mirror of https://lore.kernel.org/lkml/
 help / color / mirror / Atom feed
* audio: hda_intel azx_get_response timeout
@ 2008-06-15 17:43 Justin Mattock
  2008-06-16 16:44 ` Takashi Iwai
  0 siblings, 1 reply; 5+ messages in thread
From: Justin Mattock @ 2008-06-15 17:43 UTC (permalink / raw)
  To: Linux Kernel Mailing List

[-- Attachment #1: Type: text/plain, Size: 434 bytes --]

I've noticed this([   14.630815] hda_intel: azx_get_response timeout,
switching to polling mode: last cmd=0x00bf1c00
 with 2.6.26-rc2 or 3, when connecting external speakers to listen to
music(keep in mind this was only once),
Now with kernel 2.6.26-rc5 and 6 I'm seeing this pop up every so
often,(seen this three times now). attached is dmesg of the message.
If I see anything else I'll send a post.
regards;

-- 
Justin P. Mattock

[-- Attachment #2: hda_intel --]
[-- Type: application/octet-stream, Size: 39740 bytes --]

[    0.000000] Linux version 2.6.26-rc6-00079-g37a0cb0 (root@unix) (gcc version 4.2.3 (Debian 4.2.3-3)) #4 SMP Sun Jun 15 05:21:05 UTC 2008
[    0.000000] BIOS-provided physical RAM map:
[    0.000000]  BIOS-e820: 0000000000000000 - 000000000009fc00 (usable)
[    0.000000]  BIOS-e820: 000000000009fc00 - 00000000000a0000 (reserved)
[    0.000000]  BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved)
[    0.000000]  BIOS-e820: 0000000000100000 - 000000003f0ea000 (usable)
[    0.000000]  BIOS-e820: 000000003f0ea000 - 000000003f2eb000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003f2eb000 - 000000003febe000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003febe000 - 000000003feef000 (ACPI NVS)
[    0.000000]  BIOS-e820: 000000003feef000 - 000000003ff00000 (ACPI data)
[    0.000000]  BIOS-e820: 000000003ff00000 - 0000000040000000 (reserved)
[    0.000000]  BIOS-e820: 00000000f0000000 - 00000000f4000000 (reserved)
[    0.000000]  BIOS-e820: 00000000fec00000 - 00000000fec01000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed14000 - 00000000fed1a000 (reserved)
[    0.000000]  BIOS-e820: 00000000fed1c000 - 00000000fed20000 (reserved)
[    0.000000]  BIOS-e820: 00000000fee00000 - 00000000fee01000 (reserved)
[    0.000000]  BIOS-e820: 00000000ffe00000 - 0000000100000000 (reserved)
[    0.000000] 112MB HIGHMEM available.
[    0.000000] 896MB LOWMEM available.
[    0.000000] Entering add_active_range(0, 0, 258282) 0 entries of 256 used
[    0.000000] Zone PFN ranges:
[    0.000000]   DMA             0 ->     4096
[    0.000000]   Normal       4096 ->   229376
[    0.000000]   HighMem    229376 ->   258282
[    0.000000] Movable zone start PFN for each node
[    0.000000] early_node_map[1] active PFN ranges
[    0.000000]     0:        0 ->   258282
[    0.000000] On node 0 totalpages: 258282
[    0.000000]   DMA zone: 32 pages used for memmap
[    0.000000]   DMA zone: 0 pages reserved
[    0.000000]   DMA zone: 4064 pages, LIFO batch:0
[    0.000000]   Normal zone: 1760 pages used for memmap
[    0.000000]   Normal zone: 223520 pages, LIFO batch:31
[    0.000000]   HighMem zone: 226 pages used for memmap
[    0.000000]   HighMem zone: 28680 pages, LIFO batch:7
[    0.000000]   Movable zone: 0 pages used for memmap
[    0.000000] DMI 2.4 present.
[    0.000000] Using APIC driver default
[    0.000000] ACPI: RSDP 000FE020, 0024 (r2 APPLE )
[    0.000000] ACPI: XSDT 3FEFD1C0, 0074 (r1 APPLE   Apple00       A5       1000013)
[    0.000000] ACPI: FACP 3FEFB000, 00F4 (r3 APPLE   Apple00       A5 Loki       5F)
[    0.000000] ACPI: DSDT 3FEF0000, 48D1 (r1 APPLE  MacBookP    20002 INTL 20050309)
[    0.000000] ACPI: FACS 3FEC0000, 0040
[    0.000000] ACPI: HPET 3FEFA000, 0038 (r1 APPLE   Apple00        1 Loki       5F)
[    0.000000] ACPI: APIC 3FEF9000, 0068 (r1 APPLE   Apple00        1 Loki       5F)
[    0.000000] ACPI: MCFG 3FEF8000, 003C (r1 APPLE   Apple00        1 Loki       5F)
[    0.000000] ACPI: ASF! 3FEF7000, 00A0 (r32 APPLE   Apple00        1 Loki       5F)
[    0.000000] ACPI: SBST 3FEF6000, 0030 (r1 APPLE   Apple00        1 Loki       5F)
[    0.000000] ACPI: ECDT 3FEF5000, 0053 (r1 APPLE   Apple00        1 Loki       5F)
[    0.000000] ACPI: SSDT 3FEEF000, 04DC (r1 APPLE     CpuPm     3000 INTL 20050309)
[    0.000000] ACPI: SSDT 3FEBD000, 064F (r1 SataRe  SataPri     1000 INTL 20050309)
[    0.000000] ACPI: SSDT 3FEBC000, 069C (r1 SataRe  SataSec     1000 INTL 20050309)
[    0.000000] ACPI: DMI detected: Apple
[    0.000000] ACPI: PM-Timer IO Port: 0x408
[    0.000000] ACPI: Local APIC address 0xfee00000
[    0.000000] ACPI: LAPIC (acpi_id[0x00] lapic_id[0x00] enabled)
[    0.000000] ACPI: LAPIC (acpi_id[0x01] lapic_id[0x01] enabled)
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x00] high edge lint[0x1])
[    0.000000] ACPI: LAPIC_NMI (acpi_id[0x01] high edge lint[0x1])
[    0.000000] ACPI: IOAPIC (id[0x01] address[0xfec00000] gsi_base[0])
[    0.000000] IOAPIC[0]: apic_id 1, version 32, address 0xfec00000, GSI 0-23
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
[    0.000000] ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 high level)
[    0.000000] ACPI: IRQ0 used by override.
[    0.000000] ACPI: IRQ2 used by override.
[    0.000000] ACPI: IRQ9 used by override.
[    0.000000] Enabling APIC mode:  Flat.  Using 1 I/O APICs
[    0.000000] ACPI: HPET id: 0x8086a201 base: 0xfed00000
[    0.000000] Using ACPI (MADT) for SMP configuration information
[    0.000000] Allocating PCI resources starting at 50000000 (gap: 40000000:b0000000)
[    0.000000] PM: Registered nosave memory: 000000000009f000 - 00000000000a0000
[    0.000000] PM: Registered nosave memory: 00000000000a0000 - 00000000000e0000
[    0.000000] PM: Registered nosave memory: 00000000000e0000 - 0000000000100000
[    0.000000] SMP: Allowing 2 CPUs, 0 hotplug CPUs
[    0.000000] PERCPU: Allocating 46760 bytes of per cpu data
[    0.000000] NR_CPUS: 2, nr_cpu_ids: 2
[    0.000000] Built 1 zonelists in Zone order, mobility grouping on.  Total pages: 256264
[    0.000000] Kernel command line: root=/dev/sda1 ro quiet splash vga=773 selinux=1 audit=1 enforcing=1 debug acpi_osi=Linux pnpacpi=off pci=routeirq usbcore.autosuspend=1 nmi_watchdog=0
[    0.000000] audit: enabled (after initialization)
[    0.000000] ACPI: Added _OSI(Linux)
[    0.000000] mapped APIC to ffffb000 (fee00000)
[    0.000000] mapped IOAPIC to ffffa000 (fec00000)
[    0.000000] Enabling fast FPU save and restore... done.
[    0.000000] Enabling unmasked SIMD FPU exception support... done.
[    0.000000] Initializing CPU#0
[    0.000000] PID hash table entries: 4096 (order: 12, 16384 bytes)
[    0.000000] Extended CMOS year: 2000
[    0.000000] Detected 2161.324 MHz processor.
[    0.010000] Console: colour dummy device 80x25
[    0.010000] console [tty0] enabled
[    0.010000] Dentry cache hash table entries: 131072 (order: 7, 524288 bytes)
[    0.010000] Inode-cache hash table entries: 65536 (order: 6, 262144 bytes)
[    0.010000] Memory: 1018628k/1033128k available (2582k kernel code, 13884k reserved, 1332k data, 332k init, 115624k highmem)
[    0.010000] virtual kernel memory layout:
[    0.010000]     fixmap  : 0xfff7e000 - 0xfffff000   ( 516 kB)
[    0.010000]     pkmap   : 0xff800000 - 0xffc00000   (4096 kB)
[    0.010000]     vmalloc : 0xf8800000 - 0xff7fe000   ( 111 MB)
[    0.010000]     lowmem  : 0xc0000000 - 0xf8000000   ( 896 MB)
[    0.010000]       .init : 0xc04d9000 - 0xc052c000   ( 332 kB)
[    0.010000]       .data : 0xc0385a69 - 0xc04d2dac   (1332 kB)
[    0.010000]       .text : 0xc0100000 - 0xc0385a69   (2582 kB)
[    0.010000] Checking if this processor honours the WP bit even in supervisor mode...Ok.
[    0.010000] CPA: page pool initialized 1 of 1 pages preallocated
[    0.010000] SLUB: Genslabs=12, HWalign=64, Order=0-3, MinObjects=0, CPUs=2, Nodes=1
[    0.010000] hpet clockevent registered
[    0.159749] Calibrating delay using timer specific routine.. 4326.66 BogoMIPS (lpj=21633313)
[    0.159797] Security Framework initialized
[    0.159803] SELinux:  Initializing.
[    0.159816] SELinux:  Starting in enforcing mode
[    0.159822] selinux_register_security:  Registering secondary module capability
[    0.159827] Capability LSM initialized as secondary
[    0.159850] Mount-cache hash table entries: 512
[    0.160000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.160000] CPU: L2 cache: 4096K
[    0.160000] CPU: Physical Processor ID: 0
[    0.160000] CPU: Processor Core ID: 0
[    0.160000] Intel machine check architecture supported.
[    0.160000] Intel machine check reporting enabled on CPU#0.
[    0.160000] using mwait in idle threads.
[    0.160000] Checking 'hlt' instruction... OK.
[    0.200000] ACPI: Core revision 20080321
[    0.210000] ENABLING IO-APIC IRQs
[    0.210000] ..TIMER: vector=0x31 apic1=0 pin1=2 apic2=-1 pin2=-1
[    0.309939] CPU0: Intel(R) Core(TM)2 CPU         T7400  @ 2.16GHz stepping 06
[    0.310000] Booting processor 1/1 ip 6000
[    0.320000] Initializing CPU#1
[    0.320000] Calibrating delay using timer specific routine.. 4322.52 BogoMIPS (lpj=21612614)
[    0.320000] CPU: L1 I cache: 32K, L1 D cache: 32K
[    0.320000] CPU: L2 cache: 4096K
[    0.320000] CPU: Physical Processor ID: 0
[    0.320000] CPU: Processor Core ID: 1
[    0.320000] Intel machine check architecture supported.
[    0.320000] Intel machine check reporting enabled on CPU#1.
[    0.470000] CPU1: Intel(R) Core(TM)2 CPU         T7400  @ 2.16GHz stepping 06
[    0.470000] checking TSC synchronization [CPU#0 -> CPU#1]: passed.
[    0.470031] Brought up 2 CPUs
[    0.470037] Total of 2 processors activated (8649.18 BogoMIPS).
[    0.470060] CPU0 attaching sched-domain:
[    0.470065]  domain 0: span 0-1
[    0.470068]   groups: 0 1
[    0.470076] CPU1 attaching sched-domain:
[    0.470081]  domain 0: span 0-1
[    0.470084]   groups: 1 0
[    0.480000] net_namespace: 516 bytes
[    0.480000] Booting paravirtualized kernel on bare hardware
[    0.480000] NET: Registered protocol family 16
[    0.480000] No dock devices found.
[    0.480000] EISA bus registered
[    0.480000] ACPI: bus type pci registered
[    0.480000] PCI: Using configuration type 1 for base access
[    0.480000] Setting up standard PCI resources
[    0.480000] ACPI: EC: EC description table is found, configuring boot EC
[    0.480000] ACPI: EC: non-query interrupt received, switching to interrupt mode
[    0.497474] ACPI: BIOS _OSI(Linux) query honored via cmdline
[    0.498330] ACPI: Interpreter enabled
[    0.498335] ACPI: (supports S0 S3 S4 S5)
[    0.498394] ACPI: Using IOAPIC for interrupt routing
[    0.524110] ACPI: EC: GPE = 0x17, I/O: command/status = 0x66, data = 0x62
[    0.524116] ACPI: EC: driver started in interrupt mode
[    0.524921] ACPI: PCI Root Bridge [PCI0] (0000:00)
[    0.526621] pci 0000:00:1f.0: quirk: region 0400-047f claimed by ICH6 ACPI/GPIO/TCO
[    0.526630] pci 0000:00:1f.0: quirk: region 0500-053f claimed by ICH6 GPIO
[    0.527620] PCI: Transparent bridge - 0000:00:1e.0
[    0.527672] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT]
[    0.529219] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PEGP._PRT]
[    0.529702] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP01._PRT]
[    0.530000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP02._PRT]
[    0.530000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.RP03._PRT]
[    0.530000] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCIB._PRT]
[    0.550000] ACPI: PCI Interrupt Link [LNKA] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.550000] ACPI: PCI Interrupt Link [LNKB] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.550000] ACPI: PCI Interrupt Link [LNKC] (IRQs 1 3 4 5 6 7 10 12 14 15) *11
[    0.550000] ACPI: PCI Interrupt Link [LNKD] (IRQs 1 3 4 5 6 7 *11 12 14 15)
[    0.550000] ACPI: PCI Interrupt Link [LNKE] (IRQs 1 3 4 5 6 7 10 12 14 15) *0, disabled.
[    0.550000] ACPI: PCI Interrupt Link [LNKF] (IRQs 1 3 4 5 6 7 11 12 14 15) *0, disabled.
[    0.550000] ACPI: PCI Interrupt Link [LNKG] (IRQs 1 3 4 5 6 7 *10 12 14 15)
[    0.550000] ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 6 7 *11 12 14 15)
[    0.550000] Linux Plug and Play Support v0.97 (c) Adam Belay
[    0.550000] pnp: PnP ACPI: disabled
[    0.550000] SCSI subsystem initialized
[    0.550000] libata version 3.00 loaded.
[    0.560000] usbcore: registered new interface driver usbfs
[    0.560000] usbcore: registered new interface driver hub
[    0.560000] usbcore: registered new device driver usb
[    0.560000] PCI: Using ACPI for IRQ routing
[    0.560000] PCI: Routing PCI interrupts for all devices because "pci=routeirq" specified
[    0.560000] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.560000] ACPI: PCI Interrupt 0000:00:07.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.560000] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[    0.560000] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[    0.560000] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[    0.560000] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.560000] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[    0.560000] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[    0.560000] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.560000] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[    0.560000] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[    0.560000] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[    0.560000] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[    0.560000] ACPI: PCI Interrupt 0000:00:1f.3[B] -> GSI 19 (level, low) -> IRQ 19
[    0.560000] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.560000] ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.560000] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[    0.560000] ACPI: PCI Interrupt 0000:0c:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[    0.589877] NetLabel: Initializing
[    0.589882] NetLabel:  domain hash size = 128
[    0.589885] NetLabel:  protocols = UNLABELED CIPSOv4
[    0.589953] NetLabel:  unlabeled traffic allowed by default
[    0.589964] hpet0: at MMIO 0xfed00000, IRQs 2, 8, 0
[    0.589971] hpet0: 3 64-bit timers, 14318180 Hz
[    0.598804] Switched to high resolution mode on CPU 0
[    0.600749] Switched to high resolution mode on CPU 1
[    0.633759] PCI: Bridge: 0000:00:01.0
[    0.633764]   IO window: 3000-3fff
[    0.633770]   MEM window: 0x50300000-0x503fffff
[    0.633775]   PREFETCH window: 0x0000000040000000-0x0000000047ffffff
[    0.633783] PCI: Bridge: 0000:00:1c.0
[    0.633788]   IO window: 2000-2fff
[    0.633796]   MEM window: 0x50200000-0x502fffff
[    0.633802]   PREFETCH window: 0x0000000050500000-0x00000000505fffff
[    0.633813] PCI: Bridge: 0000:00:1c.1
[    0.633816]   IO window: disabled.
[    0.633823]   MEM window: 0x50100000-0x501fffff
[    0.633830]   PREFETCH window: disabled.
[    0.633839] PCI: Bridge: 0000:00:1c.2
[    0.633843]   IO window: 1000-1fff
[    0.633851]   MEM window: 0x4c100000-0x500fffff
[    0.633857]   PREFETCH window: 0x0000000048000000-0x000000004bffffff
[    0.633867] PCI: Bridge: 0000:00:1e.0
[    0.633871]   IO window: disabled.
[    0.633878]   MEM window: 0x4c000000-0x4c0fffff
[    0.633884]   PREFETCH window: disabled.
[    0.633904] ACPI: PCI Interrupt 0000:00:01.0[A] -> GSI 16 (level, low) -> IRQ 16
[    0.633913] PCI: Setting latency timer of device 0000:00:01.0 to 64
[    0.633939] ACPI: PCI Interrupt 0000:00:1c.0[A] -> GSI 17 (level, low) -> IRQ 17
[    0.633948] PCI: Setting latency timer of device 0000:00:1c.0 to 64
[    0.633976] ACPI: PCI Interrupt 0000:00:1c.1[B] -> GSI 16 (level, low) -> IRQ 16
[    0.633985] PCI: Setting latency timer of device 0000:00:1c.1 to 64
[    0.634012] ACPI: PCI Interrupt 0000:00:1c.2[C] -> GSI 18 (level, low) -> IRQ 18
[    0.634022] PCI: Setting latency timer of device 0000:00:1c.2 to 64
[    0.634038] PCI: Setting latency timer of device 0000:00:1e.0 to 64
[    0.634055] NET: Registered protocol family 2
[    0.662568] IP route cache hash table entries: 32768 (order: 5, 131072 bytes)
[    0.662848] TCP established hash table entries: 131072 (order: 8, 1048576 bytes)
[    0.663270] TCP bind hash table entries: 65536 (order: 8, 1310720 bytes)
[    0.663828] TCP: Hash tables configured (established 131072 bind 65536)
[    0.663833] TCP reno registered
[    0.672628] NET: Registered protocol family 1
[    0.682502] IA-32 Microcode Update Driver: v1.14a <tigran@aivazian.fsnet.co.uk>
[    0.692497] Initializing RT-Tester: OK
[    0.692497] audit: initializing netlink socket (enabled)
[    0.692497] type=2000 audit(1213507617.670:1): initialized
[    0.692498] highmem bounce pool size: 64 pages
[    0.692498] Total HugeTLB memory allocated, 0
[    0.703848] fuse init (API version 7.9)
[    0.704375] msgmni has been set to 1764
[    0.704591] SELinux:  Registering netfilter hooks
[    0.704800] io scheduler noop registered
[    0.705085] io scheduler cfq registered (default)
[    0.705219] pci 0000:01:00.0: Boot video device
[    0.705621] vesafb: framebuffer at 0x40000000, mapped to 0xf8880000, using 1536k, total 16384k
[    0.705629] vesafb: mode is 1024x768x8, linelength=1024, pages=18
[    0.705633] vesafb: protected mode interface info at c000:ad0c
[    0.705638] vesafb: pmi: set display start = c00cad94, set palette = c00cae50
[    0.705642] vesafb: scrolling: redraw
[    0.705646] vesafb: Pseudocolor: size=8:8:8:8, shift=0:0:0:0
[    0.718884] Console: switching to colour frame buffer device 128x48
[    0.731026] fb0: VESA VGA frame buffer device
[    0.731303] power_supply ADP1: uevent
[    0.731394] power_supply ADP1: No power supply yet
[    0.732498] power_supply ADP1: power_supply_changed
[    0.732498] ACPI: AC Adapter [ADP1] (on-line)
[    0.732498] power_supply ADP1: power_supply_changed_work
[    0.732498] power_supply ADP1: power_supply_update_gen_leds 1
[    0.732498] power_supply ADP1: uevent
[    0.732498] power_supply ADP1: POWER_SUPPLY_NAME=ADP1
[    0.732498] power_supply ADP1: Static prop TYPE=Mains
[    0.732624] power_supply ADP1: 1 dynamic props
[    0.732733] power_supply ADP1: prop ONLINE=1
[    0.857865] power_supply BAT0: uevent
[    0.857865] power_supply BAT0: No power supply yet
[    0.857865] power_supply BAT0: power_supply_changed
[    0.857865] power_supply BAT0: power_supply_changed_work
[    0.920336] ACPI: Battery Slot [BAT0] (battery present)
[    0.937835] hpet_resources: 0xfed00000 is busy
[    0.940341] loop: module loaded
[    0.944031] Linux video capture interface: v2.00
[    0.954020] input: Macintosh mouse button emulation as /class/input/input0
[    0.963166] Driver 'sd' needs updating - please use bus_type methods
[    0.963166] Driver 'sr' needs updating - please use bus_type methods
[    0.965506] power_supply BAT0: power_supply_update_bat_leds 4
[    0.965521] power_supply BAT0: uevent
[    0.965522] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[    0.965527] power_supply BAT0: Static prop TYPE=Battery
[    0.965531] power_supply BAT0: 12 dynamic props
[    0.965533] power_supply BAT0: prop STATUS=Full
[    0.965537] power_supply BAT0: prop PRESENT=1
[    0.965541] power_supply BAT0: prop TECHNOLOGY=Unknown
[    0.965545] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=10800000
[    0.965548] power_supply BAT0: prop VOLTAGE_NOW=12548000
[    0.965551] power_supply BAT0: prop CURRENT_NOW=0
[    0.965554] power_supply BAT0: prop ENERGY_FULL_DESIGN=55000000
[    0.965557] power_supply BAT0: prop ENERGY_FULL=53040000
[    0.965560] power_supply BAT0: prop ENERGY_NOW=52740000
[    0.965563] power_supply BAT0: prop MODEL_NAME=ASMB012
[    0.965566] power_supply BAT0: prop MANUFACTURER=SMPN012
[    0.965569] power_supply BAT0: prop SERIAL_NUMBER=
[    1.027297] ata_piix 0000:00:1f.1: version 2.12
[    1.028324] ACPI: PCI Interrupt 0000:00:1f.1[A] -> GSI 18 (level, low) -> IRQ 18
[    1.031325] PCI: Setting latency timer of device 0000:00:1f.1 to 64
[    1.031536] scsi0 : ata_piix
[    1.040471] scsi1 : ata_piix
[    1.040471] ata1: PATA max UDMA/100 cmd 0x1f0 ctl 0x3f6 bmdma 0x40b0 irq 14
[    1.046852] ata2: PATA max UDMA/100 cmd 0x170 ctl 0x376 bmdma 0x40b8 irq 15
[    1.223558] ata1.00: ATAPI: MATSHITADVD-R   UJ-857D, KCV9, max UDMA/66
[    1.263497] ata1.00: configured for UDMA/66
[    1.263497] scsi 0:0:0:0: CD-ROM            MATSHITA DVD-R   UJ-857D  KCV9 PQ: 0 ANSI: 5
[    1.444448] sr0: scsi3-mmc drive: 24x/24x writer cd/rw xa/form2 cdda tray
[    1.447689] Uniform CD-ROM driver Revision: 3.20
[    1.452978] sr 0:0:0:0: Attached scsi CD-ROM sr0
[    1.463315] sr 0:0:0:0: Attached scsi generic sg0 type 5
[    1.463315] ACPI: PCI Interrupt 0000:00:1f.2[B] -> GSI 19 (level, low) -> IRQ 19
[    1.463315] ata_piix 0000:00:1f.2: MAP [ P0 P2 -- -- ]
[    1.612993] PCI: Setting latency timer of device 0000:00:1f.2 to 64
[    1.622978] scsi2 : ata_piix
[    1.622978] scsi3 : ata_piix
[    1.633864] ata3: SATA max UDMA/133 cmd 0x40c8 ctl 0x40e4 bmdma 0x40a0 irq 19
[    1.633864] ata4: SATA max UDMA/133 cmd 0x40c0 ctl 0x40e0 bmdma 0x40a8 irq 19
[    1.814737] ata3.01: ATA-8: FUJITSU MHW2120BH, 00810013, max UDMA/100
[    1.818330] ata3.01: 234441648 sectors, multi 16: LBA48 NCQ (depth 0/32)
[    1.853483] ata3.01: configured for UDMA/100
[    2.024587] scsi 2:0:1:0: Direct-Access     ATA      FUJITSU MHW2120B 0081 PQ: 0 ANSI: 5
[    2.024587] sd 2:0:1:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[    2.024587] sd 2:0:1:0: [sda] Write Protect is off
[    2.041888] sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00
[    2.045607] sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.049554] sd 2:0:1:0: [sda] 234441648 512-byte hardware sectors (120034 MB)
[    2.059478] sd 2:0:1:0: [sda] Write Protect is off
[    2.059478] sd 2:0:1:0: [sda] Mode Sense: 00 3a 00 00
[    2.061385] sd 2:0:1:0: [sda] Write cache: enabled, read cache: enabled, doesn't support DPO or FUA
[    2.071344]  sda: sda1 sda2 < sda5 >
[    2.080068] sd 2:0:1:0: [sda] Attached SCSI disk
[    2.084255] sd 2:0:1:0: Attached scsi generic sg1 type 0
[    2.087587] usbcore: registered new interface driver usblcd
[    2.087587] usbcore: registered new interface driver usbled
[    2.087587] PNP: No PS/2 controller found. Probing ports directly.
[    2.105787] i8042.c: No controller found.
[    2.131598] mice: PS/2 mouse device common for all mice
[    2.131599] device-mapper: ioctl: 4.13.0-ioctl (2007-10-18) initialised: dm-devel@redhat.com
[    2.131599] EDAC MC: Ver: 2.1.0 Jun 14 2008
[    2.158697] cpuidle: using governor ladder
[    2.158697] cpuidle: using governor menu
[    2.165668] usbcore: registered new interface driver hiddev
[    2.167994] usbcore: registered new interface driver usbhid
[    2.172396] usbhid: v2.6:USB HID core driver
[    2.176982] Advanced Linux Sound Architecture Driver Version 1.0.16.
[    2.176984] ALSA device list:
[    2.185955]   No soundcards found.
[    2.194712] oprofile: using NMI interrupt.
[    2.194712] IPVS: Registered protocols (TCP, AH, ESP)
[    2.194712] IPVS: Connection hash table configured (size=4096, memory=32Kbytes)
[    2.207283] IPVS: ipvs loaded.
[    2.211555] Initializing XFRM netlink socket
[    2.217251] NET: Registered protocol family 17
[    2.221542] NET: Registered protocol family 15
[    2.225726] Using IPI No-Shortcut mode
[    2.234708] kjournald starting.  Commit interval 5 seconds
[    2.234378] EXT3-fs: mounted filesystem with ordered data mode.
[    2.234378] VFS: Mounted root (ext3 filesystem) readonly.
[    2.234378] Freeing unused kernel memory: 332k freed
[    2.937411] SELinux: 8192 avtab hash slots, 205781 rules.
[    3.072470] SELinux: 8192 avtab hash slots, 205781 rules.
[    3.252471] SELinux:  7 users, 7 roles, 3017 types, 90 bools
[    3.256656] SELinux:  72 classes, 205781 rules
[    3.273059] SELinux:  Completing initialization.
[    3.273678] SELinux:  Setting up existing superblocks.
[    3.305296] SELinux: initialized (dev sda1, type ext3), uses xattr
[    3.305296] SELinux: initialized (dev selinuxfs, type selinuxfs), uses genfs_contexts
[    3.305296] SELinux: initialized (dev mqueue, type mqueue), uses transition SIDs
[    3.305296] SELinux: initialized (dev hugetlbfs, type hugetlbfs), uses genfs_contexts
[    3.426680] SELinux: initialized (dev devpts, type devpts), uses transition SIDs
[    3.430718] SELinux: initialized (dev inotifyfs, type inotifyfs), uses genfs_contexts
[    3.434707] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    3.444703] SELinux: initialized (dev anon_inodefs, type anon_inodefs), uses genfs_contexts
[    3.444703] SELinux: initialized (dev pipefs, type pipefs), uses task SIDs
[    3.452529] SELinux: initialized (dev debugfs, type debugfs), uses genfs_contexts
[    3.456689] SELinux: initialized (dev sockfs, type sockfs), uses task SIDs
[    3.460592] SELinux: initialized (dev proc, type proc), uses genfs_contexts
[    3.468875] SELinux: initialized (dev bdev, type bdev), uses genfs_contexts
[    3.468875] SELinux: initialized (dev rootfs, type rootfs), uses genfs_contexts
[    3.472833] SELinux: initialized (dev sysfs, type sysfs), uses genfs_contexts
[    3.517454] SELinux: policy loaded with handle_unknown=deny
[    3.517454] type=1403 audit(1213507620.372:2): policy loaded auid=4294967295 ses=4294967295
[    4.628407] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[    4.643041] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   10.276431] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   10.514353] power_supply ADP1: uevent
[   10.523072] power_supply ADP1: POWER_SUPPLY_NAME=ADP1
[   10.527458] power_supply ADP1: Static prop TYPE=Mains
[   10.533024] power_supply ADP1: 1 dynamic props
[   10.541753] power_supply ADP1: prop ONLINE=1
[   10.546189] power_supply BAT0: uevent
[   10.550393] power_supply BAT0: POWER_SUPPLY_NAME=BAT0
[   10.551084] power_supply BAT0: Static prop TYPE=Battery
[   10.560232] power_supply BAT0: 12 dynamic props
[   10.713907] power_supply BAT0: prop STATUS=Full
[   10.719157] power_supply BAT0: prop PRESENT=1
[   10.723231] power_supply BAT0: prop TECHNOLOGY=Unknown
[   10.729143] power_supply BAT0: prop VOLTAGE_MIN_DESIGN=10800000
[   10.731323] power_supply BAT0: prop VOLTAGE_NOW=12548000
[   10.738325] power_supply BAT0: prop CURRENT_NOW=0
[   10.742261] power_supply BAT0: prop ENERGY_FULL_DESIGN=55000000
[   10.746180] power_supply BAT0: prop ENERGY_FULL=53040000
[   10.751277] power_supply BAT0: prop ENERGY_NOW=52740000
[   10.751336] power_supply BAT0: prop MODEL_NAME=ASMB012
[   10.755118] power_supply BAT0: prop MANUFACTURER=SMPN012
[   10.758834] power_supply BAT0: prop SERIAL_NUMBER=
[   11.830610] ACPI: SSDT 3FEB8C10, 02AE (r1 APPLE   Cpu0Ist     3000 INTL 20050309)
[   11.834357] ACPI: SSDT 3FEB8910, 02A0 (r1 APPLE   Cpu0Cst     3001 INTL 20050309)
[   11.834357] Monitor-Mwait will be used to enter C-1 state
[   11.840024] Monitor-Mwait will be used to enter C-2 state
[   11.843579] Monitor-Mwait will be used to enter C-3 state
[   11.849342] ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3])
[   11.852890] ACPI: ACPI0007:00 is registered as cooling_device0
[   11.856356] ACPI: Processor [CPU0] (supports 8 throttling states)
[   11.865405] ACPI: SSDT 3FEB8F10, 0087 (r1 APPLE   Cpu1Ist     3000 INTL 20050309)
[   11.867135] ACPI: SSDT 3FEB7F10, 0085 (r1 APPLE   Cpu1Cst     3000 INTL 20050309)
[   11.875379] ACPI: CPU1 (power states: C1[C1] C2[C2] C3[C3])
[   11.878816] ACPI: ACPI0007:01 is registered as cooling_device1
[   11.878816] Marking TSC unstable due to: TSC halts in idle.
[   11.888844] ACPI: Processor [CPU1] (supports 8 throttling states)
[   11.905383] input: Power Button (FF) as /class/input/input1
[   11.953066] ACPI: Power Button (FF) [PWRF]
[   11.956782] input: Lid Switch as /class/input/input2
[   11.960488] ACPI: Lid Switch [LID0]
[   11.963940] input: Power Button (CM) as /class/input/input3
[   12.012806] ACPI: Power Button (CM) [PWRB]
[   12.016247] input: Sleep Button (CM) as /class/input/input4
[   12.068613] ACPI: Sleep Button (CM) [SLPB]
[   12.078279] input: Video Bus as /class/input/input5
[   12.153804] ACPI: Video Device [GFX0] (multi-head: yes  rom: no  post: no)
[   12.221140] USB Universal Host Controller Interface driver v3.0
[   12.225047] ACPI: PCI Interrupt 0000:00:1d.0[A] -> GSI 23 (level, low) -> IRQ 23
[   12.231147] PCI: Setting latency timer of device 0000:00:1d.0 to 64
[   12.233507] uhci_hcd 0000:00:1d.0: UHCI Host Controller
[   12.237864] SELinux: initialized (dev usbfs, type usbfs), uses genfs_contexts
[   12.242040] uhci_hcd 0000:00:1d.0: new USB bus registered, assigned bus number 1
[   12.246261] uhci_hcd 0000:00:1d.0: irq 23, io base 0x00004080
[   12.250656] usb usb1: configuration #1 chosen from 1 choice
[   12.254096] hub 1-0:1.0: USB hub found
[   12.261019] hub 1-0:1.0: 2 ports detected
[   12.291221] ath_hal: module license 'Proprietary' taints kernel.
[   12.296694] ath_hal: 0.9.30.13 (AR5210, AR5211, AR5212, AR5416, RF5111, RF5112, RF2413, RF5413, RF2133)
[   12.368315] ACPI: PCI Interrupt 0000:00:1d.1[B] -> GSI 19 (level, low) -> IRQ 19
[   12.372901] PCI: Setting latency timer of device 0000:00:1d.1 to 64
[   12.376695] uhci_hcd 0000:00:1d.1: UHCI Host Controller
[   12.382276] uhci_hcd 0000:00:1d.1: new USB bus registered, assigned bus number 2
[   12.387153] uhci_hcd 0000:00:1d.1: irq 19, io base 0x00004060
[   12.392464] usb usb2: configuration #1 chosen from 1 choice
[   12.397328] hub 2-0:1.0: USB hub found
[   12.402228] hub 2-0:1.0: 2 ports detected
[   12.508472] ACPI: PCI Interrupt 0000:00:1d.2[C] -> GSI 18 (level, low) -> IRQ 18
[   12.513401] PCI: Setting latency timer of device 0000:00:1d.2 to 64
[   12.518174] uhci_hcd 0000:00:1d.2: UHCI Host Controller
[   12.523225] uhci_hcd 0000:00:1d.2: new USB bus registered, assigned bus number 3
[   12.528463] uhci_hcd 0000:00:1d.2: irq 18, io base 0x00004040
[   12.533603] usb usb3: configuration #1 chosen from 1 choice
[   12.538647] hub 3-0:1.0: USB hub found
[   12.543516] hub 3-0:1.0: 2 ports detected
[   12.594926] wlan: svn r3692
[   12.655252] usb 1-2: new full speed USB device using uhci_hcd and address 2
[   12.667947] ACPI: PCI Interrupt 0000:00:1d.3[D] -> GSI 16 (level, low) -> IRQ 16
[   12.667947] PCI: Setting latency timer of device 0000:00:1d.3 to 64
[   12.668567] uhci_hcd 0000:00:1d.3: UHCI Host Controller
[   12.677946] uhci_hcd 0000:00:1d.3: new USB bus registered, assigned bus number 4
[   12.686190] uhci_hcd 0000:00:1d.3: irq 16, io base 0x00004020
[   12.691372] usb usb4: configuration #1 chosen from 1 choice
[   12.696473] hub 4-0:1.0: USB hub found
[   12.702624] hub 4-0:1.0: 2 ports detected
[   12.829659] ACPI: PCI Interrupt 0000:00:1d.7[A] -> GSI 23 (level, low) -> IRQ 23
[   12.836355] PCI: Setting latency timer of device 0000:00:1d.7 to 64
[   12.841381] ehci_hcd 0000:00:1d.7: EHCI Host Controller
[   12.848603] ehci_hcd 0000:00:1d.7: new USB bus registered, assigned bus number 5
[   12.859319] ehci_hcd 0000:00:1d.7: debug port 1
[   12.859319] PCI: cache line size of 32 is not supported by device 0000:00:1d.7
[   12.864245] ehci_hcd 0000:00:1d.7: irq 23, io mem 0x50405400
[   12.895706] usb 1-2: configuration #1 chosen from 1 choice
[   12.895722] ehci_hcd 0000:00:1d.7: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
[   12.895856] usb usb5: configuration #1 chosen from 1 choice
[   12.895925] hub 5-0:1.0: USB hub found
[   12.895936] hub 5-0:1.0: 8 ports detected
[   12.937398] usb 1-2: can't set config #1, error -71
[   12.967882] ath_pci: svn r3692
[   13.028570] ACPI: PCI Interrupt 0000:0c:03.0[A] -> GSI 19 (level, low) -> IRQ 19
[   13.086777] ohci1394: fw-host0: OHCI-1394 1.1 (PCI): IRQ=[19]  MMIO=[4c004000-4c0047ff]  Max Packet=[4096]  IR/IT contexts=[4/8]
[   13.107571] ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 17
[   13.107571] PCI: Setting latency timer of device 0000:03:00.0 to 64
[   13.247640] MadWifi: ath_attach: HAL managed transmit power control (TPC) disabled.
[   13.247640] MadWifi: ath_attach: Interference mitigation is supported.  Currently disabled.
[   13.257527] MadWifi: ath_attach: Switching rfkill capability off.
[   13.306872] usb 1-2: USB disconnect, address 2
[   13.363241] ath_rate_sample: 1.2 (svn r3692)
[   13.371205] wifi0: 11a rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   13.371205] wifi0: 11b rates: 1Mbps 2Mbps 5.5Mbps 11Mbps
[   13.372476] wifi0: 11g rates: 1Mbps 2Mbps 5.5Mbps 11Mbps 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   13.378678] wifi0: turboA rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   13.384303] wifi0: turboG rates: 6Mbps 9Mbps 12Mbps 18Mbps 24Mbps 36Mbps 48Mbps 54Mbps
[   13.389624] wifi0: H/W encryption support: WEP AES AES_CCM TKIP
[   13.398729] wifi0: Atheros AR5418 chip found (MAC 12.10, PHY SChip 8.1, Radio 12.0)
[   13.404082] wifi0: Use hw queue 1 for WME_AC_BE traffic
[   13.409450] wifi0: Use hw queue 0 for WME_AC_BK traffic
[   13.414718] wifi0: Use hw queue 2 for WME_AC_VI traffic
[   13.429455] wifi0: Use hw queue 3 for WME_AC_VO traffic
[   13.429953] wifi0: Use hw queue 4 for XR traffic
[   13.434774] wifi0: Use hw queue 7 for UAPSD traffic
[   13.439604] wifi0: Use hw queue 8 for CAB traffic
[   13.444939] wifi0: Use hw queue 9 for beacons
[   13.526135] ath_pci: wifi0: Atheros 5418: mem=0x50100000, irq=17
[   13.530685] ACPI: PCI Interrupt 0000:00:1b.0[A] -> GSI 22 (level, low) -> IRQ 22
[   13.531868] PCI: Setting latency timer of device 0000:00:1b.0 to 64
[   13.615526] hda_codec: STAC922x, Apple subsys_id=106b1e00
[   14.205555] usb 5-4: new high speed USB device using ehci_hcd and address 3
[   14.364967] usb 5-4: configuration #1 chosen from 1 choice
[   14.450815] ieee1394: Host added: ID:BUS[0-00:1023]  GUID[0019e3fffe2ad87e]
[   14.630815] hda_intel: azx_get_response timeout, switching to polling mode: last cmd=0x00bf1c00
[   14.994484] Clocksource tsc unstable (delta = -313768306 ns)
[   15.220838] usb 1-2: new full speed USB device using uhci_hcd and address 3
[   15.415624] usb 1-2: configuration #1 chosen from 1 choice
[   15.432925] input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input6
[   15.466406] input: USB HID v1.11 Keyboard [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2
[   15.478891] input: Apple Computer Apple Internal Keyboard / Trackpad as /class/input/input7
[   15.495817] input: USB HID v1.11 Device [Apple Computer Apple Internal Keyboard / Trackpad] on usb-0000:00:1d.0-2
[   15.777185] usb 3-2: new full speed USB device using uhci_hcd and address 2
[   15.961843] usb 3-2: configuration #1 chosen from 1 choice
[   15.976903] hiddev0: USB HID v1.11 Device [Apple Computer, Inc. IR Receiver] on usb-0000:00:1d.2-2
[   16.263427] usb 4-1: new full speed USB device using uhci_hcd and address 2
[   16.468403] usb 4-1: configuration #1 chosen from 1 choice
[   16.506102] input: HID 05ac:1000 as /class/input/input8
[   16.519580] input: USB HID v1.11 Keyboard [HID 05ac:1000] on usb-0000:00:1d.3-1
[   16.548703] input: HID 05ac:1000 as /class/input/input9
[   16.558611] input: USB HID v1.11 Mouse [HID 05ac:1000] on usb-0000:00:1d.3-1
[   16.667223] uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:8501)
[   16.674956] uvcvideo: Failed to query (135) UVC control 1 (unit 0) : -32 (exp. 26).
[   16.687221] input: Built-in iSight as /class/input/input10
[   16.739247] usbcore: registered new interface driver uvcvideo
[   16.744342] USB Video Class driver (SVN r212)
[   16.767009] appletouch: Geyser mode initialized.
[   16.776007] input: appletouch as /class/input/input11
[   16.903945] usbcore: registered new interface driver appletouch
[   17.291060] SELinux: initialized (dev tmpfs, type tmpfs), uses transition SIDs
[   17.382056] applesmc: Apple MacBook Pro detected:
[   17.389438] applesmc:  - Model with accelerometer
[   17.400206] applesmc:  - Model with light sensors and backlight
[   17.400208] applesmc:  - Model with 12 temperature sensors
[   17.407743] applesmc: device has already been initialized (0xe0, 0x00).
[   17.407745] applesmc: device successfully initialized.
[   17.408204] applesmc: 2 fans found.
[   17.408930] input: applesmc as /class/input/input12
[   17.472313] Registered led device: smc::kbd_backlight
[   17.472313] applesmc: driver successfully loaded.
[   17.536222] Linux agpgart interface v0.103
[   17.634487] Symbol init_mm is marked as UNUSED, however this module is using it.
[   17.638019] This symbol will go away in the future.
[   17.643625] Please evalute if this is the right api to use and if it really is, submit a report the linux kernel mailinglist together with submitting your code for inclusion.
[   17.680628] [fglrx] Maximum main memory to use for locked dma buffers: 913 MBytes.
[   17.686808] [fglrx] ASYNCIO init succeed!
[   17.695501] [fglrx] PAT is enabled successfully!
[   17.702092] [fglrx] module loaded - fglrx 8.47.3 [Mar 29 2008] on minor 0
[   18.023618] ip_tables: (C) 2000-2006 Netfilter Core Team
[   18.174842] nf_conntrack version 0.5.0 (16384 buckets, 65536 max)
[   18.242753] arp_tables: (C) 2002 David S. Miller
[   18.384488] ieee80211_crypt: registered algorithm 'NULL'
[   18.424763] ieee80211: 802.11 data/management/control stack, git-1.1.13
[   18.442138] ieee80211: Copyright (C) 2004-2005 Intel Corporation <jketreno@linux.intel.com>
[   18.465850] ieee80211_crypt: registered algorithm 'TKIP'
[   18.581128] usbcore: registered new interface driver isight_firmware
[   18.635730] ipmi message handler version 39.2
[   18.656860] IPMI Watchdog: driver initialized
[   18.832287] Adding 2988048k swap on /dev/disk/by-uuid/c58cdc7c-b94b-4116-9cca-bf154269e4d8.  Priority:-1 extents:1 across:2988048k
[   18.948826] usb 5-4: USB disconnect, address 3
[   18.965351] EXT3 FS on sda1, internal journal
[   20.924154] usb 5-4: new high speed USB device using ehci_hcd and address 6
[   21.092287] usb 5-4: configuration #1 chosen from 1 choice
[   21.092507] uvcvideo: Found UVC 1.00 device Built-in iSight (05ac:8501)
[   21.094812] uvcvideo: Failed to query (135) UVC control 1 (unit 0) : -32 (exp. 26).
[   21.103175] input: Built-in iSight as /class/input/input13
[   22.380229] appletouch: incomplete data package (first byte: 2, length: 4).
[   24.124186] input: Pommed beeper device as /class/input/input14
[   24.347589] Bluetooth: Core ver 2.11
[   24.347604] NET: Registered protocol family 31
[   24.347604] Bluetooth: HCI device and connection manager initialized
[   24.347604] Bluetooth: HCI socket layer initialized
[   24.411017] Bluetooth: L2CAP ver 2.9
[   24.411017] Bluetooth: L2CAP socket layer initialized
[   24.526645] Bluetooth: HIDP (Human Interface Emulation) ver 1.2
[   24.555774] usb 4-1: usbfs: USBDEVFS_CONTROL failed cmd hid2hci rqt 64 rq 0 len 0 ret -71
[   24.623504] Bluetooth: RFCOMM socket layer initialized
[   24.623504] Bluetooth: RFCOMM TTY layer initialized
[   24.623504] Bluetooth: RFCOMM ver 1.8
[   24.897797] usb 4-1: USB disconnect, address 2
[   25.256883] usb 4-1: new full speed USB device using uhci_hcd and address 3
[   25.487680] usb 4-1: configuration #1 chosen from 1 choice
[   25.535443] Bluetooth: HCI USB driver ver 2.9
[   25.542689] usbcore: registered new interface driver hci_usb
[   30.713538] input: Apple Computer, Inc. Mighty Mouse as /class/input/input15
[   32.829872] CPA self-test:
[   32.829933]  4k 0 large 224 gb 0 x 224[c0000000-f7c00000] miss 0
[   32.845922]  4k 195584 large 33 gb 0 x 195617[c0000000-f7fff000] miss 0
[   32.876168]  4k 195584 large 33 gb 0 x 195617[c0000000-f7fff000] miss 0
[   32.876168] ok.
[   36.993349] ACPI: PCI Interrupt 0000:01:00.0[A] -> GSI 16 (level, low) -> IRQ 16
[   39.984583] [fglrx] Reserve Block - 0 offset =  0X7ffb000 length = 0X5000
[   39.984583] [fglrx] Reserve Block - 1 offset =  0X0 length = 0X1000000
[   39.984583] [fglrx] Reserve Block - 2 offset =  0X7fbb000 length = 0X40000
[   40.153064] [fglrx] interrupt source 20008000 successfully enabled
[   40.153064] [fglrx] enable ID = 0x00000008
[   40.153064] [fglrx] Receive enable interrupt message with irqEnableMask: 20008000
[   40.153064] [fglrx] interrupt source 10000000 successfully enabled
[   40.153064] [fglrx] enable ID = 0x00000009
[   40.153064] [fglrx] Receive enable interrupt message with irqEnableMask: 10000000

^ permalink raw reply	[flat|nested] 5+ messages in thread
end of thread, other threads:[~2008-06-16 17:12 UTC | newest]

Thread overview: 5+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2008-06-15 17:43 audio: hda_intel azx_get_response timeout Justin Mattock
2008-06-16 16:44 ` Takashi Iwai
2008-06-16 16:57   ` Justin Mattock
2008-06-16 17:02     ` Takashi Iwai
2008-06-16 17:12       ` Justin Mattock

This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®