From: "Justin Mattock" <justinmattock@gmail.com>
To: "Linux Kernel Mailing List" <linux-kernel@vger.kernel.org>
Subject: audio: hda_intel azx_get_response timeout
Date: Sun, 15 Jun 2008 17:43:01 +0000 [thread overview]
Message-ID: <dd18b0c30806151043k46200e22lcaae79ad1f8209ed@mail.gmail.com> (raw)
[-- Attachment #1: Type: text/plain, Size: 434 bytes --]
I've noticed this([ 14.630815] hda_intel: azx_get_response timeout,
switching to polling mode: last cmd=0x00bf1c00
with 2.6.26-rc2 or 3, when connecting external speakers to listen to
music(keep in mind this was only once),
Now with kernel 2.6.26-rc5 and 6 I'm seeing this pop up every so
often,(seen this three times now). attached is dmesg of the message.
If I see anything else I'll send a post.
regards;
--
Justin P. Mattock
[-- Attachment #2: hda_intel --]
[-- Type: application/octet-stream, Size: 39740 bytes --]
[ 0.000000] Linux version 2.6.26-rc6-00079-g37a0cb0 (root@unix) (gcc version 4.2.3 (Debian 4.2.3-3)) #4 SMP Sun Jun 15 05:21:05 UTC 2008
[ 0.000000] BIOS-provided physical RAM map:
[ 0.000000] BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[ 0.000000] BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[ 0.000000] BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[ 0.000000] BIOS-e820: 0000000000100000 - 000000003f0ea000 (usable)
[ 0.000000] BIOS-e820: 000000003f0ea000 - 000000003f2eb000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003f2eb000 - 000000003febe000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003febe000 - 000000003feef000 (ACPI NVS)
[ 0.000000] BIOS-e820: 000000003feef000 - 000000003ff00000 (ACPI data)
[ 0.000000] BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
[ 0.000000] BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[ 0.000000] BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[ 0.000000] BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[ 0.000000] BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[ 0.000000] BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[ 0.000000] 112MB HIGHMEM available.
[ 0.000000] 896MB LOWMEM available.
[ 0.000000] Entering add_active_range(0, 0, 258282) 0 entries of 256 used
[ 0.000000] Zone PFN ranges:
[ 0.000000] DMA 0 -> 4096
[ 0.000000] Normal 4096 -> 229376
[ 0.000000] HighMem 229376 -> 258282
[ 0.000000] Movable zone start PFN for each node
[ 0.000000] early_node_map[1] active PFN ranges
[ 0.000000] 0: 0 -> 258282
[ 0.000000] On node 0 totalpages: 258282
[ 0.000000] DMA zone: 32 pages used for memmap
[ 0.000000] DMA zone: 0 pages reserved
[ 0.000000] DMA zone: 4064 pages, LIFO batch:0
[ 0.000000] Normal zone: 1760 pages used for memmap
[ 0.000000] Normal zone: 223520 pages, LIFO batch:31
[ 0.000000] HighMem zone: 226 pages used for memmap
[ 0.000000] HighMem zone: 28680 pages, LIFO batch:7
[ 0.000000] Movable zone: 0 pages used for memmap
[ 0.000000] DMI 2.4 present.
[ 0.000000] Using APIC driver default
[ 0.000000] ACPI: RSDP 000FE020, 0024 (r2 APPLE )
[ 0.000000] ACPI: XSDT 3FEFD1C0, 0074 (r1 APPLE Apple00 A5 1000013)
[ 0.000000] ACPI: FACP 3FEFB000, 00F4 (r3 APPLE Apple00 A5 Loki 5F)
[ 0.000000] ACPI: DSDT 3FEF0000, 48D1 (r1 APPLE MacBookP 20002 INTL 20050309)
[ 0.000000] ACPI: FACS 3FEC0000, 0040
[ 0.000000] ACPI: HPET 3FEFA000, 0038 (r1 APPLE Apple00 1 Loki 5F)
[ 0.000000] ACPI: APIC 3FEF9000, 0068 (r1 APPLE Apple00 1 Loki 5F)
[ 0.000000] ACPI: MCFG 3FEF8000, 003C (r1 APPLE Apple00 1 Loki 5F)
[ 0.000000] ACPI: ASF! 3FEF7000, 00A0 (r32 APPLE Apple00 1 Loki 5F)
[ 0.000000] ACPI: SBST 3FEF6000, 0030 (r1 APPLE Apple00 1 Loki 5F)
[ 0.000000] ACPI: ECDT 3FEF5000, 0053 (r1 APPLE Apple00 1 Loki 5F)
[ 0.000000] ACPI: SSDT 3FEEF000, 04DC (r1 APPLE CpuPm 3000 INTL 20050309)
[ 0.000000] ACPI: SSDT 3FEBD000, 064F (r1 SataRe SataPri 1000 INTL 20050309)
[ 0.000000] ACPI: SSDT 3FEBC000, 069C (r1 SataRe SataSec 1000 INTL 20050309)
[ 0.000000] ACPI: DMI detected: Apple
[ 0.000000] ACPI: PM-Timer IO Port: 0x408
[ 0.000000] ACPI: Local APIC address 0xfee00000
[ 0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[ 0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[ 0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[ 0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[ 0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[ 0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[ 0.000000] ACPI: IRQ0 used by override.
[ 0.000000] ACPI: IRQ2 used by override.
[ 0.000000] ACPI: IRQ9 used by override.
[ 0.000000] Enabling APIC mode: Flat. Using 1 I/O APICs
[ 0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[ 0.000000] Using ACPI (MADT) for SMP configuration information
[ 0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000)
[ 0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[ 0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[ 0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[ 0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[ 0.000000] PERCPU: Allocating 46760 bytes of per cpu data
[ 0.000000] NR_CPUS: 2, nr_cpu_ids: 2
[ 0.000000] Built 1 zonelists in Zone order, mobility grouping on. Total pages: 256264
[ 0.000000] Kernel command line: root=/dev/sda1 ro quiet splash vga=773 selinux=1 audit=1 enforcing=1 debug acpi_osi=Linux pnpacpi=off pci=routeirq usbcore.autosuspend=1 nmi_watchdog=0
[ 0.000000] audit: enabled (after initialization)
[ 0.000000] ACPI: Added _OSI(Linux)
[ 0.000000] mapped APIC to ffffb000 (fee00000)
[ 0.000000] mapped IOAPIC to ffffa000 (fec00000)
[ 0.000000] Enabling fast FPU save and restore... done.
[ 0.000000] Enabling unmasked SIMD FPU exception support... done.
[ 0.000000] Initializing CPU#0
[ 0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[ 0.000000] Extended CMOS year: 2000
[ 0.000000] Detected 2161.324 MHz processor.
[ 0.010000] Console: colour dummy device 80x25
[ 0.010000] console [tty0] enabled
[ 0.010000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[ 0.010000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[ 0.010000] Memory: 1018628k/1033128k available (2582k kernel code, 13884k reserved, 1332k data, 332k init, 115624k highmem)
[ 0.010000] virtual kernel memory layout:
[ 0.010000] fixmap : 0xfff7e000 - 0xfffff000 ( 516 kB)
[ 0.010000] pkmap : 0xff800000 - 0xffc00000 (4096 kB)
[ 0.010000] vmalloc : 0xf8800000 - 0xff7fe000 ( 111 MB)
[ 0.010000] lowmem : 0xc0000000 - 0xf8000000 ( 896 MB)
[ 0.010000] .init : 0xc04d9000 - 0xc052c000 ( 332 kB)
[ 0.010000] .data : 0xc0385a69 - 0xc04d2dac (1332 kB)
[ 0.010000] .text : 0xc0100000 - 0xc0385a69 (2582 kB)
[ 0.010000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[ 0.010000] CPA: page pool initialized 1 of 1 pages preallocated
[ 0.010000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[ 0.010000] hpet clockevent registered
[ 0.159749] Calibrating delay using timer specific routine.. 4326.66 BogoMIPS (lpj=21633313)
[ 0.159797] Security Framework initialized
[ 0.159803] SELinux: Initializing.
[ 0.159816] SELinux: Starting in enforcing mode
[ 0.159822] selinux_register_security: Registering secondary module capability
[ 0.159827] Capability LSM initialized as secondary
[ 0.159850] Mount-cache hash table entries: 512
[ 0.160000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.160000] CPU: L2 cache: 4096K
[ 0.160000] CPU: Physical Processor ID: 0
[ 0.160000] CPU: Processor Core ID: 0
[ 0.160000] Intel machine check architecture supported.
[ 0.160000] Intel machine check reporting enabled on CPU#0.
[ 0.160000] using mwait in idle threads.
[ 0.160000] Checking 'hlt' instruction... OK.
[ 0.200000] ACPI: Core revision 20080321
[ 0.210000] ENABLING IO-APIC IRQs
[ 0.210000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[ 0.309939] CPU0: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06
[ 0.310000] Booting processor 1/1 ip 6000
[ 0.320000] Initializing CPU#1
[ 0.320000] Calibrating delay using timer specific routine.. 4322.52 BogoMIPS (lpj=21612614)
[ 0.320000] CPU: L1 I cache: 32K, L1 D cache: 32K
[ 0.320000] CPU: L2 cache: 4096K
[ 0.320000] CPU: Physical Processor ID: 0
[ 0.320000] CPU: Processor Core ID: 1
[ 0.320000] Intel machine check architecture supported.
[ 0.320000] Intel machine check reporting enabled on CPU#1.
[ 0.470000] CPU1: Intel(R) Core(TM)2 CPU T7400 @ 2.16GHz stepping 06
[ 0.470000] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[ 0.470031] Brought up 2 CPUs
[ 0.470037] Total of 2 processors activated (8649.18 BogoMIPS).
[ 0.470060] CPU0 attaching sched-domain:
[ 0.470065] domain 0: span 0-1
[ 0.470068] groups: 0 1
[ 0.470076] CPU1 attaching sched-domain:
[ 0.470081] domain 0: span 0-1
[ 0.470084] groups: 1 0
[ 0.480000] net_namespace: 516 bytes
[ 0.480000] Booting paravirtualized kernel on bare hardware
[ 0.480000] NET: Registered protocol family 16
[ 0.480000] No dock devices found.
[ 0.480000] EISA bus registered
[ 0.480000] ACPI: bus type pci registered
[ 0.480000] PCI: Using configuration type 1 for base access
[ 0.480000] Setting up standard PCI resources
[ 0.480000] ACPI: EC: EC description table is found, configuring boot EC
[ 0.480000] ACPI: EC: non-query interrupt received, switching to interrupt mode
[ 0.497474] ACPI: BIOS _OSI(Linux) query honored via cmdline
[ 0.498330] ACPI: Interpreter enabled
[ 0.498335] ACPI: (supports S0 S3 S4 S5)
[ 0.498394] ACPI: Using IOAPIC for interrupt routing
[ 0.524110] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[ 0.524116] ACPI: EC: driver started in interrupt mode
[ 0.524921] ACPI: PCI Root Bridge [PCI0] (0000:00)
[ 0.526621] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[ 0.526630] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
[ 0.527620] PCI: Transparent bridge - 0000:00:1e.0
[ 0.527672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[ 0.529219] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[ 0.529702] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[ 0.530000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[ 0.530000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[ 0.530000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[ 0.550000] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.550000] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.550000] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[ 0.550000] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[ 0.550000] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[ 0.550000] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[ 0.550000] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[ 0.550000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15)
[ 0.550000] Linux Plug and Play Support v0.97 (c) Adam Belay
[ 0.550000] pnp: PnP ACPI: disabled
[ 0.550000] SCSI subsystem initialized
[ 0.550000] libata version 3.00 loaded.
[ 0.560000] usbcore: registered new interface driver usbfs
[ 0.560000] usbcore: registered new interface driver hub
[ 0.560000] usbcore: registered new device driver usb
[ 0.560000] PCI: Using ACPI for IRQ routing
[ 0.560000] PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
[ 0.560000] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.560000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.560000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 0.560000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.560000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.560000] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 0.560000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 0.560000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 0.560000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 0.560000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 0.560000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 0.560000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 0.560000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 0.560000] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
[ 0.560000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.560000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.560000] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.560000] ACPI: PCI Interrupt 0000:0c:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 0.589877] NetLabel: Initializing
[ 0.589882] NetLabel: domain hash size = 128
[ 0.589885] NetLabel: protocols = UNLABELED CIPSOv4
[ 0.589953] NetLabel: unlabeled traffic allowed by default
[ 0.589964] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[ 0.589971] hpet0: 3 64-bit timers, 14318180 Hz
[ 0.598804] Switched to high resolution mode on CPU 0
[ 0.600749] Switched to high resolution mode on CPU 1
[ 0.633759] PCI: Bridge: 0000:00:01.0
[ 0.633764] IO window: 3000-3fff
[ 0.633770] MEM window: 0x50300000-0x503fffff
[ 0.633775] PREFETCH window: 0x0000000040000000-0x0000000047ffffff
[ 0.633783] PCI: Bridge: 0000:00:1c.0
[ 0.633788] IO window: 2000-2fff
[ 0.633796] MEM window: 0x50200000-0x502fffff
[ 0.633802] PREFETCH window: 0x0000000050500000-0x00000000505fffff
[ 0.633813] PCI: Bridge: 0000:00:1c.1
[ 0.633816] IO window: disabled.
[ 0.633823] MEM window: 0x50100000-0x501fffff
[ 0.633830] PREFETCH window: disabled.
[ 0.633839] PCI: Bridge: 0000:00:1c.2
[ 0.633843] IO window: 1000-1fff
[ 0.633851] MEM window: 0x4c100000-0x500fffff
[ 0.633857] PREFETCH window: 0x0000000048000000-0x000000004bffffff
[ 0.633867] PCI: Bridge: 0000:00:1e.0
[ 0.633871] IO window: disabled.
[ 0.633878] MEM window: 0x4c000000-0x4c0fffff
[ 0.633884] PREFETCH window: disabled.
[ 0.633904] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 0.633913] PCI: Setting latency timer of device 0000:00:01.0 to 64
[ 0.633939] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 0.633948] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[ 0.633976] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[ 0.633985] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[ 0.634012] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 0.634022] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[ 0.634038] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[ 0.634055] NET: Registered protocol family 2
[ 0.662568] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[ 0.662848] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[ 0.663270] TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
[ 0.663828] TCP: Hash tables configured (established 131072 bind 65536)
[ 0.663833] TCP reno registered
[ 0.672628] NET: Registered protocol family 1
[ 0.682502] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[ 0.692497] Initializing RT-Tester: OK
[ 0.692497] audit: initializing netlink socket (enabled)
[ 0.692497] type=2000 audit(1213507617.670:1): initialized
[ 0.692498] highmem bounce pool size: 64 pages
[ 0.692498] Total HugeTLB memory allocated, 0
[ 0.703848] fuse init (API version 7.9)
[ 0.704375] msgmni has been set to 1764
[ 0.704591] SELinux: Registering netfilter hooks
[ 0.704800] io scheduler noop registered
[ 0.705085] io scheduler cfq registered (default)
[ 0.705219] pci 0000:01:00.0: Boot video device
[ 0.705621] vesafb: framebuffer at 0x40000000, mapped to 0xf8880000, using 1536k, total 16384k
[ 0.705629] vesafb: mode is 1024x768x8, linelength=1024, pages=18
[ 0.705633] vesafb: protected mode interface info at c000:ad0c
[ 0.705638] vesafb: pmi: set display start = c00cad94, set palette = c00cae50
[ 0.705642] vesafb: scrolling: redraw
[ 0.705646] vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
[ 0.718884] Console: switching to colour frame buffer device 128x48
[ 0.731026] fb0: VESA VGA frame buffer device
[ 0.731303] power_supply ADP1: uevent
[ 0.731394] power_supply ADP1: No power supply yet
[ 0.732498] power_supply ADP1: power_supply_changed
[ 0.732498] ACPI: AC Adapter [ADP1] (on-line)
[ 0.732498] power_supply ADP1: power_supply_changed_work
[ 0.732498] power_supply ADP1: power_supply_update_gen_leds 1
[ 0.732498] power_supply ADP1: uevent
[ 0.732498] power_supply ADP1: POWER_SUPPLY_NAME=ADP1
[ 0.732498] power_supply ADP1: Static prop TYPE=Mains
[ 0.732624] power_supply ADP1: 1 dynamic props
[ 0.732733] power_supply ADP1: prop ONLINE=1
[ 0.857865] power_supply BAT0: uevent
[ 0.857865] power_supply BAT0: No power supply yet
[ 0.857865] power_supply BAT0: power_supply_changed
[ 0.857865] power_supply BAT0: power_supply_changed_work
[ 0.920336] ACPI: Battery Slot [BAT0] (battery present)
[ 0.937835] hpet_resources: 0xfed00000 is busy
[ 0.940341] loop: module loaded
[ 0.944031] Linux video capture interface: v2.00
[ 0.954020] input: Macintosh mouse button emulation as /class/input/input0
[ 0.963166] Driver 'sd' needs updating - please use bus_type methods
[ 0.963166] Driver 'sr' needs updating - please use bus_type methods
[ 0.965506] power_supply BAT0: power_supply_update_bat_leds 4
[ 0.965521] power_supply BAT0: uevent
[ 0.965522] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[ 0.965527] power_supply BAT0: Static prop TYPE=Battery
[ 0.965531] power_supply BAT0: 12 dynamic props
[ 0.965533] power_supply BAT0: prop STATUS=Full
[ 0.965537] power_supply BAT0: prop PRESENT=1
[ 0.965541] power_supply BAT0: prop TECHNOLOGY=Unknown
[ 0.965545] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=10800000
[ 0.965548] power_supply BAT0: prop VOLTAGE_NOW=12548000
[ 0.965551] power_supply BAT0: prop CURRENT_NOW=0
[ 0.965554] power_supply BAT0: prop ENERGY_FULL_DESIGN=55000000
[ 0.965557] power_supply BAT0: prop ENERGY_FULL=53040000
[ 0.965560] power_supply BAT0: prop ENERGY_NOW=52740000
[ 0.965563] power_supply BAT0: prop MODEL_NAME=ASMB012
[ 0.965566] power_supply BAT0: prop MANUFACTURER=SMPN012
[ 0.965569] power_supply BAT0: prop SERIAL_NUMBER=
[ 1.027297] ata_piix 0000:00:1f.1: version 2.12
[ 1.028324] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[ 1.031325] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[ 1.031536] scsi0 : ata_piix
[ 1.040471] scsi1 : ata_piix
[ 1.040471] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x40b0 irq 14
[ 1.046852] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x40b8 irq 15
[ 1.223558] ata1.00: ATAPI: MATSHITADVD-R UJ-857D, KCV9, max UDMA/66
[ 1.263497] ata1.00: configured for UDMA/66
[ 1.263497] scsi 0:0:0:0: CD-ROM MATSHITA DVD-R UJ-857D KCV9 PQ: 0 ANSI: 5
[ 1.444448] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[ 1.447689] Uniform CD-ROM driver Revision: 3.20
[ 1.452978] sr 0:0:0:0: Attached scsi CD-ROM sr0
[ 1.463315] sr 0:0:0:0: Attached scsi generic sg0 type 5
[ 1.463315] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[ 1.463315] ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ]
[ 1.612993] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[ 1.622978] scsi2 : ata_piix
[ 1.622978] scsi3 : ata_piix
[ 1.633864] ata3: SATA max UDMA/133 cmd 0x40c8 ctl 0x40e4 bmdma 0x40a0 irq 19
[ 1.633864] ata4: SATA max UDMA/133 cmd 0x40c0 ctl 0x40e0 bmdma 0x40a8 irq 19
[ 1.814737] ata3.01: ATA-8: FUJITSU MHW2120BH, 00810013, max UDMA/100
[ 1.818330] ata3.01: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
[ 1.853483] ata3.01: configured for UDMA/100
[ 2.024587] scsi 2:0:1:0: Direct-Access ATA FUJITSU MHW2120B 0081 PQ: 0 ANSI: 5
[ 2.024587] sd 2:0:1:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 2.024587] sd 2:0:1:0: [sda] Write Protect is off
[ 2.041888] sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.045607] sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.049554] sd 2:0:1:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[ 2.059478] sd 2:0:1:0: [sda] Write Protect is off
[ 2.059478] sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00
[ 2.061385] sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[ 2.071344] sda: sda1 sda2 < sda5 >
[ 2.080068] sd 2:0:1:0: [sda] Attached SCSI disk
[ 2.084255] sd 2:0:1:0: Attached scsi generic sg1 type 0
[ 2.087587] usbcore: registered new interface driver usblcd
[ 2.087587] usbcore: registered new interface driver usbled
[ 2.087587] PNP: No PS/2 controller found. Probing ports directly.
[ 2.105787] i8042.c: No controller found.
[ 2.131598] mice: PS/2 mouse device common for all mice
[ 2.131599] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[ 2.131599] EDAC MC: Ver: 2.1.0 Jun 14 2008
[ 2.158697] cpuidle: using governor ladder
[ 2.158697] cpuidle: using governor menu
[ 2.165668] usbcore: registered new interface driver hiddev
[ 2.167994] usbcore: registered new interface driver usbhid
[ 2.172396] usbhid: v2.6:USB HID core driver
[ 2.176982] Advanced Linux Sound Architecture Driver Version 1.0.16.
[ 2.176984] ALSA device list:
[ 2.185955] No soundcards found.
[ 2.194712] oprofile: using NMI interrupt.
[ 2.194712] IPVS: Registered protocols (TCP, AH, ESP)
[ 2.194712] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[ 2.207283] IPVS: ipvs loaded.
[ 2.211555] Initializing XFRM netlink socket
[ 2.217251] NET: Registered protocol family 17
[ 2.221542] NET: Registered protocol family 15
[ 2.225726] Using IPI No-Shortcut mode
[ 2.234708] kjournald starting. Commit interval 5 seconds
[ 2.234378] EXT3-fs: mounted filesystem with ordered data mode.
[ 2.234378] VFS: Mounted root (ext3 filesystem) readonly.
[ 2.234378] Freeing unused kernel memory: 332k freed
[ 2.937411] SELinux: 8192 avtab hash slots, 205781 rules.
[ 3.072470] SELinux: 8192 avtab hash slots, 205781 rules.
[ 3.252471] SELinux: 7 users, 7 roles, 3017 types, 90 bools
[ 3.256656] SELinux: 72 classes, 205781 rules
[ 3.273059] SELinux: Completing initialization.
[ 3.273678] SELinux: Setting up existing superblocks.
[ 3.305296] SELinux: initialized (dev sda1, type ext3), uses xattr
[ 3.305296] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[ 3.305296] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
[ 3.305296] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
[ 3.426680] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[ 3.430718] SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
[ 3.434707] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 3.444703] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
[ 3.444703] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[ 3.452529] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[ 3.456689] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[ 3.460592] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[ 3.468875] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
[ 3.468875] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[ 3.472833] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[ 3.517454] SELinux: policy loaded with handle_unknown=deny
[ 3.517454] type=1403 audit(1213507620.372:2): policy loaded auid=4294967295 ses=4294967295
[ 4.628407] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 4.643041] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 10.276431] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 10.514353] power_supply ADP1: uevent
[ 10.523072] power_supply ADP1: POWER_SUPPLY_NAME=ADP1
[ 10.527458] power_supply ADP1: Static prop TYPE=Mains
[ 10.533024] power_supply ADP1: 1 dynamic props
[ 10.541753] power_supply ADP1: prop ONLINE=1
[ 10.546189] power_supply BAT0: uevent
[ 10.550393] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[ 10.551084] power_supply BAT0: Static prop TYPE=Battery
[ 10.560232] power_supply BAT0: 12 dynamic props
[ 10.713907] power_supply BAT0: prop STATUS=Full
[ 10.719157] power_supply BAT0: prop PRESENT=1
[ 10.723231] power_supply BAT0: prop TECHNOLOGY=Unknown
[ 10.729143] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=10800000
[ 10.731323] power_supply BAT0: prop VOLTAGE_NOW=12548000
[ 10.738325] power_supply BAT0: prop CURRENT_NOW=0
[ 10.742261] power_supply BAT0: prop ENERGY_FULL_DESIGN=55000000
[ 10.746180] power_supply BAT0: prop ENERGY_FULL=53040000
[ 10.751277] power_supply BAT0: prop ENERGY_NOW=52740000
[ 10.751336] power_supply BAT0: prop MODEL_NAME=ASMB012
[ 10.755118] power_supply BAT0: prop MANUFACTURER=SMPN012
[ 10.758834] power_supply BAT0: prop SERIAL_NUMBER=
[ 11.830610] ACPI: SSDT 3FEB8C10, 02AE (r1 APPLE Cpu0Ist 3000 INTL 20050309)
[ 11.834357] ACPI: SSDT 3FEB8910, 02A0 (r1 APPLE Cpu0Cst 3001 INTL 20050309)
[ 11.834357] Monitor-Mwait will be used to enter C-1 state
[ 11.840024] Monitor-Mwait will be used to enter C-2 state
[ 11.843579] Monitor-Mwait will be used to enter C-3 state
[ 11.849342] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[ 11.852890] ACPI: ACPI0007:00 is registered as cooling_device0
[ 11.856356] ACPI: Processor [CPU0] (supports 8 throttling states)
[ 11.865405] ACPI: SSDT 3FEB8F10, 0087 (r1 APPLE Cpu1Ist 3000 INTL 20050309)
[ 11.867135] ACPI: SSDT 3FEB7F10, 0085 (r1 APPLE Cpu1Cst 3000 INTL 20050309)
[ 11.875379] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[ 11.878816] ACPI: ACPI0007:01 is registered as cooling_device1
[ 11.878816] Marking TSC unstable due to: TSC halts in idle.
[ 11.888844] ACPI: Processor [CPU1] (supports 8 throttling states)
[ 11.905383] input: Power Button (FF) as /class/input/input1
[ 11.953066] ACPI: Power Button (FF) [PWRF]
[ 11.956782] input: Lid Switch as /class/input/input2
[ 11.960488] ACPI: Lid Switch [LID0]
[ 11.963940] input: Power Button (CM) as /class/input/input3
[ 12.012806] ACPI: Power Button (CM) [PWRB]
[ 12.016247] input: Sleep Button (CM) as /class/input/input4
[ 12.068613] ACPI: Sleep Button (CM) [SLPB]
[ 12.078279] input: Video Bus as /class/input/input5
[ 12.153804] ACPI: Video Device [GFX0] (multi-head: yes rom: no post: no)
[ 12.221140] USB Universal Host Controller Interface driver v3.0
[ 12.225047] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[ 12.231147] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[ 12.233507] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[ 12.237864] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[ 12.242040] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[ 12.246261] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
[ 12.250656] usb usb1: configuration #1 chosen from 1 choice
[ 12.254096] hub 1-0:1.0: USB hub found
[ 12.261019] hub 1-0:1.0: 2 ports detected
[ 12.291221] ath_hal: module license 'Proprietary' taints kernel.
[ 12.296694] ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
[ 12.368315] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[ 12.372901] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[ 12.376695] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[ 12.382276] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[ 12.387153] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
[ 12.392464] usb usb2: configuration #1 chosen from 1 choice
[ 12.397328] hub 2-0:1.0: USB hub found
[ 12.402228] hub 2-0:1.0: 2 ports detected
[ 12.508472] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[ 12.513401] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[ 12.518174] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[ 12.523225] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[ 12.528463] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
[ 12.533603] usb usb3: configuration #1 chosen from 1 choice
[ 12.538647] hub 3-0:1.0: USB hub found
[ 12.543516] hub 3-0:1.0: 2 ports detected
[ 12.594926] wlan: svn r3692
[ 12.655252] usb 1-2: new full speed USB device using uhci_hcd and address 2
[ 12.667947] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[ 12.667947] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[ 12.668567] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[ 12.677946] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[ 12.686190] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
[ 12.691372] usb usb4: configuration #1 chosen from 1 choice
[ 12.696473] hub 4-0:1.0: USB hub found
[ 12.702624] hub 4-0:1.0: 2 ports detected
[ 12.829659] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[ 12.836355] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[ 12.841381] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[ 12.848603] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[ 12.859319] ehci_hcd 0000:00:1d.7: debug port 1
[ 12.859319] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[ 12.864245] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x50405400
[ 12.895706] usb 1-2: configuration #1 chosen from 1 choice
[ 12.895722] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[ 12.895856] usb usb5: configuration #1 chosen from 1 choice
[ 12.895925] hub 5-0:1.0: USB hub found
[ 12.895936] hub 5-0:1.0: 8 ports detected
[ 12.937398] usb 1-2: can't set config #1, error -71
[ 12.967882] ath_pci: svn r3692
[ 13.028570] ACPI: PCI Interrupt 0000:0c:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[ 13.086777] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19] MMIO=[4c004000-4c0047ff] Max Packet=[4096] IR/IT contexts=[4/8]
[ 13.107571] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[ 13.107571] PCI: Setting latency timer of device 0000:03:00.0 to 64
[ 13.247640] MadWifi: ath_attach: HAL managed transmit power control (TPC) disabled.
[ 13.247640] MadWifi: ath_attach: Interference mitigation is supported. Currently disabled.
[ 13.257527] MadWifi: ath_attach: Switching rfkill capability off.
[ 13.306872] usb 1-2: USB disconnect, address 2
[ 13.363241] ath_rate_sample: 1.2 (svn r3692)
[ 13.371205] wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.371205] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[ 13.372476] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.378678] wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.384303] wifi0: turboG rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[ 13.389624] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[ 13.398729] wifi0: Atheros AR5418 chip found (MAC 12.10, PHY SChip 8.1, Radio 12.0)
[ 13.404082] wifi0: Use hw queue 1 for WME_AC_BE traffic
[ 13.409450] wifi0: Use hw queue 0 for WME_AC_BK traffic
[ 13.414718] wifi0: Use hw queue 2 for WME_AC_VI traffic
[ 13.429455] wifi0: Use hw queue 3 for WME_AC_VO traffic
[ 13.429953] wifi0: Use hw queue 4 for XR traffic
[ 13.434774] wifi0: Use hw queue 7 for UAPSD traffic
[ 13.439604] wifi0: Use hw queue 8 for CAB traffic
[ 13.444939] wifi0: Use hw queue 9 for beacons
[ 13.526135] ath_pci: wifi0: Atheros 5418: mem=0x50100000, irq=17
[ 13.530685] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[ 13.531868] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[ 13.615526] hda_codec: STAC922x, Apple subsys_id=106b1e00
[ 14.205555] usb 5-4: new high speed USB device using ehci_hcd and address 3
[ 14.364967] usb 5-4: configuration #1 chosen from 1 choice
[ 14.450815] ieee1394: Host added: ID:BUS[0-00:1023] GUID[0019e3fffe2ad87e]
[ 14.630815] hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x00bf1c00
[ 14.994484] Clocksource tsc unstable (delta = -313768306 ns)
[ 15.220838] usb 1-2: new full speed USB device using uhci_hcd and address 3
[ 15.415624] usb 1-2: configuration #1 chosen from 1 choice
[ 15.432925] input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input6
[ 15.466406] input: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2
[ 15.478891] input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input7
[ 15.495817] input: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2
[ 15.777185] usb 3-2: new full speed USB device using uhci_hcd and address 2
[ 15.961843] usb 3-2: configuration #1 chosen from 1 choice
[ 15.976903] hiddev0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-2
[ 16.263427] usb 4-1: new full speed USB device using uhci_hcd and address 2
[ 16.468403] usb 4-1: configuration #1 chosen from 1 choice
[ 16.506102] input: HID 05ac:1000 as /class/input/input8
[ 16.519580] input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1d.3-1
[ 16.548703] input: HID 05ac:1000 as /class/input/input9
[ 16.558611] input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1d.3-1
[ 16.667223] uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:8501)
[ 16.674956] uvcvideo: Failed to query (135) UVC control 1 (unit 0) : -32 (exp. 26).
[ 16.687221] input: Built-in iSight as /class/input/input10
[ 16.739247] usbcore: registered new interface driver uvcvideo
[ 16.744342] USB Video Class driver (SVN r212)
[ 16.767009] appletouch: Geyser mode initialized.
[ 16.776007] input: appletouch as /class/input/input11
[ 16.903945] usbcore: registered new interface driver appletouch
[ 17.291060] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[ 17.382056] applesmc: Apple MacBook Pro detected:
[ 17.389438] applesmc: - Model with accelerometer
[ 17.400206] applesmc: - Model with light sensors and backlight
[ 17.400208] applesmc: - Model with 12 temperature sensors
[ 17.407743] applesmc: device has already been initialized (0xe0, 0x00).
[ 17.407745] applesmc: device successfully initialized.
[ 17.408204] applesmc: 2 fans found.
[ 17.408930] input: applesmc as /class/input/input12
[ 17.472313] Registered led device: smc::kbd_backlight
[ 17.472313] applesmc: driver successfully loaded.
[ 17.536222] Linux agpgart interface v0.103
[ 17.634487] Symbol init_mm is marked as UNUSED, however this module is using it.
[ 17.638019] This symbol will go away in the future.
[ 17.643625] Please evalute if this is the right api to use and if it really is, submit a report the linux kernel mailinglist together with submitting your code for inclusion.
[ 17.680628] [fglrx] Maximum main memory to use for locked dma buffers: 913 MBytes.
[ 17.686808] [fglrx] ASYNCIO init succeed!
[ 17.695501] [fglrx] PAT is enabled successfully!
[ 17.702092] [fglrx] module loaded - fglrx 8.47.3 [Mar 29 2008] on minor 0
[ 18.023618] ip_tables: (C) 2000-2006 Netfilter Core Team
[ 18.174842] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[ 18.242753] arp_tables: (C) 2002 David S. Miller
[ 18.384488] ieee80211_crypt: registered algorithm 'NULL'
[ 18.424763] ieee80211: 802.11 data/management/control stack, git-1.1.13
[ 18.442138] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[ 18.465850] ieee80211_crypt: registered algorithm 'TKIP'
[ 18.581128] usbcore: registered new interface driver isight_firmware
[ 18.635730] ipmi message handler version 39.2
[ 18.656860] IPMI Watchdog: driver initialized
[ 18.832287] Adding 2988048k swap on /dev/disk/by-uuid/c58cdc7c-b94b-4116-9cca-bf154269e4d8. Priority:-1 extents:1 across:2988048k
[ 18.948826] usb 5-4: USB disconnect, address 3
[ 18.965351] EXT3 FS on sda1, internal journal
[ 20.924154] usb 5-4: new high speed USB device using ehci_hcd and address 6
[ 21.092287] usb 5-4: configuration #1 chosen from 1 choice
[ 21.092507] uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:8501)
[ 21.094812] uvcvideo: Failed to query (135) UVC control 1 (unit 0) : -32 (exp. 26).
[ 21.103175] input: Built-in iSight as /class/input/input13
[ 22.380229] appletouch: incomplete data package (first byte: 2, length: 4).
[ 24.124186] input: Pommed beeper device as /class/input/input14
[ 24.347589] Bluetooth: Core ver 2.11
[ 24.347604] NET: Registered protocol family 31
[ 24.347604] Bluetooth: HCI device and connection manager initialized
[ 24.347604] Bluetooth: HCI socket layer initialized
[ 24.411017] Bluetooth: L2CAP ver 2.9
[ 24.411017] Bluetooth: L2CAP socket layer initialized
[ 24.526645] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[ 24.555774] usb 4-1: usbfs: USBDEVFS_CONTROL failed cmd hid2hci rqt 64 rq 0 len 0 ret -71
[ 24.623504] Bluetooth: RFCOMM socket layer initialized
[ 24.623504] Bluetooth: RFCOMM TTY layer initialized
[ 24.623504] Bluetooth: RFCOMM ver 1.8
[ 24.897797] usb 4-1: USB disconnect, address 2
[ 25.256883] usb 4-1: new full speed USB device using uhci_hcd and address 3
[ 25.487680] usb 4-1: configuration #1 chosen from 1 choice
[ 25.535443] Bluetooth: HCI USB driver ver 2.9
[ 25.542689] usbcore: registered new interface driver hci_usb
[ 30.713538] input: Apple Computer, Inc. Mighty Mouse as /class/input/input15
[ 32.829872] CPA self-test:
[ 32.829933] 4k 0 large 224 gb 0 x 224[c0000000-f7c00000] miss 0
[ 32.845922] 4k 195584 large 33 gb 0 x 195617[c0000000-f7fff000] miss 0
[ 32.876168] 4k 195584 large 33 gb 0 x 195617[c0000000-f7fff000] miss 0
[ 32.876168] ok.
[ 36.993349] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[ 39.984583] [fglrx] Reserve Block - 0 offset = 0X7ffb000 length = 0X5000
[ 39.984583] [fglrx] Reserve Block - 1 offset = 0X0 length = 0X1000000
[ 39.984583] [fglrx] Reserve Block - 2 offset = 0X7fbb000 length = 0X40000
[ 40.153064] [fglrx] interrupt source 20008000 successfully enabled
[ 40.153064] [fglrx] enable ID = 0x00000008
[ 40.153064] [fglrx] Receive enable interrupt message with irqEnableMask: 20008000
[ 40.153064] [fglrx] interrupt source 10000000 successfully enabled
[ 40.153064] [fglrx] enable ID = 0x00000009
[ 40.153064] [fglrx] Receive enable interrupt message with irqEnableMask: 10000000
next reply other threads:[~2008-06-15 17:43 UTC|newest]
Thread overview: 5+ messages / expand[flat|nested] mbox.gz Atom feed top
2008-06-15 17:43 Justin Mattock [this message]
2008-06-16 16:44 ` Takashi Iwai
2008-06-16 16:57 ` Justin Mattock
2008-06-16 17:02 ` Takashi Iwai
2008-06-16 17:12 ` Justin Mattock
Reply instructions:
You may reply publicly to this message via plain-text email
using any one of the following methods:
* Save the following mbox file, import it into your mail client,
and reply-to-all from there: mbox
Avoid top-posting and favor interleaved quoting:
https://en.wikipedia.org/wiki/Posting_style#Interleaved_style
* Reply using the --to, --cc, and --in-reply-to
switches of git-send-email(1):
git send-email \
--in-reply-to=dd18b0c30806151043k46200e22lcaae79ad1f8209ed@mail.gmail.com \
--to=justinmattock@gmail.com \
--cc=linux-kernel@vger.kernel.org \
/path/to/YOUR_REPLY
https://kernel.org/pub/software/scm/git/docs/git-send-email.html
* If your mail client supports setting the In-Reply-To header
via mailto: links, try the mailto: link
Be sure your reply has a Subject: header at the top and a blank line
before the message body.
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®