[PATCH v2 0/4] Add samsung-matisselte and common matisse dtsi

[PATCH v2 0/4] Add samsung-matisselte and common matisse dtsi

[Stefan Hansson]

This series adds a common samsung-matisse dtsi and reworks
samsung-matisse-wifi to use it, and introduces samsung-matisselte. I
choose matisselte over matisse-lte as this is how most other devices
(klte, s3ve3g) do it and it is the codename that Samsung gave the
device. See individual commits for more information.

---
Changes since v1:

 - Rebased on latest linux-next
 - Added qcom,msm8226 compatible to matisselte inspired by recent Lumia
   830 patch. This is done as in v1, the patch was rejected because I
   included the msm8226 dtsi despite not marking matisselte as
   compatible with msm8226, and I was not sure how to resolve that. As
   such, I'm copying what was done in the Lumia 830 (microsoft-tesla)
   patch given that it was accepted.

Stefan Hansson (4):
  ARM: dts: qcom: samsung-matisse-common: Add initial common device tree
  dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE
  ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 LTE
    (SM-T535)
  ARM: dts: qcom: samsung-matisse-common: Add UART

 .../devicetree/bindings/arm/qcom.yaml         |   1 +
 arch/arm/boot/dts/qcom/Makefile               |   1 +
 .../qcom-apq8026-samsung-matisse-wifi.dts     | 467 +----------------
 .../qcom-msm8226-samsung-matisse-common.dtsi  | 478 ++++++++++++++++++
 .../qcom/qcom-msm8926-samsung-matisselte.dts  |  36 ++
 5 files changed, 525 insertions(+), 458 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts

-- 
2.41.0

[PATCH v2 1/4] ARM: dts: qcom: samsung-matisse-common: Add initial common device tree

[Stefan Hansson]

According to the dts from the kernel source code released by Samsung,
matissewifi and matisselte only have minor differences in hardware, so
use a shared dtsi to reduce duplicated code. Additionally, this should
make adding support for matisse3g easier should someone want to do that
at a later point.

As such, add a common device tree for all matisse devices by Samsung
based on the matissewifi dts. Support for matisselte will be introduced
in a later patch in this series and will use the common dtsi as well.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
---
 .../qcom-apq8026-samsung-matisse-wifi.dts     | 467 +----------------
 .../qcom-msm8226-samsung-matisse-common.dtsi  | 474 ++++++++++++++++++
 2 files changed, 483 insertions(+), 458 deletions(-)
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi

diff --git a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
index f516e0426bb9..98d4bb797617 100644
--- a/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
+++ b/arch/arm/boot/dts/qcom/qcom-apq8026-samsung-matisse-wifi.dts
@@ -5,222 +5,12 @@
 
 /dts-v1/;
 
-#include <dt-bindings/input/input.h>
-#include "qcom-msm8226.dtsi"
-#include "qcom-pm8226.dtsi"
-
-/delete-node/ &adsp_region;
-/delete-node/ &smem_region;
+#include "qcom-msm8226-samsung-matisse-common.dtsi"
 
 / {
 	model = "Samsung Galaxy Tab 4 10.1";
 	compatible = "samsung,matisse-wifi", "qcom,apq8026";
 	chassis-type = "tablet";
-
-	aliases {
-		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
-		mmc1 = &sdhc_2; /* SDC2 SD card slot */
-		display0 = &framebuffer0;
-	};
-
-	chosen {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		stdout-path = "display0";
-
-		framebuffer0: framebuffer@3200000 {
-			compatible = "simple-framebuffer";
-			reg = <0x03200000 0x800000>;
-			width = <1280>;
-			height = <800>;
-			stride = <(1280 * 3)>;
-			format = "r8g8b8";
-		};
-	};
-
-	gpio-hall-sensor {
-		compatible = "gpio-keys";
-
-		event-hall-sensor {
-			label = "Hall Effect Sensor";
-			gpios = <&tlmm 110 GPIO_ACTIVE_LOW>;
-			linux,input-type = <EV_SW>;
-			linux,code = <SW_LID>;
-			debounce-interval = <15>;
-			linux,can-disable;
-			wakeup-source;
-		};
-	};
-
-	gpio-keys {
-		compatible = "gpio-keys";
-		autorepeat;
-
-		key-home {
-			label = "Home";
-			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_HOMEPAGE>;
-			debounce-interval = <15>;
-		};
-
-		key-volume-down {
-			label = "Volume Down";
-			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEDOWN>;
-			debounce-interval = <15>;
-		};
-
-		key-volume-up {
-			label = "Volume Up";
-			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
-			linux,code = <KEY_VOLUMEUP>;
-			debounce-interval = <15>;
-		};
-	};
-
-	i2c-backlight {
-		compatible = "i2c-gpio";
-		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
-
-		pinctrl-0 = <&backlight_i2c_default_state>;
-		pinctrl-names = "default";
-
-		i2c-gpio,delay-us = <4>;
-
-		#address-cells = <1>;
-		#size-cells = <0>;
-
-		backlight@2c {
-			compatible = "ti,lp8556";
-			reg = <0x2c>;
-
-			dev-ctrl = /bits/ 8 <0x80>;
-			init-brt = /bits/ 8 <0x3f>;
-
-			pwms = <&backlight_pwm 0 100000>;
-			pwm-names = "lp8556";
-
-			rom-a0h {
-				rom-addr = /bits/ 8 <0xa0>;
-				rom-val = /bits/ 8 <0x44>;
-			};
-
-			rom-a1h {
-				rom-addr = /bits/ 8 <0xa1>;
-				rom-val = /bits/ 8 <0x6c>;
-			};
-
-			rom-a5h {
-				rom-addr = /bits/ 8 <0xa5>;
-				rom-val = /bits/ 8 <0x24>;
-			};
-		};
-	};
-
-	backlight_pwm: pwm {
-		compatible = "clk-pwm";
-		#pwm-cells = <2>;
-		clocks = <&mmcc CAMSS_GP0_CLK>;
-		pinctrl-0 = <&backlight_pwm_default_state>;
-		pinctrl-names = "default";
-	};
-
-	reg_tsp_1p8v: regulator-tsp-1p8v {
-		compatible = "regulator-fixed";
-		regulator-name = "tsp_1p8v";
-		regulator-min-microvolt = <1800000>;
-		regulator-max-microvolt = <1800000>;
-
-		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_en_default_state>;
-	};
-
-	reg_tsp_3p3v: regulator-tsp-3p3v {
-		compatible = "regulator-fixed";
-		regulator-name = "tsp_3p3v";
-		regulator-min-microvolt = <3300000>;
-		regulator-max-microvolt = <3300000>;
-
-		gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
-		enable-active-high;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&tsp_en1_default_state>;
-	};
-
-	reserved-memory {
-		#address-cells = <1>;
-		#size-cells = <1>;
-		ranges;
-
-		framebuffer@3200000 {
-			reg = <0x03200000 0x800000>;
-			no-map;
-		};
-
-		mpss@8400000 {
-			reg = <0x08400000 0x1f00000>;
-			no-map;
-		};
-
-		mba@a300000 {
-			reg = <0x0a300000 0x100000>;
-			no-map;
-		};
-
-		reserved@cb00000 {
-			reg = <0x0cb00000 0x700000>;
-			no-map;
-		};
-
-		wcnss@d200000 {
-			reg = <0x0d200000 0x700000>;
-			no-map;
-		};
-
-		adsp_region: adsp@d900000 {
-			reg = <0x0d900000 0x1800000>;
-			no-map;
-		};
-
-		venus@f100000 {
-			reg = <0x0f100000 0x500000>;
-			no-map;
-		};
-
-		smem_region: smem@fa00000 {
-			reg = <0x0fa00000 0x100000>;
-			no-map;
-		};
-
-		reserved@fb00000 {
-			reg = <0x0fb00000 0x260000>;
-			no-map;
-		};
-
-		rfsa@fd60000 {
-			reg = <0x0fd60000 0x20000>;
-			no-map;
-		};
-
-		rmtfs@fd80000 {
-			compatible = "qcom,rmtfs-mem";
-			reg = <0x0fd80000 0x180000>;
-			no-map;
-
-			qcom,client-id = <1>;
-		};
-	};
-};
-
-&adsp {
-	status = "okay";
 };
 
 &blsp1_i2c2 {
@@ -243,21 +33,6 @@ accelerometer@1d {
 	};
 };
 
-&blsp1_i2c4 {
-	status = "okay";
-
-	muic: usb-switch@25 {
-		compatible = "siliconmitus,sm5502-muic";
-		reg = <0x25>;
-
-		interrupt-parent = <&tlmm>;
-		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
-
-		pinctrl-names = "default";
-		pinctrl-0 = <&muic_int_default_state>;
-	};
-};
-
 &blsp1_i2c5 {
 	status = "okay";
 
@@ -278,242 +53,18 @@ touchscreen@4a {
 	};
 };
 
-&rpm_requests {
-	regulators {
-		compatible = "qcom,rpm-pm8226-regulators";
-
-		pm8226_s3: s3 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		pm8226_s4: s4 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_s5: s5 {
-			regulator-min-microvolt = <1150000>;
-			regulator-max-microvolt = <1150000>;
-		};
-
-		pm8226_l1: l1 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1225000>;
-		};
-
-		pm8226_l2: l2 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8226_l3: l3 {
-			regulator-min-microvolt = <750000>;
-			regulator-max-microvolt = <1337500>;
-			regulator-always-on;
-		};
-
-		pm8226_l4: l4 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8226_l5: l5 {
-			regulator-min-microvolt = <1200000>;
-			regulator-max-microvolt = <1200000>;
-		};
-
-		pm8226_l6: l6 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		pm8226_l7: l7 {
-			regulator-min-microvolt = <1850000>;
-			regulator-max-microvolt = <1850000>;
-		};
-
-		pm8226_l8: l8 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-			regulator-always-on;
-		};
-
-		pm8226_l9: l9 {
-			regulator-min-microvolt = <2050000>;
-			regulator-max-microvolt = <2050000>;
-		};
-
-		pm8226_l10: l10 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_l12: l12 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_l14: l14 {
-			regulator-min-microvolt = <2750000>;
-			regulator-max-microvolt = <2750000>;
-		};
-
-		pm8226_l15: l15 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		pm8226_l16: l16 {
-			regulator-min-microvolt = <3000000>;
-			regulator-max-microvolt = <3350000>;
-		};
-
-		pm8226_l17: l17 {
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-
-			regulator-system-load = <200000>;
-			regulator-allow-set-load;
-			regulator-always-on;
-		};
-
-		pm8226_l18: l18 {
-			regulator-min-microvolt = <2950000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8226_l19: l19 {
-			regulator-min-microvolt = <2850000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		pm8226_l20: l20 {
-			regulator-min-microvolt = <3075000>;
-			regulator-max-microvolt = <3075000>;
-		};
-
-		pm8226_l21: l21 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8226_l22: l22 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <3000000>;
-		};
-
-		pm8226_l23: l23 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <3300000>;
-		};
-
-		pm8226_l24: l24 {
-			regulator-min-microvolt = <1300000>;
-			regulator-max-microvolt = <1350000>;
-		};
-
-		pm8226_l25: l25 {
-			regulator-min-microvolt = <1775000>;
-			regulator-max-microvolt = <2125000>;
-		};
-
-		pm8226_l26: l26 {
-			regulator-min-microvolt = <1225000>;
-			regulator-max-microvolt = <1300000>;
-		};
-
-		pm8226_l27: l27 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <1800000>;
-		};
-
-		pm8226_l28: l28 {
-			regulator-min-microvolt = <1800000>;
-			regulator-max-microvolt = <2950000>;
-		};
-
-		pm8226_lvs1: lvs1 {};
-	};
-};
-
-&sdhc_1 {
-	vmmc-supply = <&pm8226_l17>;
-	vqmmc-supply = <&pm8226_l6>;
-
-	bus-width = <8>;
-	non-removable;
-
-	status = "okay";
-};
-
-&sdhc_2 {
-	vmmc-supply = <&pm8226_l18>;
-	vqmmc-supply = <&pm8226_l21>;
-
-	bus-width = <4>;
-	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
-
-	status = "okay";
+&pm8226_l3 {
+	regulator-max-microvolt = <1337500>;
 };
 
-&tlmm {
-	accel_int_default_state: accel-int-default-state {
-		pins = "gpio54";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	backlight_i2c_default_state: backlight-i2c-default-state {
-		pins = "gpio20", "gpio21";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	backlight_pwm_default_state: backlight-pwm-default-state {
-		pins = "gpio33";
-		function = "gp0_clk";
-	};
-
-	muic_int_default_state: muic-int-default-state {
-		pins = "gpio67";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	tsp_en_default_state: tsp-en-default-state {
-		pins = "gpio31";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	tsp_en1_default_state: tsp-en1-default-state {
-		pins = "gpio73";
-		function = "gpio";
-		drive-strength = <2>;
-		bias-disable;
-	};
-
-	tsp_int_rst_default_state: tsp-int-rst-default-state {
-		pins = "gpio17";
-		function = "gpio";
-		drive-strength = <10>;
-		bias-pull-up;
-	};
+&pm8226_s4 {
+	regulator-max-microvolt = <1800000>;
 };
 
-&usb {
-	extcon = <&muic>, <&muic>;
-	status = "okay";
+&reg_tsp_3p3v {
+	gpio = <&tlmm 73 GPIO_ACTIVE_HIGH>;
 };
 
-&usb_hs_phy {
-	extcon = <&muic>;
-	v1p8-supply = <&pm8226_l10>;
-	v3p3-supply = <&pm8226_l20>;
+&tsp_en1_default_state {
+	pins = "gpio73";
 };
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
new file mode 100644
index 000000000000..11fec4e963b7
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
@@ -0,0 +1,474 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ * Copyright (c) 2023, Stefan Hansson <newbyte@postmarketos.org>
+ */
+
+#include <dt-bindings/input/input.h>
+#include "qcom-msm8226.dtsi"
+#include "qcom-pm8226.dtsi"
+
+/delete-node/ &adsp_region;
+/delete-node/ &smem_region;
+
+/ {
+	aliases {
+		mmc0 = &sdhc_1; /* SDC1 eMMC slot */
+		mmc1 = &sdhc_2; /* SDC2 SD card slot */
+		display0 = &framebuffer0;
+	};
+
+	chosen {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		stdout-path = "display0";
+
+		framebuffer0: framebuffer@3200000 {
+			compatible = "simple-framebuffer";
+			reg = <0x03200000 0x800000>;
+			width = <1280>;
+			height = <800>;
+			stride = <(1280 * 3)>;
+			format = "r8g8b8";
+		};
+	};
+
+	gpio-hall-sensor {
+		compatible = "gpio-keys";
+
+		event-hall-sensor {
+			label = "Hall Effect Sensor";
+			gpios = <&tlmm 110 GPIO_ACTIVE_LOW>;
+			linux,input-type = <EV_SW>;
+			linux,code = <SW_LID>;
+			debounce-interval = <15>;
+			linux,can-disable;
+			wakeup-source;
+		};
+	};
+
+	gpio-keys {
+		compatible = "gpio-keys";
+		autorepeat;
+
+		key-home {
+			label = "Home";
+			gpios = <&tlmm 108 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_HOMEPAGE>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-down {
+			label = "Volume Down";
+			gpios = <&tlmm 107 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEDOWN>;
+			debounce-interval = <15>;
+		};
+
+		key-volume-up {
+			label = "Volume Up";
+			gpios = <&tlmm 106 GPIO_ACTIVE_LOW>;
+			linux,code = <KEY_VOLUMEUP>;
+			debounce-interval = <15>;
+		};
+	};
+
+	i2c-backlight {
+		compatible = "i2c-gpio";
+		sda-gpios = <&tlmm 20 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+		scl-gpios = <&tlmm 21 (GPIO_ACTIVE_HIGH|GPIO_OPEN_DRAIN)>;
+
+		pinctrl-0 = <&backlight_i2c_default_state>;
+		pinctrl-names = "default";
+
+		i2c-gpio,delay-us = <4>;
+
+		#address-cells = <1>;
+		#size-cells = <0>;
+
+		backlight@2c {
+			compatible = "ti,lp8556";
+			reg = <0x2c>;
+
+			dev-ctrl = /bits/ 8 <0x80>;
+			init-brt = /bits/ 8 <0x3f>;
+
+			pwms = <&backlight_pwm 0 100000>;
+			pwm-names = "lp8556";
+
+			rom-a0h {
+				rom-addr = /bits/ 8 <0xa0>;
+				rom-val = /bits/ 8 <0x44>;
+			};
+
+			rom-a1h {
+				rom-addr = /bits/ 8 <0xa1>;
+				rom-val = /bits/ 8 <0x6c>;
+			};
+
+			rom-a5h {
+				rom-addr = /bits/ 8 <0xa5>;
+				rom-val = /bits/ 8 <0x24>;
+			};
+		};
+	};
+
+	backlight_pwm: pwm {
+		compatible = "clk-pwm";
+		#pwm-cells = <2>;
+		clocks = <&mmcc CAMSS_GP0_CLK>;
+		pinctrl-0 = <&backlight_pwm_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_1p8v: regulator-tsp-1p8v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_1p8v";
+		regulator-min-microvolt = <1800000>;
+		regulator-max-microvolt = <1800000>;
+
+		gpio = <&tlmm 31 GPIO_ACTIVE_HIGH>;
+		enable-active-high;
+
+		pinctrl-0 = <&tsp_en_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reg_tsp_3p3v: regulator-tsp-3p3v {
+		compatible = "regulator-fixed";
+		regulator-name = "tsp_3p3v";
+		regulator-min-microvolt = <3300000>;
+		regulator-max-microvolt = <3300000>;
+
+		/* GPIO is board-specific */
+		enable-active-high;
+
+		pinctrl-0 = <&tsp_en1_default_state>;
+		pinctrl-names = "default";
+	};
+
+	reserved-memory {
+		#address-cells = <1>;
+		#size-cells = <1>;
+		ranges;
+
+		framebuffer@3200000 {
+			reg = <0x03200000 0x800000>;
+			no-map;
+		};
+
+		mpss@8400000 {
+			reg = <0x08400000 0x1f00000>;
+			no-map;
+		};
+
+		mba@a300000 {
+			reg = <0x0a300000 0x100000>;
+			no-map;
+		};
+
+		reserved@cb00000 {
+			reg = <0x0cb00000 0x700000>;
+			no-map;
+		};
+
+		wcnss@d200000 {
+			reg = <0x0d200000 0x700000>;
+			no-map;
+		};
+
+		adsp_region: adsp@d900000 {
+			reg = <0x0d900000 0x1800000>;
+			no-map;
+		};
+
+		venus@f100000 {
+			reg = <0x0f100000 0x500000>;
+			no-map;
+		};
+
+		smem_region: smem@fa00000 {
+			reg = <0x0fa00000 0x100000>;
+			no-map;
+		};
+
+		reserved@fb00000 {
+			reg = <0x0fb00000 0x260000>;
+			no-map;
+		};
+
+		rfsa@fd60000 {
+			reg = <0x0fd60000 0x20000>;
+			no-map;
+		};
+
+		rmtfs@fd80000 {
+			compatible = "qcom,rmtfs-mem";
+			reg = <0x0fd80000 0x180000>;
+			no-map;
+
+			qcom,client-id = <1>;
+		};
+	};
+};
+
+&adsp {
+	status = "okay";
+};
+
+&blsp1_i2c4 {
+	status = "okay";
+
+	muic: usb-switch@25 {
+		compatible = "siliconmitus,sm5502-muic";
+		reg = <0x25>;
+
+		interrupt-parent = <&tlmm>;
+		interrupts = <67 IRQ_TYPE_EDGE_FALLING>;
+
+		pinctrl-0 = <&muic_int_default_state>;
+		pinctrl-names = "default";
+	};
+};
+
+&rpm_requests {
+	regulators {
+		compatible = "qcom,rpm-pm8226-regulators";
+
+		pm8226_s3: s3 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		/* Upper voltage constraint is board-specific */
+		pm8226_s4: s4 {
+			regulator-min-microvolt = <1800000>;
+		};
+
+		pm8226_s5: s5 {
+			regulator-min-microvolt = <1150000>;
+			regulator-max-microvolt = <1150000>;
+		};
+
+		pm8226_l1: l1 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1225000>;
+		};
+
+		pm8226_l2: l2 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		/* Upper voltage constraint is board-specific */
+		pm8226_l3: l3 {
+			regulator-min-microvolt = <750000>;
+			regulator-always-on;
+		};
+
+		pm8226_l4: l4 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l5: l5 {
+			regulator-min-microvolt = <1200000>;
+			regulator-max-microvolt = <1200000>;
+		};
+
+		pm8226_l6: l6 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l7: l7 {
+			regulator-min-microvolt = <1850000>;
+			regulator-max-microvolt = <1850000>;
+		};
+
+		pm8226_l8: l8 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+			regulator-always-on;
+		};
+
+		pm8226_l9: l9 {
+			regulator-min-microvolt = <2050000>;
+			regulator-max-microvolt = <2050000>;
+		};
+
+		pm8226_l10: l10 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l12: l12 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l14: l14 {
+			regulator-min-microvolt = <2750000>;
+			regulator-max-microvolt = <2750000>;
+		};
+
+		pm8226_l15: l15 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l16: l16 {
+			regulator-min-microvolt = <3000000>;
+			regulator-max-microvolt = <3350000>;
+		};
+
+		pm8226_l17: l17 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+
+			regulator-system-load = <200000>;
+			regulator-allow-set-load;
+			regulator-always-on;
+		};
+
+		pm8226_l18: l18 {
+			regulator-min-microvolt = <2950000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l19: l19 {
+			regulator-min-microvolt = <2850000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l20: l20 {
+			regulator-min-microvolt = <3075000>;
+			regulator-max-microvolt = <3075000>;
+		};
+
+		pm8226_l21: l21 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_l22: l22 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3000000>;
+		};
+
+		pm8226_l23: l23 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <3300000>;
+		};
+
+		pm8226_l24: l24 {
+			regulator-min-microvolt = <1300000>;
+			regulator-max-microvolt = <1350000>;
+		};
+
+		pm8226_l25: l25 {
+			regulator-min-microvolt = <1775000>;
+			regulator-max-microvolt = <2125000>;
+		};
+
+		pm8226_l26: l26 {
+			regulator-min-microvolt = <1225000>;
+			regulator-max-microvolt = <1300000>;
+		};
+
+		pm8226_l27: l27 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <1800000>;
+		};
+
+		pm8226_l28: l28 {
+			regulator-min-microvolt = <1800000>;
+			regulator-max-microvolt = <2950000>;
+		};
+
+		pm8226_lvs1: lvs1 {};
+	};
+};
+
+&sdhc_1 {
+	vmmc-supply = <&pm8226_l17>;
+	vqmmc-supply = <&pm8226_l6>;
+
+	bus-width = <8>;
+	non-removable;
+
+	status = "okay";
+};
+
+&sdhc_2 {
+	vmmc-supply = <&pm8226_l18>;
+	vqmmc-supply = <&pm8226_l21>;
+
+	bus-width = <4>;
+	cd-gpios = <&tlmm 38 GPIO_ACTIVE_LOW>;
+
+	status = "okay";
+};
+
+&tlmm {
+	accel_int_default_state: accel-int-default-state {
+		pins = "gpio54";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_i2c_default_state: backlight-i2c-default-state {
+		pins = "gpio20", "gpio21";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	backlight_pwm_default_state: backlight-pwm-default-state {
+		pins = "gpio33";
+		function = "gp0_clk";
+	};
+
+	muic_int_default_state: muic-int-default-state {
+		pins = "gpio67";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en_default_state: tsp-en-default-state {
+		pins = "gpio31";
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_en1_default_state: tsp-en1-default-state {
+		/* pins is board-specific */
+		function = "gpio";
+		drive-strength = <2>;
+		bias-disable;
+	};
+
+	tsp_int_rst_default_state: tsp-int-rst-default-state {
+		pins = "gpio17";
+		function = "gpio";
+		drive-strength = <10>;
+		bias-pull-up;
+	};
+};
+
+&usb {
+	extcon = <&muic>, <&muic>;
+	status = "okay";
+};
+
+&usb_hs_phy {
+	extcon = <&muic>;
+	v1p8-supply = <&pm8226_l10>;
+	v3p3-supply = <&pm8226_l20>;
+};
-- 
2.41.0

[PATCH v2 2/4] dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE

[Stefan Hansson]

This documents Samsung Galaxy Tab 4 10.1 LTE (samsung,matisselte)
which is a tablet by Samsung based on the MSM8926 SoC.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
---
 Documentation/devicetree/bindings/arm/qcom.yaml | 1 +
 1 file changed, 1 insertion(+)

diff --git a/Documentation/devicetree/bindings/arm/qcom.yaml b/Documentation/devicetree/bindings/arm/qcom.yaml
index 88b84035e7b1..242ffe89c6c6 100644
--- a/Documentation/devicetree/bindings/arm/qcom.yaml
+++ b/Documentation/devicetree/bindings/arm/qcom.yaml
@@ -196,6 +196,7 @@ properties:
           - enum:
               - microsoft,superman-lte
               - microsoft,tesla
+              - samsung,matisselte
           - const: qcom,msm8926
           - const: qcom,msm8226
 
-- 
2.41.0

[PATCH v2 3/4] ARM: dts: qcom: Add support for Samsung Galaxy Tab 4 10.1 LTE (SM-T535)

[Stefan Hansson]

Add a device tree for the Samsung Galaxy Tab 4 10.1 (SM-T535) LTE tablet
based on the MSM8926 platform.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
---
 arch/arm/boot/dts/qcom/Makefile               |  1 +
 .../qcom/qcom-msm8926-samsung-matisselte.dts  | 36 +++++++++++++++++++
 2 files changed, 37 insertions(+)
 create mode 100644 arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts

diff --git a/arch/arm/boot/dts/qcom/Makefile b/arch/arm/boot/dts/qcom/Makefile
index a3d293e40820..cab35eeb30f6 100644
--- a/arch/arm/boot/dts/qcom/Makefile
+++ b/arch/arm/boot/dts/qcom/Makefile
@@ -34,6 +34,7 @@ dtb-$(CONFIG_ARCH_QCOM) += \
 	qcom-msm8916-samsung-serranove.dtb \
 	qcom-msm8926-microsoft-superman-lte.dtb \
 	qcom-msm8926-microsoft-tesla.dtb \
+	qcom-msm8926-samsung-matisselte.dtb \
 	qcom-msm8960-cdp.dtb \
 	qcom-msm8960-samsung-expressatt.dtb \
 	qcom-msm8974-lge-nexus5-hammerhead.dtb \
diff --git a/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts b/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts
new file mode 100644
index 000000000000..6e25b1a74ce5
--- /dev/null
+++ b/arch/arm/boot/dts/qcom/qcom-msm8926-samsung-matisselte.dts
@@ -0,0 +1,36 @@
+// SPDX-License-Identifier: BSD-3-Clause
+/*
+ * Copyright (c) 2022, Matti Lehtimäki <matti.lehtimaki@gmail.com>
+ * Copyright (c) 2023, Stefan Hansson <newbyte@postmarketos.org>
+ */
+
+/dts-v1/;
+
+#include "qcom-msm8226-samsung-matisse-common.dtsi"
+
+/ {
+	model = "Samsung Galaxy Tab 4 10.1 LTE";
+	compatible = "samsung,matisselte", "qcom,msm8926", "qcom,msm8226";
+	chassis-type = "tablet";
+};
+
+&pm8226_l3 {
+	regulator-max-microvolt = <1350000>;
+};
+
+&pm8226_s4 {
+	regulator-max-microvolt = <2200000>;
+};
+
+&reg_tsp_3p3v {
+	gpio = <&tlmm 32 GPIO_ACTIVE_HIGH>;
+};
+
+&sdhc_2 {
+	/* SD card fails to probe with error -110 */
+	status = "disabled";
+};
+
+&tsp_en1_default_state {
+	pins = "gpio32";
+};
-- 
2.41.0

[PATCH v2 4/4] ARM: dts: qcom: samsung-matisse-common: Add UART

[Stefan Hansson]

This was not enabled in the matisse-wifi tree.

Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
---
 .../boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi    | 4 ++++
 1 file changed, 4 insertions(+)

diff --git a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
index 11fec4e963b7..35290ce63b40 100644
--- a/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
+++ b/arch/arm/boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi
@@ -233,6 +233,10 @@ muic: usb-switch@25 {
 	};
 };
 
+&blsp1_uart3 {
+	status = "okay";
+};
+
 &rpm_requests {
 	regulators {
 		compatible = "qcom,rpm-pm8226-regulators";
-- 
2.41.0

Re: [PATCH v2 1/4] ARM: dts: qcom: samsung-matisse-common: Add initial common device tree

[Krzysztof Kozlowski]

On 24/10/2023 22:33, Stefan Hansson wrote:
> According to the dts from the kernel source code released by Samsung,
> matissewifi and matisselte only have minor differences in hardware, so
> use a shared dtsi to reduce duplicated code. Additionally, this should
> make adding support for matisse3g easier should someone want to do that
> at a later point.
> 
> As such, add a common device tree for all matisse devices by Samsung
> based on the matissewifi dts. Support for matisselte will be introduced
> in a later patch in this series and will use the common dtsi as well.
> 
> Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
> ---
>  .../qcom-apq8026-samsung-matisse-wifi.dts     | 467 +----------------
>  .../qcom-msm8226-samsung-matisse-common.dtsi  | 474 ++++++++++++++++++
>  2 files changed, 483 insertions(+), 458 deletions(-)

It's impossible to review this change. Please use proper -B/-M/-C
arguments to format-patch to detect code move.

Best regards,
Krzysztof

Re: [PATCH v2 2/4] dt-bindings: arm: qcom: Add Samsung Galaxy Tab 4 10.1 LTE

[Krzysztof Kozlowski]

On 24/10/2023 22:33, Stefan Hansson wrote:
> This documents Samsung Galaxy Tab 4 10.1 LTE (samsung,matisselte)
> which is a tablet by Samsung based on the MSM8926 SoC.
> 
> Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
> ---
>  Documentation/devicetree/bindings/arm/qcom.yaml | 1 +

Reviewed-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>

Best regards,
Krzysztof

Re: [PATCH v2 4/4] ARM: dts: qcom: samsung-matisse-common: Add UART

[Krzysztof Kozlowski]

On 24/10/2023 22:33, Stefan Hansson wrote:
> This was not enabled in the matisse-wifi tree.

Your commit msg should explain why this should be enabled.

> 
> Signed-off-by: Stefan Hansson <newbyte@postmarketos.org>
> ---
>  .../boot/dts/qcom/qcom-msm8226-samsung-matisse-common.dtsi    | 4 ++++
>  1 file changed, 4 insertions(+)
> 

Best regards,
Krzysztof