Re: [PATCH net-next v1 1/3] net: stmmac: Switch to zero-copy in non-XDP RX path

[Yanteng Si <si.yanteng@linux.dev>]

在 2025/1/10 17:53, Furong Xu 写道:
> Avoid memcpy in non-XDP RX path by marking all allocated SKBs to
> be recycled in the upper network stack.
> 
> This patch brings ~11.5% driver performance improvement in a TCP RX
> throughput test with iPerf tool on a single isolated Cortex-A65 CPU
> core, from 2.18 Gbits/sec increased to 2.43 Gbits/sec.
> 
> Signed-off-by: Furong Xu <0x1207@gmail.com>
> ---
>   drivers/net/ethernet/stmicro/stmmac/stmmac.h  |  1 +
>   .../net/ethernet/stmicro/stmmac/stmmac_main.c | 23 +++++++++++--------
>   2 files changed, 15 insertions(+), 9 deletions(-)
> 
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac.h b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> index 548b28fed9b6..5c39292313de 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac.h
> @@ -126,6 +126,7 @@ struct stmmac_rx_queue {
>   	unsigned int cur_rx;
>   	unsigned int dirty_rx;
>   	unsigned int buf_alloc_num;
> +	unsigned int napi_skb_frag_size;
>   	dma_addr_t dma_rx_phy;
>   	u32 rx_tail_addr;
>   	unsigned int state_saved;
> diff --git a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> index 038df1b2bb58..43125a6f8f6b 100644
> --- a/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> +++ b/drivers/net/ethernet/stmicro/stmmac/stmmac_main.c
> @@ -1320,7 +1320,7 @@ static unsigned int stmmac_rx_offset(struct stmmac_priv *priv)
>   	if (stmmac_xdp_is_enabled(priv))
>   		return XDP_PACKET_HEADROOM;
>   
> -	return 0;
> +	return NET_SKB_PAD;
>   }
>   
>   static int stmmac_set_bfsize(int mtu, int bufsize)
> @@ -2019,17 +2019,21 @@ static int __alloc_dma_rx_desc_resources(struct stmmac_priv *priv,
>   	struct stmmac_channel *ch = &priv->channel[queue];
>   	bool xdp_prog = stmmac_xdp_is_enabled(priv);
>   	struct page_pool_params pp_params = { 0 };
> -	unsigned int num_pages;
> +	unsigned int dma_buf_sz_pad, num_pages;
>   	unsigned int napi_id;
>   	int ret;
>   
> +	dma_buf_sz_pad = stmmac_rx_offset(priv) + dma_conf->dma_buf_sz +
> +			 SKB_DATA_ALIGN(sizeof(struct skb_shared_info));
> +	num_pages = DIV_ROUND_UP(dma_buf_sz_pad, PAGE_SIZE);
> +
>   	rx_q->queue_index = queue;
>   	rx_q->priv_data = priv;
> +	rx_q->napi_skb_frag_size = num_pages * PAGE_SIZE;
>   
>   	pp_params.flags = PP_FLAG_DMA_MAP | PP_FLAG_DMA_SYNC_DEV;
>   	pp_params.pool_size = dma_conf->dma_rx_size;
> -	num_pages = DIV_ROUND_UP(dma_conf->dma_buf_sz, PAGE_SIZE);
> -	pp_params.order = ilog2(num_pages);
> +	pp_params.order = order_base_2(num_pages);
>   	pp_params.nid = dev_to_node(priv->device);
>   	pp_params.dev = priv->device;
>   	pp_params.dma_dir = xdp_prog ? DMA_BIDIRECTIONAL : DMA_FROM_DEVICE;
> @@ -5574,19 +5578,20 @@ static int stmmac_rx(struct stmmac_priv *priv, int limit, u32 queue)
>   			/* XDP program may expand or reduce tail */
>   			buf1_len = ctx.xdp.data_end - ctx.xdp.data;
>   
> -			skb = napi_alloc_skb(&ch->rx_napi, buf1_len);
> +			skb = napi_build_skb(page_address(buf->page),
> +					     rx_q->napi_skb_frag_size);
>   			if (!skb) {
> +				page_pool_recycle_direct(rx_q->page_pool,
> +							 buf->page);
>   				rx_dropped++;
>   				count++;
>   				goto drain_data;
>   			}
>   
>   			/* XDP program may adjust header */
> -			skb_copy_to_linear_data(skb, ctx.xdp.data, buf1_len);
> +			skb_reserve(skb, ctx.xdp.data - ctx.xdp.data_hard_start);
The network subsystem still requires that the length
of each line of code should not exceed 80 characters.
So let's silence the warning:

WARNING: line length of 81 exceeds 80 columns
#87: FILE: drivers/net/ethernet/stmicro/stmmac/stmmac_main.c:5592:
+			skb_reserve(skb, ctx.xdp.data - ctx.xdp.data_hard_start);

Thanks,
Yanteng