* [PATCH] x86: Make the 64-bit bzImage always physically relocatable
@ 2026-11-11 9:18 Ard Biesheuvel
2026-11-18 11:23 ` Ard Biesheuvel
2026-11-18 15:51 ` H. Peter Anvin
0 siblings, 2 replies; 9+ messages in thread
From: Ard Biesheuvel @ 2026-11-11 9:18 UTC (permalink / raw)
To: x86; +Cc: linux-kernel, linux-efi, hpa, Ard Biesheuvel
From: Ard Biesheuvel <ardb@kernel.org>
On x86_64, the physical placement of the kernel is independent from its
mapping in the 'High Kernel Mapping' range. This means that even a
position dependent kernel built without boot-time relocation support can
run from any suitably aligned physical address, and there is no need to
make this behavior dependent on whether or not the kernel is virtually
relocatable.
On i386, the situation is different, given that the physical and virtual
load offsets must be equal, and so only a relocatable kernel can be
loaded at a physical address that deviates from its build-time default.
Clarify this in Kconfig and in the code, and advertise the 64-bit
bzImage as loadable at any physical offset regardless of whether
CONFIG_RELOCATABLE is set. In practice, this makes little difference,
given that it defaults to 'y' and is a prerequisite for EFI_STUB and
RANDOMIZE_BASE, but it will help with some future refactoring of the
relocation code.
Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
---
arch/x86/Kconfig | 40 ++++++++++++++++++------------
arch/x86/boot/compressed/head_64.S | 4 ---
arch/x86/boot/compressed/misc.c | 8 +++---
| 8 ++----
4 files changed, 29 insertions(+), 31 deletions(-)
diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
index 58dce0b66179..c7427daa0c3e 100644
--- a/arch/x86/Kconfig
+++ b/arch/x86/Kconfig
@@ -1898,7 +1898,7 @@ config EFI
config EFI_STUB
bool "EFI stub support"
depends on EFI
- select RELOCATABLE
+ select RELOCATABLE if X86_32
help
This kernel feature allows a bzImage to be loaded directly
by EFI firmware without the use of a bootloader.
@@ -1995,8 +1995,9 @@ config PHYSICAL_START
help
This gives the physical address where the kernel is loaded.
- If the kernel is not relocatable (CONFIG_RELOCATABLE=n) then bzImage
- will decompress itself to above physical address and run from there.
+ If the kernel is not relocatable (CONFIG_RELOCATABLE=n) and built for
+ i386, then the bzImage will decompress itself to the above physical
+ address and run from there.
Otherwise, bzImage will run from the address where it has been loaded
by the boot loader. The only exception is if it is loaded below the
above physical address, in which case it will relocate itself there.
@@ -2031,16 +2032,22 @@ config PHYSICAL_START
Don't change this unless you know what you are doing.
config RELOCATABLE
- bool "Build a relocatable kernel"
- default y
+ bool "Build a relocatable kernel" if X86_32
+ default X86_32
help
- This builds a kernel image that retains relocation information
- so it can be loaded someplace besides the default 1MB.
+ This builds a kernel image that retains relocation information so it
+ can be placed someplace besides the default PAGE_OFFSET + 1MB. This
+ is a prerequisite for KASLR.
The relocations tend to make the kernel binary about 10% larger,
but are discarded at runtime.
- One use is for the kexec on panic case where the recovery kernel
- must live at a different physical address than the primary
+ On i386, where the virtual and physical load offset of the kernel
+ must be equal, this also allows the kernel image to be placed at a
+ physical load address that differs from the compile time default. On
+ x86_64, this is always permitted.
+
+ One use is for the kexec on panic case on i386, where the recovery
+ kernel must live at a different physical address than the primary
kernel.
Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
@@ -2049,7 +2056,7 @@ config RELOCATABLE
config RANDOMIZE_BASE
bool "Randomize the address of the kernel image (KASLR)"
- depends on RELOCATABLE
+ select RELOCATABLE
default y
help
In support of Kernel Address Space Layout Randomization (KASLR),
@@ -2085,7 +2092,7 @@ config RANDOMIZE_BASE
# Relocation on x86 needs some additional build support
config X86_NEED_RELOCS
def_bool y
- depends on RANDOMIZE_BASE || (X86_32 && RELOCATABLE)
+ depends on RELOCATABLE
select ARCH_VMLINUX_NEEDS_RELOCS
config PHYSICAL_ALIGN
@@ -2098,12 +2105,13 @@ config PHYSICAL_ALIGN
where kernel is loaded and run from. Kernel is compiled for an
address which meets above alignment restriction.
- If bootloader loads the kernel at a non-aligned address and
- CONFIG_RELOCATABLE is set, kernel will move itself to nearest
- address aligned to above value and run from there.
+ If the bootloader loads the kernel at a non-aligned address and it
+ is built for x86_64 or CONFIG_RELOCATABLE is set, the kernel will
+ move itself to the nearest address aligned to above value and run
+ from there.
- If bootloader loads the kernel at a non-aligned address and
- CONFIG_RELOCATABLE is not set, kernel will ignore the run time
+ If the bootloader loads the i386 kernel at a non-aligned address and
+ CONFIG_RELOCATABLE is not set, the kernel will ignore the run time
load address and decompress itself to the address it has been
compiled for and run from there. The address for which kernel is
compiled already meets above alignment restrictions. Hence the
diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S
index 1aca51390f73..de1973f032c7 100644
--- a/arch/x86/boot/compressed/head_64.S
+++ b/arch/x86/boot/compressed/head_64.S
@@ -143,7 +143,6 @@ SYM_FUNC_START(startup_32)
* for safe in-place decompression.
*/
-#ifdef CONFIG_RELOCATABLE
movl %ebp, %ebx
movl BP_kernel_alignment(%esi), %eax
decl %eax
@@ -152,7 +151,6 @@ SYM_FUNC_START(startup_32)
andl %eax, %ebx
cmpl $LOAD_PHYSICAL_ADDR, %ebx
jae 1f
-#endif
movl $LOAD_PHYSICAL_ADDR, %ebx
1:
@@ -316,7 +314,6 @@ SYM_CODE_START(startup_64)
*/
/* Start with the delta to where the kernel will run at. */
-#ifdef CONFIG_RELOCATABLE
leaq startup_32(%rip) /* - $startup_32 */, %rbp
movl BP_kernel_alignment(%rsi), %eax
decl %eax
@@ -325,7 +322,6 @@ SYM_CODE_START(startup_64)
andq %rax, %rbp
cmpq $LOAD_PHYSICAL_ADDR, %rbp
jae 1f
-#endif
movq $LOAD_PHYSICAL_ADDR, %rbp
1:
diff --git a/arch/x86/boot/compressed/misc.c b/arch/x86/boot/compressed/misc.c
index 0f41ca0e52c0..d37569e7ee10 100644
--- a/arch/x86/boot/compressed/misc.c
+++ b/arch/x86/boot/compressed/misc.c
@@ -314,12 +314,10 @@ static size_t parse_elf(void *output)
if ((phdr->p_align % 0x200000) != 0)
error("Alignment of LOAD segment isn't multiple of 2MB");
#endif
-#ifdef CONFIG_RELOCATABLE
- dest = output;
- dest += (phdr->p_paddr - LOAD_PHYSICAL_ADDR);
-#else
dest = (void *)(phdr->p_paddr);
-#endif
+ if (IS_ENABLED(CONFIG_X86_64) ||
+ IS_ENABLED(CONFIG_RELOCATABLE))
+ dest += (unsigned long)output - LOAD_PHYSICAL_ADDR;
memmove(dest, output + phdr->p_offset, phdr->p_filesz);
break;
default: /* Ignore other PT_* */ break;
--git a/arch/x86/boot/header.S b/arch/x86/boot/header.S
index 9bea5a1e2c52..b72e6055e103 100644
--- a/arch/x86/boot/header.S
+++ b/arch/x86/boot/header.S
@@ -332,7 +332,7 @@ initrd_addr_max: .long 0x7fffffff
kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment
#required for protected mode
#kernel
-#ifdef CONFIG_RELOCATABLE
+#if defined(CONFIG_RELOCATABLE) || defined(CONFIG_X86_64)
relocatable_kernel: .byte 1
#else
relocatable_kernel: .byte 0
@@ -342,14 +342,10 @@ min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment
xloadflags:
#ifdef CONFIG_X86_64
# define XLF0 XLF_KERNEL_64 /* 64-bit kernel */
-#else
-# define XLF0 0
-#endif
-
-#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_X86_64)
/* kernel/boot_param/ramdisk could be loaded above 4g */
# define XLF1 XLF_CAN_BE_LOADED_ABOVE_4G
#else
+# define XLF0 0
# define XLF1 0
#endif
--
2.56.0.611.g1030f0b940-goog
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-11 9:18 [PATCH] x86: Make the 64-bit bzImage always physically relocatable Ard Biesheuvel
@ 2026-11-18 11:23 ` Ard Biesheuvel
2026-11-18 15:51 ` H. Peter Anvin
1 sibling, 0 replies; 9+ messages in thread
From: Ard Biesheuvel @ 2026-11-18 11:23 UTC (permalink / raw)
To: Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi, H . Peter Anvin
On Wed, 11 Nov 2026, at 10:18, Ard Biesheuvel wrote:
> From: Ard Biesheuvel <ardb@kernel.org>
>
> On x86_64, the physical placement of the kernel is independent from its
> mapping in the 'High Kernel Mapping' range. This means that even a
> position dependent kernel built without boot-time relocation support can
> run from any suitably aligned physical address, and there is no need to
> make this behavior dependent on whether or not the kernel is virtually
> relocatable.
>
> On i386, the situation is different, given that the physical and virtual
> load offsets must be equal, and so only a relocatable kernel can be
> loaded at a physical address that deviates from its build-time default.
>
> Clarify this in Kconfig and in the code, and advertise the 64-bit
> bzImage as loadable at any physical offset regardless of whether
> CONFIG_RELOCATABLE is set. In practice, this makes little difference,
> given that it defaults to 'y' and is a prerequisite for EFI_STUB and
> RANDOMIZE_BASE, but it will help with some future refactoring of the
> relocation code.
>
> Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
> ---
> arch/x86/Kconfig | 40 ++++++++++++++++++------------
> arch/x86/boot/compressed/head_64.S | 4 ---
> arch/x86/boot/compressed/misc.c | 8 +++---
> arch/x86/boot/header.S | 8 ++----
> 4 files changed, 29 insertions(+), 31 deletions(-)
>
Ping?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-11 9:18 [PATCH] x86: Make the 64-bit bzImage always physically relocatable Ard Biesheuvel
2026-11-18 11:23 ` Ard Biesheuvel
@ 2026-11-18 15:51 ` H. Peter Anvin
2026-11-18 16:18 ` Ard Biesheuvel
1 sibling, 1 reply; 9+ messages in thread
From: H. Peter Anvin @ 2026-11-18 15:51 UTC (permalink / raw)
To: Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi, Ard Biesheuvel
On November 11, 2026 1:18:44 AM PST, Ard Biesheuvel <ardb+git@google.com> wrote:
>From: Ard Biesheuvel <ardb@kernel.org>
>
>On x86_64, the physical placement of the kernel is independent from its
>mapping in the 'High Kernel Mapping' range. This means that even a
>position dependent kernel built without boot-time relocation support can
>run from any suitably aligned physical address, and there is no need to
>make this behavior dependent on whether or not the kernel is virtually
>relocatable.
>
>On i386, the situation is different, given that the physical and virtual
>load offsets must be equal, and so only a relocatable kernel can be
>loaded at a physical address that deviates from its build-time default.
>
>Clarify this in Kconfig and in the code, and advertise the 64-bit
>bzImage as loadable at any physical offset regardless of whether
>CONFIG_RELOCATABLE is set. In practice, this makes little difference,
>given that it defaults to 'y' and is a prerequisite for EFI_STUB and
>RANDOMIZE_BASE, but it will help with some future refactoring of the
>relocation code.
>
>Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
>---
> arch/x86/Kconfig | 40 ++++++++++++++++++------------
> arch/x86/boot/compressed/head_64.S | 4 ---
> arch/x86/boot/compressed/misc.c | 8 +++---
> arch/x86/boot/header.S | 8 ++----
> 4 files changed, 29 insertions(+), 31 deletions(-)
>
>diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
>index 58dce0b66179..c7427daa0c3e 100644
>--- a/arch/x86/Kconfig
>+++ b/arch/x86/Kconfig
>@@ -1898,7 +1898,7 @@ config EFI
> config EFI_STUB
> bool "EFI stub support"
> depends on EFI
>- select RELOCATABLE
>+ select RELOCATABLE if X86_32
> help
> This kernel feature allows a bzImage to be loaded directly
> by EFI firmware without the use of a bootloader.
>@@ -1995,8 +1995,9 @@ config PHYSICAL_START
> help
> This gives the physical address where the kernel is loaded.
>
>- If the kernel is not relocatable (CONFIG_RELOCATABLE=n) then bzImage
>- will decompress itself to above physical address and run from there.
>+ If the kernel is not relocatable (CONFIG_RELOCATABLE=n) and built for
>+ i386, then the bzImage will decompress itself to the above physical
>+ address and run from there.
> Otherwise, bzImage will run from the address where it has been loaded
> by the boot loader. The only exception is if it is loaded below the
> above physical address, in which case it will relocate itself there.
>@@ -2031,16 +2032,22 @@ config PHYSICAL_START
> Don't change this unless you know what you are doing.
>
> config RELOCATABLE
>- bool "Build a relocatable kernel"
>- default y
>+ bool "Build a relocatable kernel" if X86_32
>+ default X86_32
> help
>- This builds a kernel image that retains relocation information
>- so it can be loaded someplace besides the default 1MB.
>+ This builds a kernel image that retains relocation information so it
>+ can be placed someplace besides the default PAGE_OFFSET + 1MB. This
>+ is a prerequisite for KASLR.
> The relocations tend to make the kernel binary about 10% larger,
> but are discarded at runtime.
>
>- One use is for the kexec on panic case where the recovery kernel
>- must live at a different physical address than the primary
>+ On i386, where the virtual and physical load offset of the kernel
>+ must be equal, this also allows the kernel image to be placed at a
>+ physical load address that differs from the compile time default. On
>+ x86_64, this is always permitted.
>+
>+ One use is for the kexec on panic case on i386, where the recovery
>+ kernel must live at a different physical address than the primary
> kernel.
>
> Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
>@@ -2049,7 +2056,7 @@ config RELOCATABLE
>
> config RANDOMIZE_BASE
> bool "Randomize the address of the kernel image (KASLR)"
>- depends on RELOCATABLE
>+ select RELOCATABLE
> default y
> help
> In support of Kernel Address Space Layout Randomization (KASLR),
>@@ -2085,7 +2092,7 @@ config RANDOMIZE_BASE
> # Relocation on x86 needs some additional build support
> config X86_NEED_RELOCS
> def_bool y
>- depends on RANDOMIZE_BASE || (X86_32 && RELOCATABLE)
>+ depends on RELOCATABLE
> select ARCH_VMLINUX_NEEDS_RELOCS
>
> config PHYSICAL_ALIGN
>@@ -2098,12 +2105,13 @@ config PHYSICAL_ALIGN
> where kernel is loaded and run from. Kernel is compiled for an
> address which meets above alignment restriction.
>
>- If bootloader loads the kernel at a non-aligned address and
>- CONFIG_RELOCATABLE is set, kernel will move itself to nearest
>- address aligned to above value and run from there.
>+ If the bootloader loads the kernel at a non-aligned address and it
>+ is built for x86_64 or CONFIG_RELOCATABLE is set, the kernel will
>+ move itself to the nearest address aligned to above value and run
>+ from there.
>
>- If bootloader loads the kernel at a non-aligned address and
>- CONFIG_RELOCATABLE is not set, kernel will ignore the run time
>+ If the bootloader loads the i386 kernel at a non-aligned address and
>+ CONFIG_RELOCATABLE is not set, the kernel will ignore the run time
> load address and decompress itself to the address it has been
> compiled for and run from there. The address for which kernel is
> compiled already meets above alignment restrictions. Hence the
>diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S
>index 1aca51390f73..de1973f032c7 100644
>--- a/arch/x86/boot/compressed/head_64.S
>+++ b/arch/x86/boot/compressed/head_64.S
>@@ -143,7 +143,6 @@ SYM_FUNC_START(startup_32)
> * for safe in-place decompression.
> */
>
>-#ifdef CONFIG_RELOCATABLE
> movl %ebp, %ebx
> movl BP_kernel_alignment(%esi), %eax
> decl %eax
>@@ -152,7 +151,6 @@ SYM_FUNC_START(startup_32)
> andl %eax, %ebx
> cmpl $LOAD_PHYSICAL_ADDR, %ebx
> jae 1f
>-#endif
> movl $LOAD_PHYSICAL_ADDR, %ebx
> 1:
>
>@@ -316,7 +314,6 @@ SYM_CODE_START(startup_64)
> */
>
> /* Start with the delta to where the kernel will run at. */
>-#ifdef CONFIG_RELOCATABLE
> leaq startup_32(%rip) /* - $startup_32 */, %rbp
> movl BP_kernel_alignment(%rsi), %eax
> decl %eax
>@@ -325,7 +322,6 @@ SYM_CODE_START(startup_64)
> andq %rax, %rbp
> cmpq $LOAD_PHYSICAL_ADDR, %rbp
> jae 1f
>-#endif
> movq $LOAD_PHYSICAL_ADDR, %rbp
> 1:
>
>diff --git a/arch/x86/boot/compressed/misc.c b/arch/x86/boot/compressed/misc.c
>index 0f41ca0e52c0..d37569e7ee10 100644
>--- a/arch/x86/boot/compressed/misc.c
>+++ b/arch/x86/boot/compressed/misc.c
>@@ -314,12 +314,10 @@ static size_t parse_elf(void *output)
> if ((phdr->p_align % 0x200000) != 0)
> error("Alignment of LOAD segment isn't multiple of 2MB");
> #endif
>-#ifdef CONFIG_RELOCATABLE
>- dest = output;
>- dest += (phdr->p_paddr - LOAD_PHYSICAL_ADDR);
>-#else
> dest = (void *)(phdr->p_paddr);
>-#endif
>+ if (IS_ENABLED(CONFIG_X86_64) ||
>+ IS_ENABLED(CONFIG_RELOCATABLE))
>+ dest += (unsigned long)output - LOAD_PHYSICAL_ADDR;
> memmove(dest, output + phdr->p_offset, phdr->p_filesz);
> break;
> default: /* Ignore other PT_* */ break;
>diff --git a/arch/x86/boot/header.S b/arch/x86/boot/header.S
>index 9bea5a1e2c52..b72e6055e103 100644
>--- a/arch/x86/boot/header.S
>+++ b/arch/x86/boot/header.S
>@@ -332,7 +332,7 @@ initrd_addr_max: .long 0x7fffffff
> kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment
> #required for protected mode
> #kernel
>-#ifdef CONFIG_RELOCATABLE
>+#if defined(CONFIG_RELOCATABLE) || defined(CONFIG_X86_64)
> relocatable_kernel: .byte 1
> #else
> relocatable_kernel: .byte 0
>@@ -342,14 +342,10 @@ min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment
> xloadflags:
> #ifdef CONFIG_X86_64
> # define XLF0 XLF_KERNEL_64 /* 64-bit kernel */
>-#else
>-# define XLF0 0
>-#endif
>-
>-#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_X86_64)
> /* kernel/boot_param/ramdisk could be loaded above 4g */
> # define XLF1 XLF_CAN_BE_LOADED_ABOVE_4G
> #else
>+# define XLF0 0
> # define XLF1 0
> #endif
>
Can you clarify what these nebulous future improvements are?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-18 15:51 ` H. Peter Anvin
@ 2026-11-18 16:18 ` Ard Biesheuvel
2026-11-18 16:29 ` H. Peter Anvin
0 siblings, 1 reply; 9+ messages in thread
From: Ard Biesheuvel @ 2026-11-18 16:18 UTC (permalink / raw)
To: H . Peter Anvin, Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi
On Wed, 18 Nov 2026, at 16:51, H. Peter Anvin wrote:
> On November 11, 2026 1:18:44 AM PST, Ard Biesheuvel <ardb+git@google.com> wrote:
>>From: Ard Biesheuvel <ardb@kernel.org>
>>
>>On x86_64, the physical placement of the kernel is independent from its
>>mapping in the 'High Kernel Mapping' range. This means that even a
>>position dependent kernel built without boot-time relocation support can
>>run from any suitably aligned physical address, and there is no need to
>>make this behavior dependent on whether or not the kernel is virtually
>>relocatable.
>>
>>On i386, the situation is different, given that the physical and virtual
>>load offsets must be equal, and so only a relocatable kernel can be
>>loaded at a physical address that deviates from its build-time default.
>>
>>Clarify this in Kconfig and in the code, and advertise the 64-bit
>>bzImage as loadable at any physical offset regardless of whether
>>CONFIG_RELOCATABLE is set. In practice, this makes little difference,
>>given that it defaults to 'y' and is a prerequisite for EFI_STUB and
>>RANDOMIZE_BASE, but it will help with some future refactoring of the
>>relocation code.
>>
>>Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
>>---
>> arch/x86/Kconfig | 40 ++++++++++++++++++------------
>> arch/x86/boot/compressed/head_64.S | 4 ---
>> arch/x86/boot/compressed/misc.c | 8 +++---
>> arch/x86/boot/header.S | 8 ++----
>> 4 files changed, 29 insertions(+), 31 deletions(-)
>>
>>diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
>>index 58dce0b66179..c7427daa0c3e 100644
>>--- a/arch/x86/Kconfig
>>+++ b/arch/x86/Kconfig
>>@@ -1898,7 +1898,7 @@ config EFI
>> config EFI_STUB
>> bool "EFI stub support"
>> depends on EFI
>>- select RELOCATABLE
>>+ select RELOCATABLE if X86_32
>> help
>> This kernel feature allows a bzImage to be loaded directly
>> by EFI firmware without the use of a bootloader.
>>@@ -1995,8 +1995,9 @@ config PHYSICAL_START
>> help
>> This gives the physical address where the kernel is loaded.
>>
>>- If the kernel is not relocatable (CONFIG_RELOCATABLE=n) then bzImage
>>- will decompress itself to above physical address and run from there.
>>+ If the kernel is not relocatable (CONFIG_RELOCATABLE=n) and built for
>>+ i386, then the bzImage will decompress itself to the above physical
>>+ address and run from there.
>> Otherwise, bzImage will run from the address where it has been loaded
>> by the boot loader. The only exception is if it is loaded below the
>> above physical address, in which case it will relocate itself there.
>>@@ -2031,16 +2032,22 @@ config PHYSICAL_START
>> Don't change this unless you know what you are doing.
>>
>> config RELOCATABLE
>>- bool "Build a relocatable kernel"
>>- default y
>>+ bool "Build a relocatable kernel" if X86_32
>>+ default X86_32
>> help
>>- This builds a kernel image that retains relocation information
>>- so it can be loaded someplace besides the default 1MB.
>>+ This builds a kernel image that retains relocation information so it
>>+ can be placed someplace besides the default PAGE_OFFSET + 1MB. This
>>+ is a prerequisite for KASLR.
>> The relocations tend to make the kernel binary about 10% larger,
>> but are discarded at runtime.
>>
>>- One use is for the kexec on panic case where the recovery kernel
>>- must live at a different physical address than the primary
>>+ On i386, where the virtual and physical load offset of the kernel
>>+ must be equal, this also allows the kernel image to be placed at a
>>+ physical load address that differs from the compile time default. On
>>+ x86_64, this is always permitted.
>>+
>>+ One use is for the kexec on panic case on i386, where the recovery
>>+ kernel must live at a different physical address than the primary
>> kernel.
>>
>> Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
>>@@ -2049,7 +2056,7 @@ config RELOCATABLE
>>
>> config RANDOMIZE_BASE
>> bool "Randomize the address of the kernel image (KASLR)"
>>- depends on RELOCATABLE
>>+ select RELOCATABLE
>> default y
>> help
>> In support of Kernel Address Space Layout Randomization (KASLR),
>>@@ -2085,7 +2092,7 @@ config RANDOMIZE_BASE
>> # Relocation on x86 needs some additional build support
>> config X86_NEED_RELOCS
>> def_bool y
>>- depends on RANDOMIZE_BASE || (X86_32 && RELOCATABLE)
>>+ depends on RELOCATABLE
>> select ARCH_VMLINUX_NEEDS_RELOCS
>>
>> config PHYSICAL_ALIGN
>>@@ -2098,12 +2105,13 @@ config PHYSICAL_ALIGN
>> where kernel is loaded and run from. Kernel is compiled for an
>> address which meets above alignment restriction.
>>
>>- If bootloader loads the kernel at a non-aligned address and
>>- CONFIG_RELOCATABLE is set, kernel will move itself to nearest
>>- address aligned to above value and run from there.
>>+ If the bootloader loads the kernel at a non-aligned address and it
>>+ is built for x86_64 or CONFIG_RELOCATABLE is set, the kernel will
>>+ move itself to the nearest address aligned to above value and run
>>+ from there.
>>
>>- If bootloader loads the kernel at a non-aligned address and
>>- CONFIG_RELOCATABLE is not set, kernel will ignore the run time
>>+ If the bootloader loads the i386 kernel at a non-aligned address and
>>+ CONFIG_RELOCATABLE is not set, the kernel will ignore the run time
>> load address and decompress itself to the address it has been
>> compiled for and run from there. The address for which kernel is
>> compiled already meets above alignment restrictions. Hence the
>>diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S
>>index 1aca51390f73..de1973f032c7 100644
>>--- a/arch/x86/boot/compressed/head_64.S
>>+++ b/arch/x86/boot/compressed/head_64.S
>>@@ -143,7 +143,6 @@ SYM_FUNC_START(startup_32)
>> * for safe in-place decompression.
>> */
>>
>>-#ifdef CONFIG_RELOCATABLE
>> movl %ebp, %ebx
>> movl BP_kernel_alignment(%esi), %eax
>> decl %eax
>>@@ -152,7 +151,6 @@ SYM_FUNC_START(startup_32)
>> andl %eax, %ebx
>> cmpl $LOAD_PHYSICAL_ADDR, %ebx
>> jae 1f
>>-#endif
>> movl $LOAD_PHYSICAL_ADDR, %ebx
>> 1:
>>
>>@@ -316,7 +314,6 @@ SYM_CODE_START(startup_64)
>> */
>>
>> /* Start with the delta to where the kernel will run at. */
>>-#ifdef CONFIG_RELOCATABLE
>> leaq startup_32(%rip) /* - $startup_32 */, %rbp
>> movl BP_kernel_alignment(%rsi), %eax
>> decl %eax
>>@@ -325,7 +322,6 @@ SYM_CODE_START(startup_64)
>> andq %rax, %rbp
>> cmpq $LOAD_PHYSICAL_ADDR, %rbp
>> jae 1f
>>-#endif
>> movq $LOAD_PHYSICAL_ADDR, %rbp
>> 1:
>>
>>diff --git a/arch/x86/boot/compressed/misc.c b/arch/x86/boot/compressed/misc.c
>>index 0f41ca0e52c0..d37569e7ee10 100644
>>--- a/arch/x86/boot/compressed/misc.c
>>+++ b/arch/x86/boot/compressed/misc.c
>>@@ -314,12 +314,10 @@ static size_t parse_elf(void *output)
>> if ((phdr->p_align % 0x200000) != 0)
>> error("Alignment of LOAD segment isn't multiple of 2MB");
>> #endif
>>-#ifdef CONFIG_RELOCATABLE
>>- dest = output;
>>- dest += (phdr->p_paddr - LOAD_PHYSICAL_ADDR);
>>-#else
>> dest = (void *)(phdr->p_paddr);
>>-#endif
>>+ if (IS_ENABLED(CONFIG_X86_64) ||
>>+ IS_ENABLED(CONFIG_RELOCATABLE))
>>+ dest += (unsigned long)output - LOAD_PHYSICAL_ADDR;
>> memmove(dest, output + phdr->p_offset, phdr->p_filesz);
>> break;
>> default: /* Ignore other PT_* */ break;
>>diff --git a/arch/x86/boot/header.S b/arch/x86/boot/header.S
>>index 9bea5a1e2c52..b72e6055e103 100644
>>--- a/arch/x86/boot/header.S
>>+++ b/arch/x86/boot/header.S
>>@@ -332,7 +332,7 @@ initrd_addr_max: .long 0x7fffffff
>> kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment
>> #required for protected mode
>> #kernel
>>-#ifdef CONFIG_RELOCATABLE
>>+#if defined(CONFIG_RELOCATABLE) || defined(CONFIG_X86_64)
>> relocatable_kernel: .byte 1
>> #else
>> relocatable_kernel: .byte 0
>>@@ -342,14 +342,10 @@ min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment
>> xloadflags:
>> #ifdef CONFIG_X86_64
>> # define XLF0 XLF_KERNEL_64 /* 64-bit kernel */
>>-#else
>>-# define XLF0 0
>>-#endif
>>-
>>-#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_X86_64)
>> /* kernel/boot_param/ramdisk could be loaded above 4g */
>> # define XLF1 XLF_CAN_BE_LOADED_ABOVE_4G
>> #else
>>+# define XLF0 0
>> # define XLF1 0
>> #endif
>>
>
> Can you clarify what these nebulous future improvements are?
The main improvement today is that CONFIG_RELOCATABLE will be
only implied by CONFIG_RANDOMIZE_BASE, and so turning that off
gets rid of the unnecessary relocation metadata.
The future improvement is still fgKASLR, which I am implementing
in the ELF domain, making it arch-agnostic, and applicable to
other static ELF executables such as hypervisors and statically
linked user space executables. This will hopefully make the
needed tooling changes more palatable to the wider community.
On x86, that will require the use of PIC code for kaslr capable
kernels, [which surely you remember having discussed with me in
the past], but only when opting in to kaslr/fgkaslr. Otherwise,
the usual position dependent codegen will be preserved.
Note that I have extensive benchmarking data now that shows that
the PIC change itself has negligible impact for performance, but
having the option to turn that off if you don't need it is still
appreciated, I assume. But let's leave that discussion for when
I resend that particular series.
--
Ard.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-18 16:18 ` Ard Biesheuvel
@ 2026-11-18 16:29 ` H. Peter Anvin
2026-11-18 16:55 ` Ard Biesheuvel
0 siblings, 1 reply; 9+ messages in thread
From: H. Peter Anvin @ 2026-11-18 16:29 UTC (permalink / raw)
To: Ard Biesheuvel, Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi
On November 18, 2026 8:18:44 AM PST, Ard Biesheuvel <ardb@kernel.org> wrote:
>
>
>On Wed, 18 Nov 2026, at 16:51, H. Peter Anvin wrote:
>> On November 11, 2026 1:18:44 AM PST, Ard Biesheuvel <ardb+git@google.com> wrote:
>>>From: Ard Biesheuvel <ardb@kernel.org>
>>>
>>>On x86_64, the physical placement of the kernel is independent from its
>>>mapping in the 'High Kernel Mapping' range. This means that even a
>>>position dependent kernel built without boot-time relocation support can
>>>run from any suitably aligned physical address, and there is no need to
>>>make this behavior dependent on whether or not the kernel is virtually
>>>relocatable.
>>>
>>>On i386, the situation is different, given that the physical and virtual
>>>load offsets must be equal, and so only a relocatable kernel can be
>>>loaded at a physical address that deviates from its build-time default.
>>>
>>>Clarify this in Kconfig and in the code, and advertise the 64-bit
>>>bzImage as loadable at any physical offset regardless of whether
>>>CONFIG_RELOCATABLE is set. In practice, this makes little difference,
>>>given that it defaults to 'y' and is a prerequisite for EFI_STUB and
>>>RANDOMIZE_BASE, but it will help with some future refactoring of the
>>>relocation code.
>>>
>>>Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
>>>---
>>> arch/x86/Kconfig | 40 ++++++++++++++++++------------
>>> arch/x86/boot/compressed/head_64.S | 4 ---
>>> arch/x86/boot/compressed/misc.c | 8 +++---
>>> arch/x86/boot/header.S | 8 ++----
>>> 4 files changed, 29 insertions(+), 31 deletions(-)
>>>
>>>diff --git a/arch/x86/Kconfig b/arch/x86/Kconfig
>>>index 58dce0b66179..c7427daa0c3e 100644
>>>--- a/arch/x86/Kconfig
>>>+++ b/arch/x86/Kconfig
>>>@@ -1898,7 +1898,7 @@ config EFI
>>> config EFI_STUB
>>> bool "EFI stub support"
>>> depends on EFI
>>>- select RELOCATABLE
>>>+ select RELOCATABLE if X86_32
>>> help
>>> This kernel feature allows a bzImage to be loaded directly
>>> by EFI firmware without the use of a bootloader.
>>>@@ -1995,8 +1995,9 @@ config PHYSICAL_START
>>> help
>>> This gives the physical address where the kernel is loaded.
>>>
>>>- If the kernel is not relocatable (CONFIG_RELOCATABLE=n) then bzImage
>>>- will decompress itself to above physical address and run from there.
>>>+ If the kernel is not relocatable (CONFIG_RELOCATABLE=n) and built for
>>>+ i386, then the bzImage will decompress itself to the above physical
>>>+ address and run from there.
>>> Otherwise, bzImage will run from the address where it has been loaded
>>> by the boot loader. The only exception is if it is loaded below the
>>> above physical address, in which case it will relocate itself there.
>>>@@ -2031,16 +2032,22 @@ config PHYSICAL_START
>>> Don't change this unless you know what you are doing.
>>>
>>> config RELOCATABLE
>>>- bool "Build a relocatable kernel"
>>>- default y
>>>+ bool "Build a relocatable kernel" if X86_32
>>>+ default X86_32
>>> help
>>>- This builds a kernel image that retains relocation information
>>>- so it can be loaded someplace besides the default 1MB.
>>>+ This builds a kernel image that retains relocation information so it
>>>+ can be placed someplace besides the default PAGE_OFFSET + 1MB. This
>>>+ is a prerequisite for KASLR.
>>> The relocations tend to make the kernel binary about 10% larger,
>>> but are discarded at runtime.
>>>
>>>- One use is for the kexec on panic case where the recovery kernel
>>>- must live at a different physical address than the primary
>>>+ On i386, where the virtual and physical load offset of the kernel
>>>+ must be equal, this also allows the kernel image to be placed at a
>>>+ physical load address that differs from the compile time default. On
>>>+ x86_64, this is always permitted.
>>>+
>>>+ One use is for the kexec on panic case on i386, where the recovery
>>>+ kernel must live at a different physical address than the primary
>>> kernel.
>>>
>>> Note: If CONFIG_RELOCATABLE=y, then the kernel runs from the address
>>>@@ -2049,7 +2056,7 @@ config RELOCATABLE
>>>
>>> config RANDOMIZE_BASE
>>> bool "Randomize the address of the kernel image (KASLR)"
>>>- depends on RELOCATABLE
>>>+ select RELOCATABLE
>>> default y
>>> help
>>> In support of Kernel Address Space Layout Randomization (KASLR),
>>>@@ -2085,7 +2092,7 @@ config RANDOMIZE_BASE
>>> # Relocation on x86 needs some additional build support
>>> config X86_NEED_RELOCS
>>> def_bool y
>>>- depends on RANDOMIZE_BASE || (X86_32 && RELOCATABLE)
>>>+ depends on RELOCATABLE
>>> select ARCH_VMLINUX_NEEDS_RELOCS
>>>
>>> config PHYSICAL_ALIGN
>>>@@ -2098,12 +2105,13 @@ config PHYSICAL_ALIGN
>>> where kernel is loaded and run from. Kernel is compiled for an
>>> address which meets above alignment restriction.
>>>
>>>- If bootloader loads the kernel at a non-aligned address and
>>>- CONFIG_RELOCATABLE is set, kernel will move itself to nearest
>>>- address aligned to above value and run from there.
>>>+ If the bootloader loads the kernel at a non-aligned address and it
>>>+ is built for x86_64 or CONFIG_RELOCATABLE is set, the kernel will
>>>+ move itself to the nearest address aligned to above value and run
>>>+ from there.
>>>
>>>- If bootloader loads the kernel at a non-aligned address and
>>>- CONFIG_RELOCATABLE is not set, kernel will ignore the run time
>>>+ If the bootloader loads the i386 kernel at a non-aligned address and
>>>+ CONFIG_RELOCATABLE is not set, the kernel will ignore the run time
>>> load address and decompress itself to the address it has been
>>> compiled for and run from there. The address for which kernel is
>>> compiled already meets above alignment restrictions. Hence the
>>>diff --git a/arch/x86/boot/compressed/head_64.S b/arch/x86/boot/compressed/head_64.S
>>>index 1aca51390f73..de1973f032c7 100644
>>>--- a/arch/x86/boot/compressed/head_64.S
>>>+++ b/arch/x86/boot/compressed/head_64.S
>>>@@ -143,7 +143,6 @@ SYM_FUNC_START(startup_32)
>>> * for safe in-place decompression.
>>> */
>>>
>>>-#ifdef CONFIG_RELOCATABLE
>>> movl %ebp, %ebx
>>> movl BP_kernel_alignment(%esi), %eax
>>> decl %eax
>>>@@ -152,7 +151,6 @@ SYM_FUNC_START(startup_32)
>>> andl %eax, %ebx
>>> cmpl $LOAD_PHYSICAL_ADDR, %ebx
>>> jae 1f
>>>-#endif
>>> movl $LOAD_PHYSICAL_ADDR, %ebx
>>> 1:
>>>
>>>@@ -316,7 +314,6 @@ SYM_CODE_START(startup_64)
>>> */
>>>
>>> /* Start with the delta to where the kernel will run at. */
>>>-#ifdef CONFIG_RELOCATABLE
>>> leaq startup_32(%rip) /* - $startup_32 */, %rbp
>>> movl BP_kernel_alignment(%rsi), %eax
>>> decl %eax
>>>@@ -325,7 +322,6 @@ SYM_CODE_START(startup_64)
>>> andq %rax, %rbp
>>> cmpq $LOAD_PHYSICAL_ADDR, %rbp
>>> jae 1f
>>>-#endif
>>> movq $LOAD_PHYSICAL_ADDR, %rbp
>>> 1:
>>>
>>>diff --git a/arch/x86/boot/compressed/misc.c b/arch/x86/boot/compressed/misc.c
>>>index 0f41ca0e52c0..d37569e7ee10 100644
>>>--- a/arch/x86/boot/compressed/misc.c
>>>+++ b/arch/x86/boot/compressed/misc.c
>>>@@ -314,12 +314,10 @@ static size_t parse_elf(void *output)
>>> if ((phdr->p_align % 0x200000) != 0)
>>> error("Alignment of LOAD segment isn't multiple of 2MB");
>>> #endif
>>>-#ifdef CONFIG_RELOCATABLE
>>>- dest = output;
>>>- dest += (phdr->p_paddr - LOAD_PHYSICAL_ADDR);
>>>-#else
>>> dest = (void *)(phdr->p_paddr);
>>>-#endif
>>>+ if (IS_ENABLED(CONFIG_X86_64) ||
>>>+ IS_ENABLED(CONFIG_RELOCATABLE))
>>>+ dest += (unsigned long)output - LOAD_PHYSICAL_ADDR;
>>> memmove(dest, output + phdr->p_offset, phdr->p_filesz);
>>> break;
>>> default: /* Ignore other PT_* */ break;
>>>diff --git a/arch/x86/boot/header.S b/arch/x86/boot/header.S
>>>index 9bea5a1e2c52..b72e6055e103 100644
>>>--- a/arch/x86/boot/header.S
>>>+++ b/arch/x86/boot/header.S
>>>@@ -332,7 +332,7 @@ initrd_addr_max: .long 0x7fffffff
>>> kernel_alignment: .long CONFIG_PHYSICAL_ALIGN #physical addr alignment
>>> #required for protected mode
>>> #kernel
>>>-#ifdef CONFIG_RELOCATABLE
>>>+#if defined(CONFIG_RELOCATABLE) || defined(CONFIG_X86_64)
>>> relocatable_kernel: .byte 1
>>> #else
>>> relocatable_kernel: .byte 0
>>>@@ -342,14 +342,10 @@ min_alignment: .byte MIN_KERNEL_ALIGN_LG2 # minimum alignment
>>> xloadflags:
>>> #ifdef CONFIG_X86_64
>>> # define XLF0 XLF_KERNEL_64 /* 64-bit kernel */
>>>-#else
>>>-# define XLF0 0
>>>-#endif
>>>-
>>>-#if defined(CONFIG_RELOCATABLE) && defined(CONFIG_X86_64)
>>> /* kernel/boot_param/ramdisk could be loaded above 4g */
>>> # define XLF1 XLF_CAN_BE_LOADED_ABOVE_4G
>>> #else
>>>+# define XLF0 0
>>> # define XLF1 0
>>> #endif
>>>
>>
>> Can you clarify what these nebulous future improvements are?
>
>The main improvement today is that CONFIG_RELOCATABLE will be
>only implied by CONFIG_RANDOMIZE_BASE, and so turning that off
>gets rid of the unnecessary relocation metadata.
>
>The future improvement is still fgKASLR, which I am implementing
>in the ELF domain, making it arch-agnostic, and applicable to
>other static ELF executables such as hypervisors and statically
>linked user space executables. This will hopefully make the
>needed tooling changes more palatable to the wider community.
>
>On x86, that will require the use of PIC code for kaslr capable
>kernels, [which surely you remember having discussed with me in
>the past], but only when opting in to kaslr/fgkaslr. Otherwise,
>the usual position dependent codegen will be preserved.
>
>Note that I have extensive benchmarking data now that shows that
>the PIC change itself has negligible impact for performance, but
>having the option to turn that off if you don't need it is still
>appreciated, I assume. But let's leave that discussion for when
>I resend that particular series.
>
So since you're not going to get people to stop using kASLR, you're now going a different path to forcing everyone to build with PIC?
I'm going to vote NAK on this one... I was already thinking that it would mess up low-level debugging too much, but when *handwave handwave future improvement* turns into "the thing that has been NAKed several times already", then...
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-18 16:29 ` H. Peter Anvin
@ 2026-11-18 16:55 ` Ard Biesheuvel
2026-11-18 17:04 ` H. Peter Anvin
0 siblings, 1 reply; 9+ messages in thread
From: Ard Biesheuvel @ 2026-11-18 16:55 UTC (permalink / raw)
To: H . Peter Anvin, Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi
On Wed, 18 Nov 2026, at 17:29, H. Peter Anvin wrote:
> On November 18, 2026 8:18:44 AM PST, Ard Biesheuvel <ardb@kernel.org> wrote:
>>
>>
>>On Wed, 18 Nov 2026, at 16:51, H. Peter Anvin wrote:
>>> On November 11, 2026 1:18:44 AM PST, Ard Biesheuvel <ardb+git@google.com> wrote:
>>>>From: Ard Biesheuvel <ardb@kernel.org>
>>>>
>>>>On x86_64, the physical placement of the kernel is independent from its
>>>>mapping in the 'High Kernel Mapping' range. This means that even a
>>>>position dependent kernel built without boot-time relocation support can
>>>>run from any suitably aligned physical address, and there is no need to
>>>>make this behavior dependent on whether or not the kernel is virtually
>>>>relocatable.
>>>>
>>>>On i386, the situation is different, given that the physical and virtual
>>>>load offsets must be equal, and so only a relocatable kernel can be
>>>>loaded at a physical address that deviates from its build-time default.
>>>>
>>>>Clarify this in Kconfig and in the code, and advertise the 64-bit
>>>>bzImage as loadable at any physical offset regardless of whether
>>>>CONFIG_RELOCATABLE is set. In practice, this makes little difference,
>>>>given that it defaults to 'y' and is a prerequisite for EFI_STUB and
>>>>RANDOMIZE_BASE, but it will help with some future refactoring of the
>>>>relocation code.
>>>>
>>>>Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
>>>>---
>>>> arch/x86/Kconfig | 40 ++++++++++++++++++------------
>>>> arch/x86/boot/compressed/head_64.S | 4 ---
>>>> arch/x86/boot/compressed/misc.c | 8 +++---
>>>> arch/x86/boot/header.S | 8 ++----
>>>> 4 files changed, 29 insertions(+), 31 deletions(-)
>>>>
...
> I'm going to vote NAK on this one... I was already thinking that it
> would mess up low-level debugging too much,
How so? The last time I proposed this, you replied that you were
planning to do this yourself.
https://lore.kernel.org/all/3f2e8d7c-6029-49ef-8e31-a3eb5efb385b@zytor.com/
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-18 16:55 ` Ard Biesheuvel
@ 2026-11-18 17:04 ` H. Peter Anvin
2026-11-18 17:26 ` Ard Biesheuvel
0 siblings, 1 reply; 9+ messages in thread
From: H. Peter Anvin @ 2026-11-18 17:04 UTC (permalink / raw)
To: Ard Biesheuvel, Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi
On November 18, 2026 8:55:11 AM PST, Ard Biesheuvel <ardb@kernel.org> wrote:
>
>
>On Wed, 18 Nov 2026, at 17:29, H. Peter Anvin wrote:
>> On November 18, 2026 8:18:44 AM PST, Ard Biesheuvel <ardb@kernel.org> wrote:
>>>
>>>
>>>On Wed, 18 Nov 2026, at 16:51, H. Peter Anvin wrote:
>>>> On November 11, 2026 1:18:44 AM PST, Ard Biesheuvel <ardb+git@google.com> wrote:
>>>>>From: Ard Biesheuvel <ardb@kernel.org>
>>>>>
>>>>>On x86_64, the physical placement of the kernel is independent from its
>>>>>mapping in the 'High Kernel Mapping' range. This means that even a
>>>>>position dependent kernel built without boot-time relocation support can
>>>>>run from any suitably aligned physical address, and there is no need to
>>>>>make this behavior dependent on whether or not the kernel is virtually
>>>>>relocatable.
>>>>>
>>>>>On i386, the situation is different, given that the physical and virtual
>>>>>load offsets must be equal, and so only a relocatable kernel can be
>>>>>loaded at a physical address that deviates from its build-time default.
>>>>>
>>>>>Clarify this in Kconfig and in the code, and advertise the 64-bit
>>>>>bzImage as loadable at any physical offset regardless of whether
>>>>>CONFIG_RELOCATABLE is set. In practice, this makes little difference,
>>>>>given that it defaults to 'y' and is a prerequisite for EFI_STUB and
>>>>>RANDOMIZE_BASE, but it will help with some future refactoring of the
>>>>>relocation code.
>>>>>
>>>>>Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
>>>>>---
>>>>> arch/x86/Kconfig | 40 ++++++++++++++++++------------
>>>>> arch/x86/boot/compressed/head_64.S | 4 ---
>>>>> arch/x86/boot/compressed/misc.c | 8 +++---
>>>>> arch/x86/boot/header.S | 8 ++----
>>>>> 4 files changed, 29 insertions(+), 31 deletions(-)
>>>>>
>...
>> I'm going to vote NAK on this one... I was already thinking that it
>> would mess up low-level debugging too much,
>
>How so? The last time I proposed this, you replied that you were
>planning to do this yourself.
>
>https://lore.kernel.org/all/3f2e8d7c-6029-49ef-8e31-a3eb5efb385b@zytor.com/
>
If we are going to get rid of it, we should get rid of it properly as in removing the conditional machinery, not use it as a backdoor for doing something explicitly NAKed (forcing PIC compilation.)
What you are proposing is literally the exact opposite.
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-18 17:04 ` H. Peter Anvin
@ 2026-11-18 17:26 ` Ard Biesheuvel
2026-11-18 19:35 ` H. Peter Anvin
0 siblings, 1 reply; 9+ messages in thread
From: Ard Biesheuvel @ 2026-11-18 17:26 UTC (permalink / raw)
To: H . Peter Anvin, Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi
On Wed, 18 Nov 2026, at 18:04, H. Peter Anvin wrote:
> On November 18, 2026 8:55:11 AM PST, Ard Biesheuvel <ardb@kernel.org> wrote:
>>
>>
>>On Wed, 18 Nov 2026, at 17:29, H. Peter Anvin wrote:
>>> On November 18, 2026 8:18:44 AM PST, Ard Biesheuvel <ardb@kernel.org> wrote:
>>>>
>>>>
>>>>On Wed, 18 Nov 2026, at 16:51, H. Peter Anvin wrote:
>>>>> On November 11, 2026 1:18:44 AM PST, Ard Biesheuvel <ardb+git@google.com> wrote:
>>>>>>From: Ard Biesheuvel <ardb@kernel.org>
>>>>>>
>>>>>>On x86_64, the physical placement of the kernel is independent from its
>>>>>>mapping in the 'High Kernel Mapping' range. This means that even a
>>>>>>position dependent kernel built without boot-time relocation support can
>>>>>>run from any suitably aligned physical address, and there is no need to
>>>>>>make this behavior dependent on whether or not the kernel is virtually
>>>>>>relocatable.
>>>>>>
>>>>>>On i386, the situation is different, given that the physical and virtual
>>>>>>load offsets must be equal, and so only a relocatable kernel can be
>>>>>>loaded at a physical address that deviates from its build-time default.
>>>>>>
>>>>>>Clarify this in Kconfig and in the code, and advertise the 64-bit
>>>>>>bzImage as loadable at any physical offset regardless of whether
>>>>>>CONFIG_RELOCATABLE is set. In practice, this makes little difference,
>>>>>>given that it defaults to 'y' and is a prerequisite for EFI_STUB and
>>>>>>RANDOMIZE_BASE, but it will help with some future refactoring of the
>>>>>>relocation code.
>>>>>>
>>>>>>Signed-off-by: Ard Biesheuvel <ardb@kernel.org>
>>>>>>---
>>>>>> arch/x86/Kconfig | 40 ++++++++++++++++++------------
>>>>>> arch/x86/boot/compressed/head_64.S | 4 ---
>>>>>> arch/x86/boot/compressed/misc.c | 8 +++---
>>>>>> arch/x86/boot/header.S | 8 ++----
>>>>>> 4 files changed, 29 insertions(+), 31 deletions(-)
>>>>>>
>>...
>>> I'm going to vote NAK on this one... I was already thinking that it
>>> would mess up low-level debugging too much,
>>
>>How so? The last time I proposed this, you replied that you were
>>planning to do this yourself.
>>
>>https://lore.kernel.org/all/3f2e8d7c-6029-49ef-8e31-a3eb5efb385b@zytor.com/
>>
>
> If we are going to get rid of it, we should get rid of it properly as
> in removing the conditional machinery,
Which conditional machinery is that? All the code that reasons about the
physical load address needs to stay, the only thing I am changing here
is that you can no longer disable it on x86_64, as there is no upside to
forcing the 64-bit kernel to run from a fixed physical address. This
means the EFI stub no longer needs to depend on CONFIG_RELOCATABLE
(which also controls the generation for relocation data for virtual
displacement) for x86_64.
The i386 situation is different, but I left that alone on purpose.
Would you prefer it if that always became relocatable as well?
> not use it as a backdoor for
> doing something explicitly NAKed (forcing PIC compilation.)
>
I know PIC compilation is a sensitive subject for some people, but
would you mind not framing this as some backhanded action on my part?
Once I get to resending that series, you will have ample opportunity
to voice your concerns and suggest workloads that will prove that
it is infeasible. Or even provide one now so that I won't have to
bother resending it in the first place.
> What you are proposing is literally the exact opposite.
I don't think so, but I'm still not sure what you meant by "it
would mess up low-level debugging too much", so maybe you could
clarify that?
^ permalink raw reply [flat|nested] 9+ messages in thread
* Re: [PATCH] x86: Make the 64-bit bzImage always physically relocatable
2026-11-18 17:26 ` Ard Biesheuvel
@ 2026-11-18 19:35 ` H. Peter Anvin
0 siblings, 0 replies; 9+ messages in thread
From: H. Peter Anvin @ 2026-11-18 19:35 UTC (permalink / raw)
To: Ard Biesheuvel, Ard Biesheuvel, x86; +Cc: linux-kernel, linux-efi
On 2026-11-18 09:26, Ard Biesheuvel wrote:
>>> ...
>>>> I'm going to vote NAK on this one... I was already thinking that it
>>>> would mess up low-level debugging too much,
>>>
>>> How so? The last time I proposed this, you replied that you were
>>> planning to do this yourself.
>>>
>>> https://lore.kernel.org/all/3f2e8d7c-6029-49ef-8e31-a3eb5efb385b@zytor.com/
>>>
>>
>> If we are going to get rid of it, we should get rid of it properly as
>> in removing the conditional machinery,
>
> Which conditional machinery is that? All the code that reasons about the
> physical load address needs to stay, the only thing I am changing here
> is that you can no longer disable it on x86_64, as there is no upside to
> forcing the 64-bit kernel to run from a fixed physical address. This
> means the EFI stub no longer needs to depend on CONFIG_RELOCATABLE
> (which also controls the generation for relocation data for virtual
> displacement) for x86_64.
>
> The i386 situation is different, but I left that alone on purpose.
> Would you prefer it if that always became relocatable as well?
>
Yes, if we're going to do it, it would make more sense to do exactly that.
>> not use it as a backdoor for
>> doing something explicitly NAKed (forcing PIC compilation.)
>>
>
> I know PIC compilation is a sensitive subject for some people, but
> would you mind not framing this as some backhanded action on my part?
>
> Once I get to resending that series, you will have ample opportunity
> to voice your concerns and suggest workloads that will prove that
> it is infeasible. Or even provide one now so that I won't have to
> bother resending it in the first place.
I do (genuinely) apologize; that was indeed *quite* uncalled for.
What I *do* think is a real problem -- and you are far from the only or
worst offender -- is to put a vague "future improvements" as
justification for a change. This is literally asking people to take on
faith that the "future improvements" is actually an engineering
direction we want to go in.
The following points are in no way specific to your proposals, so please
don't take it that way; these are more general statements about "why x86
is special".
I do not believe in is pessimizing one of the most widely used
architectures in the world in the name of "uniformity" or
"compatibility", and there have been many, genuinely well-meaning,
attempts to do so. If x86 were a niche architecture that would be a
*very* different thing, but in the world we are living in right now,
there is x86 and ARM; everything else is a rounding error (long tail).
As such, for either of those architectures to carry more arch-specific
stuff than other architectures is entirely fair.
Now, x86 and ARM are two very different beasts, which is entirely
natural because they have evolved into their current market dominance
through completely different routes. As such, ARM has a lot more
*platform* divergences than x86 does, and that means it has has a lot of
overlap with most other "platform rich" architectures. Here, ARM sits
squarely with the long tail, and so it makes sense to strive for ARM to
drive, cooperatively, where the other architectures go.
Here, the odd ones out are x86 and s390: they are architectures which
have a dominant -- to the point of being universal -- *systems*
architecture as well as a CPU architecture. This means that especially
the early flows are heavily influenced by that systems architecture in
ways other architectures aren't. This tight binding of systems
architecture are a major aspect of those architectures which is very
easy to forget.
>> What you are proposing is literally the exact opposite.
>
> I don't think so, but I'm still not sure what you meant by "it
> would mess up low-level debugging too much", so maybe you could
> clarify that?
Certainly.
When I debug the early (1:1-mapped) flows I often find it useful to pin
down the kernel to a specific address so that I don't have to convert
between ELF addresses and physical addresses (for this purpose, I don't
care about significant hex digits larger than the size of the kernel,
which is *one* reason why kernel alignment moved to 16 MiB -- another
reason was the somewhat special nature of the lower 16 MiB of the
address space on some x86 systems.) Once we are running under the kernel
mappings, it is just a matter of of turning off kASLR.
Now, you also quite correctly pointed out that I already proposed
turning on kernel relocation by default. In practice it doesn't become a
problem, as the kernel generally ends up loaded at 16 MiB in a legacy
environment, and in an EFI environment you have to deal with the memory
space EFI assigns you no matter what you do.
PIC compilation is another matter entirely (as you also very correctly
point out!), as x86 unlike most RISC architectures has enough direct
addressing reach to encompass the entire kernel (in the "medium" model
for user space and the "kernel" model for kernel space.) This means that
x86 benefits from GOT/PLT elision in ways that many other architectures
don't. On the flipside, because x86 is a CISC architecture once you give
atup performance in the compiler stage it is very hard to recover it
even in the linker stage. Furthermore, on i386 PIC is *extremely*
painful since it involves giving up one of only 7 usable GPRs (6 if you
are compiling with frame pointers!) and a relatively expensive
sequence(*) to get EIP manifest.
As a result, I very much will continue to object to PIC compilation on
x86 as opposed to boot time relocation. Whereas code patching in user
space is expensive due to breaking sharing and thus demand paging of
executables and libraries, none of that applies to the kernel -- and we
do runtime code patching of the kernel anyway. The relocation is just a
special case of that.
Now I do know you don't like the compressed kernel relocation format
(which you are not trying to change with this patch) and it is *most
certainly* insufficiently expressive for fgKASLR. For fgKASLR you need
to know the relocation base rather than a simple adjustment factor, even
on an architecture like x86 that doesn't have to deal with "upper
part"-type relocations (for which the compressed format approach,
carrying embedded addends, completely collapses.) The metadata required
by fgKASLR is positively vast in comparison to the ordinary kernel boot,
and legitimately so.
However, fgKALSR is time-consuming. On bare metal this is rarely a
concern, but users want to be able to spin up a VM kernel in ~100 ms. In
that case, the compressed relocation format is highly efficient, both
since it is compact and since the processing of those relocations is
extremely simple. Furthermore, since the kernel is also ready to go if
loaded at its advertised preferred address (which is the reason why this
address is explicitly advertised, even for a relocatable kernel: "if you
can load me at this specific address, I can boot faster and your vmlinux
symbols will match the runtime, too."), the performance-sensitive VM
spinup the (virtual) environment can be set up so that the relocation
can be skipped entirely.
-hpa
(*) That being said, the use of an out-of-line trampoline to do so is a
thing that was only relevant on a small handful of cores that
unfortunately fell right at the end of the true 32-bit era; on both
older and newer cores CALL 0 is special cased to be a "PUSH xIP"
instruction and does not mess up the call stack. It still costs a
register, and if using PLT, requires that register to be %ebx, which
further adds to the complexity; if %ebx was *permanently* assigned to
this role like the gp register on (some) RISC architectures it might
actually be less painful, but losing one register out of 7 is going to
hurt like hell no matter how you slice it.
-hpa
^ permalink raw reply [flat|nested] 9+ messages in thread
end of thread, other threads:[~2026-11-18 19:36 UTC | newest]
Thread overview: 9+ messages (download: mbox.gz / follow: Atom feed)
-- links below jump to the message on this page --
2026-11-11 9:18 [PATCH] x86: Make the 64-bit bzImage always physically relocatable Ard Biesheuvel
2026-11-18 11:23 ` Ard Biesheuvel
2026-11-18 15:51 ` H. Peter Anvin
2026-11-18 16:18 ` Ard Biesheuvel
2026-11-18 16:29 ` H. Peter Anvin
2026-11-18 16:55 ` Ard Biesheuvel
2026-11-18 17:04 ` H. Peter Anvin
2026-11-18 17:26 ` Ard Biesheuvel
2026-11-18 19:35 ` H. Peter Anvin
This is a public inbox, see mirroring instructions
for how to clone and mirror all data and code used for this inbox
all inboxes | Powered by JetHome®