pci_bus 0000:00: root bus resource [mem 0x000a0000-0x000bffff window]
[ 0.284762] pci_bus 0000:00: root bus resource [mem 0x000d0000-0x000d3fff window]
[ 0.284764] pci_bus 0000:00: root bus resource [mem 0x000d4000-0x000d7fff window]
[ 0.284765] pci_bus 0000:00: root bus resource [mem 0x000d8000-0x000dbfff window]
[ 0.284767] pci_bus 0000:00: root bus resource [mem 0x000dc000-0x000dffff window]
[ 0.284768] pci_bus 0000:00: root bus resource [mem 0x000e0000-0x000e3fff window]
[ 0.284770] pci_bus 0000:00: root bus resource [mem 0x000e4000-0x000e7fff window]
[ 0.284771] pci_bus 0000:00: root bus resource [mem 0xdf200000-0xfeafffff window]
[ 0.284773] pci_bus 0000:00: root bus resource [bus 00-3e]
[ 0.284778] pci 0000:00:00.0: [8086:0c04] type 00 class 0x060000
[ 0.284831] pci 0000:00:01.0: [8086:0c01] type 01 class 0x060400
[ 0.284854] pci 0000:00:01.0: PME# supported from D0 D3hot D3cold
[ 0.284917] pci 0000:00:02.0: [8086:0416] type 00 class 0x030000
[ 0.284924] pci 0000:00:02.0: reg 0x10: [mem 0xf7800000-0xf7bfffff 64bit]
[ 0.284929] pci 0000:00:02.0: reg 0x18: [mem 0xe0000000-0xefffffff 64bit pref]
[ 0.284931] pci 0000:00:02.0: reg 0x20: [io 0xf000-0xf03f]
[ 0.284977] pci 0000:00:03.0: [8086:0c0c] type 00 class 0x040300
[ 0.284983] pci 0000:00:03.0: reg 0x10: [mem 0xf7f14000-0xf7f17fff 64bit]
[ 0.285048] pci 0000:00:14.0: [8086:8c31] type 00 class 0x0c0330
[ 0.285064] pci 0000:00:14.0: reg 0x10: [mem 0xf7f00000-0xf7f0ffff 64bit]
[ 0.285112] pci 0000:00:14.0: PME# supported from D3hot D3cold
[ 0.285152] pci 0000:00:16.0: [8086:8c3a] type 00 class 0x078000
[ 0.285169] pci 0000:00:16.0: reg 0x10: [mem 0xf7f1e000-0xf7f1e00f 64bit]
[ 0.285221] pci 0000:00:16.0: PME# supported from D0 D3hot D3cold
[ 0.285266] pci 0000:00:1a.0: [8086:8c2d] type 00 class 0x0c0320
[ 0.285284] pci 0000:00:1a.0: reg 0x10: [mem 0xf7f1c000-0xf7f1c3ff]
[ 0.285353] pci 0000:00:1a.0: PME# supported from D0 D3hot D3cold
[ 0.285396] pci 0000:00:1b.0: [8086:8c20] type 00 class 0x040300
[ 0.285409] pci 0000:00:1b.0: reg 0x10: [mem 0xf7f10000-0xf7f13fff 64bit]
[ 0.285461] pci 0000:00:1b.0: PME# supported from D0 D3hot D3cold
[ 0.285501] pci 0000:00:1c.0: [8086:8c10] type 01 class 0x060400
[ 0.285553] pci 0000:00:1c.0: PME# supported from D0 D3hot D3cold
[ 0.285612] pci 0000:00:1c.1: [8086:8c12] type 01 class 0x060400
[ 0.285664] pci 0000:00:1c.1: PME# supported from D0 D3hot D3cold
[ 0.285721] pci 0000:00:1c.2: [8086:8c14] type 01 class 0x060400
[ 0.285773] pci 0000:00:1c.2: PME# supported from D0 D3hot D3cold
[ 0.285829] pci 0000:00:1c.3: [8086:8c16] type 01 class 0x060400
[ 0.285881] pci 0000:00:1c.3: PME# supported from D0 D3hot D3cold
[ 0.285942] pci 0000:00:1d.0: [8086:8c26] type 00 class 0x0c0320
[ 0.285960] pci 0000:00:1d.0: reg 0x10: [mem 0xf7f1b000-0xf7f1b3ff]
[ 0.286029] pci 0000:00:1d.0: PME# supported from D0 D3hot D3cold
[ 0.286073] pci 0000:00:1f.0: [8086:8c49] type 00 class 0x060100
[ 0.286200] pci 0000:00:1f.2: [8086:8c03] type 00 class 0x010601
[ 0.286213] pci 0000:00:1f.2: reg 0x10: [io 0xf0b0-0xf0b7]
[ 0.286218] pci 0000:00:1f.2: reg 0x14: [io 0xf0a0-0xf0a3]
[ 0.286223] pci 0000:00:1f.2: reg 0x18: [io 0xf090-0xf097]
[ 0.286229] pci 0000:00:1f.2: reg 0x1c: [io 0xf080-0xf083]
[ 0.286234] pci 0000:00:1f.2: reg 0x20: [io 0xf060-0xf07f]
[ 0.286239] pci 0000:00:1f.2: reg 0x24: [mem 0xf7f1a000-0xf7f1a7ff]
[ 0.286266] pci 0000:00:1f.2: PME# supported from D3hot
[ 0.286302] pci 0000:00:1f.3: [8086:8c22] type 00 class 0x0c0500
[ 0.286316] pci 0000:00:1f.3: reg 0x10: [mem 0xf7f19000-0xf7f190ff 64bit]
[ 0.286332] pci 0000:00:1f.3: reg 0x20: [io 0xf040-0xf05f]
[ 0.286393] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.286419] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.286462] pci 0000:03:00.0: [10ec:5229] type 00 class 0xff0000
[ 0.286482] pci 0000:03:00.0: reg 0x10: [mem 0xf7e00000-0xf7e00fff]
[ 0.286596] pci 0000:03:00.0: supports D1 D2
[ 0.286596] pci 0000:03:00.0: PME# supported from D1 D2 D3hot
[ 0.296015] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.296020] pci 0000:00:1c.1: bridge window [mem 0xf7e00000-0xf7efffff]
[ 0.296074] pci 0000:04:00.0: [8086:08b1] type 00 class 0x028000
[ 0.296113] pci 0000:04:00.0: reg 0x10: [mem 0xf7d00000-0xf7d01fff 64bit]
[ 0.296274] pci 0000:04:00.0: PME# supported from D0 D3hot D3cold
[ 0.308016] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.308021] pci 0000:00:1c.2: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 0.308066] pci 0000:05:00.0: [10ec:5289] type 00 class 0xff0000
[ 0.308086] pci 0000:05:00.0: reg 0x10: [mem 0xf7c00000-0xf7c0ffff]
[ 0.308211] pci 0000:05:00.0: supports D1 D2
[ 0.308211] pci 0000:05:00.0: PME# supported from D1 D2 D3hot D3cold
[ 0.308260] pci 0000:05:00.2: [10ec:8168] type 00 class 0x020000
[ 0.308280] pci 0000:05:00.2: reg 0x10: [io 0xe000-0xe0ff]
[ 0.308307] pci 0000:05:00.2: reg 0x18: [mem 0xf0004000-0xf0004fff 64bit pref]
[ 0.308324] pci 0000:05:00.2: reg 0x20: [mem 0xf0000000-0xf0003fff 64bit pref]
[ 0.308397] pci 0000:05:00.2: supports D1 D2
[ 0.308398] pci 0000:05:00.2: PME# supported from D0 D1 D2 D3hot D3cold
[ 0.320016] pci 0000:00:1c.3: PCI bridge to [bus 05]
[ 0.320020] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
[ 0.320022] pci 0000:00:1c.3: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.320026] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.320047] pci_bus 0000:00: on NUMA node 0
[ 0.320539] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 5 6 10 *11 12 14 15), disabled.
[ 0.320578] ACPI: PCI Interrupt Link [LNKB] (IRQs *3 4 5 6 10 11 12 14 15), disabled.
[ 0.320614] ACPI: PCI Interrupt Link [LNKC] (IRQs 3 *4 5 6 10 11 12 14 15), disabled.
[ 0.320649] ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 6 *10 11 12 14 15), disabled.
[ 0.320684] ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.320719] ACPI: PCI Interrupt Link [LNKF] (IRQs 3 4 5 6 10 11 12 14 15) *0, disabled.
[ 0.320754] ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 *5 6 10 11 12 14 15), disabled.
[ 0.320789] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 10 *11 12 14 15), disabled.
[ 0.320989] ACPI: EC: interrupt unblocked
[ 0.320995] ACPI: EC: event unblocked
[ 0.321000] ACPI: \_SB_.PCI0.LPCB.EC__: GPE=0x17, EC_CMD/EC_SC=0x66, EC_DATA=0x62
[ 0.321002] ACPI: \_SB_.PCI0.LPCB.EC__: Used as boot DSDT EC to handle transactions and events
[ 0.321043] pci 0000:00:02.0: vgaarb: setting as boot VGA device
[ 0.321043] pci 0000:00:02.0: vgaarb: VGA device added: decodes=io+mem,owns=io+mem,locks=none
[ 0.321043] pci 0000:00:02.0: vgaarb: bridge control possible
[ 0.321043] vgaarb: loaded
[ 0.321043] SCSI subsystem initialized
[ 0.321043] libata version 3.00 loaded.
[ 0.321043] ACPI: bus type USB registered
[ 0.321043] usbcore: registered new interface driver usbfs
[ 0.321043] usbcore: registered new interface driver hub
[ 0.321043] usbcore: registered new device driver usb
[ 0.321043] Linux video capture interface: v2.00
[ 0.321043] Advanced Linux Sound Architecture Driver Initialized.
[ 0.321043] PCI: Using ACPI for IRQ routing
[ 0.321043] PCI: pci_cache_line_size set to 64 bytes
[ 0.321043] e820: reserve RAM buffer [mem 0x0009d800-0x0009ffff]
[ 0.321043] e820: reserve RAM buffer [mem 0xd7217000-0xd7ffffff]
[ 0.321043] e820: reserve RAM buffer [mem 0xd7a0d000-0xd7ffffff]
[ 0.321043] e820: reserve RAM buffer [mem 0xdb4e0000-0xdbffffff]
[ 0.321043] e820: reserve RAM buffer [mem 0xdb88b000-0xdbffffff]
[ 0.321043] e820: reserve RAM buffer [mem 0x41fe00000-0x41fffffff]
[ 0.321043] Bluetooth: Core ver 2.22
[ 0.321043] NET: Registered protocol family 31
[ 0.321043] Bluetooth: HCI device and connection manager initialized
[ 0.321043] Bluetooth: HCI socket layer initialized
[ 0.321043] Bluetooth: L2CAP socket layer initialized
[ 0.321043] Bluetooth: SCO socket layer initialized
[ 0.321043] clocksource: Switched to clocksource hpet
[ 0.321043] pnp: PnP ACPI init
[ 0.321043] system 00:00: [mem 0xfed40000-0xfed44fff] has been reserved
[ 0.321043] system 00:00: Plug and Play ACPI device, IDs PNP0c01 (active)
[ 0.321043] system 00:01: [io 0x0680-0x069f] has been reserved
[ 0.321043] system 00:01: [io 0xffff] has been reserved
[ 0.321043] system 00:01: [io 0xffff] has been reserved
[ 0.321043] system 00:01: [io 0xffff] has been reserved
[ 0.321043] system 00:01: [io 0x1c00-0x1cfe] has been reserved
[ 0.321043] system 00:01: [io 0x1d00-0x1dfe] has been reserved
[ 0.321043] system 00:01: [io 0x1e00-0x1efe] has been reserved
[ 0.321043] system 00:01: [io 0x1f00-0x1ffe] has been reserved
[ 0.321043] system 00:01: [io 0x1800-0x18fe] has been reserved
[ 0.321043] system 00:01: [io 0x164e-0x164f] has been reserved
[ 0.321043] system 00:01: [io 0x3322-0x3323] has been reserved
[ 0.321043] system 00:01: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.321043] pnp 00:02: Plug and Play ACPI device, IDs PNP0b00 (active)
[ 0.321043] system 00:03: [io 0x1854-0x1857] has been reserved
[ 0.321043] system 00:03: Plug and Play ACPI device, IDs INT3f0d PNP0c02 (active)
[ 0.321043] pnp 00:04: Plug and Play ACPI device, IDs PNP0303 (active)
[ 0.321043] pnp 00:05: Plug and Play ACPI device, IDs SYN1212 PNP0f13 (active)
[ 0.321043] system 00:06: [io 0x04d0-0x04d1] has been reserved
[ 0.321043] system 00:06: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.321043] system 00:07: [mem 0xfed1c000-0xfed1ffff] has been reserved
[ 0.321043] system 00:07: [mem 0xfed10000-0xfed17fff] has been reserved
[ 0.321043] system 00:07: [mem 0xfed18000-0xfed18fff] has been reserved
[ 0.321043] system 00:07: [mem 0xfed19000-0xfed19fff] has been reserved
[ 0.321043] system 00:07: [mem 0xf8000000-0xfbffffff] has been reserved
[ 0.321043] system 00:07: [mem 0xfed20000-0xfed3ffff] has been reserved
[ 0.321043] system 00:07: [mem 0xfed90000-0xfed93fff] has been reserved
[ 0.321043] system 00:07: [mem 0xfed45000-0xfed8ffff] has been reserved
[ 0.321043] system 00:07: [mem 0xff000000-0xffffffff] has been reserved
[ 0.321043] system 00:07: [mem 0xfee00000-0xfeefffff] could not be reserved
[ 0.321043] system 00:07: [mem 0xf7ffe000-0xf7ffefff] has been reserved
[ 0.321043] system 00:07: [mem 0xf7fe0000-0xf7fe0fff] has been reserved
[ 0.321043] system 00:07: Plug and Play ACPI device, IDs PNP0c02 (active)
[ 0.321043] pnp: PnP ACPI: found 8 devices
[ 0.325846] clocksource: acpi_pm: mask: 0xffffff max_cycles: 0xffffff, max_idle_ns: 2085701024 ns
[ 0.325872] pci 0000:00:01.0: PCI bridge to [bus 01]
[ 0.325877] pci 0000:00:1c.0: PCI bridge to [bus 02]
[ 0.325885] pci 0000:00:1c.1: PCI bridge to [bus 03]
[ 0.325889] pci 0000:00:1c.1: bridge window [mem 0xf7e00000-0xf7efffff]
[ 0.325894] pci 0000:00:1c.2: PCI bridge to [bus 04]
[ 0.325898] pci 0000:00:1c.2: bridge window [mem 0xf7d00000-0xf7dfffff]
[ 0.325904] pci 0000:00:1c.3: PCI bridge to [bus 05]
[ 0.325906] pci 0000:00:1c.3: bridge window [io 0xe000-0xefff]
[ 0.325910] pci 0000:00:1c.3: bridge window [mem 0xf7c00000-0xf7cfffff]
[ 0.325913] pci 0000:00:1c.3: bridge window [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.325918] pci_bus 0000:00: resource 4 [io 0x0000-0x0cf7 window]
[ 0.325919] pci_bus 0000:00: resource 5 [io 0x0d00-0xffff window]
[ 0.325919] pci_bus 0000:00: resource 6 [mem 0x000a0000-0x000bffff window]
[ 0.325920] pci_bus 0000:00: resource 7 [mem 0x000d0000-0x000d3fff window]
[ 0.325921] pci_bus 0000:00: resource 8 [mem 0x000d4000-0x000d7fff window]
[ 0.325921] pci_bus 0000:00: resource 9 [mem 0x000d8000-0x000dbfff window]
[ 0.325922] pci_bus 0000:00: resource 10 [mem 0x000dc000-0x000dffff window]
[ 0.325923] pci_bus 0000:00: resource 11 [mem 0x000e0000-0x000e3fff window]
[ 0.325923] pci_bus 0000:00: resource 12 [mem 0x000e4000-0x000e7fff window]
[ 0.325924] pci_bus 0000:00: resource 13 [mem 0xdf200000-0xfeafffff window]
[ 0.325925] pci_bus 0000:03: resource 1 [mem 0xf7e00000-0xf7efffff]
[ 0.325925] pci_bus 0000:04: resource 1 [mem 0xf7d00000-0xf7dfffff]
[ 0.325926] pci_bus 0000:05: resource 0 [io 0xe000-0xefff]
[ 0.325927] pci_bus 0000:05: resource 1 [mem 0xf7c00000-0xf7cfffff]
[ 0.325927] pci_bus 0000:05: resource 2 [mem 0xf0000000-0xf00fffff 64bit pref]
[ 0.325980] NET: Registered protocol family 2
[ 0.326048] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.326149] TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
[ 0.326237] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.326254] UDP hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.326280] UDP-Lite hash table entries: 8192 (order: 6, 262144 bytes)
[ 0.326325] NET: Registered protocol family 1
[ 0.326334] pci 0000:00:02.0: Video device with shadowed ROM at [mem 0x000c0000-0x000dffff]
[ 0.326607] PCI: CLS 64 bytes, default 64
[ 0.326616] PCI-DMA: Using software bounce buffering for IO (SWIOTLB)
[ 0.326618] software IO TLB [mem 0xd3217000-0xd7217000] (64MB) mapped at [000000008ed28af7-000000000781b2fd]
[ 0.326689] RAPL PMU: API unit is 2^-32 Joules, 4 fixed counters, 655360 ms ovfl timer
[ 0.326690] RAPL PMU: hw unit of domain pp0-core 2^-14 Joules
[ 0.326691] RAPL PMU: hw unit of domain package 2^-14 Joules
[ 0.326692] RAPL PMU: hw unit of domain dram 2^-14 Joules
[ 0.326693] RAPL PMU: hw unit of domain pp1-gpu 2^-14 Joules
[ 0.327029] Initialise system trusted keyrings
[ 0.327055] workingset: timestamp_bits=62 max_order=22 bucket_order=0
[ 0.328024] Key type cifs.spnego registered
[ 0.328027] fuse init (API version 7.26)
[ 0.328727] Key type asymmetric registered
[ 0.328729] Asymmetric key parser 'x509' registered
[ 0.328746] Block layer SCSI generic (bsg) driver version 0.4 loaded (major 252)
[ 0.328748] io scheduler noop registered
[ 0.328765] io scheduler cfq registered (default)
[ 0.328766] io scheduler mq-deadline registered
[ 0.329225] intel_idle: MWAIT substates: 0x42120
[ 0.329226] intel_idle: v0.4.1 model 0x3C
[ 0.329428] intel_idle: lapic_timer_reliable_states 0xffffffff
[ 0.329481] ACPI: AC Adapter [AC] (on-line)
[ 0.329519] input: Power Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0C:00/input/input0
[ 0.329537] ACPI: Power Button [PWRB]
[ 0.329567] input: Sleep Button as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0E:00/input/input1
[ 0.329583] ACPI: Sleep Button [SLPB]
[ 0.329613] input: Lid Switch as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0C0D:00/input/input2
[ 0.329623] ACPI: Lid Switch [LID0]
[ 0.329645] input: Power Button as /devices/LNXSYSTM:00/LNXPWRBN:00/input/input3
[ 0.329652] ACPI: Power Button [PWRF]
[ 0.329948] thermal LNXTHERM:00: registered as thermal_zone0
[ 0.329950] ACPI: Thermal Zone [TZ0] (14 C)
[ 0.330301] ACPI: Battery Slot [BAT0] (battery present)
[ 0.333742] Serial: 8250/16550 driver, 4 ports, IRQ sharing disabled
[ 0.333905] Linux agpgart interface v0.103
[ 0.334091] pmd_set_huge: Cannot satisfy [mem 0xf7800000-0xf7a00000] with a huge-page mapping due to MTRR override.
[ 0.334205] [drm] Memory usable by graphics device = 2048M
[ 0.334207] [drm] Replacing VGA console driver
[ 0.340238] [drm] Supports vblank timestamp caching Rev 2 (21.10.2013).
[ 0.340240] [drm] Driver supports precise vblank timestamp query.
[ 0.342264] i915 0000:00:02.0: vgaarb: changed VGA decodes: olddecodes=io+mem,decodes=io+mem:owns=io+mem
[ 0.367749] [drm] Initialized i915 1.6.0 20171023 for 0000:00:02.0 on minor 0
[ 0.367868] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 0.368063] input: Video Bus as /devices/LNXSYSTM:00/LNXSYBUS:00/PNP0A08:00/LNXVIDEO:01/input/input4
[ 0.369422] ahci 0000:00:1f.2: version 3.0
[ 0.369487] ahci 0000:00:1f.2: SSS flag set, parallel bus scan disabled
[ 0.369510] ahci 0000:00:1f.2: AHCI 0001.0300 32 slots 4 ports 6 Gbps 0x25 impl SATA mode
[ 0.369525] ahci 0000:00:1f.2: flags: 64bit ncq stag led clo pio slum part ems sxs apst
[ 0.392112] fbcon: inteldrmfb (fb0) is primary device
[ 0.392601] scsi host0: ahci
[ 0.392867] scsi host1: ahci
[ 0.393100] scsi host2: ahci
[ 0.393227] scsi host3: ahci
[ 0.393303] scsi host4: ahci
[ 0.393385] scsi host5: ahci
[ 0.393413] ata1: SATA max UDMA/133 abar m2048@0xf7f1a000 port 0xf7f1a100 irq 19
[ 0.393413] ata2: DUMMY
[ 0.393414] ata3: SATA max UDMA/133 abar m2048@0xf7f1a000 port 0xf7f1a200 irq 19
[ 0.393415] ata4: DUMMY
[ 0.393415] ata5: DUMMY
[ 0.393416] ata6: SATA max UDMA/133 abar m2048@0xf7f1a000 port 0xf7f1a380 irq 19
[ 0.393435] ehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driver
[ 0.393437] ehci-pci: EHCI PCI platform driver
[ 0.393516] ehci-pci 0000:00:1a.0: EHCI Host Controller
[ 0.393521] ehci-pci 0000:00:1a.0: new USB bus registered, assigned bus number 1
[ 0.393530] ehci-pci 0000:00:1a.0: debug port 2
[ 0.397433] ehci-pci 0000:00:1a.0: cache line size of 64 is not supported
[ 0.397436] ehci-pci 0000:00:1a.0: irq 16, io mem 0xf7f1c000
[ 0.412025] ehci-pci 0000:00:1a.0: USB 2.0 started, EHCI 1.00
[ 0.412054] usb usb1: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.412055] usb usb1: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.412056] usb usb1: Product: EHCI Host Controller
[ 0.412056] usb usb1: Manufacturer: Linux 4.15.0-rc3 ehci_hcd
[ 0.412057] usb usb1: SerialNumber: 0000:00:1a.0
[ 0.412156] hub 1-0:1.0: USB hub found
[ 0.412159] hub 1-0:1.0: 2 ports detected
[ 0.412316] ehci-pci 0000:00:1d.0: EHCI Host Controller
[ 0.412319] ehci-pci 0000:00:1d.0: new USB bus registered, assigned bus number 2
[ 0.412327] ehci-pci 0000:00:1d.0: debug port 2
[ 0.416234] ehci-pci 0000:00:1d.0: cache line size of 64 is not supported
[ 0.416240] ehci-pci 0000:00:1d.0: irq 23, io mem 0xf7f1b000
[ 0.432031] ehci-pci 0000:00:1d.0: USB 2.0 started, EHCI 1.00
[ 0.432056] usb usb2: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.432057] usb usb2: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.432058] usb usb2: Product: EHCI Host Controller
[ 0.432059] usb usb2: Manufacturer: Linux 4.15.0-rc3 ehci_hcd
[ 0.432059] usb usb2: SerialNumber: 0000:00:1d.0
[ 0.432132] hub 2-0:1.0: USB hub found
[ 0.432135] hub 2-0:1.0: 2 ports detected
[ 0.432215] uhci_hcd: USB Universal Host Controller Interface driver
[ 0.432302] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.432305] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 3
[ 0.433369] xhci_hcd 0000:00:14.0: hcc params 0x200077c1 hci version 0x100 quirks 0x00009810
[ 0.433373] xhci_hcd 0000:00:14.0: cache line size of 64 is not supported
[ 0.433429] usb usb3: New USB device found, idVendor=1d6b, idProduct=0002
[ 0.433430] usb usb3: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.433431] usb usb3: Product: xHCI Host Controller
[ 0.433431] usb usb3: Manufacturer: Linux 4.15.0-rc3 xhci-hcd
[ 0.433432] usb usb3: SerialNumber: 0000:00:14.0
[ 0.433488] hub 3-0:1.0: USB hub found
[ 0.433501] hub 3-0:1.0: 14 ports detected
[ 0.434014] xhci_hcd 0000:00:14.0: xHCI Host Controller
[ 0.434015] xhci_hcd 0000:00:14.0: new USB bus registered, assigned bus number 4
[ 0.434037] usb usb4: New USB device found, idVendor=1d6b, idProduct=0003
[ 0.434037] usb usb4: New USB device strings: Mfr=3, Product=2, SerialNumber=1
[ 0.434038] usb usb4: Product: xHCI Host Controller
[ 0.434038] usb usb4: Manufacturer: Linux 4.15.0-rc3 xhci-hcd
[ 0.434039] usb usb4: SerialNumber: 0000:00:14.0
[ 0.434080] hub 4-0:1.0: USB hub found
[ 0.434088] hub 4-0:1.0: 4 ports detected
[ 0.434258] usbcore: registered new interface driver usb-storage
[ 0.434262] usbcore: registered new interface driver ums-realtek
[ 0.434276] i8042: PNP: PS/2 Controller [PNP0303:PS2K,PNP0f13:SYNM] at 0x60,0x64 irq 1,12
[ 0.706179] ata1: SATA link up 1.5 Gbps (SStatus 113 SControl 300)
[ 0.707801] ata1.00: ATAPI: MATSHITABD-MLT UJ260AF, 1.00, max UDMA/133
[ 0.708902] ata1.00: configured for UDMA/133
[ 0.955144] i8042: Detected active multiplexing controller, rev 1.1
[ 0.956653] serio: i8042 KBD port at 0x60,0x64 irq 1
[ 0.956671] serio: i8042 AUX0 port at 0x60,0x64 irq 12
[ 0.956681] serio: i8042 AUX1 port at 0x60,0x64 irq 12
[ 0.956690] serio: i8042 AUX2 port at 0x60,0x64 irq 12
[ 0.956698] serio: i8042 AUX3 port at 0x60,0x64 irq 12
[ 0.956809] mousedev: PS/2 mouse device common for all mice
[ 0.957059] rtc_cmos 00:02: RTC can wake from S4
[ 0.957154] rtc_cmos 00:02: rtc core: registered rtc_cmos as rtc0
[ 0.957174] rtc_cmos 00:02: alarms up to one month, y3k, 242 bytes nvram, hpet irqs
[ 0.957182] i2c /dev entries driver
[ 0.957337] i801_smbus 0000:00:1f.3: SPD Write Disable is set
[ 0.957350] i801_smbus 0000:00:1f.3: SMBus using PCI interrupt
[ 0.957893] usbcore: registered new interface driver uvcvideo
[ 0.957893] USB Video Class driver (1.1.1)
[ 0.957897] intel_pstate: Intel P-state driver initializing
[ 0.958233] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 0.958234] NET: Registered protocol family 17
[ 0.958237] NET: Registered protocol family 15
[ 0.958242] Key type dns_resolver registered
[ 0.959488] microcode: sig=0x306c3, pf=0x10, revision=0x22
[ 0.959603] microcode: Microcode Update Driver: v2.2.
[ 0.959608] sched_clock: Marking stable (959600398, 0)->(938816348, 20784050)
[ 0.959784] registered taskstats version 1
[ 0.959784] Loading compiled-in X.509 certificates
[ 0.960079] rtc_cmos 00:02: setting system clock to 2017-12-11 16:57:18 UTC (1513011438)
[ 0.961229] input: AT Translated Set 2 keyboard as /devices/platform/i8042/serio0/input/input5
[ 1.180030] usb 1-1: new high-speed USB device number 2 using ehci-pci
[ 1.180038] usb 2-1: new high-speed USB device number 2 using ehci-pci
[ 1.180042] usb 3-6: new full-speed USB device number 2 using xhci_hcd
[ 1.330052] usb 3-6: New USB device found, idVendor=046d, idProduct=c534
[ 1.330053] usb 3-6: New USB device strings: Mfr=1, Product=2, SerialNumber=0
[ 1.330054] usb 3-6: Product: USB Receiver
[ 1.330054] usb 3-6: Manufacturer: Logitech
[ 1.336362] usb 2-1: New USB device found, idVendor=8087, idProduct=8000
[ 1.336364] usb 2-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.336386] usb 1-1: New USB device found, idVendor=8087, idProduct=8008
[ 1.336387] usb 1-1: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.336520] hub 1-1:1.0: USB hub found
[ 1.336536] hub 2-1:1.0: USB hub found
[ 1.336608] hub 1-1:1.0: 6 ports detected
[ 1.336611] hub 2-1:1.0: 8 ports detected
[ 1.340009] tsc: Refined TSC clocksource calibration: 2494.224 MHz
[ 1.340015] clocksource: tsc: mask: 0xffffffffffffffff max_cycles: 0x23f3e9a353a, max_idle_ns: 440795330815 ns
[ 1.456028] usb 3-7: new full-speed USB device number 3 using xhci_hcd
[ 1.605218] usb 3-7: New USB device found, idVendor=8087, idProduct=07dc
[ 1.605219] usb 3-7: New USB device strings: Mfr=0, Product=0, SerialNumber=0
[ 1.631712] Console: switching to colour frame buffer device 200x56
[ 1.692193] i915 0000:00:02.0: fb0: inteldrmfb frame buffer device
[ 1.694125] scsi 0:0:0:0: CD-ROM MATSHITA BD-MLT UJ260AF 1.00 PQ: 0 ANSI: 5
[ 1.726514] sr 0:0:0:0: [sr0] scsi3-mmc drive: 24x/24x writer dvd-ram cd/rw xa/form2 cdda tray
[ 1.727314] cdrom: Uniform CD-ROM driver Revision: 3.20
[ 1.728138] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.728194] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 2.042940] ata3: SATA link down (SStatus 0 SControl 300)
[ 2.358784] ata6: SATA link up 6.0 Gbps (SStatus 133 SControl 300)
[ 2.364099] clocksource: Switched to clocksource tsc
[ 2.371798] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 2.371800] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 2.372608] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2.499247] ata6.00: ATA-10: ST2000LM007-1R8174, SBK2, max UDMA/133
[ 2.500075] ata6.00: 3907029168 sectors, multi 16: LBA48 NCQ (depth 31/32), AA
[ 2.523935] ata6.00: ACPI cmd ef/10:06:00:00:00:00 (SET FEATURES) succeeded
[ 2.523937] ata6.00: ACPI cmd f5/00:00:00:00:00:00 (SECURITY FREEZE LOCK) filtered out
[ 2.524805] ata6.00: ACPI cmd b1/c1:00:00:00:00:00 (DEVICE CONFIGURATION OVERLAY) filtered out
[ 2.562662] ata6.00: configured for UDMA/133
[ 2.563600] scsi 5:0:0:0: Direct-Access ATA ST2000LM007-1R81 SBK2 PQ: 0 ANSI: 5
[ 2.564556] sd 5:0:0:0: [sda] 3907029168 512-byte logical blocks: (2.00 TB/1.82 TiB)
[ 2.564577] sd 5:0:0:0: Attached scsi generic sg1 type 0
[ 2.565911] sd 5:0:0:0: [sda] 4096-byte physical blocks
[ 2.566523] sd 5:0:0:0: [sda] Write Protect is off
[ 2.567133] sd 5:0:0:0: [sda] Mode Sense: 00 3a 00 00
[ 2.567138] sd 5:0:0:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 3.304278] sda: sda1 sda2 sda3 sda4 < sda5 sda6 sda7 sda8 sda9 sda10 sda11 sda12 >
[ 3.305999] sd 5:0:0:0: [sda] Attached SCSI disk
[ 3.393012] ALSA device list:
[ 3.393888] No soundcards found.
[ 3.539777] EXT4-fs (sda2): mounted filesystem with ordered data mode. Opts: (null)
[ 3.540567] VFS: Mounted root (ext4 filesystem) readonly on device 8:2.
[ 3.581535] devtmpfs: mounted
[ 3.582915] Freeing unused kernel memory: 840K
[ 3.583574] Write protecting the kernel read-only data: 12288k
[ 3.584523] Freeing unused kernel memory: 1488K
[ 3.587538] Freeing unused kernel memory: 1692K
[ 3.592106] x86/mm: Checked W+X mappings: passed, no W+X pages found.
[ 5.565923] udevd[244]: starting version 3.2.4
[ 5.770589] udevd[245]: starting eudev-3.2.4
[ 6.097773] random: crng init done
[ 6.105819] r8169 Gigabit Ethernet driver 2.3LK-NAPI loaded
[ 6.106514] r8169 0000:05:00.2: can't disable ASPM; OS doesn't have ASPM control
[ 6.107821] r8169 0000:05:00.2 eth0: RTL8411 at 0x00000000f723fee4, 80:fa:5b:08:d0:3d, XID 08800880 IRQ 19
[ 6.108531] r8169 0000:05:00.2 eth0: jumbo features [frames: 9200 bytes, tx checksumming: ko]
[ 6.369795] snd_hda_intel 0000:00:03.0: bound 0000:00:02.0 (ops 0xffffffff8187fc20)
[ 6.464313] usbcore: registered new interface driver btusb
[ 6.477992] Bluetooth: hci0: read Intel version: 3707100180012d0d27
[ 6.478939] Bluetooth: hci0: Intel device is already patched. patch num: 27
[ 6.514294] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb3/3-6/3-6:1.0/0003:046D:C534.0001/input/input10
[ 6.572128] hid-generic 0003:046D:C534.0001: input: USB HID v1.11 Keyboard [Logitech USB Receiver] on usb-0000:00:14.0-6/input0
[ 6.574922] input: Logitech USB Receiver as /devices/pci0000:00/0000:00:14.0/usb3/3-6/3-6:1.1/0003:046D:C534.0002/input/input11
[ 6.604977] snd_hda_codec_via hdaudioC1D0: autoconfig for VT1802: line_outs=1 (0x24/0x0/0x0/0x0/0x0) type:speaker
[ 6.605757] snd_hda_codec_via hdaudioC1D0: speaker_outs=0 (0x0/0x0/0x0/0x0/0x0)
[ 6.606533] snd_hda_codec_via hdaudioC1D0: hp_outs=1 (0x25/0x0/0x0/0x0/0x0)
[ 6.607302] snd_hda_codec_via hdaudioC1D0: mono: mono_out=0x0
[ 6.608110] snd_hda_codec_via hdaudioC1D0: inputs:
[ 6.608902] snd_hda_codec_via hdaudioC1D0: Internal Mic=0x30
[ 6.609039] input: HDA Intel HDMI HDMI/DP,pcm=3 as /devices/pci0000:00/0000:00:03.0/sound/card0/input12
[ 6.610533] snd_hda_codec_via hdaudioC1D0: Mic=0x2b
[ 6.616479] input: HDA Intel PCH Mic as /devices/pci0000:00/0000:00:1b.0/sound/card1/input17
[ 6.632216] hid-generic 0003:046D:C534.0002: input,hiddev96: USB HID v1.11 Mouse [Logitech USB Receiver] on usb-0000:00:14.0-6/input1
[ 6.632231] input: HDA Intel HDMI HDMI/DP,pcm=7 as /devices/pci0000:00/0000:00:03.0/sound/card0/input13
[ 6.632274] input: HDA Intel HDMI HDMI/DP,pcm=8 as /devices/pci0000:00/0000:00:03.0/sound/card0/input14
[ 6.632313] input: HDA Intel PCH Front Headphone as /devices/pci0000:00/0000:00:1b.0/sound/card1/input18
[ 6.632489] input: HDA Intel HDMI HDMI/DP,pcm=9 as /devices/pci0000:00/0000:00:03.0/sound/card0/input15
[ 6.632535] input: HDA Intel HDMI HDMI/DP,pcm=10 as /devices/pci0000:00/0000:00:03.0/sound/card0/input16
[ 6.637602] usbcore: registered new interface driver usbhid
[ 6.638422] usbhid: USB HID core driver
[ 8.246886] Adding 16777212k swap on /dev/sda6. Priority:1 extents:1 across:16777212k
[ 8.259204] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 8.394006] EXT4-fs (sda2): re-mounted. Opts: (null)
[ 8.863509] EXT4-fs (sda8): mounted filesystem with ordered data mode. Opts: (null)
[ 8.935739] EXT4-fs (sda9): mounted filesystem with ordered data mode. Opts: (null)
[ 9.041400] EXT4-fs (sda10): mounted filesystem with ordered data mode. Opts: (null)
[ 9.135125] EXT4-fs (sda11): mounted filesystem with ordered data mode. Opts: (null)
[ 104.071401] nf_conntrack version 0.5.0 (65536 buckets, 262144 max)
[ 104.542968] r8169 0000:05:00.2 eth0: link down
[ 104.543732] r8169 0000:05:00.2 eth0: link down
[ 106.081401] r8169 0000:05:00.2 eth0: link up
[ 107.579177] Bluetooth: BNEP (Ethernet Emulation) ver 1.3
[ 107.580183] Bluetooth: BNEP filters: protocol multicast
[ 107.580987] Bluetooth: BNEP socket layer initialized
[ 145.681195] Bluetooth: RFCOMM TTY layer initialized
[ 145.681200] Bluetooth: RFCOMM socket layer initialized
[ 145.681203] Bluetooth: RFCOMM ver 1.11
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Oops on 4.15-rc[123] on shutdown/reboot
2017-12-11 16:29 ` Sinan Kaya
2017-12-11 17:06 ` Chris Clayton
@ 2017-12-11 17:17 ` Bjorn Helgaas
2017-12-11 20:04 ` Chris Clayton
1 sibling, 1 reply; 7+ messages in thread
From: Bjorn Helgaas @ 2017-12-11 17:17 UTC (permalink / raw)
To: Sinan Kaya; +Cc: Chris Clayton, LKML, bhelgaas, linux-pci
[+cc linux-pci]
On Mon, Dec 11, 2017 at 11:29:50AM -0500, Sinan Kaya wrote:
> Hi Chris,
>
> >
> > I'm more than happy to provide additional diagnostics and test proposed fixes. As a starter for ten, I've attached the
> > output from 'lspci -v'. If, however, you need to see the backtrace, I'll need some advice on how to capture that.
> >
>
> Can you open a bugzilla and also share the boot log?
>
> There must be something unique about your system.
Can you attach "lspci -vv" output (as root) to the bugzilla, too?
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Oops on 4.15-rc[123] on shutdown/reboot
2017-12-11 17:06 ` Chris Clayton
@ 2017-12-11 17:24 ` Sinan Kaya
2017-12-11 19:31 ` Chris Clayton
0 siblings, 1 reply; 7+ messages in thread
From: Sinan Kaya @ 2017-12-11 17:24 UTC (permalink / raw)
To: Chris Clayton, LKML; +Cc: bhelgaas
On 12/11/2017 12:06 PM, Chris Clayton wrote:
> Here's the output of dmesg for 4.15.0-rc3. I'll open a bugzilla later and add this and the lspci output that I sent with
> my original repoart.
This was helpful. I don't see any AER/DPC in your log. It looks like the only PCIe
portdrv service you have is PME.
Can we do a quick hack and return immediately from
static int pcie_pme_probe(struct pcie_device *srv)
by putting return 0; at the top.
Same thing in
static void pcie_pme_remove(struct pcie_device *srv)
just place a return at the top.
I'm hoping your problem will go away after this. Then, we can start peeling the onion.
--
Sinan Kaya
Qualcomm Datacenter Technologies, Inc. as an affiliate of Qualcomm Technologies, Inc.
Qualcomm Technologies, Inc. is a member of the Code Aurora Forum, a Linux Foundation Collaborative Project.
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Oops on 4.15-rc[123] on shutdown/reboot
2017-12-11 17:24 ` Sinan Kaya
@ 2017-12-11 19:31 ` Chris Clayton
0 siblings, 0 replies; 7+ messages in thread
From: Chris Clayton @ 2017-12-11 19:31 UTC (permalink / raw)
To: Sinan Kaya, LKML; +Cc: bhelgaas
On 11/12/17 17:24, Sinan Kaya wrote:
> On 12/11/2017 12:06 PM, Chris Clayton wrote:
>> Here's the output of dmesg for 4.15.0-rc3. I'll open a bugzilla later and add this and the lspci output that I sent with
>> my original repoart.
>
> This was helpful. I don't see any AER/DPC in your log. It looks like the only PCIe
> portdrv service you have is PME.
>
> Can we do a quick hack and return immediately from
>
> static int pcie_pme_probe(struct pcie_device *srv)
>
> by putting return 0; at the top.
>
> Same thing in
>
> static void pcie_pme_remove(struct pcie_device *srv)
>
> just place a return at the top.
>
I made those changes (to drivers/pci/pcie/pme.c) and built and installed the kernel. Sorry, but I still get the oops
when I reboot.
> I'm hoping your problem will go away after this. Then, we can start peeling the onion.
>
^ permalink raw reply [flat|nested] 7+ messages in thread
* Re: Oops on 4.15-rc[123] on shutdown/reboot
2017-12-11 17:17 ` Bjorn Helgaas
@ 2017-12-11 20:04 ` Chris Clayton
0 siblings, 0 replies; 7+ messages in thread
From: Chris Clayton @ 2017-12-11 20:04 UTC (permalink / raw)
To: Bjorn Helgaas, Sinan Kaya; +Cc: LKML, bhelgaas, linux-pci
On 11/12/17 17:17, Bjorn Helgaas wrote:
> [+cc linux-pci]
>
> On Mon, Dec 11, 2017 at 11:29:50AM -0500, Sinan Kaya wrote:
>> Hi Chris,
>>
>>>
>>> I'm more than happy to provide additional diagnostics and test proposed fixes. As a starter for ten, I've attached the
>>> output from 'lspci -v'. If, however, you need to see the backtrace, I'll need some advice on how to capture that.
>>>
>>
>> Can you open a bugzilla and also share the boot log?
>>
>> There must be something unique about your system.
>
> Can you attach "lspci -vv" output (as root) to the bugzilla, too?
>
I've opened the bugzilla report (Bug 198141) and attached the dmesg and lspci -vv outputs to it.
^ permalink raw reply [flat|nested] 7+ messages in thread
end of thread, other threads:[~2017-12-11 20:04 UTC | newest]
Thread overview: 7+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2017-12-11 15:31 Oops on 4.15-rc[123] on shutdown/reboot Chris Clayton
2017-12-11 16:29 ` Sinan Kaya
2017-12-11 17:06 ` Chris Clayton
2017-12-11 17:24 ` Sinan Kaya
2017-12-11 19:31 ` Chris Clayton
2017-12-11 17:17 ` Bjorn Helgaas
2017-12-11 20:04 ` Chris Clayton
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®