mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
From: Can Guo <quic_cang@quicinc.com>
To: <neil.armstrong@linaro.org>, <mani@kernel.org>,
	<quic_nguyenb@quicinc.com>, <quic_nitirawa@quicinc.com>,
	<martin.petersen@oracle.com>
Cc: <linux-scsi@vger.kernel.org>, Andy Gross <agross@kernel.org>,
	"Bjorn Andersson" <andersson@kernel.org>,
	Konrad Dybcio <konrad.dybcio@linaro.org>,
	"James E.J. Bottomley" <jejb@linux.ibm.com>,
	"open list:UNIVERSAL FLASH STORAGE HOST CONTROLLER DRIVER..." 
	<linux-arm-msm@vger.kernel.org>,
	open list <linux-kernel@vger.kernel.org>
Subject: Re: [PATCH 2/6] scsi: ufs: ufs-qcom: Add support for UFS device version detection
Date: Tue, 31 Oct 2023 13:06:09 +0800	[thread overview]
Message-ID: <d5ffacca-579e-83c9-148e-1fd3b6ab5aad@quicinc.com> (raw)
In-Reply-To: <059cc112-7fb6-4da4-bc25-4eede0252f0e@linaro.org>

Hi Neil,

On 10/27/2023 8:51 PM, Neil Armstrong wrote:
> On 18/10/2023 16:02, Neil Armstrong wrote:
>> On 11/09/2023 07:59, Can Guo wrote:
>>> From: "Bao D. Nguyen" <quic_nguyenb@quicinc.com>
>>>
>>> Retrieve UFS device version from UFS host controller's spare register
>>> which is populated by bootloader, and use the UFS device version 
>>> together
>>> with host controller's HW version to decide the proper power modes 
>>> which
>>> should be used to configure the UFS PHY.
>>>
>>> Signed-off-by: Bao D. Nguyen <quic_nguyenb@quicinc.com>
>>> Signed-off-by: Can Guo <quic_cang@quicinc.com>
>>> ---
>>>   drivers/ufs/host/ufs-qcom.c | 30 +++++++++++++++++++++++-------
>>>   drivers/ufs/host/ufs-qcom.h |  2 ++
>>>   2 files changed, 25 insertions(+), 7 deletions(-)
>>>
>>> diff --git a/drivers/ufs/host/ufs-qcom.c b/drivers/ufs/host/ufs-qcom.c
>>> index 710f079..8a9d54f 100644
>>> --- a/drivers/ufs/host/ufs-qcom.c
>>> +++ b/drivers/ufs/host/ufs-qcom.c
>>> @@ -1030,7 +1030,7 @@ static void ufs_qcom_advertise_quirks(struct 
>>> ufs_hba *hba)
>>>                   | UFSHCD_QUIRK_BROKEN_PA_RXHSUNTERMCAP);
>>>       }
>>> -    if (host->hw_ver.major > 0x3)
>>> +    if (host->hw_ver.major > 0x3 && host->hw_ver.major < 0x5)
>>>           hba->quirks |= UFSHCD_QUIRK_REINIT_AFTER_MAX_GEAR_SWITCH;
>>>   }
>>> @@ -1038,11 +1038,33 @@ static void 
>>> ufs_qcom_set_pwr_mode_limits(struct ufs_hba *hba)
>>>   {
>>>       struct ufs_qcom_host *host = ufshcd_get_variant(hba);
>>>       struct ufs_dev_params *host_pwr_cap = &host->host_pwr_cap;
>>> +    u32 val, dev_major = 0;
>>>       ufshcd_init_pwr_dev_param(host_pwr_cap);
>>>       /* This driver only supports symmetic gear setting i.e., 
>>> hs_tx_gear == hs_rx_gear */
>>>       host_pwr_cap->hs_tx_gear = host_pwr_cap->hs_rx_gear = 
>>> ufs_qcom_get_hs_gear(hba);
>>> +    host->phy_gear = host_pwr_cap->hs_rx_gear;
>>> +
>>> +    if (host->hw_ver.major < 0x5) {
>>
>> Here you set G2 for < 0x5
>>
>>> +        /*
>>> +         * Power up the PHY using the minimum supported gear 
>>> (UFS_HS_G2).
>>> +         * Switching to max gear will be performed during reinit if 
>>> supported.
>>> +         */
>>> +        host->phy_gear = UFS_HS_G2;
>>> +    } else {
>>
>> So here is for >= 0x5
>>
>>> +        val = ufshcd_readl(host->hba, REG_UFS_DEBUG_SPARE_CFG);
>>> +        dev_major = FIELD_GET(GENMASK(7, 4), val);
>>> +
>>> +        if (host->hw_ver.major == 0x5 && (dev_major >= 0x4 ||
>>> +                          dev_major == 0)) {
>>> +            /* For UFS 4.0 and newer, or dev version is not 
>>> populated */
>>> +            host_pwr_cap->hs_rate = PA_HS_MODE_A;
>>> +        } else if (dev_major < 0x4 && dev_major > 0) {
>>> +            /* For UFS 3.1 and older, apply HS-G4 PHY settings to 
>>> save power */
>>> +            host->phy_gear = UFS_HS_G4;
>>> +        }
>>
>> But behavior of > 0x5 is not clear here, could you clarify it in v2 ?
>
> Now SM8650 is public, could you update it for v2 ?

For HWs whose hw_ver.major is > 0x5, say SM8650, initially phy_gear == 
host_pwr_cap->hs_rx_gear, which is HS_G5.

If a UFS3.x or older UFS device is connected, we overwrite phy_gear as 
HS_G4. I don't see an impact to SM8650.

Please let me know if I misunderstand anything here.


Thanks,

Can Guo.

>
> Thanks,
> Neil
>
>>
>> Thanks,
>> Neil
>

  parent reply	other threads:[~2023-10-31  5:06 UTC|newest]

Thread overview: 47+ messages / expand[flat|nested]  mbox.gz  Atom feed  top
     [not found] <1694411968-14413-1-git-send-email-quic_cang@quicinc.com>
2023-09-11  5:59 ` [PATCH 1/6] scsi: ufs: ufs-qcom: Setup host power mode during init Can Guo
2023-09-14 12:40   ` Nitin Rawat
2023-09-19 10:36   ` Manivannan Sadhasivam
2023-10-31 13:09     ` Can Guo
2023-09-11  5:59 ` [PATCH 2/6] scsi: ufs: ufs-qcom: Add support for UFS device version detection Can Guo
2023-09-11  9:17   ` Konrad Dybcio
2023-09-11  9:42     ` Can Guo
2023-09-11  9:46       ` Konrad Dybcio
2023-09-11 10:02         ` Can Guo
2023-09-15  2:31           ` Dmitry Baryshkov
2023-09-19 12:08             ` Manivannan Sadhasivam
2023-09-19 22:27               ` Dmitry Baryshkov
2023-09-20 10:23                 ` Manivannan Sadhasivam
2023-09-20 11:13                   ` Dmitry Baryshkov
2023-09-20 11:51                     ` Manivannan Sadhasivam
2023-10-18 12:47                   ` Manivannan Sadhasivam
2023-10-26 19:31                     ` Konrad Dybcio
2023-10-27 12:22                       ` Manivannan Sadhasivam
2023-09-15 12:48           ` Konrad Dybcio
2023-10-18 14:02   ` Neil Armstrong
     [not found]     ` <059cc112-7fb6-4da4-bc25-4eede0252f0e@linaro.org>
2023-10-31  5:06       ` Can Guo [this message]
2023-10-31  9:30         ` neil.armstrong
2023-09-11  5:59 ` [PATCH 3/6] phy: qualcomm: phy-qcom-qmp-ufs: Add High Speed Gear 5 support for SM8550 Can Guo
2023-09-14 12:26   ` Nitin Rawat
2023-09-15  2:07     ` Can Guo
2023-09-19 12:10   ` Manivannan Sadhasivam
2023-09-11  5:59 ` [PATCH 4/6] phy: qualcomm: phy-qcom-qmp-ufs: Move data structs and setting tables to header Can Guo
2023-09-14 11:44   ` Nitin Rawat
2023-09-14 12:28   ` Dmitry Baryshkov
2023-09-19 12:15     ` Manivannan Sadhasivam
2023-09-19 22:30       ` Dmitry Baryshkov
2023-09-20 10:19         ` Manivannan Sadhasivam
2023-09-21 14:02           ` Bjorn Andersson
2023-09-22 18:23             ` Manivannan Sadhasivam
2023-09-21 13:58       ` Bjorn Andersson
2023-09-11  5:59 ` [PATCH 5/6] scsi: ufs: ufs-sysfs: Expose UFS power info Can Guo
2023-09-14 11:33   ` Nitin Rawat
2023-09-15  1:59     ` Can Guo
2023-09-19 12:16   ` Manivannan Sadhasivam
2023-10-31  8:08     ` Can Guo
2023-10-26 19:53   ` Bart Van Assche
2023-10-31  4:46     ` Can Guo
2023-09-11  5:59 ` [PATCH 6/6] scsi: ufs: ufs-sysfs: Introduce UFS power info sysfs nodes Can Guo
2023-09-14 11:35   ` Nitin Rawat
2023-09-15  2:00     ` Can Guo
2023-09-18 15:36   ` Bart Van Assche
2023-10-31  4:53     ` Can Guo

Reply instructions:

You may reply publicly to this message via plain-text email
using any one of the following methods:

* Save the following mbox file, import it into your mail client,
  and reply-to-all from there: mbox

  Avoid top-posting and favor interleaved quoting:
  https://en.wikipedia.org/wiki/Posting_style#Interleaved_style

* Reply using the --to, --cc, and --in-reply-to
  switches of git-send-email(1):

  git send-email \
    --in-reply-to=d5ffacca-579e-83c9-148e-1fd3b6ab5aad@quicinc.com \
    --to=quic_cang@quicinc.com \
    --cc=agross@kernel.org \
    --cc=andersson@kernel.org \
    --cc=jejb@linux.ibm.com \
    --cc=konrad.dybcio@linaro.org \
    --cc=linux-arm-msm@vger.kernel.org \
    --cc=linux-kernel@vger.kernel.org \
    --cc=linux-scsi@vger.kernel.org \
    --cc=mani@kernel.org \
    --cc=martin.petersen@oracle.com \
    --cc=neil.armstrong@linaro.org \
    --cc=quic_nguyenb@quicinc.com \
    --cc=quic_nitirawa@quicinc.com \
    /path/to/YOUR_REPLY

  https://kernel.org/pub/software/scm/git/docs/git-send-email.html

* If your mail client supports setting the In-Reply-To header
  via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox

all inboxes | Powered by JetHome®