* [PATCH v9 2/3] pwm: rp1: Add RP1 PWM controller driver
2026-09-18 9:58 [PATCH v9 0/3] Add RP1 PWM controller support Andrea della Porta
2026-09-18 9:59 ` [PATCH v9 1/3] dt-bindings: pwm: Add Raspberry Pi RP1 PWM controller Andrea della Porta
@ 2026-09-18 9:59 ` Andrea della Porta
2026-09-18 9:59 ` [PATCH v9 3/3] arm64: dts: broadcom: rpi-5: Add RP1 PWM node Andrea della Porta
2 siblings, 0 replies; 4+ messages in thread
From: Andrea della Porta @ 2026-09-18 9:59 UTC (permalink / raw)
To: Uwe Kleine-König, linux-pwm, Rob Herring,
Krzysztof Kozlowski, Conor Dooley, Florian Fainelli,
Broadcom internal kernel review list, Andrea della Porta,
devicetree, linux-rpi-kernel, linux-arm-kernel, linux-kernel,
Naushir Patuck, Stanimir Varbanov, mbrugger, Sean Young,
Julian Braha, Gary Guo, Christophe JAILLET
From: Naushir Patuck <naush@raspberrypi.com>
The Raspberry Pi RP1 southbridge features an embedded PWM
controller with 4 output channels, alongside an RPM interface
to read the fan speed on the Raspberry Pi 5.
Add the supporting driver.
Signed-off-by: Naushir Patuck <naush@raspberrypi.com>
Co-developed-by: Stanimir Varbanov <svarbanov@suse.de>
Signed-off-by: Stanimir Varbanov <svarbanov@suse.de>
Signed-off-by: Andrea della Porta <andrea.porta@suse.com>
---
drivers/pwm/Kconfig | 8 +
drivers/pwm/Makefile | 1 +
drivers/pwm/pwm-rp1.c | 499 ++++++++++++++++++++++
include/soc/bcm2835/raspberrypi-pwm-rp1.h | 10 +
4 files changed, 518 insertions(+)
create mode 100644 drivers/pwm/pwm-rp1.c
create mode 100644 include/soc/bcm2835/raspberrypi-pwm-rp1.h
diff --git a/drivers/pwm/Kconfig b/drivers/pwm/Kconfig
index 7297760868790..e1baec8d294d1 100644
--- a/drivers/pwm/Kconfig
+++ b/drivers/pwm/Kconfig
@@ -637,6 +637,14 @@ config PWM_ROCKCHIP
Generic PWM framework driver for the PWM controller found on
Rockchip SoCs.
+config PWM_RASPBERRYPI_RP1
+ tristate "RP1 PWM support"
+ depends on MISC_RP1 || COMPILE_TEST
+ depends on HAS_IOMEM
+ select REGMAP_MMIO
+ help
+ PWM framework driver for Raspberry Pi RP1 controller.
+
config PWM_SAMSUNG
tristate "Samsung PWM support"
depends on PLAT_SAMSUNG || ARCH_S5PV210 || ARCH_EXYNOS || COMPILE_TEST
diff --git a/drivers/pwm/Makefile b/drivers/pwm/Makefile
index 5630a521a7cff..c07fd24f69f39 100644
--- a/drivers/pwm/Makefile
+++ b/drivers/pwm/Makefile
@@ -57,6 +57,7 @@ obj-$(CONFIG_PWM_RENESAS_RZG2L_GPT) += pwm-rzg2l-gpt.o
obj-$(CONFIG_PWM_RENESAS_RZ_MTU3) += pwm-rz-mtu3.o
obj-$(CONFIG_PWM_RENESAS_TPU) += pwm-renesas-tpu.o
obj-$(CONFIG_PWM_ROCKCHIP) += pwm-rockchip.o
+obj-$(CONFIG_PWM_RASPBERRYPI_RP1) += pwm-rp1.o
obj-$(CONFIG_PWM_SAMSUNG) += pwm-samsung.o
obj-$(CONFIG_PWM_SIFIVE) += pwm-sifive.o
obj-$(CONFIG_PWM_SL28CPLD) += pwm-sl28cpld.o
diff --git a/drivers/pwm/pwm-rp1.c b/drivers/pwm/pwm-rp1.c
new file mode 100644
index 0000000000000..cfd38e46cc589
--- /dev/null
+++ b/drivers/pwm/pwm-rp1.c
@@ -0,0 +1,499 @@
+// SPDX-License-Identifier: GPL-2.0
+/*
+ * pwm-rp1.c
+ *
+ * Raspberry Pi RP1 PWM.
+ *
+ * Copyright © 2026 Raspberry Pi Ltd.
+ *
+ * Author: Naushir Patuck (naush@raspberrypi.com)
+ *
+ * Based on the pwm-bcm2835 driver by:
+ * Bart Tanghe <bart.tanghe@thomasmore.be>
+ *
+ * Datasheet: https://pip-assets.raspberrypi.com/categories/892-raspberry-pi-5/documents/RP-008370-DS-1-rp1-peripherals.pdf?disposition=inline
+ *
+ * Limitations:
+ * - Channels can be enabled/disabled through a global update flag, while the
+ * period and duty per-channel registers are independently updatable, and
+ * they are latched on the end of (specific channel) period strobe.
+ * This means that period and duty changes might result in glitches if the
+ * period/duty is changed exactly during an end of period strobe.
+ * - Since the duty/period registers are freely updatable (do not depend on
+ * the global update flag), setting one of them close to the period end and
+ * the other right afterwards results in a mixed output for that cycle because
+ * the write ops are not atomic.
+ * - The global update flag prevents mis-sampling of multi-bit bus signals in
+ * the PWM clock domain. This ensures that all PWM channel settings update
+ * on the same PWM clock cycle. Channels start in sync only if they share the
+ * same period.
+ * - If both duty and period are set to 0, the output is a constant low signal
+ * if polarity is normal or a constant high signal if polarity is inversed.
+ * - When disabled the output is driven to 0 if polarity is normal, or to 1
+ * if polarity is inversed.
+ * - Disabling the PWM stops the output immediately, without waiting for current
+ * period to complete first.
+ * - Channels are phase-capable, but on RPi5, the firmware can use a channel
+ * phase register to report the RPM of the fan connected to that PWM
+ * channel. As a result, phase control will be ignored for now.
+ */
+
+#include <linux/bitfield.h>
+#include <linux/bitops.h>
+#include <linux/clk.h>
+#include <linux/err.h>
+#include <linux/io.h>
+#include <linux/module.h>
+#include <linux/of.h>
+#include <linux/platform_device.h>
+#include <linux/pwm.h>
+#include <linux/regmap.h>
+#include <linux/units.h>
+#include <soc/bcm2835/raspberrypi-pwm-rp1.h>
+
+#define RP1_PWM_GLB_CTRL 0x000
+#define RP1_PWM_GLB_CTRL_CHANNEL_ENABLE(chan) BIT(chan)
+#define RP1_PWM_GLB_CTRL_SET_UPDATE BIT(31)
+
+#define RP1_PWM_CHAN_CTRL(chan) (0x014 + ((chan) * 0x10))
+#define RP1_PWM_CHAN_CTRL_POLARITY BIT(3)
+#define RP1_PWM_CHAN_CTRL_FIFO_POP_MASK BIT(8)
+#define RP1_PWM_CHAN_CTRL_MODE GENMASK(2, 0)
+enum rp1_pwm_ctrl_mode {
+ RP1_PWM_CHAN_CTRL_MODE_ZERO,
+ RP1_PWM_CHAN_CTRL_MODE_TE_MS,
+ RP1_PWM_CHAN_CTRL_MODE_PC_MS,
+ RP1_PWM_CHAN_CTRL_MODE_PD_ENC,
+ RP1_PWM_CHAN_CTRL_MODE_MSB_SER,
+ RP1_PWM_CHAN_CTRL_MODE_PPM,
+ RP1_PWM_CHAN_CTRL_MODE_LE_MS,
+ RP1_PWM_CHAN_CTRL_MODE_LSB_SER,
+};
+
+#define RP1_PWM_CHAN_CTRL_DEFAULT (RP1_PWM_CHAN_CTRL_FIFO_POP_MASK + \
+ FIELD_PREP(RP1_PWM_CHAN_CTRL_MODE, \
+ RP1_PWM_CHAN_CTRL_MODE_TE_MS))
+
+#define RP1_PWM_RANGE(chan) (0x018 + ((chan) * 0x10))
+#define RP1_PWM_PHASE(chan) (0x01C + ((chan) * 0x10))
+#define RP1_PWM_DUTY(chan) (0x020 + ((chan) * 0x10))
+
+#define RP1_PWM_NUM_PWMS 4
+
+struct rp1_pwm {
+ struct regmap *regmap;
+ struct clk *clk;
+ unsigned long clk_rate;
+ bool clk_enabled;
+ struct mutex lock; /* sync pm ops with read_tachometer */
+};
+
+struct rp1_pwm_waveform {
+ u32 period_ticks;
+ u32 duty_ticks;
+ bool enabled;
+ bool inverted_polarity;
+};
+
+static const struct regmap_config rp1_pwm_regmap_config = {
+ .reg_bits = 32,
+ .val_bits = 32,
+ .reg_stride = 4,
+ .max_register = 0x60,
+};
+
+static int rp1_pwm_apply_config(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+ u32 value;
+ int ret;
+
+ /* update the changed registers on the next strobe to avoid glitches */
+ ret = regmap_read(rp1->regmap, RP1_PWM_GLB_CTRL, &value);
+ if (ret)
+ return ret;
+ value |= RP1_PWM_GLB_CTRL_SET_UPDATE;
+ regmap_write(rp1->regmap, RP1_PWM_GLB_CTRL, value);
+
+ return 0;
+}
+
+static int rp1_pwm_request(struct pwm_chip *chip, struct pwm_device *pwm)
+{
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+
+ /* init channel to reset defaults, preserving the polarity bit */
+ regmap_update_bits(rp1->regmap, RP1_PWM_CHAN_CTRL(pwm->hwpwm),
+ ~(u32)RP1_PWM_CHAN_CTRL_POLARITY, RP1_PWM_CHAN_CTRL_DEFAULT);
+ return 0;
+}
+
+static int rp1_pwm_round_waveform_tohw(struct pwm_chip *chip,
+ struct pwm_device *pwm,
+ const struct pwm_waveform *wf,
+ void *_wfhw)
+{
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+ u64 period_ticks, duty_ticks, offset_ticks;
+ struct rp1_pwm_waveform *wfhw = _wfhw;
+ u64 clk_rate = rp1->clk_rate;
+ int ret = 0;
+
+ if (!wf->period_length_ns) {
+ *wfhw = (typeof(*wfhw)){
+ .enabled = false,
+ .inverted_polarity = false,
+ };
+ return 0;
+ }
+
+ period_ticks = mul_u64_u64_div_u64(wf->period_length_ns, clk_rate, NSEC_PER_SEC);
+
+ /*
+ * The period is limited to U32_MAX, and it will be decremented by one later
+ * to allow 100% duty cycle.
+ */
+ if (period_ticks > U32_MAX) {
+ period_ticks = U32_MAX;
+ } else if (period_ticks < 2) {
+ period_ticks = 2;
+ ret = 1;
+ }
+
+ duty_ticks = mul_u64_u64_div_u64(wf->duty_length_ns, clk_rate, NSEC_PER_SEC);
+ duty_ticks = min(duty_ticks, period_ticks);
+ offset_ticks = mul_u64_u64_div_u64(wf->duty_offset_ns, clk_rate, NSEC_PER_SEC);
+ if (offset_ticks >= period_ticks)
+ offset_ticks = period_ticks - 1;
+ if (duty_ticks && offset_ticks &&
+ duty_ticks + offset_ticks >= period_ticks) {
+ wfhw->duty_ticks = period_ticks - duty_ticks;
+ wfhw->inverted_polarity = true;
+ } else {
+ wfhw->duty_ticks = duty_ticks;
+ wfhw->inverted_polarity = false;
+ }
+ /* Account for the extra tick at the end of the period */
+ wfhw->period_ticks = period_ticks - 1;
+
+ wfhw->enabled = true;
+
+ return ret;
+}
+
+static int rp1_pwm_round_waveform_fromhw(struct pwm_chip *chip,
+ struct pwm_device *pwm,
+ const void *_wfhw,
+ struct pwm_waveform *wf)
+{
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+ const struct rp1_pwm_waveform *wfhw = _wfhw;
+ u64 clk_rate = rp1->clk_rate;
+ u64 ticks;
+
+ *wf = (struct pwm_waveform){ };
+
+ if (!wfhw->enabled)
+ return 0;
+
+ wf->period_length_ns = DIV_ROUND_UP_ULL(((u64)wfhw->period_ticks + 1) * NSEC_PER_SEC,
+ (u32)clk_rate);
+
+ if (!wfhw->inverted_polarity) {
+ wf->duty_length_ns = DIV_ROUND_UP_ULL((u64)wfhw->duty_ticks * NSEC_PER_SEC,
+ (u32)clk_rate);
+ } else {
+ if (wfhw->duty_ticks > (u64)wfhw->period_ticks + 1) {
+ /* 100% duty cycle case */
+ ticks = 0;
+ } else {
+ ticks = (u64)wfhw->period_ticks + 1 - wfhw->duty_ticks;
+ }
+ wf->duty_length_ns = DIV_ROUND_UP_ULL(ticks * NSEC_PER_SEC, (u32)clk_rate);
+ wf->duty_offset_ns = DIV_ROUND_UP_ULL((u64)(wfhw->period_ticks + 1 - ticks) *
+ NSEC_PER_SEC, (u32)clk_rate);
+ }
+
+ return 0;
+}
+
+static int rp1_pwm_write_waveform(struct pwm_chip *chip,
+ struct pwm_device *pwm,
+ const void *_wfhw)
+{
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+ const struct rp1_pwm_waveform *wfhw = _wfhw;
+ u32 value, ctrl;
+ int ret;
+
+ /* set polarity */
+ ret = regmap_read(rp1->regmap, RP1_PWM_CHAN_CTRL(pwm->hwpwm), &value);
+ if (ret)
+ return ret;
+ if (!wfhw->inverted_polarity)
+ value &= ~RP1_PWM_CHAN_CTRL_POLARITY;
+ else
+ value |= RP1_PWM_CHAN_CTRL_POLARITY;
+ regmap_write(rp1->regmap, RP1_PWM_CHAN_CTRL(pwm->hwpwm), value);
+
+ /* early exit if disabled */
+ ret = regmap_read(rp1->regmap, RP1_PWM_GLB_CTRL, &ctrl);
+ if (ret)
+ return ret;
+ if (!wfhw->enabled) {
+ ctrl &= ~RP1_PWM_GLB_CTRL_CHANNEL_ENABLE(pwm->hwpwm);
+ /* just disable the channel and bail out early */
+ regmap_write(rp1->regmap, RP1_PWM_GLB_CTRL, ctrl);
+ return rp1_pwm_apply_config(chip, pwm);
+ }
+
+ /* set period and duty cycle */
+ regmap_write(rp1->regmap,
+ RP1_PWM_RANGE(pwm->hwpwm), wfhw->period_ticks);
+ regmap_write(rp1->regmap,
+ RP1_PWM_DUTY(pwm->hwpwm), wfhw->duty_ticks);
+
+ /* enable the channel */
+ ctrl |= RP1_PWM_GLB_CTRL_CHANNEL_ENABLE(pwm->hwpwm);
+ regmap_write(rp1->regmap, RP1_PWM_GLB_CTRL, ctrl);
+
+ return rp1_pwm_apply_config(chip, pwm);
+}
+
+static int rp1_pwm_read_waveform(struct pwm_chip *chip,
+ struct pwm_device *pwm,
+ void *_wfhw)
+{
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+ struct rp1_pwm_waveform *wfhw = _wfhw;
+ u32 value;
+ int ret;
+
+ *wfhw = (typeof(*wfhw)) {
+ .period_ticks = 0,
+ .duty_ticks = 0,
+ };
+
+ ret = regmap_read(rp1->regmap, RP1_PWM_GLB_CTRL, &value);
+ if (ret)
+ return ret;
+ wfhw->enabled = !!(value & RP1_PWM_GLB_CTRL_CHANNEL_ENABLE(pwm->hwpwm));
+
+ ret = regmap_read(rp1->regmap, RP1_PWM_CHAN_CTRL(pwm->hwpwm), &value);
+ if (ret)
+ return ret;
+ wfhw->inverted_polarity = !!(value & RP1_PWM_CHAN_CTRL_POLARITY);
+
+ if (wfhw->enabled) {
+ ret = regmap_read(rp1->regmap, RP1_PWM_RANGE(pwm->hwpwm), &wfhw->period_ticks);
+ if (ret)
+ return ret;
+ ret = regmap_read(rp1->regmap, RP1_PWM_DUTY(pwm->hwpwm), &wfhw->duty_ticks);
+ if (ret)
+ return ret;
+ }
+
+ return 0;
+}
+
+static const struct pwm_ops rp1_pwm_ops = {
+ .sizeof_wfhw = sizeof(struct rp1_pwm_waveform),
+ .request = rp1_pwm_request,
+ .round_waveform_tohw = rp1_pwm_round_waveform_tohw,
+ .round_waveform_fromhw = rp1_pwm_round_waveform_fromhw,
+ .read_waveform = rp1_pwm_read_waveform,
+ .write_waveform = rp1_pwm_write_waveform,
+};
+
+int rp1_pwm_read_tachometer(struct device *dev)
+{
+ struct pwm_chip *chip;
+ struct rp1_pwm *rp1;
+ u32 tach_val;
+ int ret;
+
+ if (!dev)
+ return -EINVAL;
+
+ device_lock(dev);
+
+ chip = dev_get_drvdata(dev);
+ if (!chip) {
+ ret = -ENODEV;
+ goto err_dev_unlock;
+ }
+
+ rp1 = pwmchip_get_drvdata(chip);
+ if (!rp1) {
+ ret = -ENODEV;
+ goto err_dev_unlock;
+ }
+
+ mutex_lock(&rp1->lock);
+ if (!rp1->clk_enabled) {
+ ret = -EBUSY;
+ goto err_clk_unlock;
+ }
+
+ ret = regmap_read(rp1->regmap, RP1_PWM_PHASE(2), &tach_val);
+ if (ret)
+ goto err_clk_unlock;
+
+ ret = (int)tach_val;
+
+err_clk_unlock:
+ mutex_unlock(&rp1->lock);
+err_dev_unlock:
+ device_unlock(dev);
+
+ return ret;
+}
+EXPORT_SYMBOL_NS_GPL(rp1_pwm_read_tachometer, "RP1_PWM_FAN");
+
+static int rp1_pwm_probe(struct platform_device *pdev)
+{
+ struct device *dev = &pdev->dev;
+ unsigned long clk_rate;
+ struct pwm_chip *chip;
+ void __iomem *base;
+ struct rp1_pwm *rp1;
+ int ret;
+
+ chip = devm_pwmchip_alloc(dev, RP1_PWM_NUM_PWMS, sizeof(*rp1));
+ if (IS_ERR(chip))
+ return PTR_ERR(chip);
+
+ rp1 = pwmchip_get_drvdata(chip);
+ ret = devm_mutex_init(dev, &rp1->lock);
+ if (ret)
+ return ret;
+
+ base = devm_platform_ioremap_resource(pdev, 0);
+ if (IS_ERR(base))
+ return PTR_ERR(base);
+
+ rp1->regmap = devm_regmap_init_mmio(dev, base, &rp1_pwm_regmap_config);
+ if (IS_ERR(rp1->regmap))
+ return dev_err_probe(dev, PTR_ERR(rp1->regmap), "Cannot initialize regmap\n");
+
+ rp1->clk = devm_clk_get(dev, NULL);
+ if (IS_ERR(rp1->clk))
+ return dev_err_probe(dev, PTR_ERR(rp1->clk), "Clock not found\n");
+
+ ret = clk_prepare_enable(rp1->clk);
+ if (ret)
+ return dev_err_probe(dev, ret, "Failed to enable clock\n");
+ rp1->clk_enabled = true;
+
+ ret = devm_clk_rate_exclusive_get(dev, rp1->clk);
+ if (ret) {
+ dev_err_probe(dev, ret, "Failed to get exclusive rate\n");
+ goto err_disable_clk;
+ }
+
+ clk_rate = clk_get_rate(rp1->clk);
+ if (!clk_rate) {
+ ret = dev_err_probe(dev, -EINVAL, "Failed to get clock rate\n");
+ goto err_disable_clk;
+ }
+ /*
+ * To prevent u64 overflow in period calculations:
+ * mul_u64_u64_div_u64(period_ns, clk_rate, NSEC_PER_SEC)
+ * If clk_rate > 1 GHz, the result can overflow.
+ */
+ if (clk_rate > HZ_PER_GHZ) {
+ ret = dev_err_probe(dev, -EINVAL, "Clock rate > 1 GHz is not supported\n");
+ goto err_disable_clk;
+ }
+ rp1->clk_rate = clk_rate;
+
+ chip->ops = &rp1_pwm_ops;
+ chip->atomic = true;
+
+ platform_set_drvdata(pdev, chip);
+
+ ret = pwmchip_add(chip);
+ if (ret) {
+ dev_err_probe(dev, ret, "Failed to register PWM chip\n");
+ goto err_disable_clk;
+ }
+
+ return 0;
+
+err_disable_clk:
+ clk_disable_unprepare(rp1->clk);
+
+ return ret;
+}
+
+static void rp1_pwm_remove(struct platform_device *pdev)
+{
+ struct pwm_chip *chip = platform_get_drvdata(pdev);
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+
+ pwmchip_remove(chip);
+
+ if (rp1->clk_enabled) {
+ clk_disable_unprepare(rp1->clk);
+ rp1->clk_enabled = false;
+ }
+}
+
+static int rp1_pwm_suspend(struct device *dev)
+{
+ struct pwm_chip *chip = dev_get_drvdata(dev);
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+
+ mutex_lock(&rp1->lock);
+ if (rp1->clk_enabled) {
+ clk_disable_unprepare(rp1->clk);
+ rp1->clk_enabled = false;
+ }
+ mutex_unlock(&rp1->lock);
+
+ return 0;
+}
+
+static int rp1_pwm_resume(struct device *dev)
+{
+ struct pwm_chip *chip = dev_get_drvdata(dev);
+ struct rp1_pwm *rp1 = pwmchip_get_drvdata(chip);
+ int ret;
+
+ mutex_lock(&rp1->lock);
+ ret = clk_prepare_enable(rp1->clk);
+ if (ret) {
+ dev_err(dev, "Failed to enable clock on resume: %pe\n", ERR_PTR(ret));
+ goto err_unlock;
+ }
+ rp1->clk_enabled = true;
+
+err_unlock:
+ mutex_unlock(&rp1->lock);
+
+ return ret;
+}
+
+static DEFINE_SIMPLE_DEV_PM_OPS(rp1_pwm_pm_ops, rp1_pwm_suspend, rp1_pwm_resume);
+
+static const struct of_device_id rp1_pwm_of_match[] = {
+ { .compatible = "raspberrypi,rp1-pwm" },
+ { /* sentinel */ }
+};
+MODULE_DEVICE_TABLE(of, rp1_pwm_of_match);
+
+static struct platform_driver rp1_pwm_driver = {
+ .probe = rp1_pwm_probe,
+ .remove = rp1_pwm_remove,
+ .driver = {
+ .name = "rp1-pwm",
+ .of_match_table = rp1_pwm_of_match,
+ .pm = pm_ptr(&rp1_pwm_pm_ops),
+ },
+};
+module_platform_driver(rp1_pwm_driver);
+
+MODULE_DESCRIPTION("RP1 PWM driver");
+MODULE_AUTHOR("Naushir Patuck <naush@raspberrypi.com>");
+MODULE_AUTHOR("Andrea della Porta <andrea.porta@suse.com>");
+MODULE_LICENSE("GPL");
diff --git a/include/soc/bcm2835/raspberrypi-pwm-rp1.h b/include/soc/bcm2835/raspberrypi-pwm-rp1.h
new file mode 100644
index 0000000000000..3be0892da667e
--- /dev/null
+++ b/include/soc/bcm2835/raspberrypi-pwm-rp1.h
@@ -0,0 +1,10 @@
+/* SPDX-License-Identifier: GPL-2.0 */
+
+#ifndef __SOC_RASPBERRY_PWM_RP1_H__
+#define __SOC_RASPBERRY_PWM_RP1_H__
+
+#include <linux/device.h>
+
+int rp1_pwm_read_tachometer(struct device *dev);
+
+#endif /* __SOC_RASPBERRY_PWM_RP1_H__ */
--
2.35.3
^ permalink raw reply [flat|nested] 4+ messages in thread